Related
Firstly I would like to say thanks to this site and the trinityguides.info site for the great work people have being doing and making available to everybody, it is great being able to use my trinity with wm6, keep the good work going!
Now the issue I seem to be hitting the same "error [260] connection" every time I attempt to update anything on my Trinity. I have followed the advice on the trinityguides site regarding being stuck in bootloader mode to no avail, and I can't seem to find anything in the posts on the xda site which will rectify the issue.
Previously I have been able to update to AX3L v2.8.01 version without any problems, but I decided to update to sammy's ultra light, it initially kicks into des' crashproof sspl, but then it can't connect to the pc. even when I manually enter olipro's hard-spl it does the same. I have tried to re-install hard-spl, but can't. Disconnecting the usb option in the activesync settings doesn't do anything either. Does anybody have any suggestions for me please?
I am not even too sure if my trinity should have both Des' crashproof and hard-spl on it at the same time? Could someone advise me on whether this is alright please?
the tech details:
Trinity
AX3L_OS_v2.0.8.2
radio - 1.46.30 (even though it doesn't say this in the device info, or boot screen after soft reset)
Home PC - XP (just in case)
Did you also try flashing it again, the ROM I mean. I have this error also but as soon as I execute the ROM flash again it finds the device and starts flashing:
http://forum.xda-developers.com/showpost.php?p=1449597&postcount=2
I am assuming you mean flash with the new ROM, sammy's in my case?
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
No, I am in the same situation. The first attempt puts the device in 'ipl-sspl by des' bootloader mode then after about 10 seconds or so the error[260] is displayed on the pc. If I exit the ruu app and attempt again, nothing new happens on the trinity (i.e. it is still in Des bootloader) and the message is displayed again.
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
What operating system en activesync are you using?
On the PC I am using XP and Activesync 4.5
Check your connection settings to accept USB connections. Also, try using Hard-SPL 1.30 before flashing the ROM again.
deejacker said:
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
Click to expand...
Click to collapse
In your PC, try another USB connection.
BLOODY HELL!!! It is the simplest things which we often forget to try. Thanks Jotam for pointing out an obvious point, it must have needed a re-plug of the usb cable into another port for the pc to pick up the device again. I will remember that for future updates so I don't make a dumb ass of myself again. Thanks guys/gals.
Vista
Using Vista? if so which version?
Hi I asked this question yesterday, I am a noob :-[ but the only difference is I'm using Vista Ultimate.
Just for others who have the problem.
When you replug into another USB port (Luckly I've got two on my laptop..)
I used the Vista drivers from TrintyGuides and bingo !
now I try and flash a WM6.....English or Italian...maybe French.
Thanks for the help I keep you posted.
Richard
It works
Now to discover the joys of WM6 after only having WM5 for two weeks....
/i am getting the same only rom update 3.14.4.1 now sees the phone..
has the device name changed???
evene exploit no longer sees the phone
sorry, can you be a little more clear.. what ROM are you flashing, and what exactly is happening?
by the way... i thought error 246 was the connection error... am i mixed up? which is 260?
This seems to be on any rom bar the Dopod roms
and it says 260 connection error
Error 260 connection error - the phone is not going in to bootloader mode - and the RUU cannot seem to initiate communication with the phone.
I'm getting this a lot recently trying to flash.
However, Hold the power and camera buttons while resetting with the stylus (keep them buttons held down).
When you get to the bootloader - plug the phone in - wait till you see the USB at the bottom of the bootloader screen - then run the RUU again - it WILL work - every time.
I used to get this error message alot. sometimes the programs you install don't allow you to update even if you force the phone into bootloader mode so you have to hardreset the device and then upgrade.....hope this helps
htc diamond stuck
T-Rob said:
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
Click to expand...
Click to collapse
hi ,
my htc diamond stack, no respond on the screen i try to do hard reset with tree buttons but its not working, nothing happaned, screen stay home screen with the time and not responding touching the screen at all
please emergensy help
I m having big troubles with my Universal. I m stuck in the Bootloader screen. When I try I hard reset (pressing 2 softkeys and reset and than 0 he says 'clearing now' for only one second and than switches back to the bootloader screen! I ve tried to upgrade it with MAUpgrade_NOID.exe. He than upgrades I think my OS only but after this a hard reset doesn t help! I keep getting stuck in the bootloader screen! I ve also tried a hard reset without the SIM and SD card but this don t help either......
Now what.......
have you tried set 14 0
I saw something like that. Can you explain how to a bit more specific?
sanderh said:
I saw something like that. Can you explain how to a bit more specific?
Click to expand...
Click to collapse
Hi,
Read this thread and follow the step by step instructions to reset your DOC Table.
http://forum.xda-developers.com/showpost.php?p=1097645&postcount=4
After completing the above please re-flash the Rom you wish to use.
When flashing Roms to your Uni, it is always best practice, to remove the SD Card and enter BootLoader mode before flashing.
Cheers,
Beasty
Try the little tool attached. It's from the wiki.
Here's how to use:
1. disconnect USB cable from your device
2. disable USB connection in ActiveSync
3. reconnect USB cable
4. wait some 30 seconds
5. run the tool
6. If successful, device will boot itself.
Has worked for me every time.
Psi
Had this issue today. Couldn't flash any rom and was stuck on the bootloader screen. Try flashing a shipped rom for your phone. That helped me. After flashing original I was able to flash WM6 rom using ROMUpgradeUt.exe.
Try a diferent cable.
If you get when connecting for a second usb, than changed i to the serial, try a diferent cable - its normal miniusb.
Then go to wiki and download UNI_ExitBootloader.exe.
Maybe will work.
If yes give a masage.
KR.
Lukasz
beast0898 said:
Hi,
Read this thread and follow the step by step instructions to reset your DOC Table.
http://forum.xda-developers.com/showpost.php?p=1097645&postcount=4
After completing the above please re-flash the Rom you wish to use.
When flashing Roms to your Uni, it is always best practice, to remove the SD Card and enter BootLoader mode before flashing.
Cheers,
Beasty
Click to expand...
Click to collapse
Thanks man, that really helped. My qtek9000 got stick at the bootloader's screen and i couldnt perform an upgrade. I followed ur instructions and now it is upgrading. waiting for the results.
thanks again
yeap, everything went fine.
Completely stuck without any UBS communication
Hi everybody,
Since i tried (yesterday) to flash a new UNIVERSAL 2.12 WWE ROM, i 'm stuck in Bootloader. I had this bloody Country ID error and after that, the USB connection between my Universal and my PC went wrong and ... i tried all the solutions given here and there :
1/ an exitboolader.exe tool
2/ the mtty option
3/ tried to kill all the process linked to AS in a way or another
4/ made several Hard Reset - connection - changing cable and so on ...
The main problem is that Windows XP is not able to recognize my Universal anymore SO ... i can't even try the solutions above based on an exiting commication thru USB between my PC and my PPC ...
I only have : "Serial" and "V1.0" on my pocket PC
Any idea to establish an USD relation between the universal and my PC ?
Pls help ... i missed this bloody device ;-/
Hello,
My HTC 3300 is blocked on Windows start screen.
I have hard reboot my device and un screen with 3 color appear.
When i plug my device with USB cable, my computer play a song to inform my device is well connected.
But when i launch Artemis USPL, a popup appear with the message : "No Device Connected : Would you like to try copying again ?" Yes, No, Cancel.
I'm blocked a this step.
Can you help me ?
Thx
PS: Sorry for my bad english. I'm french guy.
hi guys,
i have the same problem....
I was trying for the first time to upgrade my Artemis!!! I DIDN'T DO THAT!!!!
Please help me!
TNH
USPL only work if you are in WM. It doesn't work at the booloader.
Zecanilis said:
USPL only work if you are in WM. It doesn't work at the booloader.
Click to expand...
Click to collapse
yes... i know
i am reading.... i am looking for a solution.
I read on the POF USPL guide that probably (Unfortunately ) this problem should be caused by same PDAmobiz tool!!!!
i am being funny!!!
yet another bricked artemis owner
Hi…
Newbie as I am I’ll try to explain to you what you should do...I’ve bricked mine artemis()but I think it is more related to hardware issue. You should try this:
1. Download mtty
2. Disable usb in active sync
3. Bring your Artemis to boot loader(pres start record +start phone+ reset)
4. Start mtty, choose usb and you’ll get popup up screen with direct access to your device.
5. Type this in command line of mtty (NOTE-YOU MYST TYPE IT/NO COPY PASTE WORKS)
Password BsaD5SeoA
6. You’ll get %indicator bar on your phone and then you can switch off mtty(do not disconnect your phone!!!)
7. Just start your ROM upgrade (it has to be factory rom if your phone is locked) and you should be ok.
(You need to have downloaded your original factory rom...For me it was O2 UK...do not start until you have it all)
If it fails, or you get some error massages, repeat all from point 2. Or follow on screen instructions...recovery etc...
If it fails,repeat,repeat,repeat....
Hope it will help you and save you from reading s... load of threads!!
P.S.
I’m still trying to bring mine to life….
zikizile said:
Hi…
Newbie as I am I’ll try to explain to you what you should do...I’ve bricked mine artemis()but I think it is more related to hardware issue. You should try this:
1. Download mtty
2. Disable usb in active sync
3. Bring your Artemis to boot loader(pres start record +start phone+ reset)
4. Start mtty, choose usb and you’ll get popup up screen with direct access to your device.
5. Type this in command line of mtty (NOTE-YOU MYST TYPE IT/NO COPY PASTE WORKS)
Password BsaD5SeoA
6. You’ll get %indicator bar on your phone and then you can switch off mtty(do not disconnect your phone!!!)
7. Just start your ROM upgrade (it has to be factory rom if your phone is locked) and you should be ok.
(You need to have downloaded your original factory rom...For me it was O2 UK...do not start until you have it all)
If it fails, or you get some error massages, repeat all from point 2. Or follow on screen instructions...recovery etc...
If it fails,repeat,repeat,repeat....
Hope it will help you and save you from reading s... load of threads!!
P.S.
I’m still trying to bring mine to life….
Click to expand...
Click to collapse
It solved my problem: I've played around with some dll's on my Artemis and it won't boot anymore.
Just one thing: you must type password BsaD5SeoA, cause it's case sensitive.
THANK YOU VERY MUCH!!!
Hi guys,
i fixed my problem!!!!!
i flashed an official ROM (1.12.405) using a SD card (512mb)
now i'm going to work with ARTEMIS_USPL!!!! WOOOOWWWW
owner of a brick called artemis
glad it helped you solve problem...
when I was young I use to poke with programming...
but that was looooong time ago (remember zx spectrum?48 kb ram..haha)now you got it in your pocket(working if you're lucky guy, not like me)
Any way, point is:
never give up!!!!
Yes, I agree with you: NEVER GIVE UP!!!!
I'd like to help you, i'm not expert people on this work...
I just read a lot of good indications on this forum.
Good Luck
Thanks man,
I'm trying to find another motherboard,before I start playing with this one.
Maybe you know where to get one for artemis?(arte 200)Or someone with broken screen not willing to repair it?
cheers,
z
howdy, using a diamond with stock 1.93.479.3 WWE rom and am trying to install Olinex SPL and then a new rom, the problem is that I get [Error 202] when I try to install (using ROMUpdate Utility)... I read that to solve this issue I have to tick 'enable advanced network functionality', but as soon as I do, the activesync connection drops.
Anyways to work around this.. do I have to have 'enable advanced network functionality' ticked for the installation to work?
Cheers.
EDIT: forgot to mention I have windows mobile 6.1, and am using XP with service pack 3.
zdave said:
howdy, using a diamond with stock 1.93.479.3 WWE rom and am trying to install Olinex SPL and then a new rom, the problem is that I get [Error 202] when I try to install (using ROMUpdate Utility)... I read that to solve this issue I have to tick 'enable advanced network functionality', but as soon as I do, the activesync connection drops.
Anyways to work around this.. do I have to have 'enable advanced network functionality' ticked for the installation to work?
Cheers.
EDIT: forgot to mention I have windows mobile 6.1, and am using XP with service pack 3.
Click to expand...
Click to collapse
hi from what I can recall the activesnyc should drop, and the device into a multi couloured screen (bootloader) and then reconnect and the process begins
so what steps should I take exactly? enable advanced network functionality, then put it in bootloader and then sync it once more?
bump...nein?
bump..no one experienced the same?
zdave said:
bump..no one experienced the same?
Click to expand...
Click to collapse
Hello, Zdave!
Maybe I can help you to get into the boot screen multicolor ...
First, connect your phone to USB cable (be sure that the battery is over 50% energy), then using your stylus, reset the device, press and hold volume down key until the screen appears multicolored, should to show your type of connection, in seconds, "USB". Now go to where you installed the program and resume the installation ... I hope I was helpful ...
from my knoledge, the advanced network .... works on some computers (hardware) and doesn't on others.
You should try to enable this option, and use another pc.
hope this helps.
kokocf said:
Hello, Zdave!
Maybe I can help you to get into the boot screen multicolor ...
First, connect your phone to USB cable (be sure that the battery is over 50% energy), then using your stylus, reset the device, press and hold volume down key until the screen appears multicolored, should to show your type of connection, in seconds, "USB". Now go to where you installed the program and resume the installation ... I hope I was helpful ...
Click to expand...
Click to collapse
Activated bootloader, and hit the installation... but same thing, it wouldn't install. The screen, however, changed to a greyscale tint with a percentage... which is good, but It was still stuck at 0%..no movement on the PC as well (stuck at 0%).. then it goes to some recovery mode, which I skip because the phone starts normally (doesn't revert to the tricolour screen).
maybe there's a timed way to activate bootloader during the installation process? I've read most guides but maybe i'm missing something.. or my diamond/PC is messed?
zdave said:
Activated bootloader, and hit the installation... but same thing, it wouldn't install. The screen, however, changed to a greyscale tint with a percentage... which is good, but It was still stuck at 0%..no movement on the PC as well (stuck at 0%).. then it goes to some recovery mode, which I skip because the phone starts normally (doesn't revert to the tricolour screen).
maybe there's a timed way to activate bootloader during the installation process? I've read most guides but maybe i'm missing something.. or my diamond/PC is messed?
Click to expand...
Click to collapse
I do not know how I could help you , but bootloader immediately cancel the installation, where what you want to install is not intended for your device type, eg if for CDMA, or if for other model in addition to Diamond, I just happened when I wanted to put in mine, an operating system for Touch Pro... ,check again, if what you want to install is for your device.
God speed!
zdave said:
Activated bootloader, and hit the installation... but same thing, it wouldn't install. The screen, however, changed to a greyscale tint with a percentage... which is good, but It was still stuck at 0%..no movement on the PC as well (stuck at 0%).. then it goes to some recovery mode, which I skip because the phone starts normally (doesn't revert to the tricolour screen).
maybe there's a timed way to activate bootloader during the installation process? I've read most guides but maybe i'm missing something.. or my diamond/PC is messed?
Click to expand...
Click to collapse
Seems that u have to load a Hard-SPL.
Please Follow the Steps in:
http://forum.xda-developers.com/showthread.php?t=416211
or Use the search function.
Stuck @0% its a know issue without Hard-spl. Has nothing to do with ur a-sync problem...
mastah said:
Seems that u have to load a Hard-SPL.
Please Follow the Steps in:
http://forum.xda-developers.com/showthread.php?t=416211
or Use the search function.
Stuck @0% its a know issue without Hard-spl. Has nothing to do with ur a-sync problem...
Click to expand...
Click to collapse
used the search function thanks, but the whole point is that I'm trying to install the HardSPL (as stated in the original post). The installer mentions my current SPL and the one that is about to be installed (Olinex).
aww sorry, was late and seems taht i didnt read exactly..
tried to turn off Firewall? AV?
I never had probs with the option ticked on. But i think also without.
Have a look on the flashing method of HSPL, if i remind correctly u dont
have to put ur phone in Bootloader mode.
Instead it will load a sspl and reboot ur phone for flash HSPL. Then activesync
will loose connection and the RUU takes over.
Upgrade to Hard-SPL Olipro 1.20 - USB or SD Just Added SD Card Method at Bottom of this Post
10 Step Program
Pulled from Website dated: Monday August 06, 2007 by ??? if someone knows, I'll give credit.
Recovered and Updated Monday October 27, 2009 by SuperSport
because the WiKi has vanished
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Caution!!! Flashing Hard-SPL will Probably Hard Reset your device!!!! Backup all data FIRST!!!
Before you proceed, check which SPL is on your device:
*** Enter Tri Color Screen ***
--Unplug your phone from USB - Helps to avoid freezing USB Ports
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
*** Enter Tri Color Screen ***
If your SPL is 1.30.Olipro, 1.20.Olipro, or 9.99 CP, then you already have Hard-SPL on your device and can skip flashing HardSPL, although, I recommend using Olipro 1.20 to avoid problems.
If you want to continue flashing Olipro HardSPL 1.20:
Press the Reset Button using your Stylus. Wait for your phone to start back into Windows. Plug the USB Cable into your phone and PC. Verify ActiveSync or WMDC is connected properly. Now you can Flash.
1. Download "Olipro HardSPL 1.20.zip" in attachment below
2. Unzip the Files, and Run the Program "Olipro HardSPL 1.20.exe" This is a small AutoFlash file I created using Olipro 1.20
3. Windows Vista and Windows 7 may confirm you want to run the program. Choose YES.
4. Check the check box, click ‘Next’
5. Also Check this check box, click ‘Next’
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
7. After the version number has appeared, click 'Next'
8. In the following window, click ‘Next’, your phone may ask if it's ok to run the program, Tap 'Yes'.
(After you click this, the flash will begin, so do not disconnect your device or do anything on your computer)
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated. This will only take a moment.
10. Once your device is finished updating, if it did not automatically soft reset, Press the Reset Button with the Stylus. Click the ‘Finish’ button to exit the RUU program.
To confirm Hard-SPL is on your device, re-enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using USB Method!! Press the Reset Button with your Stylus to restart.
**********************************
Alternate SD Card Method
**********************************
For those who would rather use their SD Card for this (Maybe your USB Port is not functioning). For this method, the way I'm describing, your phone must be running a version of Windows Mobile. Can be any Version, 5-7. If your phone does not currently run, flash back the OEM ROM that came with it Originally. You can find some in my signature.
Caution!!! Flashing Hard-SPL may Hard Reset your device!!!! Backup all data FIRST!!!
1. Be sure you have a, Non-SDHC, SD Memory Card.
2. Be sure the card is formatted Fat32 and Without a Label.
3. Download the attached HardSPL SD.zip file and extract it's contents. Copy both files, SSPL-TRIN.exe and TRINIMG.nbh, to the Root of your SD Card.
4. On your phone, use File Explorer to browse to the Root of your SD Card.
5. Tap the SSPL-TRIN.exe file. This should run the file.
6. On some phones, you will see a security message come up. Select 'Yes' to run the program.
7. You should now see a Grey screen with Blue Lettering. It will be asking you to Press power button. Go ahead and press the power button.
8. You will see the update progress for a short moment, it will restart, and update again, then show "Update Complete - UPDATE SUCCESS" If you see this message, it has worked.
9. Press the Reset Button with your Stylus to Restart
10. Delete the two files from your SD Card (TRINIMG.nbh, SSPL_TRIN.exe). To confirm Hard-SPL is on your device, Enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using SD Method!! Press the Reset Button with your Stylus to restart.
Maybe if this could be Stickied?
Thanks, it's a very nice guide for Trinty users, clean and detailed, I also recommand using Olipro 1.20 and not 1.30 to avoid problems, especially with 6.5 roms the annoying "WLAN ERRROR" sometimes seen in bootloader mode ...
Yes, make this "Sticky"
Brds,
nAr
Thanks narshorn! Someone else posted this a long time ago on a WiKi I believe, and I just recovered what I could of the original web page and then rewrote it to work with my files. The original page was removed from it's server, so I grabbed as much of the cached version of it as I could, thus, I don't know who did the original.
Also, thank you for the confirmation of using Olipro 1.20 and not 1.30. That was my belief, and I've heard others, but I'm glad you confirmed.
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
update to 1.20 spl Olipro true sd card not USB
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
tzuki1 said:
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
Click to expand...
Click to collapse
Just added SD Method to bottom of post #1. Good Luck!
thongkh said:
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
Click to expand...
Click to collapse
Because stupid me forgot that if you don't have HardSPL on your phone, then TRI COLOR SCREEN flashing is not possible. Doh! FIXED above.
Thank you for bringing this to my attention. When I physically went through the steps, I forgot I still had HardSPL on my phone from previous.
I just went through the steps AGAIN after removing HardSPL, and verifed it works correctly as listed in Post #1.
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
thongkh said:
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
Click to expand...
Click to collapse
I've seen many reports that 1.30 caused issues. Olipro, 'the guy who made our Trinity's safe for Flashing', stopped updating the thread, but if you read it, you will find many users reporting problems and asking for the thread to be updated to go back to 1.20.
I've been using 1.20 since it was released, and have NEVER had a problem with it. And believe me, I Flash a LOT!!! I'm expecting my poor Trinity to catch fire any day now.
Oh... Thx for the tutor...that what i need now...
Good job someone remembered howto
Thanks for the reminder - managed to forget how to enter tri-colour screen in the three months since I last reflashed.
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
redoxy said:
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
Click to expand...
Click to collapse
Did you copy the TRINIMG.nbh file to your SD Card also? Was your SD Card formatted FAT32 and No Label?
Using the SD Method, you do not need to be connected to your Computer. Copy both files to SD and do all work from phone.
Let me know if that works or not.
Remove the HARDSPL...
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
sergiopedro said:
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
Click to expand...
Click to collapse
Only do this if you do not plan to flash any more Custom ROMs, and would like to stick with the OEM ROM (You may Brick your Phone if you flash from the Stock SPL):
Download the "HardSPL SD.zip " file from the first post.
Extract the files
Copy ONLY the "SSPL_TRIN.exe" file to your SD Card.
Run the "SSPL_TRIN.exe" file from your SD Card (This puts your phone into a special mode that will allow the HardSPL to be overwritten)
Now, your phone should be in bootloader mode with:
TRIN100
IPL_SSPL by Des
TRIN100
SPL_1.07.ds
At this point, you can flash your OEM ROM that includes the Original SPL and IPL.
I use this one: http://www.mediafire.com/?v5yjt1zvgjm
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
rcpamr said:
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
Click to expand...
Click to collapse
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
SuperSport said:
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
Click to expand...
Click to collapse
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
rcpamr said:
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
Click to expand...
Click to collapse
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
SuperSport said:
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
Click to expand...
Click to collapse
ok. thank u so much!