Encountered this yesterday with my BA.. The unit could not be turned on and I decided to do a reset. When I reset it, the unit would be stuck at the O2 logo screen and remain there forever..
Did a hard reset and then reinstalled my apps. After spending 4 hours on it, the unit refused to respond and I did a soft reset. After that, it got stuck at the boot screen again..
Just wondering if anyone had similar experiences with the BA and under these situations, is there anything that can be done to unfreeze the unit while still retaining the data in the machine? :roll:
Hi
try to upgrade ur rom ....
tell me what error u got!
Thanks
The ROM at that time was the latest version..there was no error..it was just stuck at the O2 screen..
Anyway..I did a hard reset and cleaned up the stuff that's not required..so far it seems quite stable. But i installed safemode as precaution..
Related
Hello,
I finally had the nerve to flash to Black 2.5 with the latest hard spl. The issue I have had is when I do a soft reset, I would see the AT&T logo and it would just sit there. Sometimes I would have to soft reset it multiple times before it shows the Black 2.5 Splash Screen.
Any ideas? Bad flash? should I reflash?
Thanks!
Umm.. i guess reflash, i don't have this problem.
Well actually i did. I would soft reset and it'd get stuck in the beginning so i'd soft reset again then in get stuck in bootloader mode. I was on the road and was panicking. So i unplugged the battery and plugged it back in and it'd go straight to bootloader. Did this several times and gave up. Got home ready to reflash my device but something came up, So i just plugged it into the charger, took care of my business, came back 25 min later (still in bootloader) soft reset and it was back to normal. So my problem was low power.
fone_fanatic said:
Umm.. i guess reflash, i don't have this problem.
Well actually i did. I would soft reset and it'd get stuck in the beginning so i'd soft reset again then in get stuck in bootloader mode. I was on the road and was panicking. So i unplugged the battery and plugged it back in and it'd go straight to bootloader. Did this several times and gave up. Got home ready to reflash my device but something came up, So i just plugged it into the charger, took care of my business, came back 25 min later (still in bootloader) soft reset and it was back to normal. So my problem was low power.
Click to expand...
Click to collapse
had the same problem several times: startup takes about 3 minutes and after that my device is incredibly slow...
softreset again (and again sometimes) and the problems are gone.
did a hard-reset en restore, but this issue occurred again a few times.
now installed LVSW (23-04-2007) for a while to see if it's ROM related (I think is is). but Black still is my favorite...
firebird2k said:
Hello,
I finally had the nerve to flash to Black 2.5 with the latest hard spl. The issue I have had is when I do a soft reset, I would see the AT&T logo and it would just sit there. Sometimes I would have to soft reset it multiple times before it shows the Black 2.5 Splash Screen.
Any ideas? Bad flash? should I reflash?
Thanks!
Click to expand...
Click to collapse
This can be caused by allsorts of things, most likely a 3rd party app causing problems on startup.
What have you got installed?
The only app I have installed the latest version of Dashboard from snoopsoft and iLauncher that might affect startup. However, I had those installed with previous WM6 releases with no apparent issues.
Hi!
I had a quit similar problem. It was gone after cleaning up the root of my microsd. After moving the stuff into folders this behavior disappear.
It looks like if there are a lot of files in the root, I have problems booting up, and I have to softreset several times till it comes back to normal. Just my experience....
hi everybody..
i've got a serious problem..
here's the story..
i was trying to upgrade to the touch v7 by mr. gullum.
after downgrading my prophet to the no vendor id rom, i upgraded my device to the touch v7.
next i tried to hard reset my prophet, realised that i can't do it cuz my camera button is not working.
went to a phone repair shop and fixed the button..the solder was..loose? i mean, the thing was unconnected from the pcb.
fixed it and tried to hard reset again.
black screen of hard reset appeared, but when i released the comm button, it went straight to the white screen showing os ver and ipl, spl ver.
tried to hard reset again and failed, it entered the white screen where we can restore rom dumps..i immediately pressed the comm button and camera button again..and it started formatting the bnfs..thing?
still can't do hard reset, tried to flash the no vendor id again, and this is the problem..i get stuck on 95% and after that it jumps to 100% straight away.
tried to flash gullum's touch v7 but i got the message that no device detected...tried pv 5.0.0.0.5b, pv 4.00.0.6, nanoscopic all with same result...
anyone can help?
oh maybe this will help:
when i tried to flash the no vendor id again, what shows up is this..(see attachment) the from image version is blank..
on the 95% where i get stuck, the progress bar on my device turns red as when it happens on the 80%.
thank you, everybody...
progress..
hi there,
it's not that usual mistake people make..i think i've screwed my hardware too..
now, my previous problem was unable to hard reset because my camera button was not working..the solder was loose..
i've soldered it and the problem was after every succesful attempt to flash 'no vendor id' rom, it resets and goes to bootloader screen again (tricolor screen)..
late last nite, i tried to hard reset after succesful flash of 'no vendor id' rom (after it resets and enters the bootloader screen)..i succeeded to get into the black screen of hard reset but when i released the comm button, it went straight into the htc white screen without me being able to press any button at all..
everything went well though, and it went to the 'tap screen to set up your device'..at this point i tried to flash the 'nanoscopic' rom (last rom i use before i messed up this phone)..it went well!
after succesful attempt, i tried to hard reset again (no luck again), but after the htc screen shows up, the nanoscopic splash screen appeared!!!
whew, i thought i had my phone fixed already, but when i did a clear storage, it resets and enters into bootloader screen again! i tried soft reset via software and via manual way, and it enters the bootloader screen everytime!
now, i've fiddled some more and i now realise that just by pressing the comm button and doing soft reset can make me go into the bootloader screen..i'm guessing that the technician at the phone shop soldered wrongly...and now my comm button works as camera button too..
i think he accidentaly soldered some other button too to the comm button and that's why i always get into the htc white screen after i release the comm button in the black screen of hard reset..
i'm going to go back to the shop again after work today, but i'm still confused about the way my device enters bootloader after every reset (hard reset and soft reset)..
a friend gave an opinion that maybe, like in desktop, (there's the bios then there's the operating system), the 'bios' of my device is ****ed up?
any help greatly appreciated!
Dear all,
I need help in repairing my Asus p525. I was trying to flash it to WM 6.1, but suddenly update failed. After that i started getting asus Blue Screen, and nothing more. I cannot hard reset, neither turn on the PDA. When I take out the battery, I can, by pressing CAM REC JOY and SOFT RESET button to get to USB loader.
I used USB loader and reinstalled my ROM and Boot Loader to Official Release of Asus. But this didnt help and I still get only Blue Screen, and after that nothing - unless I take out my battery for a while and return it.
Can anyone help me with this problem ?!
Greetings
New thing
Last night I took my battery out of the phone. Today I dont even have ASUS BLue Screen, but still i can, while holding the buttons, on reset (inserting the battery) to go into FORCE MODE.
Anyone know what to do ??
Today I reflashed with new roms, but it just dont work.
Greetings
I realised now, that when I charge the battery FULL, the phone starts working ?! First i have problem to calibrate the screen, and later on the OS start to work, and everything seems fine ?! But it resets, block..... hardware thing ?
Hi guys,
my diamond has gone berzerk!
it gave up on me all of a sudden....froze so i tried to restart and didnt work. i did a hard reset and eventually finished. the problem is that the phone wont detect any network, wifi and bluetooth are working but the 'phone' isnt - in comm manager enabling phone appears to do something showing the busy icon but then reverts back to 'off'.
im using hard spl 1.40
radio .25.08
and every rom does this.
the red reset button is also not doing anything more, i.e pressing it does nothing...
ideas???
oh and it occasionally resets too....
did a hard reset and the phone keeps rebooting....gets to the windows logon and then reboots....
anyone??
flash a stock rom fron bootloader mode it worked for me
simba2585 said:
did a hard reset and the phone keeps rebooting....gets to the windows logon and then reboots....
anyone??
Click to expand...
Click to collapse
how much?
after hard reset two time could be normal.
it restarts an infinite number of times - as if it gets stuck in some loop.
its very random so there can be periods of time where its fine and i think its cured itself then all of a sudden it will restart and be fine for a while then sometimes it can just get stuck in a restart loop.
have you find a solution?
i know from my experimentals that loopings are normal by ****ti-mitti-roms.
the rom could be fine, but one deleting file here or there let starts the looping.
try orig. rom from your device. if looping again ... dont know :-(
Maybe this thread can help you out, it's worth trying:
http://forum.xda-developers.com/showthread.php?p=3433851
hi i have the darkvisions 5.0 rom and i have changed my splash screens and that all worked perfectly fine but about a week on and when i installed something from my pc my phone froze so then a did a soft reset, then the usaul red writing come up then it just freezes and i have left it overnight to load but nothing happens does anyone have a solution. and sorry if this has already been posted if so can u direct me becuase i could not find anything, and sorry if it in the wrong place
Take battery out for a few minutes then restart. A soft reset isn't the same as a cold start. You nee to clear the ram.
Then if it still gets stuck, reflash, but flash a stock rom first....
Cheers...