Stuck On 95% And Can't Upgrade/downgrade - Upgrading, Modifying and Unlocking

hi everybody..
i've got a serious problem..
here's the story..
i was trying to upgrade to the touch v7 by mr. gullum.
after downgrading my prophet to the no vendor id rom, i upgraded my device to the touch v7.
next i tried to hard reset my prophet, realised that i can't do it cuz my camera button is not working.
went to a phone repair shop and fixed the button..the solder was..loose? i mean, the thing was unconnected from the pcb.
fixed it and tried to hard reset again.
black screen of hard reset appeared, but when i released the comm button, it went straight to the white screen showing os ver and ipl, spl ver.
tried to hard reset again and failed, it entered the white screen where we can restore rom dumps..i immediately pressed the comm button and camera button again..and it started formatting the bnfs..thing?
still can't do hard reset, tried to flash the no vendor id again, and this is the problem..i get stuck on 95% and after that it jumps to 100% straight away.
tried to flash gullum's touch v7 but i got the message that no device detected...tried pv 5.0.0.0.5b, pv 4.00.0.6, nanoscopic all with same result...
anyone can help?
oh maybe this will help:
when i tried to flash the no vendor id again, what shows up is this..(see attachment) the from image version is blank..
on the 95% where i get stuck, the progress bar on my device turns red as when it happens on the 80%.
thank you, everybody...

progress..
hi there,
it's not that usual mistake people make..i think i've screwed my hardware too..
now, my previous problem was unable to hard reset because my camera button was not working..the solder was loose..
i've soldered it and the problem was after every succesful attempt to flash 'no vendor id' rom, it resets and goes to bootloader screen again (tricolor screen)..
late last nite, i tried to hard reset after succesful flash of 'no vendor id' rom (after it resets and enters the bootloader screen)..i succeeded to get into the black screen of hard reset but when i released the comm button, it went straight into the htc white screen without me being able to press any button at all..
everything went well though, and it went to the 'tap screen to set up your device'..at this point i tried to flash the 'nanoscopic' rom (last rom i use before i messed up this phone)..it went well!
after succesful attempt, i tried to hard reset again (no luck again), but after the htc screen shows up, the nanoscopic splash screen appeared!!!
whew, i thought i had my phone fixed already, but when i did a clear storage, it resets and enters into bootloader screen again! i tried soft reset via software and via manual way, and it enters the bootloader screen everytime!
now, i've fiddled some more and i now realise that just by pressing the comm button and doing soft reset can make me go into the bootloader screen..i'm guessing that the technician at the phone shop soldered wrongly...and now my comm button works as camera button too..
i think he accidentaly soldered some other button too to the comm button and that's why i always get into the htc white screen after i release the comm button in the black screen of hard reset..
i'm going to go back to the shop again after work today, but i'm still confused about the way my device enters bootloader after every reset (hard reset and soft reset)..
a friend gave an opinion that maybe, like in desktop, (there's the bios then there's the operating system), the 'bios' of my device is ****ed up?
any help greatly appreciated!

Related

P525 - Upgraded to WM6.1 and BRICKED?!

Dear all,
I need help in repairing my Asus p525. I was trying to flash it to WM 6.1, but suddenly update failed. After that i started getting asus Blue Screen, and nothing more. I cannot hard reset, neither turn on the PDA. When I take out the battery, I can, by pressing CAM REC JOY and SOFT RESET button to get to USB loader.
I used USB loader and reinstalled my ROM and Boot Loader to Official Release of Asus. But this didnt help and I still get only Blue Screen, and after that nothing - unless I take out my battery for a while and return it.
Can anyone help me with this problem ?!
Greetings
New thing
Last night I took my battery out of the phone. Today I dont even have ASUS BLue Screen, but still i can, while holding the buttons, on reset (inserting the battery) to go into FORCE MODE.
Anyone know what to do ??
Today I reflashed with new roms, but it just dont work.
Greetings
I realised now, that when I charge the battery FULL, the phone starts working ?! First i have problem to calibrate the screen, and later on the OS start to work, and everything seems fine ?! But it resets, block..... hardware thing ?

Load issue

FIXED NOW!
Need help.
I burned the new Kavana ROM. everything was working ok.
placed my microSD and the device didn't recognize it, so i rebooted.
upon reboot the device got stuck on the white HTC screen.
pulled battery
tried again, rebooted, past the HTC screen to the Windows Mobile welcome screen but freeze again. hard reboot didn't respond.
pulled battery, then turned back on. device didn't even turn on!
tried several times with/without battery hooked up to power , and with/without SIM and/or microSD (all possible combinations) and nothing.
had lunch
went back to it and the device magically booted it but after the white HTC screen i got a blue screen asking about error from last reboot. said yes to correct. rebooted went past white HTC and into Windows mobile welcome screen and froze again.
repeated the process several times and finally got to the blue screen again asking about error from last boot, this time said 'no' and device continued boot in a white screen without HTC logo and froze.
all hard reset attempts were unsuccessful (if i'm doing it right: hold two soft keys and then power button).
now the device boots to the white HTC screen and then is stuck.
what to do?
edit: got the hard reset to work and reconfigured my phone. i only noticed the black screen for a split second because my Dash has issue that it thinks that the green send button is being pressed all the time (anyone know how to fix that?).
Thanks
Find your original rom in sticky, go into bootloader and flash original rom, then flash to wm6.1.
have the same issue!!... did you fixed? the main problem is activesync is not running so how do i install another ROM?
Active sync doesnt have to be working aslong as u got ur s621 pluged in and u wait for a few seconds before starting the ROM it will work.

A nightmare with my i780...

Hi,
It's just like a nightmare...
My i780 had been bricked.
However, there is no problem to flash any rom,and no error occurs.
But, since I have to take a Hardware Reset after flashing, the nightmare starts...
It is frozen after I press "space" to have a hw reset! Nothing changed even after 1 hour!
Then I try to power it up, but it only shows the Samsung logo.
And it's more surprising that when I charge up. The red led shows up, and the screen shows that
"Formatting
Please wait just for a while"
It will never disappear.
So, ...anybody have ideas?
Whatever rom I flashed, it's successful, but fails to reset.
I think, since I can't apply a hw rest after flashing image, the image won't really be flashed. And it seems the hw reset trap into an endless loop. Now what should I do?
BTW, I found that there is someone similar to mine...
Just like http://forum.xda-developers.com/showthread.php?t=479819
Help! Help me out of the nightmare...

Diamond held on startup cant install hardspl or anyother ROM

2 days ago i was playing with my touch diamond and it held when i switched on WIFI (wifi was working fone for a year now). When i rebooted the phone froze at the screen where Touch Diamond is written and at bottom right some info regarding ROM/Radio/SPL etc (R 1.09.25.23 G 52.51.25.26H D 2.03.00.00).
Tried many times but couldn't boot it . Just when i was about to get hopeless it started booting if i hold volume down, enter and press reset pin on the screen still taking too long. As i had stock HTC ROM so i upgraded it to the latest to see if it solves the problem. After upgrade phone would still boot randomly by trying the Reset pin and the mentioned button but after a few trys that also stopped working.
Now the phone is stuck on the same black screen, i can only resintall the latest Rom and All the way mentioned on the forums dont work for me i have tried signed unsiged soft and hard spl or direct Custom ROM upgrades but nothing goes beyond 0 %.
All the SPL upgrade articles require to copy jump spl. exe to the phone but i can do that as i am unable to create a Active Sync relationship (Eventhough i have tried upgrade by manually going into the tri color screen by holding volume down button while booting it).
The Hard Reset option allows me to hard reset but has no effect on the phone's condition.
anybody who could help me out here?

Rebooted Touch Diamond and the circle LED was lit up solid. Any ideas?

Greetings All,
I had a very interesting problem happen to me and I would like to know if anyone else has experienced the problem before and what it could mean.
I went to restart my phone to boot into Android using GenY Dual Boot but after I had pressed the reset button the phone hung with a black screen and my LED circle constantly lit. Tried rebooting again and the phone did not want to know me however the circle went back to normal, it would get to the Touch Diamond screen where it will show you the ROM&Radio version on the bottom left and as soon as it got past that it would reboot and start the process again.
So I went and did a hard reset and still the phone would not boot. In the end doing a mtty flash, then a hard reset brought the phone back to life but now I am worried that there might be a underlying issue at play.
So my questions are:
What would cause the white ring to stay on?
Cause the phone to get stuck in a constant reboot?
Is there a problem with my phone that I need to get looked at?
Using the latest GenY D2X ROM with the HardSPL 1.93 and the radio 1.17. Just did a restart now and all is fine. Maybe it was a once off problem?
Thanks for any info .
/btw not sure what to search for hence the reason why i created a new thread.

Categories

Resources