Related
Hi, this is the 1st time for me, so please help me if you can.
I have i-mate PDA2K was working good, and once I wanted to put some programs like every time and suddenly the mobile turned to black screen with this word 'serial' and when I connect it with PC gives me 'USB'.
and when I tried to reinstall the WM2003 again it gives me error 120
country ID error and gave me this:
The ROM image that you are trying to use is not designed to work with your device. Please check the vender Web and dounload the correct ROM update.
then I tried to install WM2005 and it was accepted but the problem is:
I can't use green and red buttons and I can't use the mobile.
Also I can't format the device even with pressing (Power + camera + record + soft rest).
so, please if any one has Idea give it to me
thank you.
read wiki, just click on my signature
or just press reset button with stilus
I have just updated to WM 2005 and get this message Device Authentication failure. Please Contact the product manufacturer, please provide your device ID 0062667000.... how can i get my phone working again. Can someone please provide me with detailed in struction PLEASE
I have an Imate Pocket PC Phone Edition, i hope that helps. I only have a 1 gig Sd card and the Imate Disk that come with the phone to help me.
Pls visit buzzdev.net and doenload a better ROM for yr handset and reflash yr device...
Fixing my Imate help still needed PLEASE
How do i flash this thing of mine, i have an imate pocket pc phone edition, i am new to all of this which rom do i get i dont have active sync as the phone just boots to Device authentication failure and wont go any futher than that, how do i get information between the computer and the Imate,
thanks for your help
Sam
(yep another dumb blonde) :?
Re: Fixing my Imate help still needed PLEASE
marsam said:
How do i flash this thing of mine, i have an imate pocket pc phone edition, i am new to all of this which rom do i get i dont have active sync as the phone just boots to Device authentication failure and wont go any futher than that, how do i get information between the computer and the Imate,
thanks for your help
Sam
(yep another dumb blonde) :?
Click to expand...
Click to collapse
You generally need to put it into the bootloader to flash it again if you can't active sync. If you check the wiki you should be able to find your device type and instructions for booting it into the boot loader. Once you've got that done simply plug in the USB cable, wait for your PC to tell you your device is ready, then run the ROM installer.
Dear All !! Dear Pof!
I am trying to unlock hTC S620 ,but with no luck!!
when i connect the phone with Active Sync with the softwear and press AUTO_Unlock_v3a it showing me direct the message :
SoftSPL error
Erorr
Insufficient trustlevel.
You need to application unlock your device (or singn executable with privileged cert)
even i did try to past the file SSPL in phone and open it ,it gona say to me the same erorr !!
Please what is this problem is ?
and another think :how can i make hardwear Reset to this model hTC S620? ther is no hole place to press For reset ,could u show me please how to do it .
i am very sad becouse i spend over 5 hours trying to unlock this funny phone!!!
please help!!
Thanks.
Exclusive Windows Mobile 6.1 ( WM6.1 ) English for HP IPAQ rx1950
Done by Victory144 & Guifort
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Tested and all work very well....
Downland:
RAPIDSHARE
MEGAUPLOAD
FREE (FRENCH)
Mirros by Guifort...
See YouTube Short Demonstration Video
See YouTube Long Demonstration Video *Best Quality*
Windwos Mobile 6.1 For Ipaq rx1950 KITCHEN (For Devolopers and Advanced Users Only)
Download. MediaFire
Windows XP only.
1. Connect you Device To PC "USB CONNECTION" with Microsoft ActivSync Installed...
2. Follow the instruction .. (May appear some device notification to
allow recognize of the device correctly and changes to flash mode etc " You Must Always Click Accept" or you will not be able to flash your device)
3. Run "hpRUU" tools to and follow the instruction.
If the program can not flash for some reason, try to put your device in "Flash Mode" Manually by pressing "Contact + Email + Reset together" and try again.
4. When the process finish ..The device will restart automatically.
5. When the boot loader is loading Make HARD RESET ( By Holding " CALENDAR + WIRELESS + Reset " For 3 Second !
6. Wait to re boot... "it may take about 2 or 3 Minute for the First time" ....
7. Calibrate the screen as Usually ..
8. Now go to " Start / Programs / Address Book " Run that Allow the two files needed ( By Accepting the notification Bellow)
9. In the same program go to "Menu /Option" And In the first tap "General" Mark this options :
Set as default contact manager
Assign on hardware button
10. Then Press OK ... Exit the program
11. Soft Reset...
12. Accept the notification about the WIFI program ! Then will appear in the Today menu the WIFI Icon where you can Power On /Off the wireless ....(As the default "Hp Wireless manager" dose not work properly).
Done!
Optional you can install the office cap as usually ! included ...
Click to expand...
Click to collapse
Great job - it's wonderful -so far just one minor problem. Task manager is still in Russian in "programs". UC and .NETCF 3.5 would make it even better.....
Thanks ...
The task manager can be changed from File Explorer / root / Windwos/Start Menu/programs/ then Select that Rename to Task Manager .. Its Done !
NETCF 3.5 i cant cuz theres no more space to add any thing on the rom as it 32 MB !
Problems
I run the hpRUU at one time it says Unknown Device. What should i do?
Very Nice!!
I've used this rom for a couple of weeks now and so far only one problem, the wireless connection fails to reconnect after the power is turned off. I have figured out a way to circumvent this problem. Uninstall the WifiIO and use the wireless button as you would in WM5, but before it disconnects pick the view wireless networks link and press Menu -> Turn Wireless On. What a PIA, but the faster operating system definately makes up for it. Thanks a bunch Victory!
2 "rubarht123" You are welcome ! Thanks for the tip .. Can you be more clearly about yuor setting ?
2 ".bin" Make sure youve Microsoft Active Sync installed and the Ipaq connected to it ! Then try !.....Good Luck ...
Rom for Ipaq h5550?
I hope I am not committing some sort of faux pas by asking this, but what would you charge for a WM6.1 rom for an Ipaq h5550? I could supply a machine for testing.
I am dead serious about this and am willing to pay. Please advise.
Thanks!
Re: Settings
I'm not sure what you mean by settings, but the wm5 normal button for wifi is rendered useless under wm6.1...you have to use wifiIO for some reason. I have sktools free version installed and could have deleted reg setting don't know though. Reinstall wifiIO and still disconnects after power. I've looked in windows dir. for wifion.exe but only find wifioff. Prefer wm5 button to wifiIO, wish there was a way to get it working again. Thanks.
6.1 installation
Hi,
I downloaded the software thanks btw
extracted files
connected pda with activesync
launched hpRUU.exe
followed on screen instructions
watched progress on pda
I now have an error wrong image on pda when i try to reset.
tried relauncing exe but i have no comms to pda from pc.
Help please!
Hello
Your pda can't boot ? you can reflash it with the SD Card method if you have make a backup.
2 "BTE72"
Please see this thread : http://forum.xda-developers.com/showthread.php?t=509976
hello,
tis pot sounds awesome. i downlaoded ur file. started to patch. that flasher recognize my ipaq. i then continue but my screen freezes at HP INVENT white screen u know. nothing happens. i can reset and turn back to my ipaq wm5 but why i cant do a flash? thanx.
i think a video will be awesome.can u do it pls? thanx.
2 "mrbigtime"
Maybe if you Hard Reset that first, will work ! Do not forget to backup your data !
If not you can try to put the pocekt in FLASH MODE ..i do not remember the correct combination :
1:
HOLD TOGETHER Calender + Wireless + RESET For 5 SEC more or less
HOLD TOGETHER COntacts + E-Mail + RESET For 5 SEC more or less
One for Hard Reset and the other for FLASH MODE .....
Also if dose not work, you can upgrade the (Boot Loader) first then try ...
http://forum.xda-developers.com/showthread.php?t=509976
Ill try if i can found a camera to make the video ....But Just Demonstration not Tutorial to install .... As i do not have a time for that ....
Good Luck....
NICE ROM! but sdhc is not working for me
This rom works fine, but my sd card is not being recognized
I would like to know if anyone has come into the same problem an found a solution.
Have a Sandisk 4gb SDHC card. If you install drivers in rx1950 wm5 version it will work flawlessly.
I thought wm6.1 would recognize it without patched drivers but no luck, and all drivers installation process end with "unsuccesful" message.
please, is there a solution?
victory144 said:
2 "mrbigtime"
Maybe if you Hard Reset that first, will work ! Do not forget to backup your data !
If not you can try to put the pocekt in FLASH MODE ..i do not remember the correct combination :
1:
HOLD TOGETHER Calender + Wireless + RESET For 5 SEC more or less
HOLD TOGETHER COntacts + E-Mail + RESET For 5 SEC more or less
One for Hard Reset and the other for FLASH MODE .....
Also if dose not work, you can upgrade the (Boot Loader) first then try ...
http://forum.xda-developers.com/showthread.php?t=509976
Ill try if i can found a camera to make the video ....But Just Demonstration not Tutorial to install .... As i do not have a time for that ....
Good Luck....
Click to expand...
Click to collapse
Thank you very much.but sadyly nothing works and my PDA is already uptodate...very interesting
and mostly when i try to flash it says HP ROM UPDATE(or what ever it is) STOPPED WORKING message appears. iam not ven sure if it works or not
I ran the hpRUU, but after it restarted, now it won't turn on and I can't do a soft reboot or hard reboot. I've tried everything I can think of and I don't know what else to do. Any suggestions?
mabe you already tried this...removing the battery. wait some seconds, put it back again.
it has worked for me when my ipaq rx1950 doesnt starts. Dont know why it happens but it has made the trick when it doesnt turns on.
if that works, remember to hard reset the device or it will not pass from boot screen.
I tried taking the battery out and leaving it for a few seconds, but that didn't help either. It's almost like all of the buttons are not responding anymore.
2 "sdwestbroek"
Make sure you've the battery charged ...
then remove the battery for about 2 to 5 minutes ....Then plug the battery again ... and the pocket must turn on automatically ! just wait about 4 to 10 sec....
Hope this help .. i and the same problem ..and solved with this method ....
2 "mrbigtime"
Try to download the file again .. from another host ... and then try ... Thats maybe solve the problem ..Other thing you must be in Windows xp and disabled the Anti-Virus ..ect ....Thats may solve your problem....
Good Luck for all....
WM6.1 Works excellent but the only thing is that he does not reconize my TomTom antenna anymore?
why not ?
Hello i have problem changing my ROM to the original ROM... My phone is Dopod 838 Pro, now my ROM is "GoldenGlobe_Black_WWE_V10"... for me its not stable... there are times it freeze up... Now I downloaded the orginal ROM from the HTC website. I fallow the instruction from the site, when i reach the part bootloader, after a few seconds I get this messege.. "ERROR [260] : UPDATE ERROR".... Please help whats happening with my phone...
NOTE:
I do apologies if this problem is common. if theres a solution please guide were to find, or if you know how, it would be nice if you'll provide it... thanks...
This is the messege:!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
if you like not to bite you to fix it via a memory card. changes you ruu_signed.nbh to HERMIMG.nbh. you know how he is and not as you write here. turn off the phone. and to enter bootloader using the buttons on the left side of the phone and right side. written on the keys is ok and the second is a button-down / power key. the two buttons pressed and the current bootloader does not start. when to place. so sorry. Sorry but my English is poor
It seems that you're using Vista or windows 7. Try to find a windows XP computer and up that rom again.
Some ports are opened!
Lemme xplain this... osmetimes the drivers of our pcs gets closed and opened constantly in some proceses and in the upgrade it happends so... softreset your device it must go to bootloader reconect your phone and try again... if not works...
Do the upgrade via SD: as the guy upper tell you change the nbh name as he says and copy the file to your CLEAN!!! micro SD 1-2 Gygas it doesnt works in MicroSD bigger than 2Gygas ok? insert the SD and reenter to Bootloader it beguns to upgrade... be sure your batt has enough charge... more than 50% MORE than that! i suggest.
Mine does the exact same thing everytime, on Windows XP, here is what I do now.
Run it, and when the phone gets to the red, white, green, etc screen, and says USB across the bottom, unplug the USB cable, and plug it back in, this works everytime for me.
it is easier and a lot safer to use sd card flash
thanks...
i'll try all of your suggestions... if nothing happens , hopefully not... what ROM is stable? ROM does not freezes up... thank you and have a good day.
nothing
I tried the SD card upgarding... after updating it froze up welcome part.... nothing happens... by the after the Updating Complete what will I do?
redo the same thing but first.... upgrade the stripped original att
wait till the bar reach 100% and start boots... then unplug the sd card...
perform a hardreset let it boot... the upgrade again with sd card wichever rom you want and unplug the sd card when the bar reach 100% and start boots... then when it is in welcome splash image... perform hardreset!!!
I will write this f·$"n leyend in my siggy!!!!!
helloo..
How do i do the upgarde stripped original att? and were can DL the file... and can i do using SD upgrade..
almost all the chefs (include me) we have at first post of our roms thread a link to it... just DL it unpackit rename it... and copy it to the sd inserted and follow the steps... i told you! oh if mine doesnt works, try yours... seems that works fine
oh charge your battery dude.
worst thing happened...
worst things happened... please help....
-After doing an SD card upgrade in bootloader screen using the original ROM from HTC.com:
Status of my Dopod 838 Pro:
Stuck at the Welcome Screen that says "Windows Mobile"..
- I tried to do a SD upgrade at the bootloader again I get a messege 028002
"not allow", it returns to boot loader...
- I tried doing a bootloader updating using my PC... I only 1% then shut the phone down
- Please help me... I cant use my phone anymore... please help... thanks...
By the way the bootloader says
HERM100
IPL-1.04
HERM100
SPL-2.03
Maybe this can help the situation.... thanks...
on vista/7 right click go to properties and copatability try putting it into windows xp mode and give it admin rights ..
if that don't work try putting the phone in bootloader mode then connect to ur computer and try flashing a rom this way..
good luck
raymondht said:
worst things happened... please help....
- I tried doing a bootloader updating using my PC... I only 1% then shut the phone down
- Please help me... I cant use my phone anymore... please help... thanks...
By the way the bootloader says
HERM100
IPL-1.04
HERM100
SPL-2.03
Maybe this can help the situation.... thanks...
Click to expand...
Click to collapse
NO WAY!!!!!!
You are not hardspled!!!!! what happend Tho you have unlocked your device!!!
Man how could you upgrade the SPL in that way!!!!!!??????
I think that your phone goes off because you dont have enough battery to upgrade.... or maybe its just that the SPL is not unlocked!!!
Man this is serious!
you need an XP you need your battery fully charged
try to get a new USB cable... and try to get a ROM that match to your Carrier and country... this is no good... check the Siganture of CRCinAU he has a repository of shipped original ROM.
waaaahhhh....
I basically download the ROM version from www.HTC.com... Here's the direct site of the download:
"http://www.htc.com/sea/SupportDownload.aspx?p_id=37&cat=2&dl_id=197"
ROM info:
Release Date:07/21/06
ROM Version:1.23.707.4
RF Module Version:1.06.00.10
Protocol Version:32.37.7010.01H
-----------------------------------------------------------
what is repository shipped...?
what are the steps I need to do fix the issue.?
do we need everything for that guys? hahaha well i think we must to help
go here http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
or here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
search for your carrier and or language that match to your country...
and try to upgrade with the activesync!! not SD
Once you get it... enter to Bootloader and start the upgrade... make it on XP!!!! nad with many batt!!!... unplug your sd card and the sim too (dont think its fine but for prevent issues.)
how could you do it without hardspl!!! thats because of not read... and do things without ask.
hi
How would I know if i'm downloading the right ROM?
I'm from the philippines
at the back of unit says:
HERM100
FCC ID: NM8HERM100
DOPOD 838 Pro
IMEI: 355714011259410
S/N: HT726F203694
P/N: 99HC8032-00
"how could you do it without hardspl!!! thats because of not read... and do things without ask. "
I just want to QUOTE this.... I always tried doing HardSPL before I change my ROM, I'm not dumb okay... but it disconnect my PC from my phone... and correction sir I can READ... no need to remind me... Thanks by the way for your HELP...
Jajaja so
if you do the HardSPL...
HERM100
IPL-1.04
HERM100
SPL-2.03
Click to expand...
Click to collapse
No you didnt...
Well the PC gets an error so... why try to upgrade instead of try again the hardspl?
in fact is not the problem here who has the true or who cant read...
the important thing here is to know how you fon can be restored by the original shipped rom for dopod
so
try then one by one
we only need that the rom boots!!! to apply the hardspl.
sorry...
Sorry about the previous aligations regarding "reading"... I was so frustrated that time, bec my phone broken.... I do Apologies!... By the way sir just addup I saw a "No GSM" on startup... Thank you and have a great day..