Related
I tried to do a hard reset and the black screen came up and when i pressed the green button it tried to format the jamin but then came up with format failed
I then managed to get the device in bootloader mode by camera + reset
then let go of reset and press power once and that got me in bootloader mode, I then tried to install the new rom again and went to 86% and said error [326] This NBF can not be used with your PDA phone. Please check your NBF file. I than took the battery out of the imate device and when put it back in the phone wont even load of anymore its just black and dead. I know it isn't the battery because before I tried the hard reset I charged up the battery to full and i know there is definately nothing on the screen its black and when trying to plug it in via usb can not estqablish connection no more. I feel that this was a hardware issue from the start and is there anything else which i coulld try to prove otherwise? or do i need to send back to service centre? all help much appreciated
i mate jamin went dead
please please help me i was trying to unlock my friends imate jamin pm300 and it went dead, i think i used the wrong software to unlock it, i was using the 12mb antenea unlocker then after i take a back up of the rom in the phone it modify it and then when i try to restore it is gives me an error message about my laptop battrey is not 50% but is is 100% the i switched off the handset and when i try to power it on there is notting. what can i do please please help me my e-mail address is [email protected]
Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights
Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?
i have the same problem
is there anybody for help???
SOS please
Eenigmaa said:
Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?
Click to expand...
Click to collapse
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.
fingerstoo said:
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.
Click to expand...
Click to collapse
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....
Eenigmaa said:
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....
Click to expand...
Click to collapse
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message
vladtapes said:
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message
Click to expand...
Click to collapse
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
You should close process "wcescomm.exe" on PC in task manager. Then hold button record, power and puch reset after that you will come in boot loader. Run the program mtty.1.42 and select usb connect. If You will see the any error just start again mtty. Put command l c:\os_213u.nbf (You should put correct flash file in c:\ or use correct path to os_213u.nbf, l - like L but small). When it will done You should start PocketLOOX5xxFlashTool.exe and flash you PDA.
Click to expand...
Click to collapse
Eenigmaa said:
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
Click to expand...
Click to collapse
do you confirm the method is fully functional?
I made a backup of my german original rom, if i have problems i want to restore it...
have you got a backup of your old wm5?
thanks
Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!
Eenigmaa said:
Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!
Click to expand...
Click to collapse
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...
vladtapes said:
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...
Click to expand...
Click to collapse
You can if you use an translator like www.windowslivetranslator.com or translate.google.com
then it is pretty easy.
I've resolved...
Fully functional WM6.0 newplowe in English...
now I'm searching for editing it in Italian/French but I need to edit the rom part of the XIP (just that).
For doing that, I need to open decrypt the file .nbh file (don't really know howto, and newplow doesn't answer about that... ).
Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks
rcretu said:
Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks
Click to expand...
Click to collapse
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.
N560 - still stucked in the climbers bagground after WM 6.1 flash
fingerstoo said:
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.
Click to expand...
Click to collapse
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...
rcretu said:
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...
Click to expand...
Click to collapse
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...
rcretu said:
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...
Click to expand...
Click to collapse
PHEW! Thank goodness. I suspect you did not do the hard reset correctly at first. But I agree about the Loox being precious! I look after mine very carefully! Glad I could help you. My pleasure....
My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!
vladtapes said:
My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!
Click to expand...
Click to collapse
I think you have received a reply from Newplow on his guestbook....
Hi
I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP!!
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
I've done already procedure You've mentioned here with taking of the battery for at least 30 secs with hard reset afterwards but it is still climibing screen. Can U manage this as well???
THX
The most common error with the procedure is NOT making a proper or true hard reset, or back to factory settings reset. If you do it wrong, you will only achieve a soft reset, the same as you get if you just put the stylus in the reset hole in the base of the N560.
The correct procedure is to hold Power/Resume/Suspend button (on/off button) and the Calendar button simultaneously. Keep holding them and with the other hand press in the reset hole with the stylus. The screen should blank out. KEEP holding the other two buttons all this time, and release the stylus. KEEP holding those two buttons until the screen display returns, only then release them.
This should allow another burn.
I hope this is the problem. It has happened to me and others, so I think I am right. But if this fails, you may need another approach.
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..
...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?
I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get
hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work
...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn
Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p
ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000