XDA simunlock help - Upgrading, Modifying and Unlocking

Hi
I tried to unlock my O2 XDA2. It seems that I have finished the job. But I cannot come back to the window home page. It remains in serial page in boot loader mode. How can I go back the home page?
Thanks

Try a soft reset.

Related

Help me pleased!! My new XDA II is dead

Hello!
The screen on my XDA went black and phone botons are always ligth. It won't switch on.
I have tried a soft reset and removing the battery but XPA II no work.
Can anyone help?
can u put it in bootloader mode by pressing power+camera+action and soft reset? can u post the picture here?
What´s the actiin botton?
That's the "select" button on the D-Pad... When you press directly in the center.
I tried put in bootloader mode but the pda not work. Maybe it´s a rom´s trouble?
When I put in bootloader mode, it show the work SERIAL V1.09.
Can I make a update the firmware without sync?

help !!! hardspl problem

please help me!!! after flashing Unsigned-Hard-SPL-Diamond-OliNex.zip on diamond screen appers this: YOU DON`T HAVE PERMISSION TO USE THIS ROM CODE and phone restart all time. What to do ? Urgent!!!
nobody knows ?
Download and flash another HardSPL. Maybe just a bad flash.......
but how to connect to pc ? phone restarts all time
did you hard reset?
Blazeitup123 said:
did you hard reset?
Click to expand...
Click to collapse
Yes, do a hard reset and wait till you can set date and time. That's where a connection with your pc is made. If mobile device center is connected, flash again the SPL.
Then do the same and flash ROM again.
Big thx to all. Only flashed another rom and problem solved.
Cannot get to set date and time
iXiR said:
Yes, do a hard reset and wait till you can set date and time. That's where a connection with your pc is made. If mobile device center is connected, flash again the SPL.
Then do the same and flash ROM again.
Click to expand...
Click to collapse
Hello,
After flashing, my MDA C4 with HardSPL 1.40 permanently reboots!
I tried Hard Reset, but it doesn't reach date/time screen
It formats itself, restarts and shows splash screen, after few seconds shows Radio/ROM versions on right bottom corner and restarts!
How can I get into flashable mode?
Enter in bootloader. Hold Volume Down button while with stylus press on reset button.
How can I reflash my device directly from bootloader screen???
borce_razor
THANK YOU!!!
the same way as you normally do

Help with HTC Touch Diamond, won't boot

Hello, this is my first post here. I tried to install Windows Mobile 6.5 as indicated in Gizmodo http://gizmodo.com/5281397/how-to-install-windows-mobile-65-right-now but it didn't work and now my phone won't boot.
The phone is an HTC Touch Diamond from Sprint. I followed all the steps indicated and everything look fine, but after installing the OS the phone displays the screen TOUCH DIAMOND, and then restarts and displays the same thing. I'm able to get into the boot loader (Tri color screen) and says:
DIAM500
SPL-0.57.CMONEX
MicroP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20.
I don't know what to do now
Thanks
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Flash from Olinex 1.40 screen?
okokur said:
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Click to expand...
Click to collapse
Hi I have the same issue on my HTC Diamond. I flashed wm 6.5 and it was working fine, then it hanged on titanum weather. I reset and it stayed on the HTC Diamond page, I did hard reset and got the Olinex 1.40 3 color page. It does respond from serial to usb when I plug/unplug. Can I reflash without active sync?
Turns out I was able to flash, but both roms I tried work well on 1st install, but stay stuck on the Touch Diamond screen everytime I restart de device. Is it a problem with the radio not compatible , or is there a specific Hspl for each ROM???
I found solution for this problem. If your diamond won't boot go to bootloader mode and upgrade your radio http://modmydiamond.info/index.php?option=com_content&task=view&id=15&Itemid=26 and after that your dimond worked fine without loosing data.
try to hard reset the phone by pressing vol down key + the center button + reset button.
if the problem is still like dat..
try to install another rom..
davidwong007 said:
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
Click to expand...
Click to collapse
Thanks davidwong007 for your help, I was experiencing the same issue as op and your method did the trick. For a minute there I thought I had bricked my HTC Touch. I did step by step what you suggested and ended up in the rainbox screen, once I was able to do that, I knew there was a hope. i did a full factory reset of the phone and voila the phone fully booted, the pain in the butt touchflow loaded. Very important thing I forgot to do in the past is to back up my phone, after the restore you will lose everything on phone, except what is in the internal storage. Thanks again.

Bootlooader problem, cannot enter bootloader

HI!
First of all... great forum.
Than.. I''ve got an Arte (SPV M650 from PL orange).
I've flashed it few times, trying to find ROM most fitting my needs.
So please don't answer if U want to teach me how to perform a SR, HR, BL enter. I really know that, i did it few times already
Problem is, that for some time, i can't get into bootloader. I want to flash my Arte again, now with Shady's ROM, but... i can't get into bootloader.
If anybody have a REASONABLE idea for help i would be grateful.
THX I A
sorry for my eng...
Same problem here
Same problem, when i wan t to go in bootloader is showing me a White screen.
Solved in this way: Hope is helpfull
I have a microsd card of 128Mb.
I put there a image of a rom, and rename it just like in sdcard flashing way "ARTEIMG.nbh". The i press it the tow side buttons ( off and voice ) and with slytus i reset keeping after reset the 2 buttons pressed. is comming in the bootloader mode, but is not flashing the image i put it in card. SO after that I install what rom i want.
This is my ay to escape from white screen and entering in bootloader mode.
I have also a big problem
my htc P3300 is blocking at boot menu( white screen ..htc..ipl 1.12.0001 SPL 1.12.0000 GSM 02.67.90 OS 1.12.0.0) i can not succed to make anything. so if you can help me it wil be great.. i also speak romanian so maybe it will be easyer to tell me everything in romanian. thanks alot.
Hi @all, try holding the power and record button and pushing the reset button. than you get into the bootloader. (hold power and record after resetting, too)
now you can practice sd card flashing.
i hope i can help you...
mike
where is the reset button? pls
kingoldstyle said:
Same problem, when i wan t to go in bootloader is showing me a White screen.
Solved in this way: Hope is helpfull
I have a microsd card of 128Mb.
I put there a image of a rom, and rename it just like in sdcard flashing way "ARTEIMG.nbh". The i press it the tow side buttons ( off and voice ) and with slytus i reset keeping after reset the 2 buttons pressed. is comming in the bootloader mode, but is not flashing the image i put it in card. SO after that I install what rom i want.
This is my ay to escape from white screen and entering in bootloader mode.
Click to expand...
Click to collapse
but...i do this and when i on my PDA , report "Invalid Certificate" ... pls help

Phone Freezing at phone lock - help

Hi,
I have Touch Pro2 on Vodaphone with the stock rom and today when i power on the phone it goes to the enter phone lock as normal but when i press the unlock key after entering the code nothing happens.
Is there a safe boot or anyway to get into the phone without doing a hard reset?
Thanks
Jason

Categories

Resources