Related
First, I would like to thank everyone on this forum for valuable information. I have been able to flash a Blue Angel and more recently a Universal (SPV M5000) with a Jasjar, O2 and Qtek ROM.
I have researched the forum but have not found any answer close to my problem.
After the lastest update (O2 Exec just released), I did not reset the unit properly and now my screen is completely dead/blank. I tried to reflash but it is no longer recognized (will not power back up)
No possibility in putting in Boot loader mode (power+light+reset) or doing a hard reset (the 2 _ and reset).
has anyone experienced this and can I revive it, at least, bring it back to a boot loader so I can reflash? Thank you to all :roll:
Just a thought. Have you tried leaving out the battery pack for a while, say an hour or better overnight? Might be worth trying the hard-reset sequence with the battery still out, then insert the battery and hard-reset again. If it responds, try flashing again.
It is possible to get the Universal in a totally confused state. Mine does this everytime if I power down the workstation *without* first disconnecting the Exec from the USB-Sync cable. Fortunately, it will respond after a battery out plus reset, then battery in plus soft-reset, so I don't actually have to clear the memory.
Hope you dig yourself out of the brown stuff!
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
Click to expand...
Click to collapse
No to do that , connect ypur ppc to pc amd flush again after finish just push reset buttom , you will be ok, otherwide try one more time
Unfortunately, I cannot flash because it will not power up or start the boot loader. The pc does not recognize the device
claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Click to expand...
Click to collapse
That worked for my when I was flashing my JAM, no problems. Scary, but successful. Think I may have left it a couple of days, to be sure. I then reflashed it successfully.
Although I refused to flash my Exec - too damned expensive to replace, and the ROM is 95% as good as it needs to be.
any one please could advise what happened and how to fix it?!!!
i've tried to update my s620 with
RUU_Excalibur_ROGERS_WWE_1.30.631.2_4.1.13.47_02.98.90_Ship.exe
found in this forum, the update went till 3% only and the device turned itself off, and won't turnd on again when i press the power, although the battery is full.
any ideas please??
thanks in advance.
bootrecord said:
any one please could advise what happened and how to fix it?!!!
i've tried to update my s620 with
RUU_Excalibur_ROGERS_WWE_1.30.631.2_4.1.13.47_02.98.90_Ship.exe
found in this forum, the update went till 3% only and the device turned itself off, and won't turnd on again when i press the power, although the battery is full.
any ideas please??
thanks in advance.
Click to expand...
Click to collapse
Hmm! I't might not work since it did'nt update ,but try hard reset , and if that doen't work you might have to go the bootloader way.
roloracer said:
Hmm! I't might not work since it did'nt update ,but try hard reset , and if that doen't work you might have to go the bootloader way.
Click to expand...
Click to collapse
am not too much to what you said,
could you please explain the hard reset process & the bootloader way process.
thanks anyway
bootrecord said:
am not too much to what you said,
could you please explain the hard reset process & the bootloader way process.
thanks anyway
Click to expand...
Click to collapse
Try hard reset first. http://forum.xda-developers.com/showpost.php?p=3263295&postcount=4
Bootloader http://forum.xda-developers.com/showpost.php?p=2191093&postcount=16
Now on bootloader you can only use your official 6.0 rom from Rogers . You can get it here.http://forum.xda-developers.com/showthread.php?t=381726
Scroll down to see Rogers 6.0
roloracer said:
Try hard reset first. http://forum.xda-developers.com/showpost.php?p=3263295&postcount=4
Bootloader http://forum.xda-developers.com/showpost.php?p=2191093&postcount=16
Now on bootloader you can only use your official 6.0 rom from Rogers . You can get it here.http://forum.xda-developers.com/showthread.php?t=381726
Scroll down to see Rogers 6.0
Click to expand...
Click to collapse
thanks,
there is no responce in anyway, i mean for the hard reset process, even when i connect it to the power supply -e.g. for charging- there is no leds turned on.
on the other hand, the Rogers ROM is the one that i tried to upgrade with; and it stuck at 3% then turned dead.
now it is with no power sign of any.
any further suggestions please??
bootrecord said:
thanks,
there is no responce in anyway, i mean for the hard reset process, even when i connect it to the power supply -e.g. for charging- there is no leds turned on.
on the other hand, the Rogers ROM is the one that i tried to upgrade with; and it stuck at 3% then turned dead.
now it is with no power sign of any.
any further suggestions please??
Click to expand...
Click to collapse
Take your battery out for a bit and try again "not promissing anything but sometimes can help"
stylez said:
Take your battery out for a bit and try again "not promissing anything but sometimes can help"
Click to expand...
Click to collapse
still the same; Dead.
thanks anyway.
there is no power in it,
as i mentioned before, even when i plug it to the charger, it remains the same: no leds, no power whatsoever.
any further sugestions please.
bootrecord said:
still the same; Dead.
thanks anyway.
there is no power in it,
as i mentioned before, even when i plug it to the charger, it remains the same: no leds, no power whatsoever.
any further sugestions please.
Click to expand...
Click to collapse
sorry it sounds like you have a fancy paper weight! Bricked!!
I installed Nataly Rom on my phone and since that time, my phone start to hard reset more and more often (3 times today)
Now I don't think that this has anything to do with the rom, but more with my phone.
Now, If I turn on my phone, I just get my red vodafone screen and nothing else happens.
I tried a hard reset, even with a complete format, wich now puts my phone completly bank, but still it won't pass my red vodafone screen.
Does anyone have suggestions of how to boot it up again?
please help
FuzzFuzz said:
I installed Nataly Rom on my phone and since that time, my phone start to hard reset more and more often (3 times today)
Now I don't think that this has anything to do with the rom, but more with my phone.
Now, If I turn on my phone, I just get my red vodafone screen and nothing else happens.
I tried a hard reset, even with a complete format, wich now puts my phone completly bank, but still it won't pass my red vodafone screen.
Does anyone have suggestions of how to boot it up again?
please help
Click to expand...
Click to collapse
try putting your phone into the bootloader screen and reflash with another rom.
I have a friend that had this problem with his phone. In his case there was a problem with the pagepool, installing a different rom as cobbs stated was the solution for him as well.
FuzzFuzz said:
I installed Nataly Rom on my phone and since that time, my phone start to hard reset more and more often (3 times today)
Now I don't think that this has anything to do with the rom, but more with my phone.
Now, If I turn on my phone, I just get my red vodafone screen and nothing else happens.
I tried a hard reset, even with a complete format, wich now puts my phone completly bank, but still it won't pass my red vodafone screen.
Does anyone have suggestions of how to boot it up again?
please help
Click to expand...
Click to collapse
some of us have had this problem already - my advice- use tbe search function 'cmd task 29' is the answer
Hi Gort
Thanks for the wonderfull advise.
I already thought my phone was a gonner, but now I can work with it again.
For all the people who experience a phone that keeps hard resetting more often and eventually cant boot at all, here's what to do.
Procedure:
1. bring the device to bootloader.
2. Launch ActiveSync on PC
3. Go to connection settings
4. Uncheck the Allow USB Connection
5. Now, run mtty1_1_.42_538 on PC.
6. If you have run mtty1_1_.42_538, just press the button USB
7. Type CMD
8. Type task 29 and let the program do his work a bit.
9. after that, flash with the rom of your choice
here is the link to mtty1_1_.42_538
http://forum.xda-developers.com/showthread.php?t=490182&page=4
Thanks for all the help guys, most appreciated
and hopefully this thread will help others now as well
edit: Link updated, should work fine now
problem flashing
hi fuzfuz thanks for the great advice ....the link for mtty1_1_.42_538 does not work ...can you let me know where to down load
thanks in advance
brightman said:
hi fuzfuz thanks for the great advice ....the link for mtty1_1_.42_538 does not work ...can you let me know where to down load
thanks in advance
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=3451487&postcount=41
[How To] Flash KS20 Complete Guide + Programms !!!
OK, I have really grown tired of people "crying" and wasting forum posts asking how to flash a rom, how their device can be recognized in LGMDP etc.
THERE ARE SOME MANY FREAKING GUIDES AND HELPFUL POSTS!
So I have created my own fully(I believe ) understandable guide on how to flash,brand,unbrand phone and restore .nv2 !
You can ask any question you want,nag to me,swear me,etc. I really like helping people!So please do not post in Spocky's or Farah's Threads for how to flash their roms!Everything you need is here!
***I am not responsible if you brick your phone or your dog dies ***
Guide Information:
www.mediafire.com/ibanezman192
If you appreciate my work,you can buy me a coffe!
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=RBB5HSMJGCWGE
great, I will check it out and try it.
Thanks, man.
You are welcome
When flashing my KS20 in emergency mode, after ~10 sec the LGMDP said something about an QCSBL writing error, or somethint li that. I pressed OK too early
Now my phone doesn't work, can't turn it on and no emergency mode. What can I do now?
Take out the battery,insert it and do a hard reset.
help...
hi ...i have a problem with my ks20...i'd installed application from htc, opera browser build for wm6.1 or 6.5...at first it worked but after soft reset my phone dont open anymore...it stock on the bootloader showing lg icon only...is there anyway for me to hard reset my ks20...please help if somebody knew or experienced this....thanks
algabz said:
hi ...i have a problem with my ks20...i'd installed application from htc, opera browser build for wm6.1 or 6.5...at first it worked but after soft reset my phone dont open anymore...it stock on the bootloader showing lg icon only...is there anyway for me to hard reset my ks20...please help if somebody knew or experienced this....thanks
Click to expand...
Click to collapse
1)Wrong thread.Please do not post irrelevant things.
2)Download my guide and you will see how you can hard reset.But I cannot understand why your phone hungs up!I do not think this has to do with opera.I have opera and it works fine.
Help! My LG KS20 is dead!
I have tried searching, but nothing came up.
Yesterday while flashing, it said something timeout (1st time the bar runs across)
Now, I cannot activate emergency mode. I cannot charge the phone. There is no response, no light. Charging the battery full has no effect. Taking the battery out has no effect too.
Is there any way to fix this? My warrenty expired just yesterday
ryanswj said:
Help! My LG KS20 is dead!
I have tried searching, but nothing came up.
Yesterday while flashing, it said something timeout (1st time the bar runs across)
Now, I cannot activate emergency mode. I cannot charge the phone. There is no response, no light. Charging the battery full has no effect. Taking the battery out has no effect too.
Is there any way to fix this? My warrenty expired just yesterday
Click to expand...
Click to collapse
Very strange problem!Maybe your battery is dead Take out the battery and connect the mobile with the pc.If nothing happens then it is not a battery problem.Have you tried a correct hard reset?By saying correct, I mean holding the 3 buttons for many time until the leds flash and then flash out.Then you must release the buttons.
Thanks ibanezman for your reply...
Nope, nothing. Battery is fully charged (I have an external LG charger that was given free).
Nothing happens when I remove the battery and connect to computer. I cannot do a hard reset, because there is no LG logo, and no lights. Not green, red, or blue.
I can't flash in emergency mode, because holding down Internet Explorer and Power gives nothing. No usual green light. Laptop doesn't detect anything. Nothing in device manager.
Today while going through the logs in the LGMDP folder I came across this.
<AppName>Log For Web DownLoad</AppName>
<TIMESTAMP>20090908235324</TIMESTAMP>
<Date>2009-09-08</Date>
<Time>23:53:24.-473</Time>
<IMEI></IMEI>
<TIMESTAMP>20090908235324</TIMESTAMP>
<RESULT>FAIL</RESULT>
Notice there's no IMEI number? Could this mean anything?
ibanezman192 said:
Very strange problem!Maybe your battery is dead Take out the battery and connect the mobile with the pc.If nothing happens then it is not a battery problem.Have you tried a correct hard reset?By saying correct, I mean holding the 3 buttons for many time until the leds flash and then flash out.Then you must release the buttons.
Click to expand...
Click to collapse
I do not think this has to do with IMEI.Maybe you have lost your IMEI in the flashing process.But I believe your phone is dead/bricked
I really cannot feagure out any other suggestions.Maybe you should take it to LG Service.
ibanezman192 said:
I do not think this has to do with IMEI.Maybe you have lost your IMEI in the flashing process.But I believe your phone is dead/bricked
I really cannot feagure out any other suggestions.Maybe you should take it to LG Service.
Click to expand...
Click to collapse
OK thanks ibanzeman. I think i will just let the ks20 go and buy a new phone.
Anyway its old already, and i think i bricked it. Thanks for your assistance anyway!
ryanswj said:
OK thanks ibanzeman. I think i will just let the ks20 go and buy a new phone.
Anyway its old already, and i think i bricked it. Thanks for your assistance anyway!
Click to expand...
Click to collapse
I'm sorry I couldn't help you, good luck finding a new phone!
thanks man. i will give this guide a go!
ibanezman192, thanks a lot for this very detailed guide!
hibjibis said:
thanks man. i will give this guide a go!
Click to expand...
Click to collapse
spuke said:
ibanezman192, thanks a lot for this very detailed guide!
Click to expand...
Click to collapse
The pleasure is all mine New version of the guide is coming tomorrow
erm.. can someone help? my computer doesnt seems to recognise my KS20 during Emeregency mode
I have same problem. On Win 7 64 bit, LGMDP do not see KS20.
What is the message that appears?
Link don`t work
Hi,
I try use the link for download the archive, but the link dot work....
You can fix this??
Thanks
PS: sorry for my english, but i am not very good in this language
Hi guys,
Can anyone help me here ?
When I try to start up my Phone, it always loads the bootloader ...
I tried running reflashing a rom and task29, but no help there :s
Does anyone have an idea what to try ?
Tnx
Nick
Some people with the same problem said that their batterie was broken. Can you try another batterie?
I'll give it a try
Will let you know ...
Lennyz1988 said:
Some people with the same problem said that their batterie was broken. Can you try another batterie?
Click to expand...
Click to collapse
Nope, doesnt help.
Tried with a friend's battery, and have the same result.
Also tried using his phone with my battery and worked perfectly.
Any other ideas?
Trickass said:
Nope, doesnt help.
Tried with a friend's battery, and have the same result.
Also tried using his phone with my battery and worked perfectly.
Any other ideas?
Click to expand...
Click to collapse
Just to ask: You're not (accidentally) holding down the volume key when you press the power key (or reset) to turn on, are you? That puts it into bootloader.
MCbrian said:
Just to ask: You're not (accidentally) holding down the volume key when you press the power key (or reset) to turn on, are you? That puts it into bootloader.
Click to expand...
Click to collapse
No, I'm not doing that
I thought maybe it got stuck though, something like that :s but when I do press it, I hear a pretty clear "click", so I guess it's not broken at all...
Also, I noticed that when I try to reflash a ROM, the "current image" (or whatever it's called) is blank ...
(I mean the thing that sais the version number of the currently installed rom)
Okay, sounds dumb I know, but did you flash a new rom after flashing Task29?
It is used to wipe the OS out completely BUT you then have to re-install a new OS...
Just thought I'd ask.....
Same issues.
Same issues on my touch pro 2.
The only solution i find in order to make it boot is with mtty on a Windows xp pc with no activesync.
Perform a
set 14 0
task 8
then the phone boot on the os but on the next reset stay in bootloader !
ultramag69 said:
Okay, sounds dumb I know, but did you flash a new rom after flashing Task29?
It is used to wipe the OS out completely BUT you then have to re-install a new OS...
Just thought I'd ask.....
Click to expand...
Click to collapse
Lol yeah I know that
Thanks anyway
Frederic.james said:
Same issues on my touch pro 2.
The only solution i find in order to make it boot is with mtty on a Windows xp pc with no activesync.
Perform a
set 14 0
task 8
then the phone boot on the os but on the next reset stay in bootloader !
Click to expand...
Click to collapse
Hm, I'll see if I can find a Windows XP pc somewhere and try ... MTTY doesn't seem to work with Win7 x64
Trickass said:
Lol yeah I know that
Thanks anyway
Hm, I'll see if I can find a Windows XP pc somewhere and try ... MTTY doesn't seem to work with Win7 x64
Click to expand...
Click to collapse
Hummm i have see somwhere a howto for mtty on W7... but i'm a little lazy i have choose to do this on a old windows xp
But this command are just temporary i'm searching for something more stable !
Some news from my Rhodium Stuck in bootloader
I have try to Hardspl it (Olinex 0.85)
The good news is i have manage to do it, the bad news is after that even the
set 14 0
don't manage to make it boot.
After a while searching, (thanks wiki of another phone) i have find those command :
password BsaD5SeoA
set 14 0 # Maybe it's usless now but in fact i don't know
set 1 0
task 8
And now i'm back to my start....
I tried using the MTTY commands, and when I did it the first time, the phone booted and performed its "first run setup" thing.
After rebooting though, it went back to the tricolor screen, and I can't get past it anymore, even with the same MTTY commands ...
Any other ideas ? :/
mtty, a lot of post on the internet...
hi,
I think we are a the same point !
I have find a way to start a boot with the HTC screen but the phone tel me that a txt file is missing on the sd card ???!!!???
with mtty :
boot
yes it's quite simple why i haven't think of that befor i don't know... but that didn't solve my problem at all.
I have send a mail to HTC in order to have a diferent point of view but all they said to me is doing a hard reset (who didn't do anything...)
I will post the avancement of my test but i feel a little stuck.
Note : After searchin on the internet, the set 14 0 tel to the phone to boot on the os after a flash (sometime the phone don't reconize the end of flash)
the set 16 0 (or set 16 1) disable (or enable) the RUUNBH tag on boot loader.
More Infos...
I have find a post on a other forum whos said that a defective battery could result to an unstable beaviour of the phone.
I have let it without battery for a day and, today it has directly boot on the OS.
I have ordered a battery on ebay and waiting for it maybe the solution ?
Frederic.james said:
I have find a post on a other forum whos said that a defective battery could result to an unstable beaviour of the phone.
I have let it without battery for a day and, today it has directly boot on the OS.
I have ordered a battery on ebay and waiting for it maybe the solution ?
Click to expand...
Click to collapse
Oke, I will try to take out the battery tomorrow as well ... Although, I tried using a different battery and it didn't help ...
Right now, I managed to boot using mtty set 14 0 > task 8, which seems to work
(sometimes, I need to do the task 8 twice in a row ...)
So as of now, I managed to flash a stock rom onto the phone, and only have to try and reset hardspl back to stock as well.
Waranty here I come ...
lol mine is out of waranty, and it's the solution i ve find everywhere !
did you try hard reset by holding the call and hang up button together when you power up the phone.
last time I remove a program and tha cause me to boot ot a black screen after teh bootloader. Hard reset fix the issue as it return teh phone to the sotck setting of the rom.
PUTALE said:
did you try hard reset by holding the call and hang up button together when you power up the phone.
last time I remove a program and tha cause me to boot ot a black screen after teh bootloader. Hard reset fix the issue as it return teh phone to the sotck setting of the rom.
Click to expand...
Click to collapse
yes, i've try it (HTC has send me the same advise) and... same issue !
In order to done the hard reset (who didn't execute when the phone is to boot in bootloader) i have do a set 14 0 and reset with power and holding the two call hang and power.
But thanks for the advise !
Frederic.james said:
lol mine is out of waranty, and it's the solution i ve find everywhere !
Click to expand...
Click to collapse
Out of warranty ?
How old is it then ?
Mine is just under 1 year old, so I'm lucky I guess ... and I hope
Trickass said:
Out of warranty ?
How old is it then ?
Mine is just under 1 year old, so I'm lucky I guess ... and I hope
Click to expand...
Click to collapse
Hum it's the phone of a firend who give it to me... and he has buy it on e-bay.... for the waranty sound difficult to retreive a bill and... I will search till i find something to do