When I have used my mda for a phonecall, or when I used it not so much my Qtek 9090 won't respond to the on/off button. The screen won't light up, although my bluetooth and my carrier/cellphone light is flashing.
What can be wrong? The only solution then is a soft reset ( once a day ! ) :roll:
Related
:?:
Hi,
I was wondering if anybody can help me assigning a hardware button to turn flight mode on/off. I am using Vito Button Mapper program. I can assign a hard ware buton to turn the power on/off but still have to take out stylus to turn off the phone (a.k.a flight mode). Any help will be greatly appreciated.
Thanks
read this thread and get the EXE, then map your hardware button.
http://forum.xda-developers.com/viewtopic.php?t=13377&highlight=radio
Thanks for your help. I just downloaded the cab file. I'll try it and let you know if it worked.
Thanks again.
Keep in mind that the difference between radio on-off & flightmode is that with flightmode ALL radio's (GSM, BT) are switched off
Radio on-off only toggles the GSM Radio.
This is handy when during switching off-on (ie when you use a dual SIM)you want to maintain ie your BT GPS connection.
Thanks again for explaining the function of radio on/off program. I did downloaded the program but for some reasons it did not work on iMate PDA2k. It also made the flight mode inoperable even with stylus. Once I uninstalled the program, now flight mode is working again with stylus. Oh well, I tried. But I do appreciate your help.
Thanks
It works on my PDA2k... you may want to try a reset after installing.
Outz:
You are right. It did work after I reset the PPC. I guess I was too impatient. There is a very slight time lag after I push the button (althout less than a second) but I was not waiting long enough. Secondly, I noticed if I don't have any signal in a particular area, delay to turn off is even longer but I am so glad it works.
Thanks for your help.
Press and hold "end call" red button for 3 seconds.
bdarras: Thanks for your tip. I already tried that because it did work on MDA II but not on MDA III (or PDA2k).
you're right!
I just gor my xdaIIs yesterday, I didn't realize they had disabled it!
Hi, I've just gotten a BA from a friend which seems to have a little fault. When i turn on vibrate mode via the Today Screen or switch the ring type to "Vibrate and Ring", the phone's screen turns white and the whole phone kind of soft reset itself when
1. There is an incoming call or
2. I pressed the play button to hear the ring tone in the settings menu.
It is initally running on wm2003 and after upgrading to helmi's latest wm5 rom, the problem still exists. Is this a hardware or software problem? Any help will be appreciated
Hi everyone, i've got problem with this device.
Device is running normaly, but the display remains off(black), if you turn on the BA, there are stripes for a second, but then they dissapear.
MDA is making noise(clicks, warnings etc), you can use touchscreen but the screen is still black.
It has been in this state from yesterday, I was listening to the music via TCPMP, once I turned off the screen but later It couldn't become on...
I've formated it already....It didn't have effect
Thanks for help
ps I cant do the hard reset because I dont know what I have to push to do it (foto, record ??!)
try pressing the power button for a long time.
regarding the hard reset. IT's in the WIKI.
or use the search function for "hard reset".
Hi.
HTC Blue Angel won't go to standby (sleep) mode when i press the power button.
Here's what i've tried alredy:
- soft reset
- hard reset
- reformat
- reflash
The power button electricaly is working since i can wake the device and toggle backlight with it. The sleep mode is operational since the device automaticaly timeouts to the sleep mode (power management).
Now the most intriguing part: this has happen to TWO of my Blue Angels at the SAME TIME. One with WM2003 and the other with WM6.
The WM6 was my primary unit while the WM2003 was just lying in the drawer.
When the WM6 unit gone mad i took out the MW2003 one just to find out it has the same problem. While i did instaled some software on the MW6 one i haven't installed anything on the MW2003.
Any help apriciated. Thanks in advance.
Bushman
when you say sleep mode you mean the screen goes to blank and the backlight turns off...right?
try pushing the button longer
try pushing the button longer
red_hanks said:
when you say sleep mode you mean the screen goes to blank and the backlight turns off...right?
Click to expand...
Click to collapse
Yes, the mode where PDA is turned off (apps are hibernated) but GSM radio is still on standing by for incoming calls/messages.
iarrywalker said:
try pushing the button longer
Click to expand...
Click to collapse
That's pointless. This device has backligh turned on/off that way, not the OS. When everything was ok, a short push was enought to trigger the "standby" function. (once again i remind that the button is electricaly ok)
Thanks for reply, waiting for ideas,
Bushman
MINE TOO
that happens to me too andthe keyboard smtyms hangs until you press the windows button
I have pressed each and every key on the device multiple times, nothing helps
I had the same problem.
The reason was one of the keys beside the display.
In older PPCs these buttons tend to get short-circuited.
My solution was to reassemble the BA and clean the buttons.
Thank you for the tip, i will clean the buttons and check connections to the mainboard and post results.
Thumbs up!
Bushman
EDIT:
Thanks for the tip!!! One is fixed. The other one still doesn't work like it should but now i have a clue where to search for it.
Bushman
Ihad to pimp my BA and it happends to mee
And the button record remains pusshed ll the time
it can let the power off works
I just
break the button
and voila! it works again...!
good luck.
Hi ive recently upgraded my WM5 to Schaps 4.31 WM6 ROm
but now theres a peculiar problem
when the screen switches off due to power saving/key lock
i cant wake it up again without doing a soft reset.
Any ideas why this might happen ? or how to solve it ?