BA won't go standby by power button. HELP! - MDA III, XDA III, PDA2k, 9090 General

Hi.
HTC Blue Angel won't go to standby (sleep) mode when i press the power button.
Here's what i've tried alredy:
- soft reset
- hard reset
- reformat
- reflash
The power button electricaly is working since i can wake the device and toggle backlight with it. The sleep mode is operational since the device automaticaly timeouts to the sleep mode (power management).
Now the most intriguing part: this has happen to TWO of my Blue Angels at the SAME TIME. One with WM2003 and the other with WM6.
The WM6 was my primary unit while the WM2003 was just lying in the drawer.
When the WM6 unit gone mad i took out the MW2003 one just to find out it has the same problem. While i did instaled some software on the MW6 one i haven't installed anything on the MW2003.
Any help apriciated. Thanks in advance.
Bushman

when you say sleep mode you mean the screen goes to blank and the backlight turns off...right?

try pushing the button longer
try pushing the button longer

red_hanks said:
when you say sleep mode you mean the screen goes to blank and the backlight turns off...right?
Click to expand...
Click to collapse
Yes, the mode where PDA is turned off (apps are hibernated) but GSM radio is still on standing by for incoming calls/messages.
iarrywalker said:
try pushing the button longer
Click to expand...
Click to collapse
That's pointless. This device has backligh turned on/off that way, not the OS. When everything was ok, a short push was enought to trigger the "standby" function. (once again i remind that the button is electricaly ok)
Thanks for reply, waiting for ideas,
Bushman

MINE TOO
that happens to me too andthe keyboard smtyms hangs until you press the windows button

I have pressed each and every key on the device multiple times, nothing helps

I had the same problem.
The reason was one of the keys beside the display.
In older PPCs these buttons tend to get short-circuited.
My solution was to reassemble the BA and clean the buttons.

Thank you for the tip, i will clean the buttons and check connections to the mainboard and post results.
Thumbs up!
Bushman
EDIT:
Thanks for the tip!!! One is fixed. The other one still doesn't work like it should but now i have a clue where to search for it.
Bushman

Ihad to pimp my BA and it happends to mee
And the button record remains pusshed ll the time
it can let the power off works
I just
break the button
and voila! it works again...!
good luck.

Related

Power button problem

Hi all,
My XDA IIs works well before. But few days ago the Power button doesnt work properly, it can turn on the phone, hold to turn off the back light, but I can't use it to turn my phone screen off like before. Anyone has same problem ?
Can you see any part of the screen? It might just be that the backlight adjustments are set too low when the unit isn't cradled. You might be able to see the screen in daylight.. or maybe it was inside your home. I forgot where I was at when it happened to me. In anycase, if you can see a bit of images on your screen, go into the Backlight properties and change the setting to your liking.
Good luck..
The problem is i can just press the power button to turn off my phone BEFORE (the screen is completly off), and NOW it doesnt work at all ! When my phone was off, I can press the Power button to turn it on, or when I hold it for few seconds the back light will be turned off, but press once to turn off. I dont know why, if somthing wrong with the Power button it should be doesnt work at all, that's mean i cannot turn on my phone as well. But other functions of the Power button are still work well, except the 'Turn off' :roll:
power off doesn't work anymore
I have the same problem here. I can't use the power button to power off my qtek 9090!!
i can use the power button to turn my pda on and to switch the background light on and off - so the "hardware side" of the power button is working.
however, i can't use the power button to turn off the device. it's very annoying, because i can't put it in my pocket after finishing a call :-(
this should be some sort of a software problem - so i hard resetted my device (a couple of times) - but that didn't help!
can anyone help?
thanks,
lorenz
the ba doesn't turn off it is always on staand by mode. ->settings -> system -> button lock
this will stop any missed call because when the ba is in standby the power button is the only one to work
power on is no problem. i can't put my BA into standby mode. if i press the power button while the BA is turned on, nothing will happen. the screen will stay on, the background light stays on.
i have no way to put it into stand-by with the power button!
try this and see if it works. it's a software app that wil rest, shut down, and turn the screen off. just copy it to your BA temp directory and install it.
power button problem
nemchua
Is your problem solved ?
Because I have the same problem.
Power of switch doesn't work !!!
Any help would be welcome.
power button problem
Does anyone solve the problem???
Had the same problem...
I had the same problem going on for about two weeks or so...never changed anything and it went away all by itself.
The problem has not come back now in over 4 months.
Sure would love to know what the problem was tho...
Greetings,
Noddy
Power Off does not work
Add my name to people with this problem.
The only event I can link it to is this: I deleted my Motorola Bluetooth headset and installed a Logitech headset. I noticed the problem (can't turn OFF with POWER BUTTON) soon after that.
same problem for me ..... someone must know !!!!
I think it is a hardware problem. The contact is not making cleanly. Disassemble and spray time, perhaps.
It's a standard push switch, easy enough to replace, I occasionally list themon ebay but any phone repairier should have them in stock.
Richard
i had same problem yesterday afternoon, but it is ok now. recovered by himself
Write again in two weeks and let us know if it is still healthy. In my case, anintermittent problem became continuous.
Can't turn the screen on after pressing power button
I have a problem with my Bell Atrix. After pressing power button to lock the screen, i can't wake up the screen up by pressing that button again. Could anyone tell me how to fix it pls.

Can't power off... volume goes down by itself...

Guys, need help... can't figure out if it is a soft or a hard problem...
Have had SX66 for 3 years. Almost never a problem (except for occasional thing when people could not hear me, I could hear them, but after soft reset that thing usually corrected itself).
However, just recently got a real problem.
- Can't power it off. Power buttom only works on powering on, but not on powering off.
- At the same time, the volume window pops up (with two volume sliders, "on", "vibrate", and "off), and the left slider automatically slides down on its own, preventing me from accessing anything else. When I try to do something else, go to Programs, or else, this freaking Volume window keeps popping up, and left slider keeps going down and stays down there.
When I try to increase volume, it keeps going down right after I raise it. And the volume window is almost constantly popped up.
From time to time, it disappears, allowing me to do something for several seconds or even minutes, but then pops up again.
Yesterday, I even managed to do something for several minutes without it, and even managed to turn SX66 off, although I had to press the button for a second longer than usual to turn it off. Today, no luck, can't power it off. If I press it for a bit longer, it just goes in "dimmed" screen mode, but stays powered on.
Any advice?
Thanks.
I guess, I'll have to try to clean the power button and volume slider on the side. Looking for good disassembly instructions. Found one, but more would be appreciated...
http://pdasmart.zftp.com/instructions/sx66_09.pdf
pecq said:
I guess, I'll have to try to clean the power button and volume slider on the side. Looking for good disassembly instructions. Found one, but more would be appreciated...
http://pdasmart.zftp.com/instructions/sx66_09.pdf
Click to expand...
Click to collapse
Check the wiki, there are disassembly instructions in there.
Did you solved your problem ? I have hte same only my volume go up ...
i need help
hi everyone...i need help ...coz my qtek 9090 windows 2003 is stucked when i was upgrading it ..now it shows only written serial v2.06 or usb v2.06...and screen back light is off,i tried many things...bt i failed now pls somone help me....soon ..
maybe the problem is not in button but in varistors because they can do this...
pecq said:
- Can't power it off. Power buttom only works on powering on, but not on powering off.
Click to expand...
Click to collapse
I have the same problem. I was starting to think that there is no way to turn of BA . Any help?
I have the same problem, only that mine is a HTC touch dual (niki).
the volume screen keeps popping up, and does a "volume down" command... sometimes it goes away, sometimes it comes back...
:S
Ive got a similar problem ive upgraded my BA to wm 6.1 (Xplod) the problem that i am having is that i cant seem to power it off..only way that im able to do that is by removing the battery..when i keep the power button pressed only the backlight turns off but no the phone..How to i power it off?
and secondly ive a problem with the keyboard..while writing some times i press a key and it keeps typing that for example i write s it keeps writing ssssss or giving spaces untill i press something else...is this a software issue or a hardware issue..cant seem to figure it out
I know this thread has been a while but if anyone has the same problem, you'd probably be interested about what i did.
well i had the same problem of the volume going down by itself and the volume icon pops which basically lets you do nothing.
tried all the approaches thinking it was a software issue. but i finally went nuts and took my torx screwdriver, opened the blue angel and tore off the part in the motherboard where the outer volume lever is attached to.
It worked.
So if you could with the fact you wont a direct volume adjustment at the side, you could probably try it

Can anyone help me with my hermes prob?

I'm using K's ROM .
Just recently my phone has a problem. As usual when my phone is put idle for a while it'll turn off , and u need to press the power button to activate it right. Then sometimes when i pres the power button, nothing appears in my screen, I press and press nothing happen. Then u can see the power indicator is still blinking. I cant do anything but to reset it by pressing the hole down there with the stylus.
And sometimes when activating , it seems completely shut down and when i press the power button and it shows the start up screen , and the whole PDA is rebooting.
OMG... Is my phone screwed?
you issue is called the sleep of death (SoD), i personally never had that issue, so i cant help you there. but you should search and see what others with this issue did
May help....
DavidZMetal said:
I'm using K's ROM .
Just recently my phone has a problem. As usual when my phone is put idle for a while it'll turn off , and u need to press the power button to activate it right. Then sometimes when i pres the power button, nothing appears in my screen, I press and press nothing happen. Then u can see the power indicator is still blinking. I cant do anything but to reset it by pressing the hole down there with the stylus.
And sometimes when activating , it seems completely shut down and when i press the power button and it shows the start up screen , and the whole PDA is rebooting.
OMG... Is my phone screwed?
Click to expand...
Click to collapse
1. I do believe that was caused by installed softwares,
2. try to remove all today plugins, wait 5 seconds, softreset, after 2 minutes (just to ensure
all processes are finished),
3. try to press the power button then again after 10 seconds, and see if that helps or not, alternatively,
4. try to remove the shortcuts fron the startup folder and try. If nothing helped, probably there is a confused registry. hard-reset for no choice(except you are expert in registry matters )
5. Remember to wait for 10 seconds before you reset the device after changes were made.
thanks everyone!! this problem happens occationally. SO i need a few days to see if the above steps work
Thanks for ur advice again though

Power button doesn't work after boot

So here's my problem, I can press the power button to start up my touch pro 2, but after the OS loads, it doesn't function to turn off the screen or to power off my device. So now, it just goes dim after 30 seconds but still stays lit and the only way to turn the phone off is to pull the battery. What can be done?
8gkl said:
So here's my problem, I can press the power button to start up my touch pro 2, but after the OS loads, it doesn't function to turn off the screen or to power off my device. So now, it just goes dim after 30 seconds but still stays lit and the only way to turn the phone off is to pull the battery. What can be done?
Click to expand...
Click to collapse
Witch rom do you use? What kind of cabs did you install? Other tweaks? Please be more specific so we can help
Stock Tmo Win6.1 rom. Nothing installed really, this problem was present ever since the fresh install. It can't be physical because the power button is recognized prior to OS boot, and I can get into the bootloader fine as well.
Maybe there is some software that can map the keys properly?
Try this program and see if it solves you're problem. I will let you remap you're hardware keys.
http://forum.xda-developers.com/showthread.php?t=554240
That program doesn't let me do anything with the power button. It doesn't even let me assign a power button FUNCTION to the end button. I don't know what's going on.
There are different restart programs you can install that will include an app. You should change the times for your screen to turn off as well. If there isnt' water damage take your phone in to the provider and you should be able to get a new one.

Major Catch 22 - Desire got Wet now have 3 issues! PLEASE HELP

Hi guys.
So i managed to get my desire wet/damp and whilst it still works it has developed 3 issues:
1) The weirdest of all - the phone wont go into standby, as soon as you press the power button or let it timeout the screen goes off and they instantly turns back on to the lock screen. If i leave it, it will timeout again on lockscreen and come back on, it does this forever. I have done factory resets etc, all the same. Weird right. As i result i would like to reflash the mod and see if that fixed it as assuming its software related (somehow).
2) Volume keys do not work - think means i had issues getting into recovery. Finally found a widget to do it and then....
3) Trackpad does not work in recovery so i cannot re-flash or try any new rom to see if that fixed (1)
Proper catch 22
Any suggestions appreciated.
Thanks
Bridgstfer
Install 4ext touch recovery.
Update after installing touch recovery
OK I HAVE AN UPDATE:
The plot thickens but i have managed to S-OFF my Desire and eventually install Clockworkmod Touch which obviously doesn't require me to use the trackpad button so I was able to use Recovery. I wiped the phone and tried reflashing the ROM i had been using (Insertcoin) but this made no difference, the phone still keeps waking up immediately that it goes to sleep (either with power button or by sleeping timeout).
So i decided to install a completely different ROM (CM10_VJ_4.1.2_v3.0) and this installed fine. Now the phone will go to sleep and stay asleep if I press the power button. Problem solved I thought!
Now when the phone is asleep 50% of the time, trying to wake it with the power button will cause it to reset immediately and goto the white HTC screen. When it restarted it sits on the unlock screen and keeps timing out, screen goes off, then immediately on again - weird. If i unlock and lock with power button it will behave. For some reason the Search key will wake the phone every time no issues. Only the power key to unlock causes it to reset. Phone is sleeping according to Battery info.
Any other suggestions for what I could try. Could this possibly be something hardware related now? If there a way i can log the key presses or reason it wakes/resets?
Any help really appreciated, the phone is pretty unusable with this reset issue now.
THanks
Bridgstfer
theres a few videos on youtube, if it was me i would take the phone apart and clean all round the buttons. mite solve it. But as it got wet, the water could of damaged something in around the trackpad r power button, hense always waking the phone.
Sent from my HTC Desire
Thanks mate. So i tried this and installed CM7 today and have discovered something. As i said above the volume down button doesn't work and the volume up only works with some persuasion. Once i installed CM7 the problem where I lock phone with power key and it instantly wakes up now persists (on the JB rom it at least stayed asleep but reset if power button was pressed again).
However whe i changed the display timeout to 15seconds i watched as it timed out and instantly woke then noticed the volume would increment down one notch each it woke up again. This leads me to think that rather then the volume down not working at all it is actually stuck down permanently and could be causing the issue here. Is there any way I can find out if this is the case and disable the volume keys through software or do i need to open up the phone and disconnect it?
Thanks for any help - i think we are getting there!
Bridgstfer
I actually worked out that the trackpad is being pressed down constantly too because on CM7 when i disable trackpad to wake the phone actually stays asleep. Stil the phone resets if i try to wake with power button though, must be something to do with the button combo being held down.
Is there any way to disable both volume and trackpad buttons at the kernal/system level?
Tried button remapper but does not allow to remap the trackpad press.
With a file explorer, go to
system>usr>keylayout and modify bravo-keypad.kl.
I'm just back from holiday where my Desire had a ten-minute swim in sea water!
Naturally it was stone dead when I remembered it was in my pocket as I waded across an inlet which was supposed to be ankle- deep but was over 1.5 metres in places
I thought there was no point in drying it out without first removing all salt so (minus battery and cards) held it under a tap for several minutes then left it to soak in tap water in the sink for 30 minutes.
I then dried it over gentle heat for a few days then tried the battery. The vibrator ran continually and the white LED flashed randomly but nothing else. After another two days drying it booted - but only into Fastboot and the vol switch didn't move the cursor. But after another two days - it worked almost perfectly! The vibrator is dead and the screen a bit streaky, but all the other sensors work just fine and it's quite useable.
I had been logging the hike using My Tracks and it actually shows the course going a short way into the sea.
do you have an assurance or warranty?
if yes-->change phone.
abaaaabbbb63 said:
With a file explorer, go to
system>usr>keylayout and modify bravo-keypad.kl.
Click to expand...
Click to collapse
Thanks for this. I actually got an app that let you remap the keys but it does not let you do anything to the trackpad click button (which is now the one stuck down). See photo of whats in my bravo-keypad.kl file here:
http://dl.dropbox.com/u/64089332/20130106_194659.jpg
Any other way i can disable the trackpad completely. Perhaps at the kernel level?
Thanks

Categories

Resources