Could you guide to download new rom XDA II 1.66 with .nb1 file.
I found only xdaii_upgrade_16044eng.exe, how can I copy it to my SD and upgrade from bootloader?
Thanks
no your bootloader cant execute pc exe files
heck if you just copy the nbf file from inside the exe file to the sd card it will not work
read this
http://forum.xda-developers.com/viewtopic.php?t=8205
Does Anybody Have xdaII_upgrade_16044eng.exe
Please Help Me!
I Need this file to fix my XDA II Phone.
i've do something terrible with my XDA II while upgrade rom, and when i restart my phone it's only show serial.....................v1.06 that's all.
so, please help me???????????????????????????
Way around the model ID 100 error...but still not out of the
I don't think that is going to help you.... I have the same problem.
I am stuck in bootloader mode (1.06 is the new version).
things I have noticed about this bootloader (as I have spent lots of time with it...))
1. The Password BOOTLOADER is enabled on many of the commands (I understand it was not on the earlier versions) in this new version.
2. I have a bunch of XIP roms and even a few NB0 roms, and I cannot just "lnb" or "l" them over as they want start addresses and the lot (defaults do not work for either.
3. As I have access to another XDAII in the morning, I have not tried to erase the ROM on my device with the erase command. Even though I think that will solve the problem, I don't dare tempt fate again.
3a. A way around the Model ID error is to cold boot, or reset at just the right time in the upgrade program (this is when the device shuts off - or goes blank). This will then fake out the upgrade program and it will continue. However, with my problem, I get stuck at the first step of "erasing ROM". IT apparently times out as it is unsuccessful and gives you an error reading something like "there was a problem -- reset and try again" Since my problem is self inflicted (I upgraded but deleted the Radio stack and OS from the temp directory -- something the instructions tell you never to do --> but red letters or bold typing that little fact in the instructions may have helped me not to miss it!!)
3.b Maybe this info would help others in the same boat -- maybe not.
4. I am convinced that the problem is related to the new bootloader version and if I could down grade it, all would be well. But I am not that brave - would rather wait to D2S a good ROM from a good XDA2, then gamble further.
Does Anybody Have xdaII_upgrade_16044eng.exe
Please Help Me!
I Need this file to fix my XDA II Phone.
i've do something terrible with my XDA II while upgrade rom, and when i restart my phone it's only show serial.....................v1.06 that's all.
so, please help me???????????????????????????
Re: Does Anybody Have xdaII_upgrade_16044eng.exe
Ayu said:
Please Help Me!
I Need this file to fix my XDA II Phone.
i've do something terrible with my XDA II while upgrade rom, and when i restart my phone it's only show serial.....................v1.06 that's all.
so, please help me???????????????????????????
Click to expand...
Click to collapse
Ayu... XDAII-nya kenapa? Lu apain? Coba sini gue liatin. Telpon gue di 08158014342. Di Jakarta kan? Kalau di Jakarta langsung aja kita ketemuan. Mudah2an gue bisa bantu. Lama2 bule2 sini kayak TAI!! XDAII gue mati nih gara itu TEST ROM!! MONYET!! Gue kesel banget tuh ama yang posting itu ROM!! Ya... Gue juga sih yang geblek!! :lol:
Sir. Rudegar
I found 2 files of .nbf, so I have to run XDA OS ImageTool 3 times to copy to SD card right?
Can I don ony ms_nbf and NK.nbf?
Thanks
http://forum.xda-developers.com/viewtopic.php?t=8606
http://wiki.xda-developers.com/wiki/HimalayaRomFlashing
this should explane it step by step
no upgrade possible with HimaUpgradeUt.exe
I have tried a lot of different ROM's and different ways to upgrade my MDA II with HimaUpgradeUt. But the result is alwasy the same. MDA II starts in bootloader mode and I can only reactivate the device with a old ROM via SD card (image written via ntrw.exe).
Please can someone help me or can provide a ROM image from his device (MDA II, latest version, german or english).
Thanks.
Related
Hi all.
I just bought my XDA IIs some days ago in HongKong.
I´ve tried to update it with the new rom from the "sourceO2" page ... the update started and then an error occured... ???
Now I can only see " USB " (when the device is placed in the sync station) or " Serial " (when it´s not) at the upper part of the screen ...
... and " V 2.07 " at the lower part.
What can I do to use my XDA again ???
Please HELP ME!
Thanks in advance!
Joern :shock:
...
by the way ... Of course I don´t have a backup :-(
If you plug it into your cradle, while activesync won't connect, your phone is still connected with your PC. So you can still update the rom through the rom installer.
So I suggest you find another rom and upgrade it, or try the same one again (in hopes something just went wrong during flashing).
First of all thank you for your prompt reply!
I´ve downloaded several ROM´s already ... But I always get the "wrong country ID" message!
Any other tips?
Same Probelm
I got the exactly the same problem with you. Hope someone can help us!
Ken
Or maybe anyone knows where to get the original ROM for my HongKong XDAIIs ?? There were some links in old posts.. But they don´t work anymore :-(
Unless anyone can find the Country ID of your XDAIIs (which you can no longer check because your device is inoperable), I'm at a loss.
POssibilities I've found are:
O2ASI001
O2___001
So all I can suggest is you try the suggestions here with the above (or if you find it, the correct) country IDs and the O2 Roms you have been trying:
http://wiki.xda-developers.com/index.php?pagename=BA_GettingStarted
Sorry I couldn't be any actual help .
HK CHT ?
I have tried to download the file xda2sHKcht.zip on this site in order to try but after I downloaded it, it said that the zip file is corrupted.
where´d you get it? :?:
the download site
on the site "ftp.xda-developers.com/BlueAngel/xda2sHKcht.zip"
user name : xda
password : xda
you can try it and post a response to me to see if it works for you
try my trick with original update from qtek.nu
First download the the file from this link below.
http://www.qtek.nu/files/BA_WWE_BP_12200_169_10602_SHIP.zip
Then extract the zipfile.
After ectracting you get an exe file.
Extract this file also.
Then you get ruu.conf and the other setup files.
edit ruu.conf and add 1 line to it
[CHECKCEID_TYPE]=1
then save ruu.conf
after this start baupgrade.exe.
Hope it works but it only helps with country id error so if device is
differend then we need to do something else.
good luck
Oh if you get error tell me the 5 2digit nrs that appear, i can get device data from baupgrade.exe
There is a table with nrs and providers in it
Thank you for your reply!
I will try that out now. Will inform you what happend!
thanks a lot.
Joern
! ! ! ! ! ! ! ! THANK YOU ! ! ! ! ! ! ! !
IT WORKED!
VASTLOPER - THANK YOU SO MUCH for your TRICK!!
All the others who replied - THANK YOU, too!
KENJAVA - Try that! It worked really perfectly. Even with the newest Upgrade from the O2 page!
The only thing I don´t like about the O2 upgrade is the LOGO next to the start-button, since I´m using T-Mobile and since It´s always in the front and bugging me ;-) ... Anything I can do against it???
Have a nice week!
Joern
Glad it's back alive now.
You can edit some files in the extended rom to remove the logo and the default o2 settings but you must wait till i am home again so i can look it up.
vastloper (naam pas wel bij dit topic ) Denk je dat ik op deze manier ook mijn XDA2s (uit Maleisie) kan updaten?
I think it will as long as it is a PH20B device.
If you ask questions in dutch to me do that in PM please.
People like to be able to understand what is written here so we try to write in english.
vastloper said:
I think it will as long as it is a PH20B device.
If you ask questions in dutch to me do that in PM please.
People like to be able to understand what is written here so we try to write in english.
Click to expand...
Click to collapse
Vastloper. Thanks for the info. Yes it's a PH20B unit.
Sorry about the Dutch.. It's a bad habit.
Here is the question in English: vastloper (name fits to this topic*) Do you also think that I can update my XDA2s (from Malaysia) this way?
* vastloper translated to English means "seize up".
Many people ask me what my name means in english.
Thanks for the translation.
how to edit files in the extended rom ?? :roll:
First unlock extended rom and unhide extended rom with tool found elsewhere on this forum.
You can find it on the ftp under extended rom kitchen in folder tools.
After unlocking you need to reboot the device.
Remove the lines that have to do with O2 in the file config.txt
After changing config.txt you need to mak hard reset.
Good luck.
Hi I've had a search of the forum but could not find the answer to my query. Could anyone tell me how I go about downgrading back to WM5 on my o2 XDa Exec? Thanks in advance guys and girls... this is a great community...
Zac
put it in bootloader and just flash it
no special steps needed, i flashed wm5 from wm6 many times
I am totally newb at this and have no idea how to do that... so would it be too much trouble to ask for a more detailed explanation?
Zac_kha said:
I am totally newb at this and have no idea how to do that... so would it be too much trouble to ask for a more detailed explanation?
Click to expand...
Click to collapse
download the official o2 rom and upgrade...
try google to find the o2 rom
if u are jasjar try the rom at i-mate
I have downloaded the latest rom... but it starts looking for device information... my exec reloads... with WM6 and thats it
1. Put your exec on bootloader mode: Press backlight+power+reset at the same time.
2. Disable your Activesync. Uncheck "Allow USB Connections" under Connection Settings.
3. Plug in ur Exec directly to your PC using the USB cable. (Don't use a USB hub)
4. Flash ROM.
Just wondering? Does flashing the ROM constantly (If done correctly.) hurt anything?
I hope not.. coz if it does.. then my Uni should be very very damaged ryt now. hehe. I've flashed this thing countless times and it's still ok.
maybe just like PC... reinstalling Windows on the desktop PC a thousand times doesn't really do any damage ryt?
yea every sector in the flash memory has an "endurance counter" about roughly how many times it can be erased and re-written before it becoming damaged (bits stuck to 0, or 1, respectively).
although nowadays flash device manufacturers are promising 10000+ EW (erase/write) cycles, I doubt that some devices (especially the NAND chip in the HTC TyTn for instance) comes up to the expectations
DaVince said:
1. Put your exec on bootloader mode: Press backlight+power+reset at the same time.
2. Disable your Activesync. Uncheck "Allow USB Connections" under Connection Settings.
3. Plug in ur Exec directly to your PC using the USB cable. (Don't use a USB hub)
4. Flash ROM.
Click to expand...
Click to collapse
Hello Bro,
Tulong Do u have d original rom for DOPOD 900? Gusto kung e revert sa WM5 na missed ko na yong VIDEO CALL . Maraming Salamat - Lorgem from Singapore
lorgem said:
Hello Bro,
Tulong Do u have d original rom for DOPOD 900? Gusto kung e revert sa WM5 na missed ko na yong VIDEO CALL . Maraming Salamat - Lorgem from Singapore
Click to expand...
Click to collapse
Dude, post in english.
Anyway, you can get the original Dopod 900 ROM on their website.. but I suggest you just use the ROM I'm using. I have the link on my sig.
It has the I-mate boot splash screen... but you can easily change it to anything you want anyways.
Hi all,
i just tried an ROM update on my diamond and ended up with a probably burned diamond.
I tried to updated to "Unsigned-Hard-SPL-Diamond-OliNex" and then to Elite 2.0.
First the Hard-SPL updated didn't work an stoped at 1%.
As i figgured out i had to start the update tool as administrator under my Windows Vista.
The diamond now starts and shows the following screen:
1. A Water like Picture
2. The Text "Xda diamond" in the bottom left corner
3. The Text (in red characters)
R 1.00.25.03
G 52.26a.25.09
D 1.37.00.00
4. The Character "H" (in red) next to the "Xda diamond" Text
The Diamond stops here and does nothing.
I can get to the three colors screen by pressing Vol Down and Reset.
I also tried a hard reset which worked, but i ended up at the same screen and the diamond does nothing and just stops there.
Have i completely damaged my Diamond? (I hope not, would be a nightmare to me)
I will be very grateful for any kind of help on this!
Thanks in advance!
Did u have Flash Hard SPL before?
When u didnt, the Update stops @1% whit err msg like: Wrong vendor ID
Then u have to flash hard SPL before, is sticky in this Forum.
Try maybe with a ROM from here in the first Sticky post, then u can ask for support.
hope helped u
mastah
when you get the "three colour screen" then everything
should be ok, try to reflash the device!
Hi thanks for the quick answer!
I tried now to flash again to the Hard-SPL 1.30... but i get an Error 284 at 0%.
The three color screen shows the following:
DIAM300 MFG 64M
SPL-1.40.LiMex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVI v0x30
Any ideas?
Any help welcome!
I am getting a wrack, my nerves are going crazy. I hope i can recover at least to some ROM now...
Flash hard-spl, set ur device in bootloader mode (tri-color screen. Search for it if u doesent know how)
And flash one of the compatible Roms, they are sticky in the forum.
Maybe urs spl isnt compatible whit the Rom u flashed.
When the Device boot's, and u see the red signs whit numbers, then i think its all ok...
...only incomplete rom.
greets, and good luck
http://forum.xda-developers.com/showthread.php?t=400411
CURRENT ROMS:
RUU_Diamond_hTC_Asia_HK_WWE_1.34.831.1_52.24.25.08 _0.93.25_Ship
RUU_Diamond_HTC_Europe_1.35.401.3_Radio_Signed_Dia mond_52.26.25.09_0.93.25.26_Ship
RUU_Diamond_hTC_Asia_WWE_1.37.707.1_Radio_Signed_D iamond_52.26a.25.09_1.00.25.03_Ship
RUU_Diamond_HTC_WWE-ME_1.37.456.2_Radio_Signed_Diamond_52.26a.25.09_1. 00.25.03_Ship
RUU_Diamond_HTC_SPA_1.37.412.2_Radio_Signed_Diamon d_52.26a.25.09_1.00.25.03_Ship
RUU_Diamond_HTC_Europe_1.37.401.3_Radio_Signed_Dia mond_52.26a.25.09_1.00.25.03_Ship
RUU_Diamond_HTC_NOR_1.37.409.3_Radio_Signed_Diamon d_52.26a.25.09_1.00.25.03_Ship
DIAM1.37.413.3SVE (REBUILT)
COOKED ROMS:
ALL BEPE ROMS ARE SIGNED AND ARE PART OF THE ELITE TEAM ROMs DIVISION, SEE INDIVIDUAL THREADS.
Elite 2.0
PDAVIET DIAMOND_1.37.08.01
tlr-diamond-1.08.06.20
tlr-diamond-2.08.07.01
DIAM.DAN.137.403.3-Cyphol
DIAM140 (EDGE Only Diamond):
indian_ship_rom
http://forum.xda-developers.com/showthread.php?t=400402
Hard-SPL or how I learned to stop worrying and love the MPU
If this not work try with spl dev-edition:
http://forum.xda-developers.com/showthread.php?t=400950
thanks for the suggestions.
i will try what you said and see what i can get.
thanks really much for your help this forum is amazing!
hope i can finally live again with my diamon which i already like so much...
thanks again!
ur welcome.
and another tip:
Try to flash on XP
at the momen seems easyer to flash from linux as from Vista
I can feel ur pain
thanks mashta,
i will try it on vista 32 first, since i do not have xp here
thanks again for all the help!
On Vista 64, I had to take the following steps to have it working:
Fisrt: connect the device in boot mode to the PC
Second: wait until Vista installs a driver update
Third: disconnect the device and restart the PC after the update is installed
Forth: right-click on the RUU executable, and choose
compatibility mode with Win XP SP2
Fifth: run the RUU, cross your fingers and start praying
As how to enter bootloader, press volume down and reset simultaneously
s1rl4ncel0t
Senior Member
mastah said:
ur welcome.
and another tip:
Try to flash on XP
at the momen seems easyer to flash from linux as from Vista
I can feel ur pain
Click to expand...
Click to collapse
I had no problem flashing to Unsigned Hard-SPL (1.4?) and bepe's bElite 0.54 Basic ROM using Windows Vista Business x64 (SP1).
It worked out of the box, without any special drivers installed whatsoever. I believe there were some drivers installed when I got it into bootloader mode, but aside from WMDC I didn't install any extra software
Milenco said:
I had no problem flashing to Unsigned Hard-SPL (1.4?) and bepe's bElite 0.54 Basic ROM using Windows Vista Business x64 (SP1).
Click to expand...
Click to collapse
Lucky boy, but many peoples has probs whit vista
and maybe it helps to try on a other os to find
whats the bug
and helpfull site:
http://www.modmydiamond.info/
sounds like a bad flash? i once had the same problem with HTC tytn2, and i managed to contact forumer GSLeon who helped me out. he said "after a bad flash,u should never keep attempting to flash again, because u may permanently brick your phone"
THANK GOOD IT WORKS AGIN!
And now the asnwer what was the problem:
A ****ing USB-HUB from MSI!
I had my diamond connected throu that USB hub and so everytime i tried to flash i had communication errors at 0% or 1%.
I connected the diamon directly to my pc and guess what:
It worked like a charm.
THANKS AGAIN TO ALL THE HELP FROM PEOPLE HERE!
This forum is realy amazing.
Thanks again very very much!
I am so happy to have my diamon back
And i will never buy a MSI USB HUB again...
A Happy Ending after all......
I bet your so releived and I bet you've learnt a lot too!
Blob8me said:
A Happy Ending after all......
I bet your so releived and I bet you've learnt a lot too!
Click to expand...
Click to collapse
Releived is not the right word, back to life fits more
Thanks again for all the help i have got here!
davidl said:
And i will never buy a MSI USB HUB again...
Click to expand...
Click to collapse
Just so that in a few weeks time when someone else searches and finds this thread.........
NEVER US ANY KIND OF HUB TO FLASH A PHONE, ALWAYS PLUG THE PHONE DIRECTLY INTO YOUR MOTHERBOARDS USB SOCKET
Oh and davidl you are one lucky son of a *****
people could read a bit more before trying to help - the guy obviously had the hardspl flashed because of the version that was reported in tricolour. (1.40.etc...though it was mistyped )
anyway good that it got resolved OK. using hubs is indeed not recommended.
welcome to the darkside of the diamond
hi guys
i'm just beginnin' and talkin' to you from my diamond an' my ****in' orange french default rom the 1.73.73.2
so for those who know that it was made by sons of *****es for their bros,
i was going crazy to about this problem but you guys are really marvelous an' think know that i have the answer to my problem.
but i'm a new bee as you can see and i'd like to know if i have to install anyway hard spl?
i just want to delete this ****in' rom...
excuz me for my english and one million thanks for that precious help
3 ... 2 ... 1... Ooooh he got banned!
hi to all ... please to answer at one question ..... i search the internet yesterday and today and i read a lot of tutorials from wich i learn a lot of things about how work this awsome device .... it's my first htc and my first windows mobile phone and i'm proud of my choice ( but this is another story )
..... my diamond have a branded ROM , a vodafone one , and i want to install a new ROM - WWE 7.5 FULL ..... especially i want to change the language , because now is german , i'm roumanian , and i want english on it : )) ... well done i downloaded all necessary files to start the job ..... but my enthusiasm was knocked-out because i meet the next screen ( see the photo )
so....what should i do ? and what am I doing wrong ? ... i follow conscientios all the instructions :
- battery is full
- usb cable is well connected to PC and Phone
- standby and hibernate modes are turned off
- i have a correct ActiveSync connection between Phone and PC .... including Outlook
so if you will tell me what to do i will be verry gratefull
thanks in advance
have u downloaded and flashed the hard spl? if not do it...
see this http://forum.xda-developers.com/showthread.php?t=416211
i just attach a photo....the problem was because the server don't let me , as a new user , to atact an external link to a photo sharing site .... excuse me for this mistake
this is the step where i remain...the first step....i was'nt able to pass hard spl
uhmmm i never saw this error...
Put it in bootloader mode and try again
and how can i put my diamond on bootloader mode ? ..... by pressing volume down and reset keys in the same time ... and will appear a screen with some text informations and 3 different colors ?..... I do this few hours ago and then i lose a lot of time to do my phone work well again ...are you sure is this exactly what i need to do ?
sorry for this words , maybe you are an experienced member of this comunity and you don't deserve this , but i want to be sure
use internal storage method...is easy...in the rom you download there is a file .nbh rename it to diamimg.nbh then copy in the root of the internal memory
soft reset then hold the back button and the vol down button...follow the instruction on screen...and if you want do a hard reset after...simply soft reset then vol down + central pad button...follow the instruction..and you'll be ready
Salutare...
Salut ...id ul meu de mess este t_john87 ...adauga-ma si te invat eu cum sa-l instalezi..si ti recomand si o versiune buna de rom..eventual ti-l dau prin messenger...depinde ce vrei..in engleza...romana...6.1 ..sau 6.5 ..bafta
BladeIonut94 said:
hi to all ... please to answer at one question ..... i search the internet yesterday and today and i read a lot of tutorials from wich i learn a lot of things about how work this awsome device .... it's my first htc and my first windows mobile phone and i'm proud of my choice ( but this is another story )
..... my diamond have a branded ROM , a vodafone one , and i want to install a new ROM - WWE 7.5 FULL ..... especially i want to change the language , because now is german , i'm roumanian , and i want english on it : )) ... well done i downloaded all necessary files to start the job ..... but my enthusiasm was knocked-out because i meet the next screen ( see the photo )
so....what should i do ? and what am I doing wrong ? ... i follow conscientios all the instructions :
- battery is full
- usb cable is well connected to PC and Phone
- standby and hibernate modes are turned off
- i have a correct ActiveSync connection between Phone and PC .... including Outlook
so if you will tell me what to do i will be verry gratefull
thanks in advance
Click to expand...
Click to collapse
i have sppl 1.93 0000 and i try all the tutorials finded on xda about how to change to 1.93 signed by olinex and every time i get an error and when i went for a tutorial to solve that error i face another obstacol ....it seems like my last chance to change that damn sppl version is to use something called NBHUtil ... but i don't understand very well how it works so if someone will be so gentil to explain me in details this "easy" procedure this will be my last question
please post a solution and thanks in advance
LE : i learn how nbhutil works and still no result ... what else can i try to change this damn spl because i'm sick of vodafone branded windows and it's german language ... ...my diamond is Diam 100 so it shouldn't be so hard to "work" with it... but it seems like nothing want to work
hello,
i've got a Mda compact 3 (t-mobile)
ipl 3.15.0001
spl 3.15.0000
gsm 02.92.90
os 3.15.0.0
sinds yesterday it gives me the message:
Device start up failed due to sudden loss of power.
i've tried hard reset, format etc butt still get the message
now i found a posttread that should do the trick
get it in to booloadermode and flash it with a official rom
butt i cant find on the net
a original Dutch/nl rom ...
does somebody has it ...can you please post it
dutch trans.
Orgineel Mda compact 3 gezocht
je zou mij erggg blij mee maken
did u even upgrade it before with a new rom?
ive never seen the sudden loss of power message...
mvenneker said:
did u even upgrade it before with a new rom?
Click to expand...
Click to collapse
my litle brother had it for a couple days dont know
what he's done with it.
i hope in someway i can fixed it
butt first i most try to putt in someway the original nld rom back
do you maybe have a link or advice?
can somebody help me with my problem
hope this helps
http://rapidshare.com/files/94476422/HTC_P3300_NLD_3.13.404.1_4.1.13.44_02.94.90_Ship_R.exe.html
i've tried it
but after 2 % it stops with message
ERROR Invalid model (244)
(thnx for your reply (sheenick)