hi,
Few days ago I did update on my r500 to R500XXU1GVG1 and watch keep randomly crashing and freezing and have to reboot or let baterry discharge ... and start it again.
Before update was working fine.
Does anyone have previos version of soft which was R500XXU1GUJ2 ? ( and eventually instruction how to downgrade?)
thanks
Any other solutions for issue with my watch? I also noticed it is still on however screen is black and do not respond to holding both buttons (restart), I know watch is ok as it is connected with phone.
Related
Hey everyone.
I'm really hoping someone can help me with my Huawei P6 Ascend.
For the last 2 days, my phone goes into a reboot cycle or switches off every time its on standby. When I'm using the phone (or when the screen is on) or if the screen is off, but I'm playing music, the phone is fine. But every time I press the sleep button on the side or the screen goes off normally, the phone either restarts itself, or switches off completely. It restarts or switches off within 30 seconds of going into standby, which is VERY frustrating.
I booted in safe mode, did a factory reset, and even installed the Chinese version KitKat OS. After Installing Kit Kat, the phone no longer restarts, it now just switches off completely once it goes into standby.
Does anyone have any suggestions for what I should do next?
Some other useful info:
- It started rebooting after I used the google maps app. I read that Jelly Bean sometimes rebooted when using GPS, so thats why I installed KitKat.
- Every time it would reboot in Jelly Bean, it would start in airplane mode. Now, with KitKat, it just switches off and I have to manually start it, but it doesnt start in airplane mode.
Please please help!
tallen-za said:
Hey everyone.
I'm really hoping someone can help me with my Huawei P6 Ascend.
For the last 2 days, my phone goes into a reboot cycle or switches off every time its on standby. When I'm using the phone (or when the screen is on) or if the screen is off, but I'm playing music, the phone is fine. But every time I press the sleep button on the side or the screen goes off normally, the phone either restarts itself, or switches off completely. It restarts or switches off within 30 seconds of going into standby, which is VERY frustrating.
I booted in safe mode, did a factory reset, and even installed the Chinese version KitKat OS. After Installing Kit Kat, the phone no longer restarts, it now just switches off completely once it goes into standby.
Does anyone have any suggestions for what I should do next?
Some other useful info:
- It started rebooting after I used the google maps app. I read that Jelly Bean sometimes rebooted when using GPS, so thats why I installed KitKat.
- Every time it would reboot in Jelly Bean, it would start in airplane mode. Now, with KitKat, it just switches off and I have to manually start it, but it doesnt start in airplane mode.
Please please help!
Click to expand...
Click to collapse
Havent you tried deleting the google map app yet ?
Well, the KitKat version doesn't have any GAPPS, and its still doing it...
The same problem
help plss
I have same problem .. any one know is it heardwire or virus problem. I lost all data in the phone. It seems the reset switch is btokem and making it on and aff all the time . Phone become hot also.
Hi there, first of all I've seen some other threads which kind of have the same problem but not quite. So here is my problem my touch screen isn't responding most of the time, it started happening like a week ago when it froze while trying to send a picture in messenger, after 1-2 reboots it started working again but after that the same thing happened while I was typing in messenger, so I thought it might be software problem and made hard reset and installed new stock android(that didn't help). The last couple of days most of the time it's not working and I'm using it with a mouse, but there are periods when it works for some time. I've entered the hidden menu(without updating the touch firmware because I saw that it might kill it for good) to try and test it and had 2 different results
- The touch screen firmware version on my phone is -1
- And the one from the photos that I've attached(obviously during this one it actually worked for a couple of minutes)
Something else I've noticed while the touch isn't working when I turn off the screen from the power button first it dims the light for 2 seconds before really turning off.
Other things that I've tried are changing kernel, opening the back of the phone and reconnecting the screen to the motherboard(which helped the first time and it worked for 1 day or so but doesn't help since then) .
There is one more strange thing for some time now may be 3-4 months the phone has problems connecting to WiFi)
And one last thing after the screen problem the phone started booting quite slow some times and showing "Process System Not Responding'"
The phone is running on Stock V30b MM and hasn't been dropped for a long time
The problem is that I don't know is it software problem, screen problem or motherboard so any Ideas will be appreciated.
Hi All, I'm new to XDA. I bought my LG Nexus 5x in 2016 (July). Since last week my phone isn't working. This is what happens.
When I switch on the phone after full charge. It starts with a very small white light ,but no display (no logo , nothing).
There is a welcome password at the start. So it will not go to any other step. I couldn't type my password , because nothing on the screen. But when I try to press on the screen , I can feel the keyboard touch.
I alos tried changing the display with another working 5x display. But same issue. Any suggestions guys?
PS : I didn't update this to Oreo. But before this issue happened , there was an auto update of Google Play Service with 430 MB (I also cancelled auto update ,didn't know how it was updated without my permission) , after that Oreo update notification wasn't in notification panel. But when I was checking at Setting OS wasn't updated to Oreo at that time
Alright so this exact thing happened to me few months back. I bought new phone and moved on. So like 20 minutes ago, I got the urge to check on my nexus if it can be revived and surprisingly, the screen started working. I don't know how, but the screen was totally black before i gave this phone up (with backlight on) and I could feel the vibrations. Just a few minutes ago I have started seeing these screen distortions again. I think it's a software issue so i'm downloading latest 7.1.2 ota to flash and will apply bootloop fix and see if it fixes anything.
AngelousJi said:
Alright so this exact thing happened to me few months back. I bought new phone and moved on. So like 20 minutes ago, I got the urge to check on my nexus if it can be revived and surprisingly, the screen started working. I don't know how, but the screen was totally black before i gave this phone up (with backlight on) and I could feel the vibrations. Just a few minutes ago I have started seeing these screen distortions again. I think it's a software issue so i'm downloading latest 7.1.2 ota to flash and will apply bootloop fix and see if it fixes anything.
Click to expand...
Click to collapse
Hi, Thank you very much for kind reply. I don't understand the last part. Did you resolve the issue? Did you flash the device? Please help me with the steps that you have followed.
Hey everyone,
couldn't find a topic about this yet so here I am. I recently got a Mi A2 lite and happily unlocked it, rooted it and so on. Worked perfectly fine till yesterday. Then suddenly it started to freeze. Meaning the fingerprint sensor didn't have any reaction anymore. I couldn't use the screen anymore either. I was able to start the screen by pressing the power button once, it was also possible to press it twice to start the camera or keep pressing it to show the restart menu or forcefully restart it, but no matter what I did I couldn't interact with anything on the screen. So I had to forcefully restart the phone and then it was working fine again until some time later.... I've had it like 6 times in 90 minutes so I decided to make a clean install and see what happens. Rooted the phone again and it was the same once again... Didn't change anything.
Now I locked my phone again (getting ready to send it back) and will try "stock" and see if the root has anything to do with it.
My guess is that it's a hardware problem but before I send it back I wanted to check if anyone here has another idea or solution.
Thanks in advance
Edit: Stock isn't working either, error still happening. I'm returning it.
Hello guys
Recently got a watch fit that's running 1.0.2.12
On the health app it says that 1.0.3.20 is available. But when I run the update it gets downloaded to the phone, transferred to the watch and when it starts to install it reaches 68% the watch restarts and stays on its old firmware.
I factory reset it through the app and watch. Deleted data and cache from the app. Got the latest version of the health app even installed HMS and updated to the latest. Installed app gallery just to check that I had the latest health app. Done it off charge at 100% battery and even while it's plugged. Nothing seems to work.
Weird thing I don't get any error, it just restarts at 68% everytime.
Anyone got a clue or faced the same issue?
I have the same problem
belkacemi_sa said:
Hello guys
Recently got a watch fit that's running 1.0.2.12
On the health app it says that 1.0.3.20 is available. But when I run the update it gets downloaded to the phone, transferred to the watch and when it starts to install it reaches 68% the watch restarts and stays on its old firmware.
I factory reset it through the app and watch. Deleted data and cache from the app. Got the latest version of the health app even installed HMS and updated to the latest. Installed app gallery just to check that I had the latest health app. Done it off charge at 100% battery and even while it's plugged. Nothing seems to work.
Weird thing I don't get any error, it just restarts at 68% everytime.
Anyone got a clue or faced the same issue?
Click to expand...
Click to collapse
I have the same problem, did you find any solution?
Estenislausp said:
I have the same problem, did you find any solution?
Click to expand...
Click to collapse
Nope nothing yet. I got my hands on the firmware. I'll have a look into it and see if I can figure something out
Any luck ?
belkacemi_sa said:
Nope nothing yet. I got my hands on the firmware. I'll have a look into it and see if I can figure something out
Click to expand...
Click to collapse
Any Luck?
rui.salome said:
Any Luck?
Click to expand...
Click to collapse
Nothing yet. The firmware is lzma compressed with blowfish ciphered parts. All I could get is the Huawei BMP image for now. Does it stops at 68% on your unit too?
belkacemi_sa said:
Nothing yet. The firmware is lzma compressed with blowfish ciphered parts. All I could get is the Huawei BMP image for now. Does it stops at 68% on your unit too?
Click to expand...
Click to collapse
Yes, stops at 68%... i tried everything !!
i had this problem and tried everything even contacted Huawei but they didnt know how to fix it
the solution is simple when installing reaches 68% press the side button until the watch power off then when you start the watch update will install again , then when the installation reaches 68% keep pressing the side button repeatedly untill the installation passes the 68% and keep pressing it again if it stuck at any other percentage , i hope this solution works with you
palkarate said:
i had this problem and tried everything even contacted Huawei but they didnt know how to fix it
the solution is simple when installing reaches 68% press the side button until the watch power off then when you start the watch update will install again , then when the installation reaches 68% keep pressing the side button repeatedly untill the installation passes the 68% and keep pressing it again if it stuck at any other percentage , i hope this solution works with you
Click to expand...
Click to collapse
Thanks for your reply. Well actually the update doesn't get stuck or anything. It goes just fine until it reaches 68% the wheel keeps turning and then the watch reboots itself
belkacemi_sa said:
Thanks for your reply. Well actually the update doesn't get stuck or anything. It goes just fine until it reaches 68% the wheel keeps turning and then the watch reboots itself
Click to expand...
Click to collapse
yes this was my problem it reboot after 68% , i managed to fix this by these steps when it reach 68% try to shut down the watch by pressing the side button about 30 second then start the watch it will start installing again once you start it , the when the installation reaches 68% keep pressing the side button repeatedly until it passes the 68%.. this worked after this i had about 3 major updates without any problem
palkarate said:
yes this was my problem it reboot after 68% , i managed to fix this by these steps when it reach 68% try to shut down the watch by pressing the side button about 30 second then start the watch it will start installing again once you start it , the when the installation reaches 68% keep pressing the side button repeatedly until it passes the 68%.. this worked after this i had about 3 major updates without any problem
Click to expand...
Click to collapse
I've tried just that. It did shut down and start installing again, I kept pressing the button it rebooted again. I'll give it a couple more shots and see what comes out, I might've not pressed enough
belkacemi_sa said:
I've tried just that. It did shut down and start installing again, I kept pressing the button it rebooted again. I'll give it a couple more shots and see what comes out, I might've not pressed enough
Click to expand...
Click to collapse
If it helps i kept pressing fast try to reset the watch and reinstall the latest health app then redo these steps
Some problem here. When I reach 46% it is restarting imediatly. On my watch, it is not stuck at 46% .....when the installation reach 46% , in a second it is restarting.
I try the above method . It is working only if I press VERRY rapidly the side button; and I managed to update. I press this button like 3 minutes until the install finish.
Next updates works normal!
Mine still stuck at 1.0.3
catelusii said:
Some problem here. When I reach 46% it is restarting imediatly. On my watch, it is not stuck at 46% .....when the installation reach 46% , in a second it is restarting.
I try the above method . It is working only if I press VERRY rapidly the side button; and I managed to update. I press this button like 3 minutes until the install finish.
Next updates works normal!
Click to expand...
Click to collapse
Mine still stuck at 68%... even doing the method described. Need some help here !!
What do you mean by, "press this button like 3 minutes"? You reach 46% and then press the side button for 3 minutes?
palkarate said:
If it helps i kept pressing fast try to reset the watch and reinstall the latest health app then redo these steps
Click to expand...
Click to collapse
You keep pressing the side button for the whole update process?
Hi Guys,
I still have the problem. I have tried the method described above several times, but there is no solution, the problem persists. Any other solution?