Samsung S20 problems with UV glue - Samsung Galaxy S20 / S20+ / S20 Ultra Questions &

Hey guys,
Recently I applied the UV tempered screen protector on my phone which had to be removed after tampering it. However, I applied a second screen protector (same type) and after the applying process i saw the glass quite separated around the top right corner as well as the power button came out as the rubber and the plastic holding it was quite dissolved, like it looked like it's worn off.
Now my phone's like 5 months old and there's no way that would happen, so I think it probably is due to the UV activated glue leaking through the button.
My speakers were fine, as well as the microphone is working as of now ( 5 hours after the application). The power button works fine as I put it back in and put my cover over it, however it keeps falling off without the cover as the rubber and plastic parts are broken in it. So I called the authorized repair center and they mentioned that they do not just replace the button, they have the whole set as in the frame and display which was very expensive, hence, I can't afford it right now.
I just wanna know if any of you guys here got any experience with the UV glue leaking to internals of a phone? I'm worried that it might cause damage to the circuit boards and other stuff inside and my phone might be unusable in a few days... Do such things happen?

Related

Broken LCD Screen, replaced it, now touch doesn't work

OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.

*** Need help with cracked screen***

***Need help*** with broken/ cracked screen on my vibrant. Anyone here know how to replace and where to buy a screen. Touchscreen still works fine, but I have 2 vertical cracks down the phone and 2 across horizontally. Please help.
Vibrant ROOTED and on TOXIC CRACK
try repairs universe
also there is a youtube video on how to do it
I also cracked mine some time ago. The kits sold on ebay is fine. It includes amoled+gorilla glass, because amoled is so thin that it is impossible to sell it independently. There are several videos on youtube. It is not a hard replacement, I'm sure you can do it yourself. Just disassemble it and after removing mainboard, you remove data bus of the screen, then connect the new screen's data bus. Mine works perfect
I replaced my broken screen but it is not easy. The youtube videos make it look easier than it is. Besides a 2 mm phillips and a pry tool, you will need tweezers, strong reading glasses, something like rubber cement because the screen is really just glued in there, good lighting, and a lot of patience. I have worked on laptops and this is harder.
Once you figure out that the front bezel isn't designed to hold the screen in, it becomes a bit less frustrating but it took me about three hours and lots of scraping of little pieces of broken screen glass out of the front bezel frame. It's back together but I must have gotten the microphone in backwards because it doesn't work, or maybe a wire pulled off the mic. The supplemental menu button in the lower left hand corner does not work either. .
Do yourself a favor and buy a new phone, the AMOLED+Gorilla glass is like 75% of the total cost. Gorilla glass is cheap about $25 but it is extremly hard to replace. at least it is very difficult to remove without inflicting any damage to the phone or the AMOLED. If you go for it. you can use heat to soften the adhesive but be careful that AMOLED is extremly fragile on its own and the touch screen can get easily burned.
After looking on Global Direct, it seems the eBay screen replacement kits don't include everything you need. The phone originally uses die cut adhesive stickers instead of glue to keep the screen in. Screens can be had for $100-$120, less than the phone, but the lower button - mic assembly flex-pcb seems prone to being screwed up 'cause my lower left button and mic won't work now. My screen was pretty well crumbled especially around the lower buttons and perhaps it was just unavoidable that I damaged the lower button mic pcb trying to scrape the glass off.. A new pcb costs around $40 and that is getting up to the price of the phone. Still, being able to successfully disassemble the phone and know how it works could be useful. Some people might be clever enough to upgrade stock parts like putting in a better mic, arctic-silver-epoxying a thin sheet heatsink to the cpu to aid in ocing, etc. The new screen did not break and looks pristine, though, it's just that I f**ked up something else putting it in.

[Q] Touch screen issues after replacing glass

I broke my screen a while ago, and decided recently to go ahead and change it myself. I ordered a glass for 10$ on Ebay and when it arrived, I followed a tutorial on Youtube where I had to heat the front of my phone, then with a knife or something sharp lift the glass, then put the net one after I was sure everything was properly cleaned.
The problem is my screen was so shattered in some places that it was really hard to remove everything so I ended up applying more pressure on the AMOLED to remove the remaining glass pieces.
So I cleaned it afterwards, and placed the new one. Booted, and VICTORY, everything works... Or so I thought.
I noticed my touch screen now behaves oddly. For example if I type too fast it will miss some letters. If I press to hard on the screen it will become like it's completely unbalanced, registering toush inputs anywhere until I close I turn the screen off and back on.
If I try to draw on the screen (in Draw Something, for example) it won't be accurate, to the point I can't really play the game anymore.
My question is : do you think I broke something when applying heat (I didn't apply that much so I don't think so) or when removing the hard-to-remove last glass pieces? Or did I simply made some mistake when replacing the glass and it's not correctly in place (I noticed it's a little higher relatively to the bezel, compared to what it was before)? Maybe it's not perfectly in place...
Thank you for your advice! I'm a noob hardware-wise so I have no idea at all what's the problem!

Screen easy to broke?

Hello everyone,
Is it just me or the new M8 have a fragile screen? I've had quite a lot of HTC phone in the past and never had a scratched/broken/cracked screen with any of them (they had invisible shield but it still was very clear). But my M8? A different story. My first one last 1 month before cracking near the middle on the left. I changed it and immediatly (as in remove from the box and install) an invisible shield glass. Now, the protector, 8 weeks old, is cracked at 4 places.
The phone never droped or hit anything and is alone in my pocket, far from anything, like all of my other phone... Is it because it's bigger then the other, thus making it "warp" in my pocket, adding pressure on the screen? I don't know, but I really feel like I'll be forced to by a case with front flap to prevent that, something I really wanted to avoid.
nodiaque said:
Hello everyone,
Is it just me or the new M8 have a fragile screen? I've had quite a lot of HTC phone in the past and never had a scratched/broken/cracked screen with any of them (they had invisible shield but it still was very clear). But my M8? A different story. My first one last 1 month before cracking near the middle on the left. I changed it and immediatly (as in remove from the box and install) an invisible shield glass. Now, the protector, 8 weeks old, is cracked at 4 places.
The phone never droped or hit anything and is alone in my pocket, far from anything, like all of my other phone... Is it because it's bigger then the other, thus making it "warp" in my pocket, adding pressure on the screen? I don't know, but I really feel like I'll be forced to by a case with front flap to prevent that, something I really wanted to avoid.
Click to expand...
Click to collapse
You've invested in this Awesome phone, but you don't want to spend money to protect it? Personally I bought an otterbox. These days one hast to have a protective case, as all the newer phones screens are fragile. I am glad the rep at the T-Mobile store talked me into getting the case. I have a bit more peace of mind now. If you get a case I highly recommend an otter case, I don't think there is a case better than an otter case, then again this is the first time I have bought a case for my phone so I could be wrong.
Hmmm... Haven't had a case since one x, gorilla glass are suppose to be tough and I like the aluminum finish on the phone. M7 didn't had this issue neither. Right now I'm waiting for my invisible glass replacement, but still, this phone never dropped, never bump on something, always rest on his back and still, screen broke. It's super fragile and it shouldn't be like that
Never had this problem at all. I hammer my phones too. I've dropped it numerous times, and it has marks and chips in the aluminium and two very small scratches on the screen.
Nothing at all fragile about this phone or the screen, although you said the screen protector shattered too so it's something you are doing.
I really don't see what I'm doing differently then with all my other phone. It's in my pocket, screen side on my skin so if it bump, it bump the back, always rest on his back, never droped or bumped.... The first one cracked from the middle of the screen (left to the middle), this one, the screen protector cracked from the top middle to the right. Really weird...
nodiaque said:
I really don't see what I'm doing differently then with all my other phone. It's in my pocket, screen side on my skin so if it bump, it bump the back, always rest on his back, never droped or bumped.... The first one cracked from the middle of the screen (left to the middle), this one, the screen protector cracked from the top middle to the right. Really weird...
Click to expand...
Click to collapse
Perhaps it's getting twisted from being in the pocket. The phone is quite tall, so when it's in your pocket and you move around, it could put stress on the phone and make it crack. For instance when you sit down and your pants gets stretched out etc. I've broken the volume buttons of another phone by keeping in the pocket while im on a bike, and in time the stress on the buttons caused them to malfuntion.
That's the only explanation i can think of, when you say that you haven't dropped it and it hasn't bumped into anything etc.

replacing screen from zenfone 2 551

Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
pulesky said:
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
Click to expand...
Click to collapse
Seems pretty easy, please check these videos:
https://www.youtube.com/watch?v=qMIivqu6XJY
https://www.youtube.com/watch?v=v4HZt3Aadsc
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
dodongobongo said:
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
Click to expand...
Click to collapse
Try using a hair dryer on the battery for a minute, but keep moving the hair dryer up and down, to spread the heat all over, this should make the glue soft enough to make it easier to peel the battery off.
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
dodongobongo said:
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
Click to expand...
Click to collapse
Just cracked my phone. :crying:Thanks for the instructions. Before I decide to do this, are any of the adhesives necessary to put the phone back together?
Yes, order some double-tape for cellphones.
Glad I'm not the only one that succeded althought I scrapped the battery in my case .
I followed mostly the same steps but for anyone that want some pictures, I posted them in another thread
http://forum.xda-developers.com/zenfone2/help/q-lcd-replacement-procedure-t3135165
Can asus ze550ml screen will fit to ze550kl model
@Ptselv: probably best to start a new thread rather than hijack one that is several months old.
And to answer your question: No, a ZE550ML screen will not fit a ZE550KL phone. My suggestion: search AliExpress.com for "ze551kl digitizer" and you'll be likely to find what you need.

Categories

Resources