Related
Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much
I had to do hard reset about 3 times when upgrading my hx2490B.
f1xxx3r said:
Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much
Click to expand...
Click to collapse
I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?
Some people say that removing the battery for 24 hours may help.
Try that.
When i flashed my 2490 i did format the device and than did the flash.
But I don't think that matters cause the first time when i did flash i didn't format the drive and it was OK.
f1xxx3r said:
I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?
Click to expand...
Click to collapse
I'll remove the battery then and see tommorow. The main question is: is my device completely dead or is it "resurectable" ? I don't think that it need servicing .... but ... just asking
Thank you for the replies. If the batterry removal fix works I'll post here. In the meantime any other possible sollutions are welcome.
My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?
Just an idea (since I had to do this yesterday) maybe try formatting the device.
After flashing 4PDA ROM to my device it would get stack on the same screen as yours. After formatting it all went OK and I had WM6.
For my device I had to click calender + power + messaging + reset, release reset - release all.
f1xxx3r said:
My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?
Click to expand...
Click to collapse
It's still dead....
It's back. P.S. Format did the trick
Same problem
i have " HP IPAQ hx2410 " with WM2003 CE 1.10.0 and i upgraded with this window 5.2 it upgraded successfully but i m stuck on the first loading screen. its stuck when loading complete i have tried every thing such as boot-loader thing and also cant downgrade it . . . so kindly plzzz any one tell me how can i go to my initial state on wm2003 ASAP.
WHAT IS P.S. Format ??? and how can i do that . . .
The answer is here:
http://tinyurl.com/2d4cza7
Hi guys,
I have a problem with my firetv where it won't boot past the Amazon logo. This happened after restarting the system when I installed firetv Boot Menu.
Any help would be welcomed
Sorry I'm not likely to have a fix, but are you sure you unlocked boot loader before attempting to install the boot menu? This could be the cause for the brick.
Are you able to boot to recovery? If so you might be ok. I VERY TENTATIVELY say that if you can get into recovery from there either a factory reset or reflashing a prerooted fw might help BUT if you're able to get there PLEASE don't proceed till someone with more experience chimes in!
I will say that there's hope if you can get to recovery... probably? But this never happened to me.
Have you tried restarting with usb keyboard attached and pressing the print alt screen? Good luck.
Phill360 said:
Hi guys,
I have a problem with my firetv where it won't boot past the Amazon logo. This happened after restarting the system when I installed firetv Boot Menu.
Any help would be welcomed
Click to expand...
Click to collapse
hi,
I am not an expert on this matter but you should provide detail info exactly what you did to your Fire TV, the exact steps and sequence so folks can help you better.
In the meantime, check these all link out before you do anything. It seems few folks has some success see link 2 and 3 as always try it on your risk. I hope someone else can provide a better solution.
http://www.aftvnews.com/top-ways-to-brick-your-fire-tv/
http://www.aftvnews.com/how-to-unbr...ry-mode-and-factory-reset-the-amazon-fire-tv/
http://forum.xda-developers.com/showthread.php?t=2799779
http://www.aftvnews.com/factory-reset-on-amazon-fire-tv-and-fire-tv-stick-explained/
btw, if you are using amazon fire tv for xbmc as it seems most folks are using it for, i would just get Raspberry PI, it is awesome never had to worry about bricking the damn thing, sure it slower than fire tv but i have use it and i love it, it plays 1080 and 3d movies and no buffering either.
I also fire tv but i am always scared this thing will brick as it seems many folks have this problem.
Thank you
KLit75 said:
Sorry I'm not likely to have a fix, but are you sure you unlocked boot loader before attempting to install the boot menu? This could be the cause for the brick.
Are you able to boot to recovery? If so you might be ok. I VERY TENTATIVELY say that if you can get into recovery from there either a factory reset or reflashing a prerooted fw might help BUT if you're able to get there PLEASE don't proceed till someone with more experience chimes in!
I will say that there's hope if you can get to recovery... probably? But this never happened to me.
Have you tried restarting with usb keyboard attached and pressing the print alt screen? Good luck.
Click to expand...
Click to collapse
Thanks for the reply Klite, I didn't unlock the bootloader before installing the menu so that must have caused the brick.
I'm only able to see the Amazon logo, it does not reach the Fire TV Logo. I have plugged in a USB keyboard but i can't seem to get to recovery.
ashsha7877 said:
hi,
btw, if you are using amazon fire tv for xbmc as it seems most folks are using it for, i would just get Raspberry PI, it is awesome never had to worry about bricking the damn thing, sure it slower than fire tv but i have use it and i love it, it plays 1080 and 3d movies and no buffering either.
I also fire tv but i am always scared this thing will brick as it seems many folks have this problem.
Thank you
Click to expand...
Click to collapse
Hi Ashsha
I do mainly use my FTV for Kodi, I did previously use a Raspberry Pi but i bought this to replace it as i wanted something more powerful due to the problems i was having with stutters during play back.
Thanks for the links too, i did try them but i have had no luck so far.
Does anyone know if it possible to unbrick my FTV via USB using Fastboot or ADB?
Phill360 said:
Hi guys,
I have a problem with my firetv where it won't boot past the Amazon logo. This happened after restarting the system when I installed firetv Boot Menu.
Any help would be welcomed
Click to expand...
Click to collapse
Phill360 said:
Does anyone know if it possible to unbrick my FTV via USB using Fastboot or ADB?
Click to expand...
Click to collapse
That's a very good question. I know it's pretty much essential to unbrick a kindle fire but can't find any info specific to aftv. But you're motivation to get an answer is greater than mine. Do you have one?
I'd be confident in trying it with a phone or tablet but I just don't know enough about the variables (like could you do more damage sending power to somewhere that has an external power source)
My best advice is to be patient, keep looking for possible fixes online, but I'd caution not to experiment. Instead keep coming back here to get thoughts on possible fixes that might work. At the very least your thread will stay high in the forum search results giving you a better chance of having the right xda member to notice it.
KLit75 said:
That's a very good question. I know it's pretty much essential to unbrick a kindle fire but can't find any info specific to aftv. But you're motivation to get an answer is greater than mine. Do you have one?
I'd be confident in trying it with a phone or tablet but I just don't know enough about the variables (like could you do more damage sending power to somewhere that has an external power source)
My best advice is to be patient, keep looking for possible fixes online, but I'd caution not to experiment. Instead keep coming back here to get thoughts on possible fixes that might work. At the very least your thread will stay high in the forum search results giving you a better chance of having the right xda member to notice it.
Click to expand...
Click to collapse
If you didn't follow the directions and didn't unlock, then it is bricked and the only way to fix it is the hw mod to write to the mmc. If you have an A to A plugged in, on boot it'll stop in the bootloader and fastboot will work, unfortunately there is no commands you can actually run that will do anything. If you don't have an A to A plugged in, it will try to load the boot image. Since you didn't unlock, it won't boot the image, and it'll just die.
if all else fails, you can always go to amazon for replacement, remember amazon fire tv hasn't been a year old yet and you still have warranty for it, thats what i did with mine, i acted i didn't know what i was doing and suddenly it wouldn't load or boot up, etc.. u will need to know ur email adress or account thats associated with ur fire tv.. op korz .. they will do it... 100%
rbox said:
If you didn't follow the directions and didn't unlock, then it is bricked and the only way to fix it is the hw mod to write to the mmc. If you have an A to A plugged in, on boot it'll stop in the bootloader and fastboot will work, unfortunately there is no commands you can actually run that will do anything. If you don't have an A to A plugged in, it will try to load the boot image. Since you didn't unlock, it won't boot the image, and it'll just die.
Click to expand...
Click to collapse
Thanks for the reply rbox.
So what your saying is my Fire TV is dead.
I might just move on then to a new device like the Razor Forge TV when that comes out.
daffung said:
if all else fails, you can always go to amazon for replacement, remember amazon fire tv hasn't been a year old yet and you still have warranty for it, thats what i did with mine, i acted i didn't know what i was doing and suddenly it wouldn't load or boot up, etc.. u will need to know ur email adress or account thats associated with ur fire tv.. op korz .. they will do it... 100%
Click to expand...
Click to collapse
I'd love to return my FTV under warranty but i live in Australia and can't be bothered paying for postage to get it replaced
Just wondering if anyone has worked out a way of fixing this type of Brick?
Not sure was version of the software on, I'm hoping that it might be on 51.1.6.1 or 54.1.2.1
thanks
Phill360 said:
Just wondering if anyone has worked out a way of fixing this type of Brick?
Not sure was version of the software on, I'm hoping that it might be on 51.1.6.1 or 54.1.2.1
thanks
Click to expand...
Click to collapse
Depending on how much of the instructions you actually followed, and if your bootloader is 51.1.0.2 or older, there is a method that @AFTVnews.com is working on a writeup for that should recover it. But if the bootloader wasn't downgraded to 51.1.0.2, then it's dead.
Hi,
I put CM 11 on my fire phone. After I dialed a phone number and pushed send, the screen instantly went black. That was enoying so I tried to install the recent CM 11 from 02/16/2016. (Now I know that the display protection might have caused the issue) After the installation I booted the phone. After I had to choose the language in cyanogenmod in the phone was written that the installer was stopped. So I was in a loop of beeing asked for the language.
So I put OS (via adb sideolad) on the fire phone again and installed CM11 and the recent open gapps. Everytime the installer stopped and I was in that loop again.
I tried it with different Open gapps and CM11.
Now suddenly the Fire Phone does not do anything anymore. Just a black screen. I tried several button combinations with several time combinations. Even not the amazon sign appears.
I have two fire phones and am more or less scilled in flashing and installing. But now I do not know how to tread the issue.
I think about opening the Fire Phone and disconnect the battery for some seconds. That move might do something....
Any recommendations? Any ideas? Anybody had similar issues?
Thank you! Have a nice one!
Ingo
Some ideas...
Hi ingo,
welcome to the forums :cyclops:
first of all the following are just some ideas i've got of helping you in your case.
Maybe you already done some of them but anyway
Idea 1. Hold down Power button for about 10 secs or more (to try to reboot to see if the amazon logo appears)
Idea 2. Hold down Power button and Volume down together for about 10 secs or more (maybe we can get out of the boot loop).
Idea 3. Hold down Power button and Volume UP together for about 10 secs or more (maybe we can get out of the boot loop).
Idea 4. Don't charge the phone for about 3 Days and see if it shows something when you then connect the charger (then try to repeat Idea1 to Idea3).
After one of this succeed:
Your issue with CM not going over language selection is already known.
Try to remove SIM and use WLAN to go over the setup....
Or install the one from january (no issue) and then dirty update to the current one
If you killed your SafeStrap recovery you will have to go back to stock, root, safestrap and start over...
That's for now from me.
Report if something changed
regards
Will open the Fire Phone
Hi. Thank you for your answear! I appreciate that!
I checked your ideas already. The first ideas did not work out. I will open the Phone to disconnect the battery for a while. I will see what that may bring.
I will tell about the outcome of that.
Have a nice one.
Best Regards, Ingo
Dont forget: if you still (ok i doubt ) have warranty on the phone that the battery pack is secured inside with a "magic tape" that will break when you remove it...
Good luck
Will find sollution
Thank you for your reply. Warranty. Ahaha.:laugh: Would be funny to try it though.
I ordered the right tools for opebing the Fire Phone (There are two small torx screws).
I saw in the list of devices that there are 6 extra disks shown when I connect the phone to the pc. The PC just can see the content of one of them. I cannot open the files, the PC is not able to open the filetypes (for example adsp.b10)
I will keep on trying!
See you!
I got my new tools. Disconnecting the battery did not make it better. Same situation like before. So right now I do net know the next step.
Of course I tried to charge the phone, I tried different button combinations ......
Its a pitty. I have got two fire phones and it is the one with the 64gb.
I will keep on.. If anybody has a hint please tell me.
Thank you!
Regards Ingo
Anybody got an idea?
ingokabel said:
Anybody got an idea?
Click to expand...
Click to collapse
Hi,
after a while I start to try to fix my fire phone again. I still do not have any clew how to solve the issue.
Any of you?
hello to all, I have a tv tdsystems 50-inch 4k with android tv 7.1.1
I recovered from the manufacturer the firmware of the TV which is called install.img
I wanted to ask if there is someone willing to help me I have to edit the firmware himself with the official app google is root, thanks
Send me yours install. IMG.
My email [email protected] Ru.
I will do edit.
timersky said:
Send me yours install. IMG.
My email [email protected] Ru.
I will do edit.
Click to expand...
Click to collapse
hello sorry but I only read your answer now, I am very grateful for your help since you don't find anything on the internet about this soc, do you have the same TV or a similar one ?? I'm sending you all the content by email
Hello there, i have been searching for the install.img for my Star-X RealtekATV 43" but i cant seem to find it. Mine is stuck in Android LOGO and I cant any other ways to force reset it. please share the Install.img so i can try, thanks
ReagNkyaIV said:
Hello there, i have been searching for the install.img for my Star-X RealtekATV 43" but i cant seem to find it. Mine is stuck in Android LOGO and I cant any other ways to force reset it. please share the Install.img so i can try, thanks
Click to expand...
Click to collapse
hello, you have to ask your producer because almost all the .img files are different according to the manufacturer, I'm looking for a way to root my
I also have a problem like this (freezes in boot animation)
the device is gosonic gled-4350 model and it freezes when I simulate the secondary screen from the developer settings of this device
and I thought to solve the problem by opening the service menu with the service code, but I do not know the code of this device. What should I do?
ErrorVelet said:
I also have a problem like this (freezes in boot animation)
the device is gosonic gled-4350 model and it freezes when I simulate the secondary screen from the developer settings of this device
and I thought to solve the problem by opening the service menu with the service code, but I do not know the code of this device. What should I do?
Click to expand...
Click to collapse
I did the same mistake to my TV. However, I was able to recover from such freeze by forcing the TV to start in safemode. As I remember, I plugged off the TV from the power source. After that I plugged it in again and turned ON the TV from the remote while pressing at the same time on the [Vol-] button. Once I got into the system, I turned off the secondary display and rebooted again. This time everything was fine.
Hello xda,
as the title says: a friend brought me a sm-r800(don't know the branding; it's from Europe, Germany) to repair because it would shut down after the Samsung logo (logo appears around ~10s). Inside the download mode (wireless) everything is okay for hours.
I've flashed now around (today is my second and last try) 8 different ROMs (https://4pda.ru/forum/index.php?showtopic=978373&st=80#entry92121314 and other). 3part, 1part ROMs without success. Still the same behavior.
I'm done /shrug
Do you have an idea or some advice to me?
Thank you
/nepixl
If Combination Firmware not work...
Are you able to post Photo or Screen text from Odin Mode aka Download Mode?
Example...
Please help, bricked Gear S3 SM-R765S
Hello, I have a SM-765S (SM-R765SDAASKC). Unfortunately it is bricked, completely stuck in the ODIN mode. In the recovery non of the options are working (except for the power off). I managed to connect to the pc using a usb cable, but the...
forum.xda-developers.com
Best Regards
To be honest, I was never been there(normal downloadmode) before (tried directly the wireless mode) but the same result (Odin tells me always a green "pass!" after the flash process).
Happy to read your feedback!
Best Regards,
/nepixl
Photo looks good to me...
No Knox dripped...
Bootloader sboot.bin is SM-R800 from ASL2 Combination Firmware...
So next Question is...
ASL2 Combination firmware can boot or do the same?
Best Regards
Edit 1.
I mean exact this file:
COMBINATION-FT40_R800XXU1ASL2.tar.md5
You flashed this allready?
Appreciate your help, thanks for this.
adfree said:
Photo looks good to me...
No Knox dripped...
Bootloader sboot.bin is SM-R800 from ASL2 Combination Firmware...
So next Question is...
ASL2 Combination firmware can boot or do the same?
Best Regards
Edit 1.
I mean exact this file:
COMBINATION-FT40_R800XXU1ASL2.tar.md5
You flashed this allready?
Click to expand...
Click to collapse
Yes, the last flashed ROM was the COMBINATION-FT40_R800XXU1ASL2 from 4pda and its the same behavior.
Shows Samsung logo for ~10 seconds afterwards display goes black for hours. (my guess: its complelety shutting down/dies.) If I hit the "Power button" the same starts again. -If it helps, I could record a video about this.
I'm really running out of ideas and I'm happy for your feedback.
Any ideas what I could try?
Thank you and best regards
/nepixl
Okay, I guess I've missed an essential step while or after flashing.
Update firmware with NetOdin
Hi all, I noticed that the BSA4 update has been released everywhere except Australia. I've been able to get my hands on the firmware files but do not know how to get the watch to connect with NetOdin. Has anyone been able to do this? I've seen...
forum.xda-developers.com
" 7. After the files are downloaded, the Watch will reboot. Again, hold Home and highlight & select Recovery in the Reboot menu. "
This is something I've never done before.
I tried this now. Watch reboots 3x times after that ⇾ shutdown. -_-
Will it make a difference if I "reset" the watch right after the flashing process (after reboot?)?
/nepixl
A
Use Standard Settings in netOdin.
NOT change something...
B
Normally after flashing 1 file Combination Firmware... you have nothing to do... only wait for finish... booting...
After few Seconds Combination Firmware should start proper...
C
In theory... you could dump Logfiles from Watch... to see why it not proper...
Require USB cable...
D
It is possible to flash CSA or other files additional... but this increase risk to damge more...
E
Maybe with other Combination Firmware more luck...
No idea of Samsung changed something... maybe with newer Version more luck... or older...
Forgotten where ASL2 is in this chain of """Evolution"""...
Best Regards
Thank you very much for your effort on me. Really appreciate!
A:
Had always stock settings in (net)Odin - Check
B:
Okay, means to me: try more combination fw! - Sure, sometimes net Odin fails - repeat flash until Odin show a green file and SW reboots - Check
C:
Yea - will be my next step - To be honest, this is my first smartwatch flash (and first time flash via Wi-Fi ever). Flashed tons of smartphones but not a single Smartwatch yet. Usually I pull a logcat via USB. In theory that could work also on a SW? I mean: I'm connected by Wi-Fi in the same network - so adb could work? But I don't know if SW have the same android features like ADB or ability to pull logcat. -Aw, logcats requires rootaccess afaik ...
D:
Will stick to your suggest -> combination fw
E:
Okay - will search for more combination fw
Awesome community. Thanks, @adfree
Best regards, stay healthy.
/nepixl
SM = Smartwatch #lazy
ASL2 seems "latest" leak...
You allready checked this Version?
File-Upload.net - COMBINATION-FT40_R800XXU1ASG1.tar.md5.7z
Datei: COMBINATION-FT40_R800XXU1ASG1.tar.md5.7z. Die Datei wurde von einem User hochgeladen. Laden Sie auch kostenlos Dateien hoch mit File Upload.
www.file-upload.net
ASG1?
List of leaked FT40 files...
SM-R800 | Easy Firmware
easy-firmware.com
Best Regards
I guess not, will do it the next time and give feedback after
Thank you again.
/nepixl
Edit: Nice source! Been there too but the fact that I have to pay scares me (sure - the devs have alot of effort to grab that software). To be honest: Prefer to donate someone (you! ) from xda before I pay this page.
But this page is a good start to have a feeling what firmware could work for me.
Hi
I had same issue multiple times, I've tried to go to boot menu and did factory reset, after multiple reboot trials, it works but this is a workaround and very frustrating that I'm looking for a solution to fix permanently.
Hi,
Thanks for your reply!
okay, I tried the same now for some minutes with the suggested firmware (ASG from @adfree)
Seems I have no luck again :/
I tried as you said: factory reset (which is factory command here?) and reboot some times but nothing..
Do you think this could be more a hardware issue?
thankyou
Okay I guess there is more screwed than expected.
I've seen in a video that a screen with "resetting..." should appear after selecting recovery mode, which has never happened on this watch. 3 Reboots and the watch will showdown/displayoff
Any ideas?!
Hi guys
add me as onw how is suffering this problem, i had this problem long time ago , after so many tries to use the guarantee with no hope, now i had to fine a solution my self
tried deferent roms nothing changed
thank you for efforts beforehand
Hi everyone. Same problem here. the watch was bought in France, but i live in Brazil and it worked well for 2 years. The issue happened just after an update. i could install a combination file, but it's limited and i could not get access to anyother function but configs. if any of you have a tutorial step by step on how to fix it, i would really appreciate it! thanks
Hi all,
I created an account just to add my comment. I FOUND A LOOPHOLE I think...
My SM-R810 did the EXACT same thing!
I was in the middle of a work day and spun my wrist up to see the time. Black, hmmm... I held the power button and saw the Samsung logo, figured I might have accidentally not turned it on that morning. no biggie. Lunch time I check it out again, off. I turn it on and watch this time. 10 seconds and the "Samsung Galaxy Watch" screen turns back off. Hold the power button continuously and get into Recovery successfully, select Recovery to format the watch. It restarts like it's going to do it in the youtube videos I had just referenced, turns off after Samsung logo again. Now I'm pissed...
I know for sure I was at 87% battery when I walked into work this morning! Even the charging screen shuts off before it "loads up" the correct charge position, 87%. I brought my charger in and noticed that after 2 minutes of charging, the charger starts blinking red? So my next thought is maybe the battery is unstable or setting off some type of digital alarm.
THE SOLUTION THAT CLEARED MY PROBLEM:
Everything i did shuts off after 10 seconds EXCEPT for Download (Wireless) mode. So I left it in wireless mode for an hour and it successfully drained to 24%. I placed it on the charger and brought it up to 46% then turned it on. It immediately started formatting the watch as i requested 5 different times lol
FIXED!!!!!
I'm an EET but have spent little time tinkering with this watch. I know the battery is fully removable but does anyone out there know if this all could have been caused by a voltage instability that auto-triggered a safe shutdown - something like that? I'd like to make sense of the situation so that I may prevent it. I.E., overcharging the battery, watching its temperature, etc.
Thanks all!
-General