Related
Hi guys,
Since today Huawei delivers the open sourcecode for the drivers, I guess.
Anyone in here capable to create a nice clean AOSP ROM or anything else good for our tablet?
Search link for LTE version:
http://m.huawei.com/enmobile/consum...roid=M2-A01L&proKey=Tablets_T/Tablets/M2-A01L
Direct download for LTE version:
http://download-c.huawei.com/downlo...oadId=89345&version=347349&siteCode=worldwide
Search link for WiFi version:
http://m.huawei.com/enmobile/consum...roid=M2-A01w&proKey=Tablets_T/Tablets/M2-A01w
Direct download for WiFi version:
http://download-c.huawei.com/downlo...oadId=89346&version=347353&siteCode=worldwide
I do not have the experience with ROM building, forking, ... etc. here.
One good room would be good.
Edit. Nevermind
Anyone with the LTE version of this can you upload to a cloud link so that I can download? I would rather not waste my time having to send an email to [email protected] just to get it. Thanks
Huawei Open Source Released
Hey,
maybe it is late, i have found the open source.
the link: consumer.huawei.com/en/opensource/
and we can find m2-a01l in the tablet part, and it is on page 4.
Emm...i dont know how many people use this tablet because it is out of date.:laugh:
and i dont know if it is everything we want
whatareyou007 said:
Huawei Open Source Released
Hey,
maybe it is late, i have found the open source.
the link: consumer.huawei.com/en/opensource/
and we can find m2-a01l in the tablet part, and it is on page 4.
Emm...i dont know how many people use this tablet because it is out of date.:laugh:
and i dont know if it is everything we want
Click to expand...
Click to collapse
Hi! Thank you, i'll do an AOSP for our poor tablet, the only problem in my case, I'm unable to unlock the bootloader because i haven't in dev options "OEM unlock". If I'll pass this issue, I'll immediately start to develop the ROM.
Crypto18 said:
Hi! Thank you, i'll do an AOSP for our poor tablet, the only problem in my case, I'm unable to unlock the bootloader because i haven't in dev options "OEM unlock". If I'll pass this issue, I'll immediately start to develop the ROM.
Click to expand...
Click to collapse
Hi! Have you able to develop for our poor table? 1 stable ROM should be enough
and0ng said:
Hi! Have you able to develop for our poor table? 1 stable ROM should be enough
Click to expand...
Click to collapse
The only problem in this moment still remain unlocking bootloader. I'm searching solutions
Crypto18 said:
The only problem in this moment still remain unlocking bootloader. I'm searching solutions
Click to expand...
Click to collapse
Yeah it's a pain to unlock the bootloader. But since I need to install Google Workspace device policy I have no other option
@Crypto18 - There is a possibilty to unlock the bootloader by using dc-unlocker - amount about 4 Euro. I had success in doing so a year ago. It would be very nice to get an AOSP-ROM für the tablet.
I think, I unlocked it with dc-unlocker, too, four years ago or so.
I would be happy to have any clean/empty/fresh AOSP ROM for this tablet, as up to today it is still fast and really usable.
If you need any help, I would also be eager to learn how to do it (building a ROM). @Crypto18
Crypto18 said:
Hi! Thank you, i'll do an AOSP for our poor tablet, the only problem in my case, I'm unable to unlock the bootloader because i haven't in dev options "OEM unlock". If I'll pass this issue, I'll immediately start to develop the ROM.
Click to expand...
Click to collapse
I did the DC-unlocker thing today as described in the sticky, so it still works. Somebody in this thread mentioned that it worked for him without the OEM unlock option (it disappeared in EMUI 4), but to be on the safe side I had done a downgrade to EMUI 3 before (the oldest one I found didn't have a working dialer, I didn't try the landscape calculator trick to activate the manufacturere mode, but updated to a later EMUI 3 version that had a a working dialer: "Huawei MediaPad M2-801L Android 5.1.1 EMUI 3.1 B007.zip").
I am now looking for a working TWRP (see my post in the sticky thread a few minutes ago).
If you manage to unlock your bootloader, I would be willing to go the "build your own version from scratch" way with you. I have experience as embedded Linux developer one decade ago, but never did it for Android. Would be more fun to have a second person interested in this "classic" tablet.
@coocooc , @Crypto18 ,
Have you made any progress with developing a custom rom?
@coocooc - Please search for "TWRP-3.1.0-recovery-MediaPadM2-10.0-LISZT-A01L-A01W.img" in TWRP. That's the TWRP you're looking for.
rotter99 said:
@coocooc , @Crypto18 ,
Have you made any progress with developing a custom rom?
Click to expand...
Click to collapse
Crypto18 so far did not come back, and I didn't start the journey yet.
I am on the way to prepare a Linux laptop for building Android and SBC stuff, but family life does not allow to spend many hours on my pet projects.
I wrote a mail to Huawei to get the latest sources (EMUI 4), but the first level support shown on their GPL site couldn't fulfill the wish. They gave me a developer address to apply to; let's see how this ends.
gelrav said:
@coocooc - Please search for "TWRP-3.1.0-recovery-MediaPadM2-10.0-LISZT-A01L-A01W.img" in TWRP. That's the TWRP you're looking for.
Click to expand...
Click to collapse
Thanks for the hint! I will try this TWRP version tonight. Which EMUI version are you using with this TWRP (EMUI 3 or 4)? Is there something to check in the flash layout first, to succeed with this TWRP?
@coocooc - I'm using a Huawei Mediapad M2 10.W with Emui 3.1., Android 5.1.1.
If you're on Mediapad 801L, the above mentioned TWRP will not work for you!
I am using “TWRP-3.1.0-recovery-MediaPadM2-10.0-LISZT-A01L-A01W.img“ om my M2-A01W and it working without any problems.
gelrav said:
@coocooc - I'm using a Huawei Mediapad M2 10.W with Emui 3.1., Android 5.1.1.
If you're on Mediapad 801L, the above mentioned TWRP will not work for you!
Click to expand...
Click to collapse
@gelrav Oh that might be the reason for my problems as I do use the 801L version. What alternative TWRP ist available then?
coocooc said:
@gelrav Oh that might be the reason for my problems as I do use the 801L version. What alternative TWRP ist available then?
Click to expand...
Click to collapse
Funny, the name of the TWRP file suggests that it is valid for both the L and the W versions of the M2-A01.
What is exactly the problem with this file?
I unlocked both the phone und FRP on my device before installing this file.
I am on EMUI 3.1. and Android 5.1.1.
@coocooc
Maybe this link can help you getting further:
Downloads for : Huawei -All-General-Generic- | AndroidFileHost.com | Download GApps, Roms, Kernels, Themes, Firmware and more. Free file hosting for all Android developers.
Download GApps, Roms, Kernels, Themes, Firmware, and more. Free file hosting for all Android developers.
androidfilehost.com
I am not asking for Huawei M3 specific rom!
I am not asking for anything, I am just total noob who read about Lineage and wants to install it but knows nothing about it. I made thread asking same question on Reddit and it was deleted by moderator without single reply, they have rule there where its prohibited to ask this most essential basic and fundamental question.
I checked the "compatible device" list and M3 isnt there, neither are M5 or M6. I dont even understand why is there compatibility list and what would happen should I attempt to install it on M3. I dont even know if I can even attempt it.
I just want someone to tell me if I should forget about it or if this is potentialy possible but with some extra difficulties and risks becose its not supported device.
It's a different thing to put lineageOS on a phone or tablet than putting Linux on a PC. A Linux distro usually conatains all necessary drivers to run on most PCs. A LineageOS ROM contains much more device specific proprietary code. So there exists a different ROM for each device or group of related devices. For M3 have a look there:
https://forum.xda-developers.com/mediapad-m3/development/rom-t3945684
It's not official. That's why you didn't find it in compatible device list.
Thank you for reply kurtn. So you are saying that I can run normal Lineage that isnt special rom made for some specific device just fine but some things will not work becose of drivers?
I only use my tablet for listening music and browsing web, as long as bluetooth and wifi works I dont care about the various sensors and cameras. Is there higher risk of bricking the device if not using device specific rom?
Lanthanides said:
I am not asking for Huawei M3 specific rom!
I am not asking for anything, I am just total noob who read about Lineage and wants to install it but knows nothing about it. I made thread asking same question on Reddit and it was deleted by moderator without single reply, they have rule there where its prohibited to ask this most essential basic and fundamental question.
I checked the "compatible device" list and M3 isnt there, neither are M5 or M6. I dont even understand why is there compatibility list and what would happen should I attempt to install it on M3. I dont even know if I can even attempt it.
I just want someone to tell me if I should forget about it or if this is potentialy possible but with some extra difficulties and risks becose its not supported device.
Click to expand...
Click to collapse
WiFi and Bluetooth are highly device specific. I've linked a ROM for you.
I have M3, that M3 Lite you linked is different device. Or did you mean it should work on M3 just fine?
By the way, if there is another device with similiar chipset, does that mean I can use rom for that device? M3 has Kirin 950 so my thinking is that maybe I can use rom that was made for some Kirin phone, or is that bad idea?
Here is link from xda- lineage news article that claims 15.1 version ROM is avaliable for Huawei Mate 8. That phone uses exact same chipset. https://www.xda-developers.com/openkirin-lineageos-honor-8-honor-note-8-huawei-p9-huawei-p9-plus-huawei-mate-8/amp/
Lanthanides said:
I have M3, that M3 Lite you linked is different device. Or did you mean it should work on M3 just fine?
By the way, if there is another device with similiar chipset, does that mean I can use rom for that device? M3 has Kirin 950 so my thinking is that maybe I can use rom that was made for some Kirin phone, or is that bad idea?
Here is link from xda- lineage news article that claims 15.1 version ROM is avaliable for Huawei Mate 8. That phone uses exact same chipset. https://www.xda-developers.com/open...8-huawei-p9-huawei-p9-plus-huawei-mate-8/amp/
Click to expand...
Click to collapse
Same chipset is a good starting point.
I recently purchased an tab S4 just an update from my previous Samsung tablet. I was wondering is there more ROMs for this tablet or ROMs currently in development? I noticed theres like 2 ROMs for this tablet. I have a note 8 and I'm currently running deluxerom on and it, and I really enjoy the tweaks and customization I'm able to do. I was looking for a same kind of feature for my tablet. Would greatly appreciate the answers I'm looking for. Thanks!
Mkami said:
I recently purchased an tab S4 just an update from my previous Samsung tablet. I was wondering is there more ROMs for this tablet or ROMs currently in development? I noticed theres like 2 ROMs for this tablet. I have a note 8 and I'm currently running deluxerom on and it, and I really enjoy the tweaks and customization I'm able to do. I was looking for a same kind of feature for my tablet. Would greatly appreciate the answers I'm looking for. Thanks!
Click to expand...
Click to collapse
Pretty much zero support. You can get a few 9.0 GSI ROMs to boot, but they all have issues. Mine has been sitting around since it was purchased while still using my old 2014 model.
veekay said:
Pretty much zero support. You can get a few 9.0 GSI ROMs to boot, but they all have issues. Mine has been sitting around since it was purchased while still using my old 2014 model.
Click to expand...
Click to collapse
Aww no way!? Really? I excitingly got this tablet cause of the features and thought perhaps there would be amazing ROMs for this particular tablet, but I guess not xD What are GSI ROMs? Also as a desperate attempt would other tablet ROMs work on this s4? Thanks mate!
Mkami said:
Aww no way!? Really? I excitingly got this tablet cause of the features and thought perhaps there would be amazing ROMs for this particular tablet, but I guess not xD What are GSI ROMs? Also as a desperate attempt would other tablet ROMs work on this s4? Thanks mate!
Click to expand...
Click to collapse
I had thought the same thing, but it seems the S3 is the last tablet to get real support.
https://forum.xda-developers.com/project-treble/trebleenabled-device-development
Some of the ones for 9 will work, but most features won't work too well, if at all.
You might be able to get another rom to work, I know I had no luck. Even trying ones with similar hardware, they all failed to even flash since the booting numbers are different.
Kind of have to be satisfied with Samsung, half baked custom roms or sell the thing.
Mkami said:
Aww no way!? Really? I excitingly got this tablet cause of the features and thought perhaps there would be amazing ROMs for this particular tablet, but I guess not xD What are GSI ROMs? Also as a desperate attempt would other tablet ROMs work on this s4? Thanks mate!
Click to expand...
Click to collapse
First,download "Treble Check" app from playstore & read for your device...
https://www.xda-developers.com/flash-generic-system-image-project-treble-device/
(Some GSIs roms are not compatible with some devices!)
veekay said:
I had thought the same thing, but it seems the S3 is the last tablet to get real support.
https://forum.xda-developers.com/project-treble/trebleenabled-device-development
Some of the ones for 9 will work, but most features won't work too well, if at all.
You might be able to get another rom to work, I know I had no luck. Even trying ones with similar hardware, they all failed to even flash since the booting numbers are different.
Kind of have to be satisfied with Samsung, half baked custom roms or sell the thing.
Click to expand...
Click to collapse
Hey Veekay I tried it and you're right unfortunately I came across the same issue as you brother
Now I'm stuck and I need help sorting my device out, was wondering if you knew this issue or could help?
When I got the stock firmware back and then when I flash TWRP with odin after going into TWRP I get 0mb as internal
so when I format and then go back into my load up the screen after SAMSUNG says "verification failed" and then reset
on the bottom. I tried other options as well. Without even wiping on TWRP the devices boots up into the setup wizard for the firmware fine
but after I wipe TWRP so I can get access to my internal drive my samsung boots into that verification reset screen. Got any clue as to how I can
resolve this issue? Thanks a bunch!
daitalos said:
First,download "Treble Check" app from playstore & read for your device...
https://www.xda-developers.com/flash-generic-system-image-project-treble-device/
(Some GSIs roms are not compatible with some devices!)
Click to expand...
Click to collapse
Hey! Thanks for your reply, will this work for PIE? I can't downgrade from PIE to OREO
and I don't know if GSI even works properly on my device
Mkami said:
Hey Veekay I tried it and you're right unfortunately I came across the same issue as you brother
Now I'm stuck and I need help sorting my device out, was wondering if you knew this issue or could help?
When I got the stock firmware back and then when I flash TWRP with odin after going into TWRP I get 0mb as internal
so when I format and then go back into my load up the screen after SAMSUNG says "verification failed" and then reset
on the bottom. I tried other options as well. Without even wiping on TWRP the devices boots up into the setup wizard for the firmware fine
but after I wipe TWRP so I can get access to my internal drive my samsung boots into that verification reset screen. Got any clue as to how I can
resolve this issue? Thanks a bunch!
Click to expand...
Click to collapse
Have you tried just reloading the latest stock firmware from scratch?
Yup, its unfortunate that there isn't much community support for this device. The Tab S4 is Project Treble supported and a few GSI ROMS do work. But as others have said they are unstable and not for use as a daily driver. We have a few discussion threads here talking about them.
veekay said:
Have you tried just reloading the latest stock firmware from scratch?
Click to expand...
Click to collapse
Would that work? If I did that I would still be able to download and install TWRP and have a root? Because of it being PIE
UndeadAnarchy said:
Yup, its unfortunate that there isn't much community support for this device. The Tab S4 is Project Treble supported and a few GSI ROMS do work. But as others have said they are unstable and not for use as a daily driver. We have a few discussion threads here talking about them.
Click to expand...
Click to collapse
I am going to do more research on these projects because I really wish there was more ROMs its quite an amazing tablet but the potential with the stock ROM lacks a lot
Mkami said:
Hey! Thanks for your reply, will this work for PIE? I can't downgrade from PIE to OREO
and I don't know if GSI even works properly on my device
Click to expand...
Click to collapse
Generic System Image (GSI) list :
https://github.com/phhusson/treble_experimentations/wiki/Generic-System-Image-(GSI)-list
you can try only "Android 9 Pie" official or unofficial gsi roms..
and remember ! Some GSIs roms maybe are not compatible with some devices! you can ask for your device on each thread
(for example look here): https://github.com/phhusson/treble_experimentations/issues/777
(usually this Gsi aosp 9 phh, generally works on most devices...BUT! ask first,and discuss it in the thread)
https://forum.xda-developers.com/pr...vice-development/aosp-9-0-phh-treble-t3831915
daitalos said:
Generic System Image (GSI) list :
https://github.com/phhusson/treble_experimentations/wiki/Generic-System-Image-(GSI)-list
you can try only "Android 9 Pie" official or unofficial gsi roms..
and remember ! Some GSIs roms maybe are not compatible with some devices! you can ask for your device on each thread
(for example look here): https://github.com/phhusson/treble_experimentations/issues/777
(usually this Gsi aosp 9 phh, generally works on most devices...BUT! ask first,and discuss it in the thread)
https://forum.xda-developers.com/pr...vice-development/aosp-9-0-phh-treble-t3831915
Click to expand...
Click to collapse
Can I do this without stock ROM and only TWRP? Because having the stock ROM is disabling my twrp to function without wiping and if I wipe than my stock ROM doesn't work
Thanks!
Mkami said:
Can I do this without stock ROM and only TWRP? Because having the stock ROM is disabling my twrp to function without wiping and if I wipe than my stock ROM doesn't work
Thanks!
Click to expand...
Click to collapse
Sorry,but I don't understand what do you mean " without stock rom and only twrp"...
you can install a Gsi rom, with two ways
Via TWRP, or Via Fastboot : https://www.xda-developers.com/flash-generic-system-image-project-treble-device/ (Tab S4 is a-only arm64)
for any other question, it is better to ask in the thread : https://forum.xda-developers.com/pr...vice-development/aosp-9-0-phh-treble-t3831915
(read carefully in OP & you can post,every single question there for your device,and you will get certainly help from the developer or from any other user..)
Mkami said:
Can I do this without stock ROM and only TWRP? Because having the stock ROM is disabling my twrp to function without wiping and if I wipe than my stock ROM doesn't work
Thanks!
Click to expand...
Click to collapse
You are going to have to just wipe it and start over from square one, unless you made a TWRP backup before starting all of this.
Download and flash the latest stock rom from recovery and then you can load twrp again.
I was looking at the possibility of using GSI's on some devices, and while they can offer new life to older devices, they're not entirely stable all the time unless you're willing to make your own changes. I know Lineage has made some excellent progress, but it's not fullproof yet and I wouldn't try it unless you're willing to not use your device as a daily use device.
I had an extra T-Mobile Revvlry which is basically a rebranded Moto g7 Play that I installed the Lineage GSI image and it works fairly well. However, this is more the exception to the rule and Moto devices, I feel, are far simpler in design vs certain Samsung devices. It also had a ton of trial and error involved for me to get it up and running properly.
Is it possible as the s4 becomes older, more people buy it and Samsung stops releasing official updates that someone will come along and create a ROM for it? Or is it more like Samsung locked the bootloaders and its close to impossible to write a ROM for it? Is it still possible to root the s4?
slipnslider said:
Is it possible as the s4 becomes older, more people buy it and Samsung stops releasing official updates that someone will come along and create a ROM for it? Or is it more like Samsung locked the bootloaders and its close to impossible to write a ROM for it? Is it still possible to root the s4?
Click to expand...
Click to collapse
Read very carefully without rush ! for " WETA Kernel + Encryption disabler " etc
especially, read the user comments carefully, and ask on the thread for any questions you have..
https://forum.xda-developers.com/galaxy-tab-s4/development/recovery-twrp-3-3-0-sm-t83x-t3928278 (Pie version)
https://forum.xda-developers.com/showpost.php?p=79483624&postcount=2
https://forum.xda-developers.com/galaxy-tab-s4/how-to/guide-sm-t83x-twrp-magisk-t4059227
( Newest Odin v3.14.4 is there : https://dl2018.sammobile.com/Odin3-v3.14.4.zip )
Thanks. I took a quick peak at the roms and kernels in the roms and kernels forum and they are pretty much all abandoned.
Someone did mention that the LOS 16.0 and ArrowOS GSI's work alright but are a bit buggy.
slipnslider said:
Thanks. I took a quick peak at the roms and kernels in the roms and kernels forum and they are pretty much all abandoned.
Someone did mention that the LOS 16.0 and ArrowOS GSI's work alright but are a bit buggy.
Click to expand...
Click to collapse
samsung,maybe at the end of july to give the upgrade to android 10....it is very likely to happen I think
yes,all Gsi Roms still have various problems unfortunately...
my opinion is: stay to stock rom for now....you can "uninstall" many applications if you want & without root, via "samsung package disabler"(paid) from playstore, or with this way:
https://beebom.com/how-remove-bloatware-android-without-root/
also,you can Install "NiceLock Downloader Companion App" ,to add some features on your device : https://forum.xda-developers.com/galaxy-note-9/themes/nicelock-module-download-links-module-t3923844
with this way I operate my device until now..
Does anyone have LineageOS for Samsung Galaxy Tab A6?
this tablet no new custom rom for this device to upgrade Android 10 or 11 , while Samsung Galaxy j5 has Lineage os 17 and 18
Please build custom rom for this device, anyone can do
Sorry that nobody replied.
You need to make your own custom ROM from scratch.
Besides, it's probably going to be a bit slow.
Hello, Thank you to answer my post about SM T280
I wanted to build this But I don't have complete guide to build ROM and I don't know how to start I have seen some videos and sites about building ROM but didn't helped and faced me some errors specially in REPO SYNC STEP
I'm a new member. You have a better chance of getting a good reply if you ask in this thread:
[ROM][LineageOS-14.1] Samsung Galaxy Tab A 7.0 - SM-T280 (gtexswifi)
Hello all! I've got the ROM working. Only problem is that once I add a google account and restart, I start to get the "Custom Binary blocked by FRP lock" message. Any way to disable FRP before the first reboot? Or force FRP to allow the custom...
forum.xda-developers.com
T2100-0 said:
I'm a new member. You have a better chance of getting a good reply if you ask in this thread:
[ROM][LineageOS-14.1] Samsung Galaxy Tab A 7.0 - SM-T280 (gtexswifi)
Hello all! I've got the ROM working. Only problem is that once I add a google account and restart, I start to get the "Custom Binary blocked by FRP lock" message. Any way to disable FRP before the first reboot? Or force FRP to allow the custom...
forum.xda-developers.com
Click to expand...
Click to collapse
Thanks I have seen this
Maybe I find a way to build Lineage OS 17.1 for this tablet
So Be patient...!
COMING SOON.....!
I'm using this rom
striker59 said:
I'm using this rom
Click to expand...
Click to collapse
Thanks but this is not enough Google no longer supports Android 5.1.1 We need to create new Android for this device to create this we must know how to create device and kernal tree for this device unfortunately there is no clear instructions to build for such devices and I have no knowledge
I asked for some developers but they said that the chipset of this tablet is speedtrum not Qualcomn and building device tree for these chispset is hard and so on
striker59 said:
I'm using this rom
Click to expand...
Click to collapse
The latest build is lineage 14 but this Rom has some bugs the best point for this Rom is that you can use your SD Card stoarge as your internal stoarge so you can install a lot of apps with large sizes it depends for your SDCard stoarge But the big problem is about Googleplay services some apps couldn't run without Google Play like Duolingo
As a result If you want install apps that need google play you should install official Rom with lack of stoarge if you want install alot of apps you should use lineage14 but no google play support and you have some bugs
I created new device tree for this tablet but has errors during the build I put my device tree link so please someone help to edit or upgrade it that is all I know maybe I continue it later
GitHub - Ali-Git-Official/android_device_samsung_gtexswifi
Contribute to Ali-Git-Official/android_device_samsung_gtexswifi development by creating an account on GitHub.
github.com
Zhao li said:
I created new device tree for this tablet but has errors during the build I put my device tree link so please someone help to edit or upgrade it that is all I know maybe I continue it later
GitHub - Ali-Git-Official/android_device_samsung_gtexswifi
Contribute to Ali-Git-Official/android_device_samsung_gtexswifi development by creating an account on GitHub.
github.com
Click to expand...
Click to collapse
Use _mone's tree or something.
I'm trying to port the A 10.1 (2016)'s ROM to the T280, building a ROM from scratch is hard for me.
T2100-0 said:
Use _mone's tree or something.
I'm trying to port the A 10.1 (2016)'s ROM to the T280, building a ROM from scratch is hard for me.
Click to expand...
Click to collapse
Good luck Thanks
Please add option to select SD card as internal Stoarge .It is Mandatory option for this tablet
T2100-0 said:
Use _mone's tree or something.
I'm trying to port the A 10.1 (2016)'s ROM to the T280, building a ROM from scratch is hard for me
Click to expand...
Click to collapse
Yes also for me is hard because we have no complete guide for creating dt .
I am trying to build Android N lineage or other projects first then build for higher versions. we have also some bugs for cm14 however I have solved mone's rom issue about Restarting Randomly it was very effective .The tablet will not restart anymore
Lineage OS 14 T280 bug: Prevent from Restarting Randomly
Hello I find a way to show you about the bug I'm using CM14 for Samsung Galaxy Tab A6 (T280)that was created by mone the last version of android for this tab I don't know you have faced this error before but when I'm using this Rom and work...
forum.xda-developers.com
Zhao li said:
The tablet will not restart anymore
Lineage OS 14 T280 bug: Prevent from Restarting Randomly
Hello I find a way to show you about the bug I'm using CM14 for Samsung Galaxy Tab A6 (T280)that was created by mone the last version of android for this tab I don't know you have faced this error before but when I'm using this Rom and work...
forum.xda-developers.com
Click to expand...
Click to collapse
Mine only restarts if it's doing a hard task. In _mone's first build, the red lines stopped it restarting.
Zhao Li:
Click to expand...
Click to collapse
Good luck Thanks
Please add option to select SD card as internal Stoarge .It is Mandatory option for this tablet
Click to expand...
Click to collapse
I'm not the best at porting. It's just easier to do.
If you want, you could make a version with an option like that.
T2100-0 said:
Mine only restarts if it's doing a hard task. In _mone's first build, the red lines stopped it restarting.
Click to expand...
Click to collapse
Yes you're right My tablet restarted again and the method did not work either
So I returned to lollipop.
T2100-0 said:
the red lines stopped it restarting
Click to expand...
Click to collapse
What is the red line that you mentioned?
T2100-0 said:
If you want, you could make a version with an option like that
Click to expand...
Click to collapse
How?
Zhao li said:
What is the red line that you mentioned?
Click to expand...
Click to collapse
In _mone'sold LOS 14 builds, sometimes red lines flashed around the edges around the screen.
Zhao li said:
How?
Click to expand...
Click to collapse
I'm going back to building. I'm just going to build LOS 16 for the T280. I don't want to put too much strain on this tablet.
T2100-0 said:
I'm going back to building. I'm just going to build LOS 16 for the T280. I don't want to put too much strain on this tablet.
Click to expand...
Click to collapse
Any progress my dude?
Zhao li said:
Thanks I have seen this
Maybe I find a way to build Lineage OS 17.1 for this tablet
So Be patient...!
COMING SOON.
Click to expand...
Click to collapse
Some months later ..and ?
My device which I want to port is sm-a325n (galaxy a32).
I know there is existing thread that include the twrp image for a32 but It doesn't work for me.
So I want to know how to build it myself but I need help.
Thank you.
N523A said:
My device which I want to port is sm-a325n (galaxy a32).
I know there is existing thread that include the twrp image for a32 but It doesn't work for me.
So I want to know how to build it myself but I need help.
Thank you.
Click to expand...
Click to collapse
bit of a late reply but did you try sky hawk recovery project that was built recently for this phone? works for me on android 11 and 12 firmware just fine