I'm a total n00b at android and need your help.
I have a Note 4 on ATT. Using ODIN a while back, I tried to load Marshmallow on the phone using an .md5 file (2 gb). The process completed, but the phone is stuck at the ATT Logo. Does not boot.
I understand ATT has a bootlock on the device. I want to restore everything to stock the way it was so I can use my phone. I tried DL'ing a few roms that were labeled as "stock" but I get an error on ODIN:
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't even know what ROM I should be downloading or where to get it from. Samsung Mobile doesn't have the n910A. What should I do?
Related
So my Sprint S3 asked me if I wanted to update it this morning, and I said yes and it downloaded the update and everything then rebooted. Clockwork recovery asked if it could override the stock recovery and re-root it and I selected yes to both. It restarted again and would not go past the Samsung logo after the Sprint animation. I tried to load a recovery image I had through Clockwork but it failed. At this point it would not turn on so I took it into a Sprint store. Of course they denied to work on it because it was rooted but now my phone is stuck in download mode. I cannot go into recovery mode or even just power it on normally. It is in "Odin mode" and also has the "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." I tried to flash a stock rom in Kies but it fails to connect, so I tried Odin 3.09 as well as 3.04 and both fail with
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
PLEASE HELP :crying::crying:
I flashed the wrong recovery in flashify. But I think it's in a soft brick state. When I reflash to a previous recovery, this is what I get:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried to flash twrp 3.0 zerofltespr and I think it was the wrong file for the wrong device. But the error in Odin Mode I get is "unsupport dev_type". When I plug the phone into the computer, it will autoplay the internal storage and SD card.
any ideas?
Sakui
Hello everybody !
I bought a Note 4 N910A unlocked on amazon but I have now a problem after an failed attempt to go 6.0.1.
My version was the DOI2 (5.1.1.) but I couldn't succed via flashing in recovery mode (update via sd impossible) neither with Odin (stuck at the beginning of the system bar).
I tried several official rom via Odin (N910AUCU2DOI2, N910AUCU1COC4, N910AUCU2COC6...) but same thing : stuck at the beginning of the system bar.
I tried also with a pit file and a nand erase all, but it's not working.
I have no access to recovery, only download mode.
Here is the rapport :
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't know what to do know...
Thanks for you help !
PS : the phone is under warranty but maybe I can find a way before going to the store (in 2 weeks). And I would prefer not use a root way too, unless I have to ^^
Once you were stock to begin with, you should NEVER have to use a PIT file (unless you found some way to change the partition sizes).
Looking at that log, I suspect the issue is with your data cable or PC. I'd recommend trying this on another PC and data cable (just to be sure). It is unlikely that your device is one of those with a defective NAND chip for storage.
Thanks for answer and it worked with an another cable :good:
I'm now in COC6 (5.0.1) and I'm wondering if I can make an update with Odin to go directly in 6.0.1 or I need to make all the others updates?
I have to do all the wipes first?
Thanks for your advices!
I have a Chinese Galaxy Tab pro 8.4 sm-t321, trying to flash TWRP recovery on it using Odin. I have rooted the device using CFAutoroot through Odin.
I downloaded twrp-3.1.1-0-mondrianlte.img.tar and used Odin v3.12.
Odin manages to install correctly (i think?) and it shows "Pass!"
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
But trying to boot into recovery mode fails and it boots into odin mode:
Could not do normal boot.
ODIN MODE
...
UDC START
Could someone tell me what i did wrong? How do it get TWRP to install correctly?
I just want to install google play on it and the guide I read needed TWRP to install Open GApps.
Many thanks
hello
googleplay on googleplay site
regards
Can someone help me on this? My phone was upgrading from 5.1.1 to 6.0.1 and then it died, so I turned it back on to download mode, and used a stock image of 5.1.1, and no luck. I tried 6.0.1, and still no luck.
Odin logs: (same thing with both)
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help, this is my personal phone I use daily. If you can help me with 4.4.4, that would be good too. :good:
I also unticked the bootloader option.