Related
I only found similar information for another device here. So I decided to share my experience with you.
I got myself an MTCD device which is obviously manufactured by Klyde (MCU code: KLD).
Today I tried to work on the software and found the device to display good reception in terms of WiFi indicator bars and 72Mbps downstream speed. The access point was quite close too. However despite the claimed reception opening web-pages was almost impossible and often ended in timeouts.
For me it was clear the bad "antenna" (which is basically just a cable visible at the back of the device) is the cause for this.
So I decided to change this.
After opening the device I could see that there is an internal "antenna" and a second antenna which is the one visible at the back.
I know the device only has 2.4GHz WiFi so I just cracked up an old USR WLAN router I was not using any more. This router got 2 replaceable antennas and luckily the antenna ports were not soldered to the board but connected using cables.
Therefore I could simply screw the jacks from the WLAN router to the DTV holes (unused on my device) on the back and solder the cables to the board.
Here are some pictures:
After this "surgery" the radio still fits properly to my car. You might have to be careful using antennas which do not stand off too wide at the back of the unit.
The result was a dramatically increased wireless quality. In fact it does not show more signal strength bars than before and also still sticks to 72Mbps but web pages now open immediately, downloads from play store are quick as expected.
Given the fact those antennas are cheap (less than $1 on ebay) I can't really understand why this is not offered stock.
Cool, KLD MTCD units use an RTL8723bu (you can see it near where the 2 antennas are soldered) its a combined BT/WiFi chip so you may get better BT reception too.
typos1 said:
KLD MTCD units use an RTL8723bu ... its a combined BT/WiFi chip so you may get better BT reception too.
Click to expand...
Click to collapse
Thanks for the reply. I didn't even check this but looks like you're totally right. I didn't have bluetooth connectivity issues before though. However I didn't use it much yet.
Thank you.
@SkyBeam2048
may I get the information which CPU your unit is working with?
I got a 7.1" unit manufactured by Klyde with an 8-core Cortex-A53 at 1.4GHz.
Unfortunately this unit works with Android 5.1.1 instead of 6.x and I am looking for an update.
Does your unit have something like a deep sleep mode, so that there is no cold boot after a short break?
By the way... I am talking about this unit...
rigattoni said:
@SkyBeam2048
may I get the information which CPU your unit is working with?
I got a 7.1" unit manufactured by Klyde with an 8-core Cortex-A53 at 1.4GHz.
Unfortunately this unit works with Android 5.1.1 instead of 6.x and I am looking for an update.
Does your unit have something like a deep sleep mode, so that there is no cold boot after a short break?
By the way... I am talking about this unit...
Click to expand...
Click to collapse
Please post a pic of your settings/about device screen so we know what unit you have ?
rigattoni said:
may I get the information which CPU your unit is working with?
I got a 7.1" unit manufactured by Klyde with an 8-core Cortex-A53 at 1.4GHz.
Click to expand...
Click to collapse
My one is a PX5 device (8 core 64-bit [email protected] and 2GB memory.
However without having more information on your device nobody will be able to tell you if you got a PX5 or some custom design.
As asked here you might post the system about screen to get more information on the device you have.
The thread here was mainly opened to discuss about changing antenna on my device. Perhaps it would by worth for you to open your own thread for your issue and how to upgrade (if possible).
SkyBeam2048 said:
My one is a PX5 device (8 core 64-bit [email protected] and 2GB memory.
However without having more information on your device nobody will be able to tell you if you got a PX5 or some custom design.
As asked here you might post the system about screen to get more information on the device you have.
The thread here was mainly opened to discuss about changing antenna on my device. Perhaps it would by worth for you to open your own thread for your issue and how to upgrade (if possible).
Click to expand...
Click to collapse
Indeed, the "1.4Ghz" bit is strange - it should be 1.6 (RK3188/PX3), 1.5 (RK3368/PX5) or "1.2" (Intel Sofia), not 1.4Ghz.
If its not a typo then it could be an Ownice octacore unit one of which I saw recently with an MCU prefixed by "KLD" suggesting that theyre made by KLD (which was news to me as I thought Ownice was a manufacturer in their own right), unless it was coincidently a random string of letters.
When he posts a screenshot we ll know . . .
Yeah, sorry for capturing your Wifi thread...
This is the unit which has been sent.
But to show you what I have:
rigattoni said:
Yeah, sorry for capturing your Wifi thread...
This is the unit which has been sent.
But to show you what I have:
Click to expand...
Click to collapse
Thats the picture I was talking about that I saw the other day - its not and MTCB/C unit or an MTCD unit.
@ikerg said it was an Ownice unit, AFAIK Ownice was a manufacturer in its own right, so I was either wrong or, as I said, maybe its just coincidence and the "KLD" is not related to the manufacturer Klyde who make MTCB/C/D units.
So I d advise checking the Ownice threads in the Android Headunit General forum.
typos1 said:
Thats the picture I was talking about that I saw the other day - its not and MTCB/C unit or an MTCD unit.
@ikerg said it was an Ownice unit, AFAIK Ownice was a manufacturer in its own right, so I was either wrong or, as I said, maybe its just coincidence and the "KLD" is not related to the manufacturer Klyde who make MTCB/C/D units.
So I d advise checking the Ownice threads in the Android Headunit General forum.
Click to expand...
Click to collapse
No it seems not to be an Ownice unit. Front and back are completely different to mine. Mine is exactly as shown at Klyde. The reset hole is not on top right as in Ownice units, instead it is positioned just on top of the SD-Card slot.
But thanks a lot and sorry again for capturing.
rigattoni said:
No it seems not to be an Ownice unit. Front and back are completely different to mine. Mine is exactly as shown at Klyde. The reset hole is not on top right as in Ownice units, instead it is positioned just on top of the SD-Card slot.
But thanks a lot and sorry again for capturing.
Click to expand...
Click to collapse
I wouldnt go by the reset hole, that can be anywhere.
It was @ikerg that said it was Ownice, he seemed quite certain.
Its deffo not MTC at all, or it would say "MTC" in the MCU field, I m a bit stumped, I normally refer people to the Android Headunits General forums for non MTC units, not sure what to say about yours, a I said I cant say whether the "KLD" means its Klyde or whether its just coincidence.
Maybe try contacting Klyde and asking if its one of their units ? Theyre here :
http://www.szklyde.com/universal-android-car-dvd/
Hello
Got some rather nice LED lights to bling up the family’s day van for Xmas. Work very well but for some reason the android HU won’t see them in Bluetooth in settings the BT/phone app or from the Govee app.
Interestingly when installed the app on my iPhone 7 the govee app saw the LED lights instantly and connected so I can control and change settings.
Just won’t work on the android hu which is a shame.
It’s an LM running Oreo 8 and has no issues finding other devices like OBD11 or other iPhones etc. Just won’t see this led light set.
As noted iPhone connected instantly from the app so it doesn’t seem to be the device itself.
Any ideas how to get the head unit to spot it?, not the end of the world but would be much neater to control the lights from the head unit.
https://www.govee.com/productDetail?sku=H6113&asin=B0798KMJFG
Sent from my iPhone using Tapatalk
i'm wondering if you ever found a solution. Im in the same situation with exactly the same Govee app haha. Would love to know if anyone figured this out
ilker290 said:
i'm wondering if you ever found a solution. Im in the same situation with exactly the same Govee app haha. Would love to know if anyone figured this out
Click to expand...
Click to collapse
Hello nope never sorted it, no one here responded and Govee were no help.
I sold the van and fitted another android 10 unit in my Audi and that won’t connect either so annoying.
Danno1975 said:
Hello nope never sorted it, no one here responded and Govee were no help.
I sold the van and fitted another android 10 unit in my Audi and that won’t connect either so annoying.
Click to expand...
Click to collapse
I have a head-unit from SYGAV in my Toyota. Its android 10. Reaching out to the manufacturer, they came back to me today and said that the likely issue is that the head unit only works as a bluetooth receiver... Thinking I may be SOL and if your head unit is anything similar, then you may be too...
ilker290 said:
I have a head-unit from SYGAV in my Toyota. Its android 10. Reaching out to the manufacturer, they came back to me today and said that the likely issue is that the head unit only works as a bluetooth receiver... Thinking I may be SOL and if your head unit is anything similar, then you may be too...
Click to expand...
Click to collapse
that makes sense actually. All it can connect to is the phone for Streaming and calls and we know the BT in these is rubbish too.
a shame as it would be very cool to control the ambience from the head unit as if factory.
Dears,
anybody tried Eonon GA2178 - 10" Android 9 Head Unit?
I'm actually on Eonon GA2168K - 10" Android 8 Head Unit, it's a good device with minor problems.
Anytime developers fix a problem they introduce an other problem and there's no community support for MTK chipsets.
Because of this I'm evaluating the new Eonon GA2178, that is quite similar but based on Rockchip chipset.
Tks!
Any update on that GA2178 new device? I bought this one as well but have not installed it yet.
Sent from my Pixel 3 XL using Tapatalk
I installed this unit (Eonon GA2178) on my Mitsubishi Montero Sport 2019 on last weekend. It's working great, Loudness setting makes the sound awesome.
Cons:
- I don't like the launcher, probably will use FCC Launcher
- I have not figured out how to connect the steering wheel to SWC1 and SWC2. I think I'm missing the decoder box (Axxess or Metra). I'll buy it on amazon and report back if it works.
Feel free to ask any questions on the install.
I used the Metra. Works good. Sometimes it gets confused and doesn't work but 95% of the time it works.
Sent from my Pixel 3 XL using Tapatalk
I've got a GA2176 and just purchased a GA2178.
I probably should have asked these questions before I bought the new unit but.
Does this come with google play store installed?
Have they fixed the overheating issues? I saw a review where the screen would flicker in heat over 85 degrees.
Has anyone tried the addon dongle that supports android auto and apple carplay?
Google Play Store was installed from the factory. I had to install multiple other Google Apps (I have a Pixel 3 and use them all).
Live in Georgia and we've had a heck of a summer. No overheating issues.
Sent from my Pixel 3 XL using Tapatalk
I have not tried the adapter.
No reviews as of a week or two ago and the company didn't answer my question about how it works or if it would enable the latest version of Android Auto.
I'm very interested but wanted someone else to be the first to try.
Sent from my Pixel 3 XL using Tapatalk
007matman said:
Google Play Store was installed from the factory. I had to install multiple other Google Apps (I have a Pixel 3 and use them all).
Live in Georgia and we've had a heck of a summer. No overheating issues.
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
Thanks. I live in Alabama and you're right. It's been a particularly hot summer( temps hanging in the 100s for multiple days).
I've also been looking around for a root for this unit. Has anyone found anything?
---------- Post added at 08:56 AM ---------- Previous post was at 08:54 AM ----------
007matman said:
I have not tried the adapter.
No reviews as of a week or two ago and the company didn't answer my question about how it works or if it would enable the latest version of Android Auto.
I'm very interested but wanted someone else to be the first to try.
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
Well, when I talk to customer support I was told it will work with the GA2178 so I ordered it with the head unit. Hopefully I'll have it before the week is out and offer some feedback.
I have not seen a way to root yet. I'm sure it's just a matter of time.
I am running FCC launcher and am getting along fine with it. I hated the stock UI.. it's pretty horrible.
I am very interested in hearing your experience with the adapter. Why we'd have to spend another $60 for it to work like it should is beyond me. However, I really would like to have that feature. Let us know what you find out.
Sent from my Pixel 3 XL using Tapatalk
haroldgv said:
I installed this unit (Eonon GA2178) on my Mitsubishi Montero Sport 2019 on last weekend. It's working great, Loudness setting makes the sound awesome.
Cons:
- I don't like the launcher, probably will use FCC Launcher
- I have not figured out how to connect the steering wheel to SWC1 and SWC2. I think I'm missing the decoder box (Axxess or Metra). I'll buy it on amazon and report back if it works.
Feel free to ask any questions on the install.
Click to expand...
Click to collapse
I have a 2010 Dodge Ram and used the PAC RP4-CH11 decoder and the SW switches work very well. You can even program them for short and long pushes. This gives you the ability to control more functions with them.
007matman said:
I have not seen a way to root yet. I'm sure it's just a matter of time.
I am running FCC launcher and am getting along fine with it. I hated the stock UI.. it's pretty horrible.
I am very interested in hearing your experience with the adapter. Why we'd have to spend another $60 for it to work like it should is beyond me. However, I really would like to have that feature. Let us know what you find out.
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
I received the head unit and carplay/android auto dongle yesterday. I tried the dongle with the old head unit, Eonon 2176 installed and it seems to function just like any other iOS carplay stereo. Once I get the 2178 installed I'll do some more testing and let you know what I find and think.
Sounds great man. Thank you.
You don't by chance have an Android Phone to test it with too do you?
Sent from my Pixel 3 XL using Tapatalk
GA2178
I installed my Ga2168 in my Nissan Sentra and I have the dongle as well as usb stick, sd card and front and rear cameras as well as GPS and wifi installed. When I originally got this it ran incredible but the 2x I tried to turn it on it would not. I used the reset whole and it finally turned back on. It ran fine after but then a few days later the same thing it would not turn on. The reset button worked again but I contacted support and they sent me two files to do a complete system reinstall. The problem is not that I reinstalled the os it is so slow everything runs slow to the point I don't want to even use this radio. I will say when I first got the machine it worked fine other than not turning on sometimes. The dongle works perfect with IOS and Android I tested both. I will say I prefer to use my phone as a hotspot and just use the tablet as a giant phone.
007matman said:
Sounds great man. Thank you.
You don't by chance have an Android Phone to test it with too do you?
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
millersnmeva said:
I installed my Ga2168 in my Nissan Sentra and I have the dongle as well as usb stick, sd card and front and rear cameras as well as GPS and wifi installed. When I originally got this it ran incredible but the 2x I tried to turn it on it would not. I used the reset whole and it finally turned back on. It ran fine after but then a few days later the same thing it would not turn on. The reset button worked again but I contacted support and they sent me two files to do a complete system reinstall. The problem is not that I reinstalled the os it is so slow everything runs slow to the point I don't want to even use this radio. I will say when I first got the machine it worked fine other than not turning on sometimes. The dongle works perfect with IOS and Android I tested both. I will say I prefer to use my phone as a hotspot and just use the tablet as a giant phone.
Click to expand...
Click to collapse
One thing I noticed is how these stereos don't like to run well if they are not getting a full 12.8 volts. I left a dash camera on in the parking mode and it ran the battery down to 12.2 volts before shutting off. After that the stereo seem to run slow and was slow to boot. It even had issues with turning on a few times. This was with my old GA 2176 model. I put the battery on a charger and fully charged it and the stereo went back to normal.
edit - of course I go out to my truck this morning and the stereo wont turn on!!! lol the battery is 12.2 volts. I had to use the reset button to get the stereo to start again.
So if you have a weak battery it can cause issues with the stereo.
---------- Post added at 05:14 AM ---------- Previous post was at 05:11 AM ----------
007matman said:
Sounds great man. Thank you.
You don't by chance have an Android Phone to test it with too do you?
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
I don't have an android phone, just a MiPad 4 that I can test with.
I do have an issue with the screen being kind of floppy from side to side. Where it connects to the mount on the main head unit isn't that tight of a fit. I sent an email to Eonon and they want me to make a video of it. I'm going to assume there is nothing they can do about it. I'll probably have to make some sort of a wedge to go between the screen and the head unit.
Mine has a little movement.. not horrible but it would be nice if it was tighter.
Screen isn't very sensitive but I'm used to using my Google Pixel 3 XL.
Seems much more like an old tablet where you had to press hard on the keys to get it to respond.
I am driving an F350 Powerstroke Diesel. It has two 12v batteries so voltage isn't a problem for me.
Sent from my Pixel 3 XL using Tapatalk
Here's the video of the loose screen rattle.
https://www.youtube.com/watch?v=QuDxNKSry4U
I sent it to Eonon CS, NIcky, to see what they say but I'm sure it's going to be sorry, that's just how the mount is.
That's how mine is. Let me know what you find out.
Sent from my Pixel 3 XL using Tapatalk
007matman said:
That's how mine is. Let me know what you find out.
Sent from my Pixel 3 XL using Tapatalk
Click to expand...
Click to collapse
I got a response from eonon, they told me to tighten the screws. As you can see in the video, all of the mounting screws are tight. I told them as much in the first email.
I then got a second email asking me to please make the video private. I can only assume it's to avoid bad press. Well, that isn't going to happen.
Anybody know if this ROM will work on the GA2178? It's for a px30 and from malaysk. Do I have to root first?
https://forum.xda-developers.com/an...-custom-rom-arrive-px30-owners-t3915634/page2
ZERT_TITAN said:
Anybody know if this ROM will work on the GA2178? It's for a px30 and from malaysk. Do I have to root first?
https://forum.xda-developers.com/an...-custom-rom-arrive-px30-owners-t3915634/page2
Click to expand...
Click to collapse
From what I can see it doesn't support the 2178 or 2176 atm. These two HU are rk3326 with 2 mg of memory and the ROMs you link to only support 3368 and 3399 HU with 4 mg of memory.
I just got the GA2178. Has anyone figured out how to unlock developers settings or USB debugging?
Hi fellow XDA members.
My radio GS MCU died due to hardware issues (broken and in not reparable state lanes due my own fault) and i'm searching for a replacement mainboard. Not the SoM with the CPU/MEM/EMMC
It's a VW DVD GS model which i upgraded from PX3 to PX30 to PX5. (Android 5.1, 6.0, 8.0, 9.0) I have contacted several sellers in China but they all reply they cannot deliver me a replacement part due to the age of the hardware. When trying to figure out i noticed that GS still creates mainboards but with an updated layout and chips but the connection ports are still the same. Not sure why they wont deliver me a replacement part.
Does anyone of you have a broken unit but the mainboard OK that i can buy?
Or let me know how i can in contact with the GS Factory. I tried to contact them using their address on the website of the factory but never received a reply.
The pictures included show you the board which is defective.
FlatcablePort layout:
2 ports for the SDcards
1 port for the LCD and its buttons
1 port for the DVD drive.
Thank you for who can help me out in my quest to fix the radio .
Compatible boards:
GS, CHG, XRC-602-MAIN
I'm from the Netherlands/Belgium.
Looks like a GS board Have you had a look on aliexpress, I see there are a number of resellers selling main boards.
The other option is to try Xtrons, you'll need their model code however. I was able to get a GS board out of xtrons quoting their model number a couple of years ago.
Also, consider an HA board from Dasaita - as long as the rear connector layout is the same, you should be ok.
marchnz said:
Looks like a GS board Have you had a look on aliexpress, I see there are a number of resellers selling main boards.
The other option is to try Xtrons, you'll need their model code however. I was able to get a GS board out of xtrons quoting their model number a couple of years ago.
Also, consider an HA board from Dasaita - as long as the rear connector layout is the same, you should be ok.
Click to expand...
Click to collapse
That it is a GS board, that i already knew It was delivered with a PX3 5.1 board and i updated the MCU in the past.
The seller who sent me the device was contacted but he blocked me off with the message: They dont make that radio anymore so no repair parts. Which i think is a BS story but hey who can blame them. Why selling parts when you can sell a complete unit..
I tried several resellers but almost all denied or didnt answer. They only sell complete sets. I'm only able to find the board from the Dasaita, which is not compatible with my system due to the missing ports for the second SD and DVD player. (The one i found on Aliexpress)
Xtrons was the first and only one to reply willing to help but due to Corona i only get an confirmation around march.
I do not have a model number of their device which is the same as the one i have. I did sent all the info i had with some hope they can hook me up.
I found the same system but the reseller sees my messages (Aliexpress lets you know) but did not respond.
Link: https://nl.aliexpress.com/item/4000175298519.html
It's the same radio with the Android 5.1 manual, the seller only replaced the SoM's and selling them for the price of the newer systems.
Here's one that might be close enough https://a.aliexpress.com/_snm0Pb
Over priced though, you might be able to negotiate.
What happened with the mainboard, possibly repairable?
marchnz said:
Here's one that might be close enough https://a.aliexpress.com/_snm0Pb
Over priced though, you might be able to negotiate.
What happened with the mainboard, possibly repairable?
Click to expand...
Click to collapse
The board is beyond repairable, i made a screw up and its damaged badly.
A response was received by the seller of the same device stating that they do not sell parts.
I found this one, which meets the requirements and contacted the seller.
https://nl.aliexpress.com/item/32879522002.html
This one also denied.
Update 12-02-2020.
I figured out that a CHG board is also compatible.
Nobody has a board available? I contacted several resellers but all did reply that they did not sent out parts and even the seller where i did get the unit from denied to sent a repair part and wanted me to order a complete new unit..
I apologize if not. I'm desperate for assistance and I hope someone can point me in the right direction. I recently purchased a Dasaita Vivid 10 on Amazon for my 2015 Camry. Few things:
After installation and turning it on, I wasn't presented with the first time user setup. Additionally, there were a few local MP3s on there. Specifically "Hotel California" from The Eagles. Is this normal or was I sold a used unit? The unit itself had the plastic on the screen. ZERO marks that it was used. Everything from my perception was brand new.
However, when I went to connect WiFi, I received the seemingly common error of it turning on and instantly back off again. As such, I did a factory reset. This erased all of the music that was on the device. This leads me to think that it shouldn't come with music...
Each time I turn my car on, the WiFi is a red X on the icon on the bottom right. To resolve this, I need to hctreboot the thing using factory settings. After this, it will work. However this really sucks and I don't want to do this every time I get into my car. Last night I changed the BT setting and I believe it may have fixed the wifi issue. However, this broke Bluetooth. When I loaded up a hardware info application, there was a mac address for WiFi but none for BT. Is there a way to know which module I have to select the right setting?
Can someone explain exactly what I can do to fix this? After searching for hours I am so lost with all of the terms. Vivid, Scout, MAX. I have no idea where to even get a firmware file. What does MTCD stand for? While it may be considered a budget radio, $530 bucks is a big chunk of change for a radio to be this unreliable. I wrote on Dasaita's forums and it looks like they couldn't care less to assist people. Frustrated, and I'd like help here before returning this and returning to the stock unit. I can provide pictures of anything if needed, just let me know!
Thank you all!
Welcome to the world of cheap Chinese origin Android head units and quality issues.
There is no first run, that is normal.
MTCD refers to a type of unit based on HCT design. There are a bunch of factories that produce these and a bunch of resellers, such as dasaita that sell them, applying made up brand names and model codes. Dasaita appear to price their units at a premium.
Suggest returning it for the hardware issue and look to an FYT based unit, which might get you closer to what you want.
I no longer recommend MTCD based units, and have since brought an FYT 7862UIS based device. The bugs are less, superior hardware, fantastic audio and works without all the mods/hacks.
marchnz said:
Welcome to the world of cheap Chinese origin Android head units and quality issues.
There is no first run, that is normal.
MTCD refers to a type of unit based on HCT design. There are a bunch of factories that produce these and a bunch of resellers, such as dasaita that sell them, applying made up brand names and model codes. Dasaita appear to price their units at a premium.
Suggest returning it for the hardware issue and look to an FYT based unit, which might get you closer to what you want.
I no longer recommend MTCD based units, and have since brought an FYT 7862UIS based device. The bugs are less, superior hardware, fantastic audio and works without all the mods/hacks.
Click to expand...
Click to collapse
Aww man, not the news I wanted to hear however it was expected. At this point I might just go back to stock. I really loved how the dasaita fit into my Camry as it looks super OEM and clean.
Do you know of any of the FYT units that look OEM for a 2015 Camry?
Is this FYT: https://www.joyingauto.com/joying-1...radio-replacement-2015-2017-android-auto.html
I have a 2017 Camry and have this head unit:
https://www.amazon.com/SYGAV-Android-Toyota-Carplay-Navigation/dp/B08PKZY28H/ref=sr_1_1
While it's not a FYT unit, I will tell you that it does not have Vivid installed on it and has worked quite well in my Camry for over a year now.
Would be happy to answer any questions about it. I posted a review on Amazon and have answered a few questions over on Amazon as well.
jlbooth said:
I have a 2017 Camry and have this head unit:
https://www.amazon.com/SYGAV-Android-Toyota-Carplay-Navigation/dp/B08PKZY28H/ref=sr_1_1
While it's not a FYT unit, I will tell you that it does not have Vivid installed on it and has worked quite well in my Camry for over a year now.
Would be happy to answer any questions about it. I posted a review on Amazon and have answered a few questions over on Amazon as well.
Click to expand...
Click to collapse
Thanks so much for this! If I can't get my Dasaita working correctly, I will absolutely return and get that one!
Check this firmware recently released:
ha3_rk3399_10.0_ota(20220329+蓝牙MCU专用包).zip
Shared with Dropbox
www.dropbox.com