I have the OnePlus 5t and recently I bought the redmi airdots (Bluetooth 5.0 earphones) and I have some troubles to pair them. Every time i connect to them I get a notification asking me to pair and connect (pairing request), when I press yes, a pop up message appear asking to pair and connect again, then a press yes and it connects normally. the thing is, I had another Bluetooth headset from xiaomi too and when i simply turn on the headset it automatically connects without prompting to pair and connect like the airdots.
my question is, can I get rid of this notification and pop up message asking to pair? I would like to simply turn on my earphones and it automatically connect to my phone without the need to every time confirm to pair (since the earphones already are paired).
I already cleared the cache in the bluetooth app and reset the phone, but still nothing.
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
mazzidev said:
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
Click to expand...
Click to collapse
This fixed the problem. Thank you!
Related
My PDA2k seems to be turning itself off even when in use :?
I use TomTom3 in the car, and even when the power is plugged into the bottom it was turning off ever few minutes.
I just took a phone call and when I has finished talking I noticed the screen had gone blank and pressing the red handset didn't bring it back, the power button did. (I do have screen lock on).
Having said that, thinking about it, I was watching TV progs on WMP on the way home and it never shut itself off once :?:
Anyone have any idea what is going on? Is this normal?
I have an o2 XDA2 S running TomTom 3 with the TomTom cradle. I occassionally find that the pda just turns itself off.
It doesn't happen all the time.
I have also found that sometimes during a call the pda turns itself off and I cant get it back on by pressing the handset key, just the on off button.
Cheers
Fatzzz
click start>settings>system>backlight . . in here you can change the time it takes to turn off in not touched the device, 5 mins max.... also if you click button lock in system settings, you can set it so that when it happens, you can tap screen and it comes back on again.... tho i prefer to keep that off, otherwise it may ring people while it its protective case.. :lol:
and going by all the software that is out for these xda's, you can prob find a programe /or hack to change it even longer if you need that!!!
But when it is on external power (plugged into the car using TT3), it shouldn't shut down at all. Aside that, when in use (when receiving a call) I wouldn't think it should shut down should it?
I have a seperate scren lock installed too. I found the built in one not enough. When it is in my belt pouch and I get a text, or connect to my BT car kit or something, it wakes it up. All of a sudden all the keys are being pressed (by the squeeze of the case) and all kinds of applications are opening!
Is anyone else having issues with Traveler in WM6?
I'm using an AT&T based Pandora Kitchens ROM and I'm getting the following problems:
1. Screen is off, I press the power button to turn it on. The screen turns on and I see my Today screen or whatever program I was using when I turned it off but that's it, I can't do anything else. Screen and buttons don't respond. Pressing the call end button results in the short beep that it normally sounds when you're on the Today screen and press it. But I have to soft reset to use my phone.
The same problem happened a few times when someone tried to call me. I was watching my phone when I tested this. Screen was off, I rang myself frlom another phone, the screen turns on and the phone symbol appears next to the signal icon in the top bar but after that the phone freezes as above. Soft reset needed.
2. Phone is charging using the wall adaptor. Green light is on. I pull the power cable out of the phone and press the power button, nothing happens. I had to soft reset.
3. Turn phone on, tap Start menu, wait about 15 seconds before Start menu appears!
Any ideas?
My two day old LiveView just refuses to stay on now. It worked relatively ok for a day with the usual random disconnects but and now, everytime I turn it on it goes into pairing mode and switches off 5 or so seconds later (shows the SE logo and switches itself off).
The only way I can get it to remain on is by holding the top right button. It stays on but as soon as I let it go, bam, it switches off again. The battery is full, I have run the update (had to keep the button held down for that too!), tried to hold the power button for 8 seconds to reset it and basically done everything I can think of to make it work.
Anyone have ideas?
UPDATE - This even happens when I plug it into the charger. It turns on, LED blinks red/green, turns off after 5 seconds and the LED doesnt stay on solid red (charging).
Well a few days ago, like 2 weeks ago, I thougt I lost my SW3 (I use it w / o leash because it broke and there's no replacement for the stainless steel one) but actually it was lost on my travel bag xD
After plug in again it started to charge, but when I tried to turn on (after reach 100%), after the sony and SW3 logo, it turns off, like it has a problem at boot. I tried to repair via Xperia Companion and the process was succesful, but the watch just gets stuck on the same SW3 logo.
Now I think is the battery, but I'm really hoping is not, there are any suggestion guys about what could be happening?
Is it stuck at the 4 dots spinning? If So I have the same problem, I have tried a factory reset, updating the rom via push commands etc I have brought a new SWR50 thats working with ADB debugging enabled this time (Didn't do it on the last one) my question hopefully will help the OP as well can I take a complete clone/rom backup from the working watch then push that to the broken watch (Bare in mind no debugging enabled on the broken one) Also to the OP have you held down the power button to get to the fastboot menu and factory reset/recovery settings? if not then you turn off the watch, press and hold the power button until the "insert usb now" shows, you then press the power button quickly twice to access the recovery menus
The Watergod said:
Is it stuck at the 4 dots spinning? If So I have the same problem, I have tried a factory reset, updating the rom via push commands etc I have brought a new SWR50 thats working with ADB debugging enabled this time (Didn't do it on the last one) my question hopefully will help the OP as well can I take a complete clone/rom backup from the working watch then push that to the broken watch (Bare in mind no debugging enabled on the broken one) Also to the OP have you held down the power button to get to the fastboot menu and factory reset/recovery settings? if not then you turn off the watch, press and hold the power button until the "insert usb now" shows, you then press the power button quickly twice to access the recovery menus
Click to expand...
Click to collapse
I forgot about this thread lol
thanks dude!, A couple times it reached the spinning dots, but not always, sometimes it turned off on the SW3 logo before the dots appear, and actually I tried all those things you mentioned, but it didn't work, also I think my watch is (even more) screwed now xD...
Trying to do a second repair on Xperia Companion, the watch got turned off in mid repair, lending obviously on an error, and also losing the ability of do offline charge so once the battery reach 0, is over...
now when I plug in just stays on the SW3 logo, I still can go to connect USB screen and go to the two clicks menu (and stays on), but every time I try a repair, in the middle of the process disconnects and turns off, I don't know exactly why only when is plugged on the repair process it turns off, even pluged in the PC w/o repair stays connected all the time... bad thing is I don't know if is charging or not, so could stop working anytime
Have you tried to push the update through adb recovery mode?
The Watergod said:
Have you tried to push the update through adb recovery mode?
Click to expand...
Click to collapse
every day I'm more convinced the watch is screwed
If I turn on the watch stays on the SW3 logo all the time (it seems offline charge works after all), I even can go to the "insert USB" screen and stays on all the time, but when I try to push something to the watch, always disconnects, turns off and the process obvioulsy gets interrumpted, I'm losing my hopes xD
I'm using the original charging wire, but tried with other working ones
my sister bought me this smart watch , it came on long enough to program a few this after I charge it and then 10 minutes later it shut off and now it won't come back on or power up , what should I do ?
I have a weird problem with my sw3. When I plugin my watch to a charger nothing shows up but the watch gets heated up. But when I connect it to PC it just keeps turning on and off. Tried various methods available on this site but none of them worked.
My phone has suddenly died today. Unsure how much battery it had when it happened, no issues before.
I lookedat my phone and it appeared to be off but I noticed a notification light flashing. Power button didnt turn the screen on, no volume or softkey interaction either. green LED still flashing (I had just not long before had a message on whatsapp so maybe it was from this).
Whatsapp web shows phone as offline, google shows phone as offline.
Connect it to USB and the laptop notices a device as I get the noise, but doesnt show as a drive in the laptop
connect it to power, nothing comes on the screen.
Call it and it doesnt ring (noise wise or screen)
Cannot reset - power button feels soft (not clicky)
Light still flashes.....
Really stuck any help appreciated.
galaxys3bluetooth said:
My phone has suddenly died today. Unsure how much battery it had when it happened, no issues before.
I lookedat my phone and it appeared to be off but I noticed a notification light flashing. Power button didnt turn the screen on, no volume or softkey interaction either. green LED still flashing (I had just not long before had a message on whatsapp so maybe it was from this).
Whatsapp web shows phone as offline, google shows phone as offline.
Connect it to USB and the laptop notices a device as I get the noise, but doesnt show as a drive in the laptop
connect it to power, nothing comes on the screen.
Call it and it doesnt ring (noise wise or screen)
Cannot reset - power button feels soft (not clicky)
Light still flashes.....
Really stuck any help appreciated.
Click to expand...
Click to collapse
Could it be possible you have a power button hardware failure. Try this : keep volume down pressed. If the phone reboots the power button is pressed too without you touching it.
Mr Hofs said:
Could it be possible you have a power button hardware failure. Try this : keep volume down pressed. If the phone reboots the power button is pressed too without you touching it.
Click to expand...
Click to collapse
I did think that the power button may have failed, but noting that the notification light is on, that then suggests the phone is in a powered on state - if that is the case should it not respond to an inbound call, any of the soft buttons at the bottom etc?
Just tried holding volume down for 15 seconds, nothing.....
Was hoping to get the phone to completely power down of its own accord but I dont recall if it had 3% or 70% and dont know how long a blinking LED will keep it going for!