Hi all,
My XDA IIs works well before. But few days ago the Power button doesnt work properly, it can turn on the phone, hold to turn off the back light, but I can't use it to turn my phone screen off like before. Anyone has same problem ?
Can you see any part of the screen? It might just be that the backlight adjustments are set too low when the unit isn't cradled. You might be able to see the screen in daylight.. or maybe it was inside your home. I forgot where I was at when it happened to me. In anycase, if you can see a bit of images on your screen, go into the Backlight properties and change the setting to your liking.
Good luck..
The problem is i can just press the power button to turn off my phone BEFORE (the screen is completly off), and NOW it doesnt work at all ! When my phone was off, I can press the Power button to turn it on, or when I hold it for few seconds the back light will be turned off, but press once to turn off. I dont know why, if somthing wrong with the Power button it should be doesnt work at all, that's mean i cannot turn on my phone as well. But other functions of the Power button are still work well, except the 'Turn off' :roll:
power off doesn't work anymore
I have the same problem here. I can't use the power button to power off my qtek 9090!!
i can use the power button to turn my pda on and to switch the background light on and off - so the "hardware side" of the power button is working.
however, i can't use the power button to turn off the device. it's very annoying, because i can't put it in my pocket after finishing a call :-(
this should be some sort of a software problem - so i hard resetted my device (a couple of times) - but that didn't help!
can anyone help?
thanks,
lorenz
the ba doesn't turn off it is always on staand by mode. ->settings -> system -> button lock
this will stop any missed call because when the ba is in standby the power button is the only one to work
power on is no problem. i can't put my BA into standby mode. if i press the power button while the BA is turned on, nothing will happen. the screen will stay on, the background light stays on.
i have no way to put it into stand-by with the power button!
try this and see if it works. it's a software app that wil rest, shut down, and turn the screen off. just copy it to your BA temp directory and install it.
power button problem
nemchua
Is your problem solved ?
Because I have the same problem.
Power of switch doesn't work !!!
Any help would be welcome.
power button problem
Does anyone solve the problem???
Had the same problem...
I had the same problem going on for about two weeks or so...never changed anything and it went away all by itself.
The problem has not come back now in over 4 months.
Sure would love to know what the problem was tho...
Greetings,
Noddy
Power Off does not work
Add my name to people with this problem.
The only event I can link it to is this: I deleted my Motorola Bluetooth headset and installed a Logitech headset. I noticed the problem (can't turn OFF with POWER BUTTON) soon after that.
same problem for me ..... someone must know !!!!
I think it is a hardware problem. The contact is not making cleanly. Disassemble and spray time, perhaps.
It's a standard push switch, easy enough to replace, I occasionally list themon ebay but any phone repairier should have them in stock.
Richard
i had same problem yesterday afternoon, but it is ok now. recovered by himself
Write again in two weeks and let us know if it is still healthy. In my case, anintermittent problem became continuous.
Can't turn the screen on after pressing power button
I have a problem with my Bell Atrix. After pressing power button to lock the screen, i can't wake up the screen up by pressing that button again. Could anyone tell me how to fix it pls.
Is anyone else having issues with Traveler in WM6?
I'm using an AT&T based Pandora Kitchens ROM and I'm getting the following problems:
1. Screen is off, I press the power button to turn it on. The screen turns on and I see my Today screen or whatever program I was using when I turned it off but that's it, I can't do anything else. Screen and buttons don't respond. Pressing the call end button results in the short beep that it normally sounds when you're on the Today screen and press it. But I have to soft reset to use my phone.
The same problem happened a few times when someone tried to call me. I was watching my phone when I tested this. Screen was off, I rang myself frlom another phone, the screen turns on and the phone symbol appears next to the signal icon in the top bar but after that the phone freezes as above. Soft reset needed.
2. Phone is charging using the wall adaptor. Green light is on. I pull the power cable out of the phone and press the power button, nothing happens. I had to soft reset.
3. Turn phone on, tap Start menu, wait about 15 seconds before Start menu appears!
Any ideas?
Since 2 months, i am facing this issue where the phone dosent allow the battery to charge, thinking that the phone's battery is dead - i replaced it with a new one, but the phone still dosent boot, what happens is that when i press the PWR button on the phone i see the first screen with the red light blinking, and then turns off, but when i try to pwr on the phone with the PWR cable plugged in it works fine,
can any help me on the possible issue on the phone,
I hope I'm posting this in the right place but I'm desperate for help.
My phone, HTC 10, froze and then the screen turned off while I was taking a picture.
The charge should have been around 80%.
Symptoms:
The screen is unresponsive.
Couldn't get the home button/finger print sensor to turn the screen on.
Couldn't get the power button to turn the screen on.
A call to my phone could not reach my number as well.
When plugged in to a wall charger or laptop no indicator light turns on.
When connected to a laptop, the laptop makes that connection noise and a long name with QualComm in it shows up.
Tried Power Button + Volume Up for 10 seconds but didn't get any result.
Side note:
The power button was a little faulty before as well.
You have to squeeze it a certain way to make it work.
I need to somehow restart my phone. Any ideas?
PointOfViewGun said:
I hope I'm posting this in the right place but I'm desperate for help.
My phone, HTC 10, froze and then the screen turned off while I was taking a picture.
The charge should have been around 80%.
Symptoms:
The screen is unresponsive.
Couldn't get the home button/finger print sensor to turn the screen on.
Couldn't get the power button to turn the screen on.
A call to my phone could not reach my number as well.
When plugged in to a wall charger or laptop no indicator light turns on.
When connected to a laptop, the laptop makes that connection noise and a long name with QualComm in it shows up.
Tried Power Button + Volume Up for 10 seconds but didn't get any result.
Side note:
The power button was a little faulty before as well.
You have to squeeze it a certain way to make it work.
I need to somehow restart my phone. Any ideas?
Click to expand...
Click to collapse
Try to clean all buttons really well, if it keeps failing to boot and the phone is still recognized as Qualcomm it's probably bricked.
Simple explanation of the word bricked :
When the phone doesn't boot, when you can't access the bootloader, download mode or recovery it's bricked!
Mr Hofs said:
Try to clean all buttons really well, if it keeps failing to boot and the phone is still recognized as Qualcomm it's probably bricked.
Simple explanation of the word bricked :
When the phone doesn't boot, when you can't access the bootloader, download mode or recovery it's bricked!
Click to expand...
Click to collapse
Strange turn of events: I plugged the phone to my laptop because I read somewhere that it drains the battery. Just for the kicks, after a few hours, I unplugged and re-plugged my phone. Suddenly, there was light. The battery light came back. I immediately switched to the wall charger and once I did that the battery icon appeared showing 1%. Now, it's peacefully charging away. Will see if it actually turns on later on once it's charged about half an hour.
Background -
I bought this OnePlus 5T with a smashed screen to fix.
Paid 70 bucks for it plus the screen is just shy of 150 in total.
I was able to replace the screen and frame which was a little more complicated than I anticipated, but it ended well and the phone seems fine, although the screen quality isn't as good as stock.
***Problem - it seems that for unknown reasons, after turning off the screen pressing using the power button, screen becomes black and won't turn on, not until i hold the power button for ten seconds and restart the phone the hard way. Then the phone turns on and starts working again, but if I turn the phone off with the power button then it won't turn on again. I can tell the phone is working behind the black screen, vibration working, notification light working. But Everytime I turn the phone off with the power button I have to hard reboot the phone to get it back on again. Once this starts happening I have to factory reset to get the power button functioning normally again. It will work normally for a day or two and then out of no where the issue comes back again after pressing the power button - screen won't turn on.
Could it be software? I know it might be natural to suspect the screen is faulty, but the screen works normally until I use the power button to turn it off, and then works normally again for a couple of days after a factory reset ...
Thoughts ?