Powering up Z5 Premium with no working volume and power buttons - Xperia Z5 Premium Q&A, Help & Troubleshooting

Hey everyone, is there any way out to power up, or enter flashmode or even fastootmode with broken all hardware buttons using for example adb commands?

_Barti2605_ said:
Hey everyone, is there any way out to power up, or enter flashmode or even fastootmode with broken all hardware buttons using for example adb commands?
Click to expand...
Click to collapse
Try flashtool witf fastboot mode.
Open flashtool,
Click lightning button
select fastboot mode
Reboot device into system
and press volume up
plug cable

Here's catch none of hardware buttons were working.
But I founded another solution, when I pressed upper side of phone using my hand, the buttons were working, therefore after that everything has been solved.
Thx for reply anyway
Peace Buddy

_Barti2605_ said:
Here's catch none of hardware buttons were working.
But I founded another solution, when I pressed upper side of phone using my hand, the buttons were working, therefore after that everything has been solved.
Thx for reply anyway
Peace Buddy
Click to expand...
Click to collapse
Where exactly did you press? i tried everything

Related

Ran task 29, now phone is stuck on bootscreen HELP!!!!!

I ran task 29, and after its done all my phone does is stay at the olds roms startup splash screen!!!! What do i do??? Is it bricked??? Why would someone tell me to do that if it was gonna break my devise??? can someone please help
alroco20 said:
I ran task 29, and after its done all my phone does is stay at the olds roms startup splash screen!!!! What do i do??? Is it bricked??? Why would someone tell me to do that if it was gonna break my devise??? can someone please help
Click to expand...
Click to collapse
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
BeEazy10 said:
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
Click to expand...
Click to collapse
Doesn't that trigger Ramdump mode (well, I don't know what that means, actually)?
All the OP needs is to go to Bootloader Mode to flash a ROM via USB. Bootloader is easily accessed by: Turn off phone, then press/hold Volume Down + Power button.
thanks guys, ive been using android, and never a minmo device, thanks everyone!!
sumflipnol said:
Doesn't that trigger Ramdump mode (well, I don't know what that means, actually)?
All the OP needs is to go to Bootloader Mode to flash a ROM via USB. Bootloader is easily accessed by: Turn off phone, then press/hold Volume Down + Power button.
Click to expand...
Click to collapse
Yes that mode what ever its called
If you read the sticky posting on Task29, you would see it tells you that this is normal behavious for Task29, and it also tells you how to get out of it
steviewevie said:
If you read the sticky posting on Task29, you would see it tells you that this is normal behavious for Task29, and it also tells you how to get out of it
Click to expand...
Click to collapse
Sortof. I just tried task29 for the first time a few days ago. I freaked out when I got in the same situation as him, but then read through the thread. There's the option of shutting the phone off, and pressing vol down + power key. I ended up doing vol down + power key + push reset with stylus at the startup screen. Simplest solution for me.
taking off the battery, istnt that simplest?
Amd here is the theme about this
raz1337 said:
Sortof. I just tried task29 for the first time a few days ago. I freaked out when I got in the same situation as him, but then read through the thread. There's the option of shutting the phone off, and pressing vol down + power key. I ended up doing vol down + power key + push reset with stylus at the startup screen. Simplest solution for me.
Click to expand...
Click to collapse
In the very first posting of the Task29 thread, it says :
When phone boots to "Touch Pro 2" screen (or whatever your splash screen happens to be), I hold down the volume down button while hitting the reset button.
Click to expand...
Click to collapse
IMO, the smartest thing to do is when Task29 is near 100% (I think it pauses at around 96%), hold down the Volume Down button. That way, when the phone (tries to) reboots, it goes straight to Bootloader.
thanks all you have been more than helpful, ive been using this site for a while (for my android device) but just recently made an account. All of you keep on getting it done!!!
Moved as not ROM Development.
BeEazy10 said:
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
Click to expand...
Click to collapse
Hey, I have a Touch Pro2 and I tried the key combination above and it didn't work for me. I did get it to work however using the send key (green button) instead of the end key....
I.e, held volume down button, held send key and pressed power key once... ;-)
Phone MUST be off before doing the key combo...

flashed wrong kernel

guys unfortunately i just flashed xperia Z kernel using fasboot in my beloved xperia zl..now it is not booting up,only red light glowing...i think it is dead please help..
vivekrules said:
guys unfortunately i just flashed xperia Z kernel using fasboot in my beloved xperia zl..now it is not booting up,only red light glowing...i think it is dead please help..
Click to expand...
Click to collapse
Calm dowm man, i already did that **** once kkkkkk
Simple: Hold down the reset buton till your cellphone vibrate 3 times (That hide one beside your SD Card). That'll turn it off. So hold down your Volume ( - ) button and plug your USB, now you are in flash mode.
Open Flash Tools and flash a Stock ROM (Recommended) or Stock Kernel, That's it!
viniciusnc said:
Calm dowm man, i already did that **** once kkkkkk
Simple: Hold down the reset buton till your cellphone vibrate 3 times (That hide one beside your SD Card). That'll turn it off. So hold down your Volume ( - ) button and plug your USB, now you are in flash mode.
Open Flash Tools and flash a Stock ROM (Recommended) or Stock Kernel, That's it!
Click to expand...
Click to collapse
thanks for your reply buddy..but nothing is happening when i press that yellow reset button beside my sd card
vivekrules said:
thanks for your reply buddy..but nothing is happening when i press that yellow reset button beside my sd card
Click to expand...
Click to collapse
You need to hold it down till it vibrate three times.
No fear, only hold it down
viniciusnc said:
You need to hold it down till it vibrate three times.
No fear, only hold it down
Click to expand...
Click to collapse
Thanks a ton buddy..u saved my A**:good:
vivekrules said:
Thanks a ton buddy..u saved my A**:good:
Click to expand...
Click to collapse
Sorry for bumping this thread, but I got exactly the same problem described by OP. But I simply can't get into the flashmode.
When I hold the volume (-) button and plug the cable at the phone, I got nothing more than the Windows USB sound and a red led of death on my ZL (C6503).
What I've already did:
1) Pressed the "Off" button beside the SD card slot a lot of times (holding it for a few seconds of course) before trying to get into the flashmode;
2) Tried SUS, PC Companion and Flashtool but couldn't get the flashmode or detected by any of them;
3) Keep it charging for more than 12 hours and all I got is this red led of Death!
Any help is welcome.
Cheers.
Edit:
Got the flashmode holding at the following way.
1) Pressed the "off" button beside the SD card slot for a few seconds and instead the 3 vibrations the red led blinked 3 times;
2) Hold the volume (-) button, connected the USB cable and keep holding for a lot of seconds, you will hear the Windows USB sound disconnecting and connecting a few times, wait until Flashtool recognize it and start flashing.

Fastboot: disturbing problem...

My device is UB and rooted.
It's disturbing me that I cannot enter in fastboot via power on / volume + / plug USB cable, it has absolutely no effect, the rom loads.
However, I can enter in fastboot via adb command or with APM+ xposed module from lollipop.
It's disturbing me very much because if one day my device is soft bricked, I will not be able to enter in fastboot mode...
Any suggestions, ideas, solutions ??
Thanks in advance.
nreuge said:
My device is UB and rooted.
It's disturbing me that I cannot enter in fastboot via power on / volume + / plug USB cable, it has absolutely no effect, the rom loads.
However, I can enter in fastboot via adb command or with APM+ xposed module from lollipop.
It's disturbing me very much because if one day my device is soft bricked, I will not be able to enter in fastboot mode...
Any suggestions, ideas, solutions ??
Thanks in advance.
Click to expand...
Click to collapse
You shouldn't power it on when connecting it to fastboot. Let it be off, hold volume up and connect to PC. Wait until the blue light and release the volume up
KbaB.BroS said:
You shouldn't power it on when connecting it to fastboot. Let it be off, hold volume up and connect to PC. Wait until the blue light and release the volume up
Click to expand...
Click to collapse
My bad, it works !! No power on !!!
Thnanks
By the way, I've a Z5, not a Z5P, I got the wrong forum, but nevermind...
KbaB.BroS said:
You shouldn't power it on when connecting it to fastboot. Let it be off, hold volume up and connect to PC. Wait until the blue light and release the volume up
Click to expand...
Click to collapse
My bad, it works !! No power on !!!
Thanks
By the way, I've a Z5, not a Z5P, I got the wrong forum, but nevermind...
nreuge said:
My bad, it works !! No power on !!!
Thanks
By the way, I've a Z5, not a Z5P, I got the wrong forum, but nevermind...
Click to expand...
Click to collapse
Some say the P stands for Plus

Recover files from dead OP3

So today my OP3 officialy died!
My screen is not working anymore and my phone is encrypted, what I would like to do is recover my files.
Is there any posibility to recover them? Unlock phone with ADB, any programms,...
I can not press on anything on my phone (not responding)
I have tried a lot but nothing seems to work, please guys I neeed your help.
What can I do?
?
Just hold down the power button for 20 second then plugin USB to PC holding the volume up button if the PC can detect any kind of device then I can help you.
Sohag0910 said:
Just hold down the power button for 20 second then plugin USB to PC holding the volume up button if the PC can detect any kind of device then I can help you.
Click to expand...
Click to collapse
What I do is, hold power button for 20sec. After that volume up while connecting to pc.
Nothing shows up ):
Kurii38 said:
What I do is, hold power button for 20sec. After that volume up while connecting to pc.
Nothing shows up ):
Click to expand...
Click to collapse
Make sure you check the Device manager for a qualcomm device, not the windows file explorer.
strumaticjoker2 said:
Make sure you check the Device manager for a qualcomm device, not the windows file explorer.
Click to expand...
Click to collapse
Nope, still nothing

[D5503] Frustrated by device not rebooting in cmd window - Flashtool recognizes...

Hi there,
I've done this numerous times and various machines.
Unfortunately my devices on/off button is broken and when the battery is low and the phone shuts down I need a PC to reboot the device by using "fastboot reboot."
Works on 4 different machines, except for my homebase PC. *Sigh* :crying:
In a command window fastboot responds with "waiting for device"..... Opening the Flashtool, it recognizes the device and tells me that it is in the fastboot mode. To my surprise there is no button in Flashtool that says reboot or a chance to issue commands to the phone...... so frustrating.
Any idea of how I can get this to work? Here is what I will not do: Re-Install Windows.
Here is what I tried: Re-Installing the driver numerous times, Flashtool recognizes the device.
How can that be? Makes no sense to me at all....
Any input is appreciated.
Thanks
James
Andro1dism said:
Hi there,
I've done this numerous times and various machines.
Unfortunately my devices on/off button is broken and when the battery is low and the phone shuts down I need a PC to reboot the device by using "fastboot reboot."
Works on 4 different machines, except for my homebase PC. *Sigh* :crying:
In a command window fastboot responds with "waiting for device"..... Opening the Flashtool, it recognizes the device and tells me that it is in the fastboot mode. To my surprise there is no button in Flashtool that says reboot or a chance to issue commands to the phone...... so frustrating.
Any idea of how I can get this to work? Here is what I will not do: Re-Install Windows.
Here is what I tried: Re-Installing the driver numerous times, Flashtool recognizes the device.
How can that be? Makes no sense to me at all....
Any input is appreciated.
Thanks
James
Click to expand...
Click to collapse
Which driver install method do you use? I think Flash tool driver exe is best, and make sure to install fastboot, flash mode, and device specific, (Z1c is 'Rhine'). It's strange that Flash tool would recognize device in fastboot mode, but fastboot wouldn't...
Anyway, an alternative would be to mod system ui to include power button on navbar. Not hard to do. Let me know if you want to try.
Here's an example - https://forum.xda-developers.com/showpost.php?p=71219730&postcount=2212
I changed my on-off button. It's easier
levone1 said:
Which driver install method do you use? I think Flash tool driver exe is best, and make sure to install fastboot, flash mode, and device specific, (Z1c is 'Rhine'). It's strange that Flash tool would recognize device in fastboot mode, but fastboot wouldn't...
Anyway, an alternative would be to mod system ui to include power button on navbar. Not hard to do. Let me know if you want to try.
Here's an example - https://forum.xda-developers.com/showpost.php?p=71219730&postcount=2212
Click to expand...
Click to collapse
Hi Levone,
yeah, I did exacly that. Use Flashtool and then install fastboot, flash mode and the Z1C Drivers..... funny it workes smooth under Windows 7 but not at all under Windows 10 (different partition). I had the hope it goes smooth in Win10 which would suffice for me..... although I'd like to have it running in my home OS Win7x64.
Ur UI looks nice, although I dunno what help it would provide me if the phone is down
alf-endy said:
I changed my on-off button. It's easier
Click to expand...
Click to collapse
Yeah sure that would be no problem from the technical side, but I prefer the phone to be water proof :yay: #SonyForTheWin ^^
Andro1dism said:
Ur UI looks nice, although I dunno what help it would provide me if the phone is down
Click to expand...
Click to collapse
Right - I just thought that if you at least gave yourself a reboot option while phone was up, you could avoid some of the power-downs. I guess you could do thebsame with an app...
Also, might be possible to re-map and make a different button power.
levone1 said:
Right - I just thought that if you at least gave yourself a reboot option while phone was up, you could avoid some of the power-downs. I guess you could do thebsame with an app...
Also, might be possible to re-map and make a different button power.
Click to expand...
Click to collapse
Andro1dism said:
Ur UI looks nice, although I dunno what help it would provide me if the phone is down
#SonyForTheWin ^^
Click to expand...
Click to collapse
O looked into it for my own curiosity, and I wastable to remap my volume key to work for power, by modding /system/usr/key layout, but doesn't work from powered off. Doesn't seem possible...
levone1 said:
O looked into it for my own curiosity, and I wastable to remap my volume key to work for power, by modding /system/usr/key layout, but doesn't work from powered off. Doesn't seem possible...
Click to expand...
Click to collapse
Is there a way to re-calibrate the battery so that it at least shows 20% of power and not 50% ?
Besides: How can I "avoid some of the power-downs" with a reboot?!
But. . . . . . . There are buttons in Flashtool to do what you want
Andro1dism said:
Hi there,
I've done this numerous times and various machines.
Unfortunately my devices on/off button is broken and when the battery is low and the phone shuts down I need a PC to reboot the device by using "fastboot reboot."
Works on 4 different machines, except for my homebase PC. *Sigh* :crying:
In a command window fastboot responds with "waiting for device"..... Opening the Flashtool, it recognizes the device and tells me that it is in the fastboot mode. To my surprise there is no button in Flashtool that says reboot or a chance to issue commands to the phone...... so frustrating.
What about the Fastboot Toolbox in Flashtool ?
Just in case you didn't notice 9 buttons you can push with a mouse to make your xperia do just about anything fastboot can do without ever having to touch a keyboard or a button.
Picture with Sony D5503 Lineage CM12 min res 2mp
Click to expand...
Click to collapse

Categories

Resources