My verizon gnex usb charging port was acting wonky for a bit, so I had to angle the cord a certain way for the phone to charge. I saw the thread on here (via lifehacker I think) that said to bend the "tab" thing that can be seen inside the port upwards. That actually helped and the phone was charging fine for a week or so. Then a few days ago it just totally went kaputt and wont charge at all.
I called verizon and they wont help at all since my 1 year manufacturers warranty was up in december. And their customer service is really just a sales team as their first suggestion was to buy a new battery and "try" that, then they suggested I buy one of their used samsung galaxy stellar (Never even heard of it!) for $250.
So does anybody have any suggestions on how I could repair/replace the port myself, or get verizon or samsung to fix it?
sd0070 said:
My verizon gnex usb charging port was acting wonky for a bit, so I had to angle the cord a certain way for the phone to charge. I saw the thread on here (via lifehacker I think) that said to bend the "tab" thing that can be seen inside the port upwards. That actually helped and the phone was charging fine for a week or so. Then a few days ago it just totally went kaputt and wont charge at all.
I called verizon and they wont help at all since my 1 year manufacturers warranty was up in december. And their customer service is really just a sales team as their first suggestion was to buy a new battery and "try" that, then they suggested I buy one of their used samsung galaxy stellar (Never even heard of it!) for $250.
So does anybody have any suggestions on how I could repair/replace the port myself, or get verizon or samsung to fix it?
Click to expand...
Click to collapse
Edit: do they make a 3 pin charger? How bout an external battery charger?
You can buy a charging port off eBay. I bought one there for $16 with free shipping. Had to come from China, but I had mine in less than a week. Directions for procedure can be found on ifixit.
kyoteqwik said:
You can buy a charging port off eBay. I bought one there for $16 with free shipping. Had to come from China, but I had mine in less than a week. Directions for procedure can be found on ifixit.
Click to expand...
Click to collapse
Thanks, I just found that ifixit article in the meantime. There are no reassembly instructions though which turned me off. I consider myself pretty capable at following instructions but dont have much experience in electronics. How difficult was it for you?
I was able to get mine working again, so I haven't actually replaced mine yet. I used a needle and cleaned all around the charging port, and also gently scratched pins with needle. Would recommend pulling battery if you should try this. It has been about a month and so far no more problems for me.
I have had the phone apart a few times and it doesn't look too bad though.
My USB port has been bad for at least six months. I tried fixing it and ended up shorting something inside the phone. Even the 3 prongs won't charge my phone. Says it is charging but battery won't charge. My solution. Bought two extra batteries and external charger. Love it. Battery dies and just throw in a new one and instantly at 100 percent. You could find a cell phone repair place and they can change the port. No soldering needed on this phone. Just make sure they order the vzw port and not the GSM. They are not the same.
thank you!
kyoteqwik said:
I was able to get mine working again, so I haven't actually replaced mine yet. I used a needle and cleaned all around the charging port, and also gently scratched pins with needle. Would recommend pulling battery if you should try this. It has been about a month and so far no more problems for me.
I have had the phone apart a few times and it doesn't look too bad though.
Click to expand...
Click to collapse
So far this solution has worked for me. I pulled my battery and gently scratched the top of the pins. The phone now charges like it is supposed to. The port must get I build up of gunk in there.
Thanks for your tip
Hi there.
My Mother has a One V which she is really happy about. But recently she says that it has been draining the battery so fast. At first i didnt really believe it (you know old people and tech), and asked if she had charged it correctly. She then told me that the charging process was also quite strange.. She had plugged it in one night, and the phone displayed that it was charging.. Then 8 hours after, in the morning it had only charged 2% ! This doesnt happen all the time, but only some times.
Now she has given it to me and hope that i can fix it. At first im just going to factory reset it, even though i dont think that is the problem. But i have noticed that what she is telling me is true to some extend. I have had the phone sitting on the table all night. No simcard and no nothing.. It had only used about 5%, but as soon as i began using it, to take backup and prepare for the reset oh boy.. It uses 1% in merely seconds! Approx 26 seconds per 1%!
I think this is rather strange and im unsure if the battery is the problem.. Do you guys have any ideas ?
Oh and i have to say that the phone is running newest stock software. It has never been rooted or anything like that.
Well, the charger port is probably bad. My first htc one m8 and my droid incredible 2 both have weak ports on them from the factory. Send it in for warranty and say nothing < about a possible bad charging port if it still has warranty. And, if nothing Less try a brand new charger, and see if that one works and if it's loose when it's plugged in. If it Is loose with new charger it's a bad charger port.
Yeah this confuses me as well. It happens once every few months. The battery drains really fast and charging is extremely slow. The first time this happened my One V dropped from 100% to 27% in 20 minutes! And just like it randomly happens it randomly goes; battery consumption goes back to normal after a day or two.
A possible reason is the charger and USB cable that is used. My cable is worn out so that might be why charging is slow but it doesn't explain why the battery drains so fast even when the phone is disconnected from the charger. So the only reasonable explanation would be some hardware problems in the battery pack.
But this is all just me guessing... I don't know for sure.
tylerleo said:
Well, the charger port is probably bad. My first htc one m8 and my droid incredible 2 both have weak ports on them from the factory. Send it in for warranty and say nothing < about a possible bad charging port if it still has warranty. And, if nothing Less try a brand new charger, and see if that one works and if it's loose when it's plugged in. If it Is loose with new charger it's a bad charger port.
Click to expand...
Click to collapse
It could be the charger port. I tried cleansing it with a toothpick (heard dust could be the problem), but the problem persists
swhatevers said:
Yeah this confuses me as well. It happens once every few months. The battery drains really fast and charging is extremely slow. The first time this happened my One V dropped from 100% to 27% in 20 minutes! And just like it randomly happens it randomly goes; battery consumption goes back to normal after a day or two.
A possible reason is the charger and USB cable that is used. My cable is worn out so that might be why charging is slow but it doesn't explain why the battery drains so fast even when the phone is disconnected from the charger. So the only reasonable explanation would be some hardware problems in the battery pack.
But this is all just me guessing... I don't know for sure.
Click to expand...
Click to collapse
The problem here is that it happens every second time or so the phone is charged at the moment. But i have bought a new battery and will try and change it. Ill write here how it goes and if there is a improvement, so that you know where the problem relies if you are thinking about doing the same.
Same problem here. Every few months the battery drops from > 50% to 2% or so. This happens within some minutes and my phone gets really hot.
But normaly I use it with a 2 amp charger and I think this happens more often if I use chargers with 1 amp.
Edit: This happened for me with every rom I used.
I changed the battery two days ago, and i can already feel a huge improvement.. 8 hours ago i took it out from the charger. Data and Bluetooth has been on all day. Been browsing a little, and sent som SMS and stuff like that.. 65% now.
The conclusion must be that in my case at least, it was a battery hardware fault.
I'm also thinking about replacing my battery, was replacing it easy?
jonas2790 said:
I'm also thinking about replacing my battery, was replacing it easy?
Click to expand...
Click to collapse
Yes it was actually pretty easy. Although i have done it on my One S too, and that was even easier.
Some recommendations: Get your self a repair tool kit before you start. Everything has been so much easier for me after i got that. It is all the money worth it . This is what i got http://www.ebay.co.uk/itm/261399617620?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT <- They ship worldwide.
The battery i brought : http://www.ebay.co.uk/itm/321303229844?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
First i took the plate off at the bottom of the phone (the one where there behind is sim card and sd card). Unscrewed all six screws. Once done you can take all the plastic off the large plastic part (the one below the simcard and sd card when inserted, and covering everything behind the outer cover). This part is also taped/glued, but should not be a problem to get off.
After you have taken that off, use a pry tool to pry the plate open around the camera lens and flash (beware that this plate is also taped together. Unscrew the last screw behind.
Now comes the tricky part. You need another more solid pry tool to pry the lcd/board out from the front. Use the pry tool in between the screen and the cover of the phone, and all the way around. The LCD and board needs to come out from the phones front.
After that the battery becomes visible. There is nothing special to getting the plug out for it as far as i can remember and should just be pulled towards the battery to get it out. Battery is glue to the inside of the phone, but using the solid pry tool you should be able to get it out. If you order the battery i linked to, it comes with new 3M tape.
Heres a video showing it pretty good i think:
https://www.youtube.com/watch?v=gPasbSobzwA
Da9L said:
Yes it was actually pretty easy. Although i have done it on my One S too, and that was even easier.
Some recommendations: Get your self a repair tool kit before you start. Everything has been so much easier for me after i got that. It is all the money worth it . This is what i got http://www.ebay.co.uk/itm/261399617620?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT <- They ship worldwide.
The battery i brought : http://www.ebay.co.uk/itm/321303229844?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
First i took the plate off at the bottom of the phone (the one where there behind is sim card and sd card). Unscrewed all six screws. Once done you can take all the plastic off the large plastic part (the one below the simcard and sd card when inserted, and covering everything behind the outer cover). This part is also taped/glued, but should not be a problem to get off.
After you have taken that off, use a pry tool to pry the plate open around the camera lens and flash (beware that this plate is also taped together. Unscrew the last screw behind.
Now comes the tricky part. You need another more solid pry tool to pry the lcd/board out from the front. Use the pry tool in between the screen and the cover of the phone, and all the way around. The LCD and board needs to come out from the phones front.
After that the battery becomes visible. There is nothing special to getting the plug out for it as far as i can remember and should just be pulled towards the battery to get it out. Battery is glue to the inside of the phone, but using the solid pry tool you should be able to get it out. If you order the battery i linked to, it comes with new 3M tape.
Heres a video showing it pretty good i think:
https://www.youtube.com/watch?v=gPasbSobzwA
Click to expand...
Click to collapse
Aah so it was the battery pack after all!! Interesting to know.
Glad it worked out for you and thanks for the battery replacement links.
My One V is retired but since the battery is cheap I will buy one and replace it just in case I ever need the phone as backup.
I am making this post so it is more broadly seen by people who have a specific hardware issue.
This solution is for issues specifically with the board being fried or more likely broken solder connection. I found this solution while browsing Chinese Custom Rom threads and apparently it works.
Absolutely it's better to pay a professional reball the broken solder connection.
There is a do it yourself/cheap method that definitely does not involve using an Oven.
I included photos at the bottom of the link and rather than create a redundant post, for something that I have already made : Go here for the Jerry Rig Suggestion
https://forum.xda-developers.com/showpost.php?p=79303956&postcount=72
Good Luck
Make sure you followed all of the unbricking steps here https://forum.xda-developers.com/le-pro3/how-to/unbrick-leeco-phones-leeco-variants-t3847220 before even considering this method..
There are 3 unbricking methods mentioned
Qfil with Flash 2.0 or 1.9 ( Try both)
QPST ( Instructions in first comment of unbricking thread)
Flashbat.all method ( Instructions on Unbrick OP, and in first couple of comments)
Hi
What do you think, can I repair this problem? :
My phone is dead. It is not able to turn on, it just squezing sometimes, if I push the turn on button. The screen is full black since the shut down. No logo no any fastboot screen, nothing. The led light was pale green before the qfil.
drdagi said:
Hi
What do you think, can I repair this problem? :
My phone is dead. It is not able to turn on, it just squezing sometimes, if I push the turn on button. The screen is full black since the shut down. No logo no any fastboot screen, nothing. The led light was pale green before the qfil.
Click to expand...
Click to collapse
I wouldn't bother trying this possible solution unless you are 100% sure that you have broken solder connections. Just because your phone doesnt turn on doesn't mean its the chips. It much more likely that your issue is just the battery.
Also just so you know when the board is fried the phone will still turn on, and will boot to fastboot but not recovery, qfil works but does nothing and if you boot to fastboot and leave it on the fastboot screen the screen will turn to static. At least this is what happens with the majority of chip death issues. However there was one case that I know of on a friends X722 which could not go to fastboot, and that issue ended up being a fried GPU, which this possible fix may resolve.
If you are only getting a black screen leave the phone plugged in overnight ( preferably with a different cable) , After knowing that the phone was charged for long enough what happened? Did the phone get warm at all? Does the phone vibrate?
If the phone does vibrate, try using the QPST method, it's the 2nd post on the Unbricking thread mentioned above in the OP.
Another possible cause of your issue is static, they only way to test and possibly resolved is to unplug the battery from the board and plug back in again. Should you attempt trying this, only use a heat gun to melt the glue holding the screen on...there is alot and a hair dryer will not work, without damaging your LCD.
If I had your issue, I would order a battery and LCD, and swap the battery, there is a good chance it will work. If not you can move on to more drastic solutions such as the one mentioned in the OP. Worse case scenario, you will be out the cost of the battery which is about $7 and LCD which is about $15
Good Luck and make sure you followed all of the steps here https://forum.xda-developers.com/le-pro3/how-to/unbrick-leeco-phones-leeco-variants-t3847220
There are 3 unbricking methods mentioned
Qfil with Flash 2.0 or 1.9 ( Try both)
QPST ( Instructions in first comment of unbricking thread)
Flashbat.all method ( Instructions on Unbrick OP, and in first couple of comments)
I believe I read this thread before, but didn't read it well
This thing here I believe is very important, so much to put it in special color
>>Also just so you know when the board is fried the phone will still turn on, and will boot to fastboot but not recovery, qfil works but does nothing and if you boot to fastboot and leave it on the fastboot screen the screen will turn to static.
I guess it's certain now that I have some harware issue, most probably if GPU is separated from the CPU.
tsongming said:
the board being fried or more likely broken solder connection. I found this solution while browsing Chinese Custom Rom threads and apparently it works.
Click to expand...
Click to collapse
I don't know if it's just me who is unlucky but I have lost yet another USB board. This time the one you sent me burnt up as I connected it to my PC. I don't think it's a cable issue because I was using a high quality USB cable from BASEUS. How could it be that I'm not seeing more complaints like mine?
This time I think it could have been caused by dirt in the port because I'd just returned from my rural area and there I did a lot of work involving dirt. Also, there was a slight shower that got me on my way back and I keep the phone in the pocket with the USB port exposed and looking up. My patience with this phone has just about run out now. This is the worst investment I've ever made on a phone :crying:
Sent from my LeEco Le Pro3 using XDA Labs
twistyplain said:
I don't know if it's just me who is unlucky but I have lost yet another USB board. This time the one you sent me burnt up as I connected it to my PC. I don't think it's a cable issue because I was using a high quality USB cable from BASEUS. How could it be that I'm not seeing more complaints like mine?
This time I think it could have been caused by dirt in the port because I'd just returned from my rural area and there I did a lot of work involving dirt. Also, there was a slight shower that got me on my way back and I keep the phone in the pocket with the USB port exposed and looking up. My patience with this phone has just about run out now. This is the worst investment I've ever made on a phone :crying:
Sent from my LeEco Le Pro3 using XDA Labs
Click to expand...
Click to collapse
Wow, sorry to hear that. I think that those LeEco phones are hit or miss. But it really doesn't seem that they were made to last more that a couple of years. I have fried the usb card myself, when I bought very first leeco, its too easy to fry those cards, and in retrospect the Leeco charge is too powerful. The remaining Leeco that I have left charges much better ( stays cooler) when using my Xiaomi Charger.
I agree that you have had some really bad luck. I would not put any more money into it. you are better off buying a cheap Xiaomi...even a used one. You can find some good deals on Amazon and Swappa. Amazon also has refurbished Samsung phones, and they are highly reliable.
You can get a Galaxy 7 for $139 https://www.amazon.com/Samsung-Gala...s=wireless&ie=UTF8&qid=1573693012&sr=1-4&th=1 and they are really good phones.
Here is a renewed One Plus 6T for $267 https://www.amazon.com/OnePlus-A601...ked+cell+phones+renewed&qid=1573693220&sr=8-4
LG V30 for $177 https://www.amazon.com/LG-Camera-Si...ed+cell+phones+renewed&qid=1573693365&sr=8-21
I bought my daughter an A3 and honestly I can't recommend it enough. For a tight budget I personally feel that this is one of the best deals out there for ony $158 ( $50 less than what I paid 2 months ago) https://www.amazon.com/Xiaomi-A3-64...=sr_1_3?keywords=Xiaomi&qid=1573693435&sr=8-3
It has an Amoled Screen and comes with Android One with zero bloatware. You basically get a custom rom experience with a stock phone. To make matters better Android 10 will be released for the A3 in January. The camera, is light years better than the Le Pro 3 and the processor is honestly fast enough, for most of us. No doubt, its more expensive than just getting another card. But saving yourself from the hassles of these constant issues will make it worthwhile. The only drawback is the screen is 720 instead of 1080. But I swear, if you place in side by side with my Mi8, most people would never guess, that the resolution is a little less. Because it's still an amoled screen.
Best wishes, unfortunately I don't have any more working cards or I would send it to you.
I've learned that quick charge is dangerous. I'm using now an usb meter that doesn't let an output beyond 1.4amps to charge my phone now, it charges pretty quickly in fact and my phone doesn't get hot now (even that I live in a hot area)
tylerciggy said:
I've learned that quick charge is dangerous. I'm using now an usb meter that doesn't let an output beyond 1.4amps to charge my phone now, it charges pretty quickly in fact and my phone doesn't get hot now (even that I live in a hot area)
Click to expand...
Click to collapse
Yeah. The current pushed by the stock leeco charger is either too high (doubtful) or the charging system of the pro 3 isn't designed to handle quick charge 3 very well (most likely). I have used my stock leeco charger to charge my brother's Nokia 8 (Q.C. 3) and it gets just a little warm even with a case on. Also, the leeco charger is Quick Charge 3 certified so they must have made it according to Qualcomm standards.
I think it's the quality of the parts on the phone itself that are substandard. Since this USB board was sent to me by @tsongming and he had used it quite a while, I believe it could have been perfectly fine. My suspicion is that something else could be wrong with my phone like the USB flex cable. The kind of burning I saw must have been caused by power from the battery because the USB 2.0 port I was connecting to on my PC can only provide 2.5 amps maximum. This is not enough in my opinion to completely melt the usb-c receptacle on the phone. (It's very badly burnt). I will just have to charge the battery externally until I figure out whether it's worth investing any more money into this phone.
Sent from my LeEco Le Pro3 using XDA Labs
twistyplain said:
Yeah. The current pushed by the stock leeco charger is either too high (doubtful) or the charging system of the pro 3 isn't designed to handle quick charge 3 very well (most likely). I have used my stock leeco charger to charge my brother's Nokia 8 (Q.C. 3) and it gets just a little warm even with a case on. Also, the leeco charger is Quick Charge 3 certified so they must have made it according to Qualcomm standards.
I think it's the quality of the parts on the phone itself that are substandard. Since this USB board was sent to me by @tsongming and he had used it quite a while, I believe it could have been perfectly fine. My suspicion is that something else could be wrong with my phone like the USB flex cable. The kind of burning I saw must have been caused by power from the battery because the USB 2.0 port I was connecting to on my PC can only provide 2.5 amps maximum. This is not enough in my opinion to completely melt the usb-c receptacle on the phone. (It's very badly burnt). I will just have to charge the battery externally until I figure out whether it's worth investing any more money into this phone.
Sent from my LeEco Le Pro3 using XDA Labs
Click to expand...
Click to collapse
My X722 died because I just plugged in the cable to charge. Although I have to admit that the phone socket was not in optimal conditions because I used a crappy cable, so the last one I was using was charging fine but it had to enter in an specific position in order to quick charge to function. It's probably the charger IC that is damaged, but I haven't had the money to send it to repair.
As far as I know, the motherboards just provide 0.5amp unless you are using an special port that can provide more power.
In my opinion 2.5amp at 5v is not that good either, because it's pushing the limit of most phones at 5v.
I am guessing that buying the original $30 USB board from AliExpress won't buy me much time because they have all been used before. Almost every spare part of this phone is not brand new (except for batteries and screens, I guess).
I think it's time to cut my losses. My pro 3 not only needs a new USB board but also a battery and another high quality USB cable. I might buy all of that for $60 only to have the USB port burn again. It doesn't make any sense to keep pouring money into this phone.
Sent from my LeEco Le Pro3 using XDA Labs
What ? $30 usd ? I've seen it in $2.5 for 2 boards, well, not original of course.
You just need to check that it has the extra IC, because there are ones that doesn't has it... although I don't remember what was for that IC, but you can easy see it that some boards just are missing a chip.
As for the cable, I'm using some EFFE cables (EFFE is the brand) and they are working wonderfully, I bought 3 for $7 usd, they plug in fine and stay in too, they were recommended to me by a friend and I'm very happy with them. They even stop giving charge to my dead phone because they detect somehow that there is a short, well, at least that is what my usb meter tells me, although I don't know how do they manage to do that, I don't really think they have an IC in them.
twistyplain said:
I am guessing that buying the original $30 USB board from AliExpress won't buy me much time because they have all been used before. Almost every spare part of this phone is not brand new (except for batteries and screens, I guess).
I think it's time to cut my losses. My pro 3 not only needs a new USB board but also a battery and another high quality USB cable. I might buy all of that for $60 only to have the USB port burn again. It doesn't make any sense to keep pouring money into this phone.
Click to expand...
Click to collapse
For the record the board that I sent you came from a brand new, LePro 3 not opened bought in the spring 2018. However, I assume that it was made after Leecos public fall. I would guess that it was assembled with C grade parts, because my remaining, working LePro 3 is one of our first Leecos bought in 2016. It's also interesting to note that our 2 remaining X522s are both functioning just fine.
As you said could be the flex cables or just a shoddy soldering job that eventually shortened out the board.
Have you tested the board to be sure that it's not the port itself that is bad?
Another interesting thing to note is that Qualcomm removed Leeco from it's list of approved quick charge device list.
One last reason on why I feel that the charger itself may be part of the problem is that I have a 12 watt portable charger and the Leecos do not get hot at all when using it.
I threw my Leeco charging bricks in the trash after my daughter plugged in my Mi8 for me while I was cooking dinner. Not knowing that I had a preference, she used the Leeco charger.
Later when I checked the phone to see if it was finished charging, I found it was extremely hot, and this phone is rated for QC 4.0. So rather than taking any chances into the trash it went.
tsongming said:
For the record the board that I sent you came from a brand new, LePro 3 not opened bought in the spring 2018. However, I assume that it was made after Leecos public fall. I would guess that it was assembled with C grade parts, because my remaining, working LePro 3 is one of our first Leecos bought in 2016. It's also interesting to note that our 2 remaining X522s are both functioning just fine.
As you said could be the flex cables or just a shoddy soldering job that eventually shortened out the board.
Have you tested the board to be sure that it's not the port itself that is bad?
Another interesting thing to note is that Qualcomm removed Leeco from it's list of approved quick charge device list.
One last reason on why I feel that the charger itself may be part of the problem is that I have a 12 watt portable charger and the Leecos do not get hot at all when using it.
I threw my Leeco charging bricks in the trash after my daughter plugged in my Mi8 for me while I was cooking dinner. Not knowing that I had a preference, she used the Leeco charger.
Later when I checked the phone to see if it was finished charging, I found it was extremely hot, and this phone is rated for QC 4.0. So rather than taking any chances into the trash it went.
Click to expand...
Click to collapse
Wow!! Leeco really must have used grade c parts. I haven't mistreated that board even once since you sent it. That means it only lasted three months! It is just unbelievably negligent for leeco to use these parts. They must have been from the reject pile.
I don't need to test the board because the USB-C receptacle on the phone is completely melted. Connecting a charging cable seems to cause it to heat up fast and start smoking. It might have been a short on the connector that caused it to burn up. I think the quality of the protruding part with the pin connectors is just poor and repeated use loosens the pins which eventually touch.
I'm done with leeco for good now. I was thinking about fixing the phone to sell but that now seems like a lost cause. I'll keep it until it's dead and then take a hammer to it. Even selling it for spare parts might be a loss for me so I'm stuck with it.
Sent from my LeEco Le Pro3 using XDA Labs
twistyplain said:
Wow!! Leeco really must have used grade c parts. I haven't mistreated that board even once since you sent it. That means it only lasted three months! It is just unbelievably negligent for leeco to use these parts. They must have been from the reject pile.
I don't need to test the board because the USB-C receptacle on the phone is completely melted. Connecting a charging cable seems to cause it to heat up fast and start smoking. It might have been a short on the connector that caused it to burn up. I think the quality of the protruding part with the pin connectors is just poor and repeated use loosens the pins which eventually touch.
I'm done with leeco for good now. I was thinking about fixing the phone to sell but that now seems like a lost cause. I'll keep it until it's dead and then take a hammer to it. Even selling it for spare parts might be a loss for me so I'm stuck with it.
Click to expand...
Click to collapse
I am sure that they used low quality parts on those last batches of phone, I heard via a friend who lives in Shenzhen that they hired a 3rd party to assemble the final phones... The ones that came with 32gb drives, no nfc or quick charge etc. It sucks because they had so much potential.
Whatever you end up getting. Please do stay in touch, I have enjoyed our conversations and I wish you the best.
tsongming said:
I am sure that they used low quality parts on those last batches of phone, I heard via a friend who lives in Shenzhen that they hired a 3rd party to assemble the final phones... The ones that came with 32gb drives, no nfc or quick charge etc. It sucks because they had so much potential.
Whatever you end up getting. Please do stay in touch, I have enjoyed our conversations and I wish you the best.
Click to expand...
Click to collapse
This puppy is not out yet. I figure it's got one last hurrah before I throw in the towel. I've been shopping around for a phone with similar performance for around the same price but from the current generation of phones and I've not come across anything else. At least not in the same price range. Performance is very important to me and I just can't take a downgrade. I guess I'm stuck with it for a while.
Sent from my LeEco Le Pro3 using XDA Labs
twistyplain said:
This puppy is not out yet. I figure it's got one last hurrah before I throw in the towel. I've been shopping around for a phone with similar performance for around the same price but from the current generation of phones and I've not come across anything else. At least not in the same price range. Performance is very important to me and I just can't take a downgrade. I guess I'm stuck with it for a while.
Sent from my LeEco Le Pro3 using XDA Labs
Click to expand...
Click to collapse
Its good that it's still working for now. Unfortunately you probably only have 4 to 6 weeks before it stops working completely. I was thinking about you situation and made the list below of additional options/good deals.
The Snapdragon 665 has similar performance to the Snapdragon 821 and the Note 8, (the version with the SD665) can be had for under $200 : https://www.amazon.com/Xiaomi-Displ...keywords=Snapdragon+665&qid=1573874157&sr=8-2
If you can spend a just a little more the Mi8's price has dropped to $250, https://www.amazon.com/Xiaomi-6-64G...ef=sr_1_1?keywords=Mi+8&qid=1573874317&sr=8-1 and I can't recommend it enough. It's definitely my most favorite phone that I have owned and I know that you care about the camera a lot. I can promise that the Mi 8 has one hell of a great camera, and stock camera, is absolutely fantastic, especially with video. In fact, I prefer it for video over the latest Pixel 7.XXX Camera and yes it does Astrophotography.
As I mentioned before the A3, is much better than you would ever expect and you can find them for $150.
If budget is a primary concern: It is definitely worth looking at among the best new phones for the money. Plus the bootloader is easily unlocked with no waiting period. if you want a new phone for around $150. I honestly can't think of a better phone, and as I mentioned my daughter has this phone, so I have actually used it, and I am telling you, it's damn good.
Another option is buying a used 128GB Pixel refurbished $120
I have seen them for as low as $75, or you could buy a One Plus 3T
Edit: I just now found this phone and although it has a mediatek processor, its brand new , has Android 9.0 , 4gb ram, 64 gb hd space and it's just a little over $100 UMIDIGI Power This may be the one, if you can deal with processor but there's a lot of people who say that this phone is great, I dont know if you can use roms, but I have heard that it doesn't have bloatware, so it be a smart buy. Edit : The $118 price is a lightning deal, and the price will go backup to $139 by the time you read this. In that case, I would personally avoid it, but I am am a little biased against mediatek for reasons. Mostly heat and poor battery life.
tsongming said:
Its good that it's still working for now. Unfortunately you probably only have 4 to 6 weeks before it stops working completely. I was thinking about you situation and made the list below of additional options/good deals.
The Snapdragon 665 has similar performance to the Snapdragon 821 and the Note 8, (the version with the SD665) can be had for under $200 : https://www.amazon.com/Xiaomi-Displ...keywords=Snapdragon+665&qid=1573874157&sr=8-2
If you can spend a just a little more the Mi8's price has dropped to $250, https://www.amazon.com/Xiaomi-6-64G...ef=sr_1_1?keywords=Mi+8&qid=1573874317&sr=8-1 and I can't recommend it enough. It's definitely my most favorite phone that I have owned and I know that you care about the camera a lot. I can promise that the Mi 8 has one hell of a great camera, and stock camera, is absolutely fantastic, especially with video. In fact, I prefer it for video over the latest Pixel 7.XXX Camera and yes it does Astrophotography.
As I mentioned before the A3, is much better than you would ever expect and you can find them for $150.
If budget is a primary concern: It is definitely worth looking at among the best new phones for the money. Plus the bootloader is easily unlocked with no waiting period. if you want a new phone for around $150. I honestly can't think of a better phone, and as I mentioned my daughter has this phone, so I have actually used it, and I am telling you, it's damn good.
Another option is buying a used 128GB Pixel refurbished $120
I have seen them for as low as $75, or you could buy a One Plus 3T
Edit: I just now found this phone and although it has a mediatek processor, its brand new , has Android 9.0 , 4gb ram, 64 gb hd space and it's just a little over $100 UMIDIGI Power This may be the one, if you can deal with processor but there's a lot of people who say that this phone is great, I dont know if you can use roms, but I have heard that it doesn't have bloatware, so it be a smart buy. Edit : The $118 price is a lightning deal, and the price will go backup to $139 by the time you read this. In that case, I would personally avoid it, but I am am a little biased against mediatek for reasons. Mostly heat and poor battery life.
Click to expand...
Click to collapse
Tony, you're among very few people I know who are invaluable to communities like these. I'm always impressed by how easily you go out of your way to help community members at XDA. Thank you so much for always being helpful even when you don't have to be. If I had the means I would buy you several cases of beer (or whatever non-alcoholic beverage you like) just to say how much I appreciate you. But for now I can just say THANK YOU!! From the bottom of my heart.
Out of all the options you gave me just now and a few days ago, the brand new Mi A3 is the best option by far. Refurbished is a no-go and yes, I hate Mediatek too. Been there, done that, but once you've got a taste of Qualcomm, there's simply no going back. I'm inclined to go for the A3 because of its AMOLED screen, UFS 2.1, decent camera, and, most importantly, it's price-performance ratio. It doesn't beat the A2 in performance but it more than makes up for it in the additional features.
I am going to keep the pro 3 as long as I can to see if prices drop even more (I'm all about the value). It's only my charging port that's gone so I'm taking out the battery and charging it externally for as long as I can. Everything else works normally. I'm also on my last ROM for this phone -- I can't flash another one because I changed to TWRP 3.2.1 which doesn't see my internal storage anymore (encryption).
Sent from my LeEco Le Pro3 using XDA Labs
tylerciggy said:
What ? $30 usd ? I've seen it in $2.5 for 2 boards, well, not original of course.
You just need to check that it has the extra IC, because there are ones that doesn't has it... although I don't remember what was for that IC, but you can easy see it that some boards just are missing a chip.
As for the cable, I'm using some EFFE cables (EFFE is the brand) and they are working wonderfully, I bought 3 for $7 usd, they plug in fine and stay in too, they were recommended to me by a friend and I'm very happy with them. They even stop giving charge to my dead phone because they detect somehow that there is a short, well, at least that is what my usb meter tells me, although I don't know how do they manage to do that, I don't really think they have an IC in them.
Click to expand...
Click to collapse
Sorry I hadn't seen this post. The cheaper boards tagged as "copy" boards don't have working quick charge or ability to connect to pc for mtp file transfer. They're only good for slow charging and sometimes even that is hit or miss. The boards that cost between $25 and $30 are original leeco boards. Probably not brand new but original. They have all features of the original like quick charge, mtp, otg, cdla and everything else the new phone could do. I wouldn't even consider going close to the cheaper "copy" boards.
I had a single 50 cm baseus USB cable that i bought for around $4 and it was of very good quality. It even supported usb PD and it was built like a tank. Just holding it gives you confidence that it's gonna last a while. Even the board getting fried didn't damage the cable but I'm not using it again. The power pin on the usb cable changed from gold to just plain silver so it must have taken some damage. I would buy a new one to be safe.
I'm done repairing this phone for good. It's not worth the expense and there's too much uncertainty involved even after it's fixed. I could fix it and have it die barely a month later. That would be $50 down the drain. I'm not going through that again.
Sent from my LeEco Le Pro3 using XDA Labs
It seems this phone is on its last leg now. Since yesterday the proximity sensor doesn't work. I think it must be all this opening and closing up of the metal shield to remove the battery. Also, the earpiece speaker only works in loudspeaker mode now. It doesn't work in calls. I think I might have an audio related software issue because sound isn't playing even if I play a music or video file. I have flashed another ROM but this behavior remains. Could this require me to flash persist?
Edit: The earpiece and proximity sensor are acting up because of the damaged USB board. Both work well when I use an app that tests hardware features. They are failing to work for phone calls and video playback because the phone is detecting that I have earphones plugged in. I figured this out when I reflashed a new PIE ROM and saw the headphone icon is always displayed on the status bar even without anything connected to the port. I guess the board getting fried messed up with jack detection.
@tsongming Please tell me if this motherboard is le pro3 x722 or le pro3 x720.
https://drive.google.com/file/d/1DD0JQRZe4t4KOmedt0eEThaGEOKBH3AZ/view?usp=sharing
Okay, hello XDA Forums peoples! Ive been lurking here for like a decade. I feel bad for bothering you nice people, but now I'm at my wits end with this phone.
Okay, so, long story short:
Z Fold 3, let it run the One U.I. 4 update, bricked the whole phone, wouldnt come back on. This happens a week away from being out of warranty. So i get samsung to agree to let Asurion/uBreakiFix repair it (I almost always fix my own electronics, I hate Asurion, I've had problems dealing with them before, but its free so whatever). Well they get it working, i asked what they did and they were basically like 'uhhh idk'. I assume it was just an 'unplug the battery and plug it back in' kind of thing.
Anyways fast forward to a couple months ago. Im walking along the creek, i always keep my phone in my backpack for safety. Zipper on my backpack comes open some, phone falls out and directly into the water for about 3-5 seconds. Goes black within 15 minutes. Alright, so it seems like maybe the boys who worked on this didnt seal it back properly. Whatever.
I let it dry for about 4 or 5 days. Comes back on, everything works except the front screen's digitizer(which is cool for me, because the inside screen still works fine) and its reporting too cold to charge, so now once the battery runs out i have a new foldable brick! Yay! I check the battery temperature thats reported in settings and its completely fine. I hit it with a hair dryer for like 5 minutes to try and trip the thermometer, and nothing happens.
I tried some cheap shots in the dark, i replace the USB charging board, i replace the wireless charging coil, both of which have thermistors on other older samsung phones, so i figured it was a decent guess. Still too cold to charge.
So I find a schematic, or not exactly a schematic, but like a boardview, i guess. So at least i know where the thermistors are to check them. Theres about 10 thermistors on the main and sub boards. 5 of which are covered by metal shielding which i am just terrified of trying to remove, mainly because i havent done it before. So i check the other half.
The thermistors used in these phones are like inverse, so they have less resistance for higher temps and more resistance for lower temps. If one of them is dead, it will have like "maximum resistance", right? Which would report the coldest possible temperature, right? So that all makes sense, to me at least.
The 5 i can get to with my meter to check, they seem to work completely fine. From what research ive done they seem to be like 100k resistors when measured at ~70 degrees f, and i can watch the resistance go up and down when its cooled or heated past that temperature. Okay, perfect. That all checks out.
Because the other ones are under some metal shielding, i assume theyre most likely fine because any water would have a harder time getting in there. So i skip to the most expensive option so far: i buy two replacement batteries. The schematics do not include the battery, so i dont know where the thermistors are on my current batteries to check them, if that was the problem.
Well, batteries came yesterday, i pop them in, still too cold to charge. I've already ran the phone dead checking it, so i cant do any further diagnostics with the phone on. And now the most i get is a Yield sign with a thermometer in it when i plug it in.
Okay, so... Idk?? This problem is starting to get over my head. What do y'all think? It seems like my options are becoming more limited and expensive.
I can try and put a big blob of solder on the top of the shielding and pull it off to check the remaining thermistors, which seems to be how people remove those things. I also have have hot air at my disposal, which is always risky with tiny things because too high airspeed might blow components away on the board and then i'll probably cry.
It could just be a connector somewhere on some flex cable? Maybe? I mean like maybe what if one of them is for reporting temperature, and water corrosion is stopping it from sending a signal through???
Im fine with doing whatever, but i just want a charged battery first so i can recover my data before i do anything that drastic. I mean, back in the day they had 4 big pads on a removable battery. You could buy a universal samsung battery charger or rig a USB cable to charge it, but I have literally no idea what to do here. Does anyone know of some specialized battery charger that will connect to these flex cables?? That would be a gigantic help right now. Or if i knew where to get a Z Fold 3 just to pop it open and charge my battery with? Or maybe just sit there for 2 hours holding two wires to the positive and negative pins?!??!?? I dont know. Someone throw ideas at me, please!
Might be worth buying a bench power supply and either injecting voltage through the phone or connecting it to the cells to trickle charge them back up? Im not an expert it these just throwing ideas