Black screen FIRMWARE UPDATE - Google Pixel 2 XL Questions & Answers

I cleaned my phone from water i dried it up after half an hour I kept my pixel 2 xl on charging, it was locked after 5 mins when i looked at my phone..
The screen was black (may be in recovery mode not sure) qon the top its written firmware updating press power button 8 time to reboot your deviceq. Do not unplug your usb blah blah and below was status bar showing 0%
I unplug the cable and device restarted i dint pressed any button
Any one experienced the same or any one knows what it is ?

If you try to power the thing off and back on and it says that it is probably damaged the board. Unless maybe you had flash a ROM of some sort before. But it sounds like you have stock firmware. Even if it did enter recovery or stock recovery you should be able to hard reset it to get it to boot into the ROM

Think that's download mode if you shut the phone off and hold Volume down and plug a data cable in it t will boot in to download mode. like other LG phones. I found it on this phones by mistake once.
Sent from my [device_name] using XDA-Developers Legacy app

666syco said:
Think that's download mode if you shut the phone off and hold Volume down and plug a data cable in it will boot in to download mode. like other LG phones. I found it on this phones by mistake once.
Sent from my [device_name] using XDA-Developers Legacy app
Click to expand...
Click to collapse
Thanks that what it is.

Are there any tools we could use to flash firmware in this mode?

Related

[Q] Brick? (Phone won't stay in download mode)

Hey guys, I'm not sure if my phone is dead. It was running fine this morning, Task & Ktoonsez' AOKP with Ktoonsez kernel. However, I tried to unlock it a little while ago and it wouldn't go on. It boots to the splash screen, both normally and going into recovery, but it doesn't last long enough to go into recovery or boot normally. I try to boot into download mode and it boots, but the phone turns off after a few seconds.
I tried to flash back to stock in Odin, but the phone doesn't stay in download mode long enough for the flash to finish.
I'm not sure what to do. Any help would be appreciated.
Pretty sure if it was bricked it wouldn't boot into download mode at all. It sounds like it is losing power or something. The only thing I can think of is maybe your battery is bad. Download mode can run off of USB power if you remove the battery after booting into it. Maybe plug your phone in and boot into download mode, then take your battery out before it shuts off and see if it stays on.
Lumixz said:
Pretty sure if it was bricked it wouldn't boot into download mode at all. It sounds like it is losing power or something. The only thing I can think of is maybe your battery is bad. Download mode can run off of USB power if you remove the battery after booting into it. Maybe plug your phone in and boot into download mode, then take your battery out before it shuts off and see if it stays on.
Click to expand...
Click to collapse
No dice. It just did the same thing it's been doing. I went into download, popped the battery, it stayed in download for a few seconds, and then powered off.
Could it be a faulty power button? The phone is constantly vibrating by itself and if the power button was messed up it could be causing the phone to leave download mode.
Sun0fNothing said:
No dice. It just did the same thing it's been doing. I went into download, popped the battery, it stayed in download for a few seconds, and then powered off.
Could it be a faulty power button? The phone is constantly vibrating by itself and if the power button was messed up it could be causing the phone to leave download mode.
Click to expand...
Click to collapse
As far as I can tell pressing or holding the power button in download mode will only restart it, but won't shut it off. Also it takes about 10 seconds. I don't think it's your power button.
Lumixz said:
As far as I can tell pressing or holding the power button in download mode will only restart it, but won't shut it off. Also it takes about 10 seconds. I don't think it's your power button.
Click to expand...
Click to collapse
Ah, okay.
In that case, though, I have no clue what's causing the problem here. At this point the only thing I can do is enter download mode for a few seconds, but I can't get it to be enough time to flash a ROM in Odin.
Sun0fNothing said:
Hey guys, I'm not sure if my phone is dead. It was running fine this morning, Task & Ktoonsez' AOKP with Ktoonsez kernel. However, I tried to unlock it a little while ago and it wouldn't go on. It boots to the splash screen, both normally and going into recovery, but it doesn't last long enough to go into recovery or boot normally. I try to boot into download mode and it boots, but the phone turns off after a few seconds.
I tried to flash back to stock in Odin, but the phone doesn't stay in download mode long enough for the flash to finish.
I'm not sure what to do. Any help would be appreciated.
Click to expand...
Click to collapse
Might be a dumb question... Is your battery charged? I'd plug it in for a while off and see if the battery logo comes up and than try putting it in recovery or download.
Sent from my SGH-I747 using xda app-developers app
KorGuy123 said:
Might be a dumb question... Is your battery charged? I'd plug it in for a while off and see if the battery logo comes up and than try putting it in recovery or download.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
I tried that too. It's been plugged in for a while and the same thing happens. It just stays in download mode for a few seconds and then turns off. Also, I tried flashing back to stock in Odin but it failed because the phone turned off before the flash could finish. Now the phone says "Firmware upgrade encountered an issue. Please select Recovery mode in Kies and try again."
So it's basically stuck in download mode cause of a corrupted flash. If I could get the phone to stay in download mode, I could flash it back to stock with Odin, but it's not giving me enough time at this point.
I'm running into the same problem currently, I was wondering if you were able to find a solution. Same ROM same Kernel. I've been using my current version of the ROM since October and haven't flashed anything recently, It just died on me last nigth and now I'm experiencing what you are as well. I was able to turn on the phone somehow last night but it stayed on for couple of mins and turned off again. At the time I had 60% charge.
Thanks
Unfortunately not. Sent my phone back to AT&T and they honored the warranty (despite it being very clear that I was rooted and on custom software).
@fly3rr
Sent from the Dank Device
Sun0fNothing said:
Unfortunately not. Sent my phone back to AT&T and they honored the warranty (despite it being very clear that I was rooted and on custom software).
@fly3rr
Sent from the Dank Device
Click to expand...
Click to collapse
Thanks. I got the phone when it launched so it's been over a year hence I'm well over the one year manufacturer warranty. Doubt they'll honor it for me =/.
Bad news, It's not about software, it's a hardware issue.
I had that issue with a Sprint S3,
The power button switch is stuck pressed all the time, you can try to hit it a little and maybe it pops out but the issue is gonna still there.
If you remove and insert the battery does it vibrates and tries to turn on without pressing the power button?
Damian8a said:
Bad news, It's not about software, it's a hardware issue.
I had that issue with a Sprint S3,
The power button switch is stuck pressed all the time, you can try to hit it a little and maybe it pops out but the issue is gonna still there.
If you remove and insert the battery does it vibrates and tries to turn on without pressing the power button?
Click to expand...
Click to collapse
yup I just realized it was the power button issue. I managed to fix the problem[kind of], i kept trying to get into download mode while connected to AC Adapter with official charging cables. And it stayed in download mode long enough for me to go back to stock ROM. I'm just trying to avoid hitting the power button as much as possible because every time I do something goes crazy and phone turns off.
I'm gonna try and go to AT&T store tomorrow to see if they can do anything about this.
Thanks again for your help. I really appreciate it.
You're welcome. Good luck dude :thumbup:
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I have the same problem. I've tried to install quickly the twrp. But is not time enough
My problem was the battery. After charge a lot, all thing works fine.

[Q] Phone does not boot, red light flashes, is it hard bricked?

Hi,
I woke up to find my note2 stuck on the samsung logo, so i went to the recovery menu and cleared the cache. When I went to restart the phone, it wont start up.
1) Nothing appears on the phone
2) When i press the power button, the red light on top flashes but thats it
3) it doesnt go to recovery mode with the power, vol+
4) it doesnt go to download mode with the power, vol-
5) Battery should be fully charged, when plug into the phone and the wall, nothing happens even when i left it there for half a day.
6) Switched out with friends battery and nothing happens as well.
7) Plug into PC Mac, multiple computers, nothing happens on the phone or computer. Nothing is detected on that usb port.
Anyone know what I can do to try and fix this before I send it to a repair shop?
Thanks
I think u r missing HOME button to press while going recovery or download
jdomadia said:
I think u r missing HOME button to press while going recovery or download
Click to expand...
Click to collapse
Just tried both with home button pressed. Same thing, nothing happens but the red light flashes.
Thanks
Which firmware version was there?
jdomadia said:
Which firmware version was there?
Click to expand...
Click to collapse
Sorry man, I have no idea. I rooted the phone when i first got it and i haven't change/update anything since then. Got the phone around December 2012 in Hong Kong.
lilming263 said:
Sorry man, I have no idea. I rooted the phone when i first got it and i haven't change/update anything since then. Got the phone around December 2012 in Hong Kong.
Click to expand...
Click to collapse
In switched off condition, if it takes charge then it must be go to DOWNLOAD MODE (home+power+vol.down). Then restock through odin or use 'mskip toolkit'
Sent from my GT-N7100 using xda premium
lilming263 said:
Hi,
I woke up to find my note2 stuck on the samsung logo, so i went to the recovery menu and cleared the cache. When I went to restart the phone, it wont start up.
1) Nothing appears on the phone
2) When i press the power button, the red light on top flashes but thats it
3) it doesnt go to recovery mode with the power, vol+
4) it doesnt go to download mode with the power, vol-
5) Battery should be fully charged, when plug into the phone and the wall, nothing happens even when i left it there for half a day.
6) Switched out with friends battery and nothing happens as well.
7) Plug into PC Mac, multiple computers, nothing happens on the phone or computer. Nothing is detected on that usb port.
Anyone know what I can do to try and fix this before I send it to a repair shop?
Thanks
Click to expand...
Click to collapse
few days it happened to my phone also, follow thread,
http://forum.xda-developers.com/showthread.php?t=2351472
Good luck.
nitol said:
In switched off condition, if it takes charge then it must be go to DOWNLOAD MODE (home+power+vol.down). Then restock through odin or use 'mskip toolkit'
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
The phone does not respond while the charger is pluged in and cannot go to Download mode.
apachiee_pk said:
few days it happened to my phone also, follow thread,
http://forum.xda-developers.com/showthread.php?t=2351472
Good luck.
Click to expand...
Click to collapse
Thanks, Looks like I'll have to send it in.

Delete this Thread

Deleted
yawako said:
Warning to everyone please avoid using Freegee Relock feature it can cause semi hardbrick or worst a full hardbrick.
I just had a SEMI NIGHTMARE using Freegee
I installed Freegee, then installed CWM classic installation, everything went fine also made nandroid and efs backup. So I decided to Relock and then "semi hardbrick" happen.
Why Semi Hardbrick because you think you can no longer use the usual Download Mode tricks. (Insert USB, when battery show press the combo key) but that will not happen no matter what you do.
What you see in the screen is a freeze up LG logo with error like secure boot encryption in two lines or something like that.
The hard reset command still work but you cant go any further you will see the error again.
Ok here's the trick and its very tricky its like catching a fly for a Download Mode.
Normally during boot LG logo normally flick twice, then the battery shows if your insert the cable or the animation Logo if loading the system, mine don,t during this trouble time.
What happen that it seems you cant turn off your phone it persist to turn ON with boot encrption error on the screen but to turn OFF you press and hold volume down or up or both and power (this is the key to go Download Mode)
I used the volume down + up and power button
While turning off the device and you think the logo stops showing up release the key then quickly insert usb cable when the LED light turns ON quickly press the Volume UP, DOWN, POWER congrats Download Mode ^_^
I reminder to anyone Please don't use the Freegee Relock function. But if want to witness the near death experience go ahead its safe now ^_^
Click to expand...
Click to collapse
so please confirm you were plugin in the whole time right??
Delete
yawako said:
Yeah I remember I was still plugin (charging using PC) when I use the Relock function of course I have to reboot after that.
If you mean when it gets error you cant plugin your usb because it will trigger the device to turn ON and it persist to turn ON
Click to expand...
Click to collapse
when you are plugged in either by charger or computer, you might not enter recovery or download mode.
turn off your phone by pressing power for extended time.
Delete
yawako said:
You think I dont know what I posted here why not try it for yourself if you have a unit like mine.
If only I took picture of that damned boot error.
Are you sure about download mode? Not using cable?
Click to expand...
Click to collapse
what i have seen here and done myself, sometimes no matter how smart you are or knowledge you have, one always misses the smallest of the things.
yes if you are plugged in you will have a had time to get into download mode or even recovery. sometimes it just wont enter either.
also sometimes phones seems turned off but its not that's where pressing power for extended times comes up. otherwise it will try to boot on plug.
You are far from hard bricked (that's the good news). If the device turns on at all its not hard bricked. If you are getting a security error its most likely because you uninstalled some system apps and didn't put them back before relocking. You might also have not had a backup of your boot.img. Freegee will restore your phone without a boot.img backup if it can't find it, since at least that would put you close enough to stock if you had to take it in, and you can still use download mode.
You can get to download mode because you see the lge logo, download mode is before that logo in the boot sequence.
Sent from my LG-LS970 using xda app-developers app
Shelnutt2 said:
You are far from hard bricked (that's the good news). If the device turns on at all its not hard bricked. If you are getting a security error its most likely because you uninstalled some system apps and didn't put them back before relocking. You might also have not had a backup of your boot.img. Freegee will restore your phone without a boot.img backup if it can't find it, since at least that would put you close enough to stock if you had to take it in, and you can still use download mode.
You can get to download mode because you see the lge logo, download mode is before that logo in the boot sequence.
Sent from my LG-LS970 using xda app-developers app
Click to expand...
Click to collapse
Good luck with your FreeGee

BootLoop post Viper4Android module on Magisk with Lineage 15/Oreo

Lineage /Oreo was installed thru TWRP 3.xxx, running fine but unhappy , no Viper4Android , so I installed it as a module on Magisk,
after installing the driver, was ask to reboot as directed, but went into bootloop , stuck on a boot loop " Set Warranty Bit : kernel " top left corner and Samsung Galaxy Note 3 on screen ; I tried Vol Up +Home+ power combo and all other combi I could think but no luck , Odin wont recognize my phone, tried Samsung 300k tool with no luck, I fell like a newbie after using so many ROMs on all of my devices, I google how to get back to download mode but no luck, I need help to make my Samsung note 3 work again, PLEASE. THANKS.
Hi,
I have same phone but I'm running Resurrection Remix 6 which is based on LineageOS 15.1 and I'm able to use the Viper module through Magisk 16.3 without any problems. No bootloops, no nothing.
I never would have guessed that a sound mod could brick the device to the point that the buttons no longer function. Hopefully other users will chime in and help you fix it.
Best of luck.
EDIT: Try taking the battery out to force it to shut down and then try the recovery/download mode technique again. Sometimes, it'll end up in a bootloop and the buttons will be become unresponsive. I know it may seem a bit strange, but that scenario is entirely possible given the age of the device.
Sent from my SM-N900T using Tapatalk
AndroidHacker99 said:
Hi,
I have same phone but I'm running Resurrection Remix 6 which is based on LineageOS 15.1 and I'm able to use the Viper module through Magisk 16.3 without any problems. No bootloops, no nothing.
I never would have guessed that a sound mod could brick the device to the point that the buttons no longer function. Hopefully other users will chime in and help you fix it.
Best of luck.
EDIT: Try taking the battery out to force it to shut down and then try the recovery/download mode technique again. Sometimes, it'll end up in a bootloop and the buttons will be become unresponsive. I know it may seem a bit strange, but that scenario is entirely possible given the age of the device.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
I did tried RR 6, but I had trouble with 1.) power Button menu option, screenshot/screen record , 2.) Viper4Android , a must have on all my Android devices, and last 3.) latest Android version , if I dont get the first 2 obsession , that's when I switched to a different ROM (LOL), but seriously , all I need is to get HELP to get back to download mode again, Vol Up + Home + Power, did that for 2 days approaching the 3rd day (LOL). HEEEELLLLLPPPPPPP.
Isn't download mode volume down + home + power?
Aykee said:
I did tried RR 6, but I had trouble with 1.) power Button menu option, screenshot/screen record , 2.) Viper4Android , a must have on all my Android devices, and last 3.) latest Android version , if I dont get the first 2 obsession , that's when I switched to a different ROM (LOL), but seriously , all I need is to get HELP to get back to download mode again, Vol Up + Home + Power, did that for 2 days approaching the 3rd day (LOL). HEEEELLLLLPPPPPPP.
Click to expand...
Click to collapse
You need to take the battery out to force it out of the bootloop then push volume DOWN, home & power.
Sent from my SM-N900T using Tapatalk
audit13 said:
Isn't download mode volume down + home + power?
Click to expand...
Click to collapse
Sorry, I mean Vol down but no luck.
You may have to try a USB jig to get into download mode.
https://forum.xda-developers.com/galaxy-s3/general/ref-borrow-usb-jig-near-updated-t1891197
Aykee said:
Sorry, I mean Vol down but no luck.
Click to expand...
Click to collapse
Can you also not boot into TWRP by holding Home+PWR+Volume up? If so you can boot to Download Mode from there.
Sent from my toaster using Magic
audit13 said:
You may have to try a USB jig to get into download mode.
https://forum.xda-developers.com/galaxy-s3/general/ref-borrow-usb-jig-near-updated-t1891197
Click to expand...
Click to collapse
Sounds like a good idea, ordering on amazon..thanks
ludeawakening said:
Can you also not boot into TWRP by holding Home+PWR+Volume up? If so you can boot to Download Mode from there.
Sent from my toaster using Magic
Click to expand...
Click to collapse
I did all button combination, cant get into download nor recovery mode , am not sure if buttons are wack but it feel responsive and clicky but thanks anyway am going for the USB jig, I never had one.
audit13 said:
You may have to try a USB jig to get into download mode.
https://forum.xda-developers.com/galaxy-s3/general/ref-borrow-usb-jig-near-updated-t1891197
Click to expand...
Click to collapse
I got the USB jig but nothing happen after plugging in, any other idea please?
Removed the battery, inserted the jig, and then inserted a charged battery?
audit13 said:
Removed the battery, inserted the jig, and then inserted a charged battery?
Click to expand...
Click to collapse
The jig that I bought didnt do anything so I make my own, I can go to download mode now, installed this ROM/firmware N900TUVUCNB4_N900TTMBCNB4_N900TUVUCNB4_HOME.tar.md5 succesfully but wont go pass beyond the tmobile logo, tried a few more firmware and lately this N900TUVUFOL1 and also , am stuck to Tmobile logo, anybody knows which firmware would likely bring my note 3 back to life, thanks in advance.:
Try this:
Uncheck everything in Odin except f reset time. Flash the latest ROM again. When you see the word "reset" in the status WIndow, remove the USB cable from the phone, remove the battery, replace battery, boot into recovery mode using buttons, factory wipe, and reboot.
audit13 said:
Try this:
Uncheck everything in Odin except f reset time. Flash the latest ROM again. When you see the word "reset" in the status WIndow, remove the USB cable from the phone, remove the battery, replace battery, boot into recovery mode using buttons, factory wipe, and reboot.
Click to expand...
Click to collapse
After "reset" status, I did remove cable, remove batt and boot up to recovery, the blue light lit up as if its going to recovery mode , android logo showed up but phone boot up to normal but not pass beyond tmobile logo, so I did CF-root via odin , but still not booting to recovery.
Try flashing the entire ROM in AP.
audit13 said:
Try flashing the entire ROM in AP.
Click to expand...
Click to collapse
Thanks Audit13,
I manage to restore my Note 3 to TMobile Android 5 using repair firmware , it looks like I wipe out the partition ,My phone runs like new, am just wondering why I cant go to Download mode with button combinations of Volume -/Home/power , tried to install twrp via Odin, it says PASS but Vol +/Home/Power wont lead me to bootloader, did tried CWM , it will boot up but before I could start using it, it will reboot to normal and I could not go back to bootloader with button combo Vol+/Home/Power........HELP...
Download mode is volume down+home+power.
To flash TWRP with Odin, try this:
Open Odin and only check f reset time. Flash TWRP. When you see the word reset in the Odin status window, remove the USB cable from the phone, remove the battery, replace battery, press home + volume up + power.
N900TUVUFOB6_N900TTMBFOB6_TMB and N900 PIT - are the files am using after screwing up my partition( I dont know how I did that ), this Note 3 is running like a hot knife on a butter BUT the only bug I notice is Volume Up + Home + Power ( recovery) NOR Volume Down + Home + Power (download ) does not work, I can only go to download mode using a USB JIG and no other way. I can flash TWRP via Odin with Auto-reboot not ticked , so I could remove cable, battery , hoping to get me to recovery mode but I couldnt. Did I miss a step?I need help.

Can't access download mode - bricked phone?

I'm pretty sure I permabricked this phone by:
* reflashing the stock system image
* flashboot --set-active=_b
* flashboot flash boot twrp-3.2.1-0-cheryl.img
Now I can't boot or access download mode - I was able to before by holding the volume down button when powering on.
Each of these steps I'd done many times before trying to getting a bootable LineageOS install. I was actually pretty close - ran into the enter decryption key problem, used twrp to "format data" to try to get a fresh decrypted data partition, but was now stuck at the endless os boot animation.
I had read the suggestion to reflash the stock image and try again when having this kind of issue. It seemed safe, I had done it before, but I think that this time for some reason, it left me in a bricked state.
Any suggestions for getting out? I'm basically stuck on the first black and white Razer logo screen that says "Powered by android". The phone isn't detectable as a USB device on any of my computers anymore and nothing I do seems to be able to get it into download mode.
kjdjfhdhg said:
I'm pretty sure I permabricked this phone by:
* reflashing the stock system image
* flashboot --set-active=_b
* flashboot flash boot twrp-3.2.1-0-cheryl.img
Now I can't boot or access download mode - I was able to before by holding the volume down button when powering on.
Each of these steps I'd done many times before trying to getting a bootable LineageOS install. I was actually pretty close - ran into the enter decryption key problem, used twrp to "format data" to try to get a fresh decrypted data partition, but was now stuck at the endless os boot animation.
I had read the suggestion to reflash the stock image and try again when having this kind of issue. It seemed safe, I had done it before, but I think that this time for some reason, it left me in a bricked state.
Any suggestions for getting out? I'm basically stuck on the first black and white Razer logo screen that says "Powered by android". The phone isn't detectable as a USB device on any of my computers anymore and nothing I do seems to be able to get it into download mode.
Click to expand...
Click to collapse
I have done that a few times. Each time I powered on the phone and left it at the black and white razer logo screen until the battery drained. Then I plugged the phone into the wall charger for a few hours to make sure it was full again. Then I plugged the phone into my pc and do the volume down and power thing to get into download mode. I don't know why draining the battery and charging it helped me out, but I have had to do it a few times because I got stuck on that razer logo screen just like you are now.
tabletalker7 said:
I have done that a few times. Each time I powered on the phone and left it at the black and white razer logo screen until the battery drained. Then I plugged the phone into the wall charger for a few hours to make sure it was full again. Then I plugged the phone into my pc and do the volume down and power thing to get into download mode. I don't know why draining the battery and charging it helped me out, but I have had to do it a few times because I got stuck on that razer logo screen just like you are now.
Click to expand...
Click to collapse
Thank you so much for the reply, I'm going to try that right now!
kjdjfhdhg said:
Thank you so much for the reply, I'm going to try that right now!
Click to expand...
Click to collapse
I have always had to press 3 buttons not 2 to get into download. Vol down, power, and home (s7) or Bixby (s9). If I did not get them all right, I got your results.
Sent from my [device_name] using XDA-Developers Legacy app
No luck with waiting for the battery to die or the 3 button salute - pretty sure I'm hosed here. Let my experience be a lesson to others, Razer phones are quite easy to brick!
gaww said:
I have always had to press 3 buttons not 2 to get into download. Vol down, power, and home (s7) or Bixby (s9). If I did not get them all right, I got your results.
Click to expand...
Click to collapse
Razer phone has no physical home button. Only possible way is plugged usb from a non charging source like a computer or another phone and Vol down + power or plug in usb from a computer while volume down is held down.
---------- Post added at 11:01 PM ---------- Previous post was at 10:58 PM ----------
kjdjfhdhg said:
No luck with waiting for the battery to die or the 3 button salute - pretty sure I'm hosed here. Let my experience be a lesson to others, Razer phones are quite easy to brick!
Click to expand...
Click to collapse
So have you tried the following?
Hold volume up and power for the phone to hard shutdown and as soon as the screen goes black, let go of all buttons then plug a usb c to a cpmputer first then before pluging anything to the phone, hold volume down and as you are holding volume down, plug in the cable to the phone?
iliais347 said:
Razer phone has no physical home button. Only possible way is plugged usb from a non charging source like a computer or another phone and Vol down + power or plug in usb from a computer while volume down is held down.
---------- Post added at 11:01 PM ---------- Previous post was at 10:58 PM ----------
So have you tried the following?
Hold volume up and power for the phone to hard shutdown and as soon as the screen goes black, let go of all buttons then plug a usb c to a cpmputer first then before pluging anything to the phone, hold volume down and as you are holding volume down, plug in the cable to the phone?
Click to expand...
Click to collapse
This thread popped up under "participated" somehow - did not note it wasn't Samsung- lol.
Sent from my [device_name] using XDA-Developers Legacy app
Hold power and volume up for a minute or more till it fully powers down. I don't remember having another device that took as long as this one to hard reset.
kjdjfhdhg said:
No luck with waiting for the battery to die or the 3 button salute - pretty sure I'm hosed here. Let my experience be a lesson to others, Razer phones are quite easy to brick!
Click to expand...
Click to collapse
any update on this? i'm currently in the same position!
manor7777 said:
any update on this? i'm currently in the same position!
Click to expand...
Click to collapse
The trigger to enter fastboot seems to be holding the "vol down" key AND the usb cable attached to the pc. You should connect the cable first and then do the hard reboot+release keys+hold vol down
waiflih said:
The trigger to enter fastboot seems to be holding the "vol down" key AND the usb cable attached to the pc. You should connect the cable first and then do the hard reboot+release keys+hold vol down
Click to expand...
Click to collapse
No difference. Always worked for me with phone powered off and holding the vol down and then plugging it in, tried that too and didn't work for me.
Hi i have found company (if you google "arykstore") that deals with hardbrick issues. They just started unbrick project on razer phone after my request for help. If they rise money to obtain working razer device they will extract and provide essential filles to resurrect any hardbricked razer phone.

Categories

Resources