Dear All !! Dear Pof!
I am trying to unlock hTC S620 ,but with no luck!!
when i connect the phone with Active Sync with the softwear and press AUTO_Unlock_v3a it showing me direct the message :
SoftSPL error
Erorr
Insufficient trustlevel.
You need to application unlock your device (or singn executable with privileged cert)
even i did try to past the file SSPL in phone and open it ,it gona say to me the same erorr !!
Please what is this problem is ?
and another think :how can i make hardwear Reset to this model hTC S620? ther is no hole place to press For reset ,could u show me please how to do it .
i am very sad becouse i spend over 5 hours trying to unlock this funny phone!!!
please help!!
Thanks.
Hi, I have a problem with my defy and I really short to deal with that. First my defy stopped on red M logo and done proceed to system start. So I go to service menu, set clear cache- cache were cleared for 30mins so I take out batery, then I set - format/factory reset. same problem, it goes without end so after batery goes off, I make McGiver style for bring pnone to life and go to boot loader, run firmware flash over RSD lite and wait......after that RSD give me this message - Phone [0000] Error verifiing code group 33 Checksums. File:0x8BAC,Phone:0x4805 . RSD do nothing, on phone were instaling. after our when I suppose this is and I take out batery from phone and try run it. Every time start boot loader with message :
Code Corrupt
Battery OK
OK to Program
Conect USB
Data Cable
I cant launch android recovery, and If i flashed firmware again a have the same and. Can you please somebody help me with that??
Thanks,
ps. sorry for my english I think is not perfect
new thing, new error mesage from RSD. he pass Checksums errors, than give me message - restarting device ( that is not happend, device were still on), afted while there is new message : Failed flashing proces. Failed plashing proces. phone [0000] Error geting subscriber unit checksum. Device API error: 0xe003003F Command : (RQRCS 0xe403203f); phone conected
result FAIL
I am really desperate.. anyone have experience with this??
Thanks for any advice.
NoDi
As I see probably nobody had this issue like I had. Tomorrow I try bring phone to seller (Vodafone), and than I have to pray for reflashing it from them. Anywhere I will post result from them after I get some, If somebody have the same problem in future like I had.
NoDi
Difrent SFB
try usuing difrent sfb f.
have similar problem at some time...
just try using another sfb and do factory reset each time
yea.. some sbf have higher or lower on img version which might prevent your phone from fully flashed.
I tried various different FW from here. Everytime the same results. Today I was bring phone to Vodafone, I wonder on verdict
you said you tried all firmware versions, can you try diffrent RSD Lite version, may be RSD lite having problem. I am using " RSD Lite 4.9.msi ".
so phone is back. In report from service were Changed bad SWAP module. In used parts were 1pcs of RF board. Anyway I brought phone back to Vodafone because he cant sign in other than 3G network, and many places in our country are sill only 2G.
The pad is stuck at Download mode/logo ( turn it on , it goes to download mode, plugin computer without Vol up , also goes into download mod )
I already tried the lg flash tool 2014 tool with kdz file and it got server disconnection error after extraction.
With the offical LG Mobile tool (it can detect correct model ) which downloads 1.4GB, it fails after finish dowloading/extraction
The only method I have not tried is the TOT file which I cant find it for free . And I am not sure if I bought the file , it would fix .
So, does anyone get any idea about what happens ? bad / dead flash rom ? bad usb port ? etc. ?
Is there a way to force flash with diff TOT file like with V510 ?
TIA
The "Server disconnection" error dialog and other error dialogs are common and normal. 99.9% of the time if you totally ignore any error dialog, don't press any buttons in the dialogs, just at the most drag them out of your way and ignore them, then on the VK810, within 20 minutes I find that my VK810 is successfully flashed.
Hi everyone ,
(first sorry for my bad english)
i got a g8 rio-l01 with a few problem ( no imei , no sn , no wifi and bt mac adresse) all this problem was solved using the hcu tool
but the biggest problem is the phone boot in a factory mode ,i can see this in the projectmenu>veneer informaton>other info>run mode: factory
so in this mode :
1-i have no shortcut panel and notification panel when i slide from up to down nothing come
2-no signial or network conection
3-in the first home page in the phone i have MMIs app/software upgrade/MMI/projectmenu/MMIa,
in the second one i have runningtest3
in the last one basic android app
4-i can't use keyboard
so i have trayed i think all huawei g8 firmware and nothing change
trayed with DC phoenix methode (the two methode) and same problem
trayed with the original soft (RIO-L01_M105_Board Software_general_Android 5.1_EMUI 3.1_05021TJY) and no change
trayed with l02 ,l03 ,tl00 ,slim6 and cm13 and the problem persist
bootloader and frp are unlocked ,sim too with hcu and phone rooted
if i remove appfac from user data and reboot the keyboard Appears and other app Appears but the phone stay in factory mode with no upper pannel and no network signial
i can use wifi and bt
in fastboot getvar pruduct give msm8916 (it's normal??? the phone is an msm8936)
i think there is a currupted or a missing file or partition
i have all factory flash file
bootloaderimage: huawei_msimage.mbn, MPRG8936.mbn (i don't know how tu use this two files)
fastbootimage: boot.img, ,cache.img ,cust.img ,emmc_appsboot.mbn ,erecovery.img ,frp.img ,fs_image.tar.gz.mbn.img ,gpt_both0.bin ,hyp.mbn ,log.img ,misc.mbn ,modem_st1.mbn ,modem_st2.mbn ,NON-HLOS.bin ,oeminfo.mbn , persist.img ,recovery.img ,rpm.mbn ,sbl1.mbn ,system.img ,tz.mbn,userdata.img ( and all crc file )
any idea are welcome
thank you
Hi again
So after many test ( and break and unbreak the soft many times) by editing prop and conf files, i noticed that the ro.runmode is the command controling the boot mode.
But i don't know were is this command and if it's possibol:
- To force ro.runmode=normal?
- Or any solution to by pass runningtest3 app or to fake the result?
Thank you (any help are welcome i don't worry about bteaking the phone)
Finally the phone is fully dead ?
After many flash factory, stock and custom i decided to find the way to enter to hs-usb 9008 mode and i find,by flashing the phone with cherry honor 4 rom. And the phone rebooted in 9008 mode, than flashed the ddr and the msm8936 file with zte tool. The msm will not finish and the phone reboot in fastboot (with red, green,blue screen) than reflashed factory rom with dc unlocker the phone rebooted normal but with the same problem that i have in the first.
Second try, flashed with cherry, entred 9008 mode,reflashed with zte tool (by error used a bad msm8936 file from lenovo)
And the phone stop working not detected and black screen
Third try, desassemled the phone, removed battery find test point after many risky test,the phone boot again in 9008 mode.
Reflashed with zte tool, enter red green blue fastboot, and decided to reflash all the factory with fastboot flashall méthode to unbrick an msm8916. Fastboot finish with many failed.
The phone rebooted but black screen and blinking led with continus (red,blue, green), not detected in pc, trayed with test point and nothing
I think it's fully dead now
Sorry for all this long text but just to share expérience
Thank you
And no it's not dead ðŸ˜, find the way to boot it again in 9008 mode with shorting two test point
Here we go for other test
السلام عليكم
hello friend
have you tried to flash the OEMINFO partition (if not be careful because the unlocked code of the bootloader will be changed and you need to read the new one with hcu client)
if you dont know how to do, tell me
sorry for bad english I'm not english man
xzanium said:
السلام عليكم
hello friend
have you tried to flash the OEMINFO partition (if not be careful because the unlocked code of the bootloader will be changed and you need to read the new one with hcu client)
if you dont know how to do, tell me
sorry for bad english I'm not english man
Click to expand...
Click to collapse
allrady solved my problem with an oeminfo but it work only single sim i need an other oeminfo with dual sim
thank you
How To Get Oeminfo
makabress said:
allrady solved my problem with an oeminfo but it work only single sim i need an other oeminfo with dual sim
thank you
Click to expand...
Click to collapse
makabress Please clear here how to get oem info and write it.. i m alredy face same problem..
hellowbd said:
makabress Please clear here how to get oem info and write it.. i m alredy face same problem..
Click to expand...
Click to collapse
Hi , i found the oeminfo searching in google. I will try to find it again
hello
i a have the same prolem but i cant find "the service rom" too, my phone is stuck in mode 9008 i tried to do the rom by myself but witouth any succes.... i read in a post that i cant try to put the "Huawei_Honor_Cherry_L04_V100R001C900B150_India_4.4.4_EMUI_3.0_05021SLQ" who has the same structure but cannot flash phone said "bootloaderimage" fail
please anyone can help me? i am 2 months witout phone... sorry about my bad english im a spanish guy
rio-l01 test point
hi, please i can't found rio-l01 test point can you help me
rmili25 said:
hi, please i can't found rio-l01 test point can you help me
Click to expand...
Click to collapse
test point are in the left/right side of the display connector, you can use a small wire to short it
JoseBankai said:
test point are in the left/right side of the display connector, you can use a small wire to short it
Click to expand...
Click to collapse
thank you brother
please i have the same problem ( rio-l01 no service no call ) can you help me please by oeminfo file or other things
excuse me i'am bad in english
still having the same problem, no solution, try to resoldering emmc, processor, voltage are ok, everything works in other board, so the problem is still the **** mode 9800 and the vanished "service rom" (not trully vanished but every service that i call to fix this ask me for a lot of money just to fix 1 phone... not worth it..) hope somebody can explain this at least, and why is happening, maybe one day can recovery my data on thtat phone....
good night I have a xaomi my max 3 working well a day but the blotter and when the regression solo is in the back of my ni in the ingratiate recovery, but I can enter the quick start mode and the PC recognize when I try to go for it the error: falló (remote: blurry is not allowed in lockout state) Probl edl mode and one error (one edl mode; can not receive the package hello) and the other type, as you need to have a cuenta de Authorized bootload My phone is blocked, if you decide, at once in the way you want and with an authorized box My harías are for you to help? Please, thanks from Brazil, sorry for the bad language