Related
As a general FYI, if you think you need to repartition your phone it is also possible that your phone has experienced:
a) A hardware issue, possibly partial or total emmc failure.
b) A mismatch between bootloader (sboot.bin) and trustzone (tz.img) versions. See this post or my MK6 stock thread for some possible options to fix this.
As a step of last resort to recreate the partition table on your phone, a pit file may be what you need. This can be done in either Odin or Heimdall.
Warning - repartitioning your phone may erase all data and might cause other unintended consequences. You assume all risk.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------
To use a pit file in Odin, this is typically done as part of a flashing a stock rom package, like the LJ2 or MA4 package for the i317 (or similar package for the i317m). You specify the pit file in the PIT section, make sure the repartition box is checked, and then add the rom package in the PDA section like usual.
If you are running an official 4.3 or later bootloader you will not be able to successfully flash a stock firmware package that contains earlier bootloaders - Odin will hang and you will need to find a different stock package to flash that does not contain a bootloader. (i.e. If you took the the i317 4.3 OTA and are running the MK6 bootloader or a later bootloader, you'll want to avoid UCAMA4)
The attached zip includes pit files for both the i317 and the i317m. The partition mapping is the same for both (see the included analysis files), but the pit files have unique security signatures which are accepted only by the bootloader of the specific model phone for which they are intended. I've tested the file for the i317 and can confirm that it works as intended. The file for the i317m was pulled the same way by an XDA member (thanks @plemen !) with an i317m and I've confirmed it is formatted correctly. It has now been confirmed as working.
If you want to learn a bit more about pit files, check out this thread by Adam Outler:
http://forum.xda-developers.com/showthread.php?t=2540480
Very interested in this, as I need the pit file for my I317. Question about the bootloader, though.... I've never taken an OTA, just flashing CM and OmniROM nightlies (was on 4.4.2 when my phone committed suicide). Should I be safe to use this pit file? And what factory firmware would you recommend to go with it?
pit files should be back in a day or two (I'll be testing over the weekend).
Depending on what happened to your phone it's still highly probable that your pit (partition) data is fine. There's a way to confirm this using Heimdall - when time permits I'll add instructions to post #2. That's a safer first step than attempting a repartition.
As for bootloader and firmware - if you've never taken an OTA, and you're not on a 4.3 bootloader your best bet for stock firmware is UCAMA4. It's a more complete and somewhat newer package than the other option (UCALJ2). You can get this from sammobile, or a mirror copy I have linked in post #2 here:
http://forum.xda-developers.com/showthread.php?t=2589891
that post also has information on a couple apps you can load that will allow you to check which bootloader you have loaded once your phone is operational.
Thanks for doing this! Did you have any luck over the weekend? Looking to re-partition as I'm unable to mount.
anine said:
Thanks for doing this! Did you have any luck over the weekend? Looking to re-partition as I'm unable to mount.
Click to expand...
Click to collapse
I expected a test phone on Saturday that didn't arrive until Tuesday thanks to the USPS getting the day off on Monday. Once I confirm the files work as intended I will repost them.
As for the issue you are having - what partition isn't mounting? Can you provide more detail?
Zen Arcade said:
I expected a test phone on Saturday that didn't arrive until Tuesday thanks to the USPS getting the day off on Monday. Once I confirm the files work as intended I will repost them.
As for the issue you are having - what partition isn't mounting? Can you provide more detail?
Click to expand...
Click to collapse
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Help
anine said:
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Click to expand...
Click to collapse
I desperately need this PIT file as well.. not on 4.3 however..I can get to download mode and into recovery but it spits a bunch of errors about unable to mount /cache etc...
anine said:
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Click to expand...
Click to collapse
The symptoms you describe are similar to those I've seen on the Q&A forum recently. I don't want to be the bearer of bad tidings, but I suspect you have a partial emmc (hardware) failure.
My time during the week is limited so I expect to have testing done this weekend.
terpencar said:
I desperately need this PIT file as well.. not on 4.3 however..I can get to download mode and into recovery but it spits a bunch of errors about unable to mount /cache etc...
Click to expand...
Click to collapse
I had similar issue, and was able to resolve it by following this thread. YOu need to restore factory original by following this thread from XDA.
Please don't forget to Thank
The files provided are only for phone I317 and not I317M
http://www.androidfilehost.com/?fid=23060877490003986
Instructions:
1. Download "back to stock" zip folder I uploaded. It contains all the files needed. No need to search around.
2. Unzip the file and extract the folder to your desktop.
3. Open folder and install Samsung drivers if not already done so.
4. Now make sure you have root and custom recovery on the phone. Turn the phone off. Hold volume up, home and power button at the same time.Wait till u see custom recovery screen and then let go off all the buttons.
5. Once in recovery... delete data, system, cache, dev cache like you want to flash a new rom. Turn the phone off by pulling the battery or see option for power off device under custom recovery.
6. Once the phone is completely off lets get into download mode. Hold volume down, home and power button until you see the screen with an option to press volume up to get into download. Press volume up to enter download mode when asked.
7. Now open odin3.07 I provided in the folder u downloaded. Once open connect your phone via usb. Windows should install device drivers. Once thats done, you should see com## on the Odin software.
8. On odin software you should see button called PDA. Click on it and browse to the file called KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user _low_ship.tar. in the folder provided by me. select it and hit ok. Odin will process the file. It will take max 2 to 3 min.
9. Before you click start on Odin make sure auto reboot and F. reset time is checked only. Everything else unchecked. Click start button. Odin will start flashing the factory firmware. It will take time.
10. Once Odin is done flashing. phone will reboot. Now you can disconnect the usb cable. When phone is fully rebooted, skip all the prompt and get to home screen.
11. Turn the phone off again and get into download mode. Connect usb cable to computer with Odin open. Click Pda and select file called CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.tar. Let Odin process it and then click start. Once flashing the root file is done. Phone should reboot to home screen. Now you have root. The reason we need root is to get rid of counter # in download more. It should say zero.
12. Connect your phone to computer while on the home screen. Open phone internal storage and go to download folder and copy Triangle away.apk into it.
13. Go into settings and security and check unknown sources.
14. Go to apps and open application "my file". Go to download folder and select triangle away application to install. install it. Open application application and scroll down and select reset counter option. Make sure your are connected to wifi. Confirm you phone is I317 and triangle away will download the file. Your phone should reboot into some type of reset counter recovery screen. follow the instruction on the screen to reset the counter. After that phone should reboot.
15. Once rebooted uninstall triangle away apk. Now open super user application and scrool down and click fully unroot. When done go into stock recovery and clear data and cache. reboot phone. All done. Your counter is set to zero. Your phone should read normal under settings.
You can update your phone under settings from att servers.
Enjoy.
Thanks to chainfire for his triangle away app and root for our device.
rob_z11 said:
I had similar issue, and was able to resolve it by following this thread. YOu need to restore factory original by following this thread from XDA.
Please don't forget to Thank
The files provided are only for phone I317 and not I317M
Instructions:
1. Download "back to stock" zip folder I uploaded. It contains all the files needed. No need to search around.
2. Unzip the file and extract the folder to your desktop.
3. Open folder and install Samsung drivers if not already done so.
4. Now make sure you have root and custom recovery on the phone. Turn the phone off. Hold volume up, home and power button at the same time.Wait till u see custom recovery screen and then let go off all the buttons.
5. Once in recovery... delete data, system, cache, dev cache like you want to flash a new rom. Turn the phone off by pulling the battery or see option for power off device under custom recovery.
6. Once the phone is completely off lets get into download mode. Hold volume down, home and power button until you see the screen with an option to press volume up to get into download. Press volume up to enter download mode when asked.
7. Now open odin3.07 I provided in the folder u downloaded. Once open connect your phone via usb. Windows should install device drivers. Once thats done, you should see com## on the Odin software.
8. On odin software you should see button called PDA. Click on it and browse to the file called KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user _low_ship.tar. in the folder provided by me. select it and hit ok. Odin will process the file. It will take max 2 to 3 min.
9. Before you click start on Odin make sure auto reboot and F. reset time is checked only. Everything else unchecked. Click start button. Odin will start flashing the factory firmware. It will take time.
10. Once Odin is done flashing. phone will reboot. Now you can disconnect the usb cable. When phone is fully rebooted, skip all the prompt and get to home screen.
11. Turn the phone off again and get into download mode. Connect usb cable to computer with Odin open. Click Pda and select file called CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.tar. Let Odin process it and then click start. Once flashing the root file is done. Phone should reboot to home screen. Now you have root. The reason we need root is to get rid of counter # in download more. It should say zero.
12. Connect your phone to computer while on the home screen. Open phone internal storage and go to download folder and copy Triangle away.apk into it.
13. Go into settings and security and check unknown sources.
14. Go to apps and open application "my file". Go to download folder and select triangle away application to install. install it. Open application application and scroll down and select reset counter option. Make sure your are connected to wifi. Confirm you phone is I317 and triangle away will download the file. Your phone should reboot into some type of reset counter recovery screen. follow the instruction on the screen to reset the counter. After that phone should reboot.
15. Once rebooted uninstall triangle away apk. Now open super user application and scrool down and click fully unroot. When done go into stock recovery and clear data and cache. reboot phone. All done. Your counter is set to zero. Your phone should read normal under settings.
You can update your phone under settings from att servers.
Enjoy.
Thanks to chainfire for his triangle away app and root for our device.
Click to expand...
Click to collapse
Thanks.. It just hangs at system.img in odin
Nice job Zen
Sent from my SGH-I317 using XDA Premium 4 mobile app
Pit files are back up and attached to the OP. The i317 pit file is tested and confirmed working.
The i317m file is identical, except for the security signature. I'm currently looking for someone with a healthy i317m willing to test flash the i317m pit file to confirm it works. (I would do this myself, but I don't have an i317m).
Unfortunately it did not work for me. emmc failure suspected. Strange thing is that in ODIN I can still "Successfully" install a ROM.. and even the PIT file succeeded. I still got a logo screen for several minutes.
Fortunately for me, I have an additional mainboard from a otherwise damaged note 2. I'll be swapping that out.
Thank you anyway. Hope your file helps others!
My phone was not booting and stopped at Samsung logo. After the pit file and stock rom, my phone is live again. I am still having issue with storage but at least I have good starting point.
thanks
Works fine on i317m
anine said:
Unfortunately it did not work for me. emmc failure suspected. Strange thing is that in ODIN I can still "Successfully" install a ROM.. and even the PIT file succeeded. I still got a logo screen for several minutes.
Fortunately for me, I have an additional mainboard from a otherwise damaged note 2. I'll be swapping that out.
Thank you anyway. Hope your file helps others!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2626593
qkster said:
http://forum.xda-developers.com/showthread.php?t=2626593
Click to expand...
Click to collapse
See posts #9 and #13 on the thread above for the specific potential solution to try.
Corrupt pit file it says. for note 2 att help
I have a Att note 2 i flash the mj9 firmware using mobile odin first. Then i formatted storage, data, system, and cache. And now its says i have NO ios Installed with is true but when i try flashing another rom in TWRP it fails iv'e try stock ATT, Jedi Rom, MeanBean Rom. now i tryed to flash stock firmware through J Odin but it always say corrupt pit file...Someone Please Help MEE
kumar_420 said:
I have a Att note 2 i flash the mj9 firmware using mobile odin first. Then i formatted storage, data, system, and cache. And now its says i have NO ios Installed with is true but when i try flashing another rom in TWRP it fails iv'e try stock ATT, Jedi Rom, MeanBean Rom. now i tryed to flash stock firmware through J Odin but it always say corrupt pit file...Someone Please Help MEE
Click to expand...
Click to collapse
Err mj9 is verizon haha
Sent from my lightning fast Note II running MeanBean 2.0 SuperCharged
I am creating this guide to convert convert the G930VL to G930V since i cant find a guide for android 7.0 and The G930VL firmware is no ware to be found. I have been a long time member and have flashed many roms on phones and normaly dont find a need to post but since i could not find much on the internet i decided to make a step by step guide.
I take no credit for creating any of the tools used in this guide as i was not the creator. I have only figured out the way to get the G930V firmware on to the phone.
I am not responsible for any bricked devices
You must have usb drivers installed
Tools:
SamFirm V0.3.6 (as of writing) https://forum.xda-developers.com/galaxy-tab-s/general/tool-samfirm-samsung-firmware-t2988647
Odin PrinceComsy https://forum.xda-developers.com/verizon-galaxy-s7/how-to/how-to-notes-root-install-xposed-unroot-t3411039
SM-G930V PIT filehttps://drive.google.com/file/d/1pn_m818zfnkpEL-GgcjQaRUz1VQqaEdG/view?usp=sharing
Steps:
1: Download SamFirm, Odin PrinceComsy, and the PIT file.
2: Extract and Run SamFirm ( Samfirm requires Microsoft Visual C++ 2008 Redistributable Package (x86) and Microsoft Visual C++ 2010 Redistributable Package (x86) can be found on microsofts website if you recieve an error when searching for firmware) .
3:In the firmware info box under Model enter SM-G930V and Region enter VZW. Make sure Auto is checked. and click check Update.
4: Next in the download box to the right make sure both CRC32 and Decrypt automaticly are both checked and click download. A save box will appear and save to where you need.
5: Once it is done Downloading and Decrypting navigate to where you saved the file and unzip the file. There are 5 files inside the zip (AP, BL, CP, CSC, CSC_HOME)
6: extract and open Odin PrinceComsy and click each one of the BL, AP,CP,CSC radio buttons and choose the matching file from the fimware unziped in Step 5. FOR CSC BUTTON FILE YOU MUST CHOOSE HOME_CSC FILE (TO KEEP YOUR DATA) OR CSC FILE (TO ERASE YOUR DATA). DO NOT CLICK START!!!!!
7:Extract the PIT file downloaded.
8: In odin click on the PIT tab and browse and select the file extracted in Step 7. DO NOT CLICK START!!!!!
9: Next go to the options tab and make sure Auto reboot, Re-Partition, and F. Reset Time are all checked.
10: Click Start and the phone will flash the files and reboot into recovery and finish installing and reboot a few times. wile rebooting it will boot back into recovery and say erasing. then the next reboot it will boot into the G930V firmware.
I hope this help Some people out there. If you have any questions post them below or PM me.
oddboy said:
I am creating this guide to convert convert the G930VL to G930V since i cant find a guide for android 7.0 and The G930VL firmware is no ware to be found. I have been a long time member and have flashed many roms on phones and normaly dont find a need to post but since i could not find much on the internet i decided to make a step by step guide.
I take no credit for creating any of the tools used in this guide as i was not the creator. I have only figured out the way to get the G930V firmware on to the phone.
I am not responsible for any bricked devices
You must have usb drivers installed
Tools:
SamFirm V0.3.6 (as of writing) https://forum.xda-developers.com/galaxy-tab-s/general/tool-samfirm-samsung-firmware-t2988647
Odin PrinceComsy https://forum.xda-developers.com/verizon-galaxy-s7/how-to/how-to-notes-root-install-xposed-unroot-t3411039
SM-G930V PIT filehttps://drive.google.com/file/d/1pn_m818zfnkpEL-GgcjQaRUz1VQqaEdG/view?usp=sharing
Steps:
1: Download SamFirm, Odin PrinceComsy, and the PIT file.
2: Extract and Run SamFirm ( Samfirm requires Microsoft Visual C++ 2008 Redistributable Package (x86) and Microsoft Visual C++ 2010 Redistributable Package (x86) can be found on microsofts website if you recieve an error when searching for firmware) .
3:In the firmware info box under Model enter SM-G930V and Region enter VZW. Make sure Auto is checked. and click check Update.
4: Next in the download box to the right make sure both CRC32 and Decrypt automaticly are both checked and click download. A save box will appear and save to where you need.
5: Once it is done Downloading and Decrypting navigate to where you saved the file and unzip the file. There are 5 files inside the zip (AP, BL, CP, CSC, CSC_HOME)
6: extract and open Odin PrinceComsy and click each one of the BL, AP,CP,CSC radio buttons and choose the matching file from the fimware unziped in Step 5. FOR CSC BUTTON FILE YOU MUST CHOOSE HOME_CSC FILE (TO KEEP YOUR DATA) OR CSC FILE (TO ERASE YOUR DATA). DO NOT CLICK START!!!!!
7:Extract the PIT file downloaded.
8: In odin click on the PIT tab and browse and select the file extracted in Step 7. DO NOT CLICK START!!!!!
9: Next go to the options tab and make sure Auto reboot, Re-Partition, and F. Reset Time are all checked.
10: Click Start and the phone will flash the files and reboot into recovery and finish installing and reboot a few times. wile rebooting it will boot back into recovery and say erasing. then the next reboot it will boot into the G930V firmware.
I hope this help Some people out there. If you have any questions post them below or PM me.
Click to expand...
Click to collapse
Thanks, your guide help me flash my phone and everything works except for sending text messages (and since smsc isn't working my voicemail doesn't either). Did you have this issue as well? My smsc is in the messaging app but it doesn't work. Receiving texts, Sending/receiving MMS, calls, 4g data all work.
ruinairas said:
Thanks, your guide help me flash my phone and everything works except for sending text messages (and since smsc isn't working my voicemail doesn't either). Did you have this issue as well? My smsc is in the messaging app but it doesn't work. Receiving texts, Sending/receiving MMS, calls, 4g data all work.
Click to expand...
Click to collapse
Double check your apn settings. Sometimes they get muddled. Also, my experience with this is that you have to make a call to get texts to work. I jest updated to oreo using jkruse post and it works much better than nougat. My apn was wrong and just changing the name to TRACFONE.VZWENTP fixed everything
Sent from my SM-G930V using Tapatalk
Hi can you please tell me if this guide will work to flash a Verizon s7 that is on TMobile nougat back to Verizon nougat so I can update to Oreo that k you
So my friend tried rooting his phone (VL model) and it's bricked. It has a boot loop with the installing system firmware screen. But I can boot into Odin download mode. I tried using this method and picking both CSC and home CSC. On the CSC one it will fail at emmc_appsboot.mbn.lz4 after the "single download" line.
The Home CSC, it will reboot after the RQT_CLOSE and RES OK and says pass for for set partitions, but when it reboots it goes to the installing system firmware bootloop
Any suggestions? He can't afford a new phone. And I'd love to help him fix it!
I have a copy of the SM-G930VL firmware.
Dreamer1186 said:
I have a copy of the SM-G930VL firmware.
Click to expand...
Click to collapse
I think i bricked my SM-G930VL from straight talk, it boots up but it immediately reboots after not even 10 seconds of being booted up. i think it was because i rooted and google apps mostly did not load, they had a loading circle but it never loaded so i decided i would try and go into recovery mode and clear/wipe the cache partition. im not quite sure if thats why i cant fully boot past the lockscreen, i tried a factory reset after attempting to boot into safe mode several times but it continues to reboot after the starting android screen, wont even let me setup the phone now.. its very frustrating and if the stock firmware will work, do you still have it? or would i need to try something else?
This method bricked my Straight Talk S7 by leaving it in a recovery loop. I was able to get it into download mode, then installing SM-G930VL Tracfone firmware with Android 6.0 using Odin PrinceComsy (no PIT file). Then, once it was working, I did official software updates through system update to get it up to Android 7.0. I originally had Android 8.0 before brick, but it is still doing updates after every install, so I'll check in if I was able to get it back to how it was before. I suspect that the PIT file used in this guide may be what is causing the recovery loop. I will try the SM-G930V conversion without it to see what happens. My ultimate goal here is to get my Straight Talk S7 rooted.
can you get me the link to SM-G930VL Tracfone firmware you used please
Hello!
There is a device with a broken screen that does not start. When you first boot there is an optimization of applications, then a reboot. And so in a cycle.
You need to pull out the data. OEM bootloader is blocked. ROOT rights are not present. ADB does not work.
Download Mode works. It is desirable to try to pull the data through it.
Tried to make a dump through the Samsung Odin version, where the "Dump" button remained, but in as a result, I got a file size of 1 KB, which, of course, is not a dump partition userdata. In new versions, this button is missing.
Also when running Recovery, apparently the device is trying to find the archive in the ZIP firmware (update.zip).
Please help copy the data from your device! In the device remained very valuable data that makes me not do a wipe data.
Dump with odin - nice idea! my oldest version is 3.09, which has a dump button, but always greyed. Are you shure, dump is possible in odin mode?
Hi,
Phone; SM-AF520F
My phone has been restarting on its own from the past month and I ignored it. It showed me occasionally Google services failed or system UI is not responding.
I factory resetted the phone as any noob would do and the restart occurrence went to only at night, which I was unbothered with. A little time passed and the phone went to the downloading sky blue screen.
I'm aware with flashing roms and stuff but I never really tried it. I tried everything;
i) Used Odin, three different versions
ii) Used Stock firmware, three different versions
iii) Used Smart switch
The phone only went in download phase and than in the phase where you press home button, volume and power and it shows fonts in the left hand corner. Odin always giving me errors, sometimes stucking on setting up connection.
Two errors:
i) There is no PIT partition
ii) Write operation failed
There are always these things happening.
When I restarted with volume down and power key, the system showed, there was an error and try smart switch, updated my drivers but when I go in the settings to emergency recover my phone, it does not show my phone.
After restarting the phone couple of time, Im in downloading mode again, in between the screen also turns full sky blue with no text.
I tried installing custom recovery but the image didn't load, ( I dont know what i am doing at this point, even if this was a good idea).
I have scavanged every forum, every post, everything on the internet but I just can't seem to fix it, I tried every possible thing and it just dosent work. I know it can be fixed but I don't know how. I know I'm doing something stupidly wrong but I can't seem to figure it out.
This is an old phone, I'm going to buy another one soon but I just hope it works for another week? Can I wipe the whole system and start from scratch (Which i dont know how to do).
Any type of help would be greatly appreciated, or just tell me to give up hope on it so I can just throw it away and move on.
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
matkali said:
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
Click to expand...
Click to collapse
Thank you for your response.
I did what you exactly said, previously it failed at the instant, now it moved one tab and than failed.
I tried the provided Odin, than tried two roms with, with the pit filed extracted and enabled re partition.
The error occurred: Complete(write) operation failed.
The error occurred every time I tried to flash, it never worked.
Do you think there is anything else to do?
Try this way to go download mode:
Press vol-down + power until phone restart
Then instantly press vol-up + Home + Power to going to download mode!
If it not works for you! You can use (eMMC programmer or easy JTAG) to writing rom on your phone memory (Last Option)!
I gave up on it and asked for professional help. Idk what he did, but he fixed the phone. It was sluggish at first but it works like a charm now.
It took 7 minutes to turn it on, than It said, there was an authorized user who tried to access your phone, use your previous email password to access your phone. I put it on my previous details and the works okay after some updates.
I wonder what he did? And i never knew android has a feature where if somone tries to reset your phone, google account locks it? Wow.
Is flashing a custom os a good idea? I'm afraid I'll brick it or something or just keep running one ui and wait for it to die again.
Thank you for your help btw, made me learn alot.
matkali said:
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
Click to expand...
Click to collapse
im having the exact same problem this guy has, installing a pit file will erase my data? if i use HOME_CSC will the pictures stay? i only care about the photos.
Welcome to this easy guide.
Time needed: 15 / 60min (depends on your internet connection)
Ease of operation: Very easy
Don't be fooled by the length of this guide ... the operations to be done are quick and easy.
NB: I state immediately that this procedure does not restore the state of Knox to 0x0 if by chance you have brought it to 0x1.
To date, this is an irreversible process.
In the next lines we will see how to restore our Samsung device to its original factory conditions, after unlocking the Bootloader, rooting and installing various types of custom installations, such as custom OneUI, AOSP or Google ROM.
It may happen that you want to go back to the original firmware of our Samsung, after trying various custom ROMs, after having rooted and modified the recovery, missing with the phone partitions, lost EFS folder or corrupt IMEI. The reasons can be many. This guide is aimed at all those who, with the classic Odin procedure to install the stock rom, are unable to restore the phone to normal operating conditions.
But it can happen to fail in this thing, even using Odin to put back the original software, Odin himself or the phone can crash to the BOOT partition or generate other errors, with VBMeta or generic errors, including partition ones.
So let's see how to solve all the inconveniences due to modding on our Samsungs to 99%. Let's begin!
- MATERIAL REQUIRED:
Latest version of Frija link
Latest version of Odin link
Samsung USB Driver link
File Manager zip (example 7zip) link
PC with Microsoft Windows 7-8-8.1-10-11
USB type C cable
1 - Download the latest stock firmware for our Samsung:
Download the latest version of Frija and once the program has started, enter the model code of your device and the abbreviation of your CSC.
Make sure the "Auto" checkbox is checked.
Once you have checked everything, click on "Check Update" and click on "Download". Wait for it to download.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Once you have downloaded the zip containing the various parts that make up the stock software (see image below), extract it to a folder of your choice. We will have 5 files in total.
2 - Retrieve the original PIT file
To recover the PIT file (partition list) for our device, go to the firmware folder you just downloaded with Frija, locate the "tar.md5" file with the words CSC_OXM_N............., right click on the it and select rename, adding ".zip" at the end to "transform" it into a compressed file that can be opened. This way you will have something like
"CSC_OXM_N975...............REV01_user_low_ship.tar.md5.zip"
Give the Ok and confirm the change of the file extension.
You should now have the same situation as you see in the image below. Total 5 files of which one is a ".zip" files.
Now open the file you just renamed with 7zip, the main window of the 7zip program will open with various files inside:
Now copy the "D2S_EUR_OPEN.pit" file by right clicking and selecting the "copy to ..." item and giving the ok without changing anything. The .PIT file will be copied to the same folder as the previously downloaded firmware.
Once this is done, the folder that appears will look like this (Now, the total files are 6 of which one is a ".zip" files):
Now just put the CSC_OXM ... file back to the previous condition, renaming it one more time and eliminating the ".zip" extension at the end of the name, in order to find an MD5 file again. This will be the file we will have:
"CSC_OXM_N975...............REV01_user_low_ship.tar.md5."
Now we have everything we need. If we have done everything correctly this is the final result (Total 6 files).
3 - Prepare and Configure Odin
Now open the latest version of Odin (as of May 2022 the latest version is 3.14.4), load the corresponding downloaded firmware files in the various slots (BL, AP, CP and CSC) as usual.
In the CSC box, upload the file labeled "CSC_OXM_N975 ............... REV01_user_low_ship.tar.md5."
Did you know that....
The CSC_OXM file is used to restore the internal memory as factory, this will delete all personal data in the phone memory, all applications and data associated with it.
The HOME_CSC_OXM file, on the other hand, will not act in any way on the internal memory. Useful if you want to update while remaining in the same type of ROM. Not recommended if your phone has a Custom ROM installed, as it may not start or give errors in previously installed applications.
If you want to do a clean install of the original ROM, always use the CSC_OMX file!
Click to expand...
Click to collapse
Once this is done, move (still in Odin) to the "Option" tab and check the following items:
Auto Reboot
Nand Erase
Re-partition
F. Reset time
The rest of the items MUST NOT BE SELECTED!
Again in Odin, this time go to the PIT tab, a warning message will appear, give the ok and select the first extracted file which has the unique name "D2S_EUR_OPEN.pit"
If you have done everything right you should have the same situation as the image below:
4 - Return the phone to the original firmware
Connect the USB type C cable to your phone and restart your phone in "Download mode" (check the right combination for your model), or use the Custom Rom to do this, usually all coustom roms or custom recovery offer reboot in Download mode (or Booloader).
In odin in the "Log" tab, you should see the word "Added" with the number of the port to which it is connected (example "0: [COM3]"), if so, press the START key of Odin and wait for the restart (this procedure will delete all data on your device).
If nothing appears, install the Samsung USB drivers and repeat step 4.
5 - Relock the BootLoader
To get rid of that fatal warning message when starting the phone that tells us that the BootLoader is unlocked once and for all, let's put it back in place, relocking the BootLoader.
(Image for demonstration purposes)
Turn off the phone, reconnect the USB cable and immediately press the Volume + and Volume- keys at the same time.
Return to Download mode (albeit a little different), with various options (actually only 3).
In this case, follow the second option (Volume up long press: Device unlock mode) hold down the Volume + key for a few moments until the message "Lock Bootloader?" Appears. To confirm everything, make a single click on Volume + (also in this case the phone will be formatted by the system again) and wait for a complete restart.
6 - Relock OEM (optional but recommended if you want to stick with the Samsung ROM)
Once your phone has restarted and the initial setup is complete, you can also disable the OEM unlock capability and reuse the security features.
To do this, go to Settings / Phone Information / Software Information and tap several times on the wording "Build version" in order to unlock the "Developer options". If prompted, unlock your smartphone with your PIN or sign.
Now go back to the main Settings page, open the Developer Options and check that the "OEM Unlock" item is disabled, otherwise disable it and restart the device.
Well now you have your Samsung with Original firmware again. Enjoy
ExileTM said:
Welcome to this easy guide.
Time needed: 15 / 60min (depends on your internet connection)
Ease of operation: Very easy
Don't be fooled by the length of this guide ... the operations to be done are quick and easy.
NB: I state immediately that this procedure does not restore the state of Knox to 0x0 if by chance you have brought it to 0x1.
To date, this is an irreversible process.
In the next lines we will see how to restore our Samsung device to its original factory conditions, after unlocking the Bootloader, rooting and installing various types of custom installations, such as custom OneUI, AOSP or Google ROM.
It may happen that you want to go back to the original firmware of our Samsung, after trying various custom ROMs, after having rooted and modified the recovery, missing with the phone partitions, lost EFS folder or corrupt IMEI. The reasons can be many. This guide is aimed at all those who, with the classic Odin procedure to install the stock rom, are unable to restore the phone to normal operating conditions.
But it can happen to fail in this thing, even using Odin to put back the original software, Odin himself or the phone can crash to the BOOT partition or generate other errors, with VBMeta or generic errors, including partition ones.
So let's see how to solve all the inconveniences due to modding on our Samsungs to 99%. Let's begin!
- MATERIAL REQUIRED:
Latest version of Frija link
Latest version of Odin link
Samsung USB Driver link
File Manager zip (example 7zip) link
PC with Microsoft Windows 7-8-8.1-10-11
USB type C cable
1 - Download the latest stock firmware for our Samsung:
Download the latest version of Frija and once the program has started, enter the model code of your device and the abbreviation of your CSC.
Make sure the "Auto" checkbox is checked.
Once you have checked everything, click on "Check Update" and click on "Download". Wait for it to download.
View attachment 5628035
Once you have downloaded the zip containing the various parts that make up the stock software (see image below), extract it to a folder of your choice. We will have 5 files in total.
View attachment 5629259
2 - Retrieve the original PIT file
To recover the PIT file (partition list) for our device, go to the firmware folder you just downloaded with Frija, locate the "tar.md5" file with the words CSC_OXM_N............., right click on the it and select rename, adding ".zip" at the end to "transform" it into a compressed file that can be opened. This way you will have something like
"CSC_OXM_N975...............REV01_user_low_ship.tar.md5.zip"
Give the Ok and confirm the change of the file extension.
You should now have the same situation as you see in the image below. Total 5 files of which one is a ".zip" files.
View attachment 5629261
Now open the file you just renamed with 7zip, the main window of the 7zip program will open with various files inside:
View attachment 5628037
Now copy the "D2S_EUR_OPEN.pit" file by right clicking and selecting the "copy to ..." item and giving the ok without changing anything. The .PIT file will be copied to the same folder as the previously downloaded firmware.
View attachment 5629463
Once this is done, the folder that appears will look like this (Now, the total files are 6 of which one is a ".zip" files):
View attachment 5629465
Now just put the CSC_OXM ... file back to the previous condition, renaming it one more time and eliminating the ".zip" extension at the end of the name, in order to find an MD5 file again. This will be the file we will have:
"CSC_OXM_N975...............REV01_user_low_ship.tar.md5."
Now we have everything we need. If we have done everything correctly this is the final result (Total 6 files).
View attachment 5629265
3 - Prepare and Configure Odin
Now open the latest version of Odin (as of May 2022 the latest version is 3.14.4), load the corresponding downloaded firmware files in the various slots (BL, AP, CP and CSC) as usual.
In the CSC box, upload the file labeled "CSC_OXM_N975 ............... REV01_user_low_ship.tar.md5."
Once this is done, move (still in Odin) to the "Option" tab and check the following items:
Auto Reboot
Nand Erase
Re-partition
F. Reset time
The rest of the items MUST NOT BE SELECTED!
View attachment 5628039
Again in Odin, this time go to the PIT tab, a warning message will appear, give the ok and select the first extracted file which has the unique name "D2S_EUR_OPEN.pit"
If you have done everything right you should have the same situation as the image below:
View attachment 5628043
View attachment 5628045
4 - Return the phone to the original firmware
Connect the USB type C cable to your phone and restart your phone in "Download mode" (check the right combination for your model), or use the Custom Rom to do this, usually all coustom roms or custom recovery offer reboot in Download mode (or Booloader).
In odin in the "Log" tab, you should see the word "Added" with the number of the port to which it is connected (example "0: [COM3]"), if so, press the START key of Odin and wait for the restart (this procedure will delete all data on your device).
If nothing appears, install the Samsung USB drivers and repeat step 4.
View attachment 5628041
5 - Relock the BootLoader
To get rid of that fatal warning message when starting the phone that tells us that the BootLoader is unlocked once and for all, let's put it back in place, relocking the BootLoader.
View attachment 5629449
(Image for demonstration purposes)
Turn off the phone, reconnect the USB cable and immediately press the Volume + and Volume- keys at the same time.
Return to Download mode (albeit a little different), with various options (actually only 3).
In this case, follow the second option (Volume up long press: Device unlock mode) hold down the Volume + key for a few moments until the message "Lock Bootloader?" Appears. To confirm everything, make a single click on Volume + (also in this case the phone will be formatted by the system again) and wait for a complete restart.
6 - Relock OEM (optional but recommended if you want to stick with the Samsung ROM)
Once your phone has restarted and the initial setup is complete, you can also disable the OEM unlock capability and reuse the security features.
To do this, go to Settings / Phone Information / Software Information and tap several times on the wording "Build version" in order to unlock the "Developer options". If prompted, unlock your smartphone with your PIN or sign.
Now go back to the main Settings page, open the Developer Options and check that the "OEM Unlock" item is disabled, otherwise disable it and restart the device.
View attachment 5629493
Well now you have your Samsung with Original firmware again. Enjoy
Click to expand...
Click to collapse
Hi there. I tried it and didn't work for me.
Tried with differents CSC too, but my phone doesn't start the system. Just starts the download and recovery mode
It doesn't even show up the charging screen when powered off
Tried so many things and I can't boot my system...
I made a post with the info about what happened:
Need help with semi-bricked Note 10 Plus (SM-N975F) - Stuck on recovery/download mode
Didn't know where to post this exactly, to be honest. This will be a long post I was flashing AOSP roms in the phone. Tried to go back to One UI for the VoLTE thing In one of the AOSP roms I couldn't install it in Lineage Recovery (older version...
forum.xda-developers.com
Please help...
Ok, tell me where you get stuck ... or can you follow the whole guide but then the phone doesn't start?
Is the model number of your Note10+ is SM-N975F?
What original CSC did you have before you root?
RedSpikeJr said:
Hi there. I tried it and didn't work for me.
Tried with differents CSC too, but my phone doesn't start the system. Just starts the download and recovery mode
It doesn't even show up the charging screen when powered off
Tried so many things and I can't boot my system...
I made a post with the info about what happened:
Need help with semi-bricked Note 10 Plus (SM-N975F) - Stuck on recovery/download mode
Didn't know where to post this exactly, to be honest. This will be a long post I was flashing AOSP roms in the phone. Tried to go back to One UI for the VoLTE thing In one of the AOSP roms I couldn't install it in Lineage Recovery (older version...
forum.xda-developers.com
Please help...
Click to expand...
Click to collapse
ExileTM said:
Ok, tell me where you get stuck ... or can you follow the whole guide but then the phone doesn't start?
Is the model number of your Note10+ is SM-N975F?
What original CSC did you have before you root?
Click to expand...
Click to collapse
I followed the full guide, but I got stuck after flashing the firmware in Odin. It shows the screen of "Erasing data", and after that, nothing more
Even after locking again the bootloader
And yes, I ticked what's needed in Odin and used the .pit file
My model it's SM-N975F
The original CSC it's ZTO. Flashed the latest firmware
Ok so with Odin it didn't give you any problem. Let's say he freezes when he does the first boot that does the factory reset. Right?
Well odd, because once the original firmware is installed, I don't see why it should crash on boot ... unless there is a hardware problem in the phone's internal memory.
I know it may sound trivial, but the usb cable you use is good and did you use the latest version of Odin?
Have you checked maybe if the internal memory is right for you. If it is 256Gb or 512Gb
You could try this, if you see that it does not start try to enter the recovery (the original one) and delete everything you can, like cache and do a reset data directly from the recovery. Then try restarting and see if it starts.
If it still doesn't boot, try this thing.
Install TWRP custom recovery and enter once installed.
Go to Wipe Section in TWRP, Repair or Change partition, System and Data, and Changed Ext4 to EXTFAT. And changed back to Ext4. Eventually rerun the guide again.
ExileTM said:
Ok so with Odin it didn't give you any problem. Let's say he freezes when he does the first boot that does the factory reset. Right?
Well odd, because once the original firmware is installed, I don't see why it should crash on boot ... unless there is a hardware problem in the phone's internal memory.
I know it may sound trivial, but the usb cable you use is good and did you use the latest version of Odin?
Have you checked maybe if the internal memory is right for you. If it is 256Gb or 512Gb
Click to expand...
Click to collapse
The USB it's the original from Samsung.
The device is 256GB
ExileTM said:
You could try this, if you see that it does not start try to enter the recovery (the original one) and delete everything you can, like cache and do a reset data directly from the recovery. Then try restarting and see if it starts.
Click to expand...
Click to collapse
Tried this already. Didn't work
ExileTM said:
If it still doesn't boot, try this thing.
Install TWRP custom recovery and enter once installed.
Go to Wipe Section in TWRP, Repair or Change partition, System and Data, and Changed Ext4 to EXTFAT. And changed back to Ext4. Eventually rerun the guide again.
Click to expand...
Click to collapse
I tried this but not in the process of "Do the format and then do the Odin process" so I can try
I'm trying now with USB OTG to know if I can flash the system.img (and know if from there I can solve this)
ExileTM said:
If it still doesn't boot, try this thing.
Install TWRP custom recovery and enter once installed.
Go to Wipe Section in TWRP, Repair or Change partition, System and Data, and Changed Ext4 to EXTFAT. And changed back to Ext4. Eventually rerun the guide again.
Click to expand...
Click to collapse
Tried from reset data on official recovery to doing the change of format in TWRP and the doing all of the process again. No success.
Also tried with USB OTG with system, vendor, product and boot image. Neither
One thing that happened is that when trying to change the system partition to exFAT, it gave an error (system is not mounted) but changed the format to vFAT. Changing it to another option doesn't give that error, so I tried to do with another option and back to ext4.
I don't think it's a physical issue, if turns on, there is some hope at least
There is almost certainly a solution to your problem. (have you tried to do "format data" and typed "yes" in TWRP recovery?). Anyway, it's night at my place now, I'll see tomorrow to think of some other solution.
Tried already. Also tried to format the data with fastboot (Lineage Recovery gives the option to fastboot in Samsung)
I have the exackt same problem with my note10+ with 256GB and dual sim. and the problem you describe is also 100% what i experienced and still have as an issue... If you get to the point where you can solve the issue then please write me my friend. I will do the same ofcourse... btw can you use your pen in TWRP? i can only mark the files but not click them to run...? i have the idea that the TWRP for our model isnt built right somehow..
I assume you haven't solved the problem yet. In these days I have looked around but I have not found much ...
I saw a video, which through the ADB shell a guy was able to find the list of all partitions with the numbers of all the blocks and information and practically managed to rebuild the system partition from scratch, but I don't know if it works on samsung.
This is video:
Then another thing, what procedure did you follow for rooting? You may have had problems during the rooting process.
I followed this guide:
To update the situation
The battery of the phone inflated like a balloon, so I needed to go to a technician. I don't know for sure if that was caused by something physical, but will update when have some news
Ok, let me know if the technician can get you to restart the phone, and out of curiosity, he can bring the knox back to 0.
Hi, I was trying this today and I'm stuck at "An error has occured while updating the device software."
Odin was stuck at product.img for over an hour so I restarted the phone using volume down and power.
I tried again and it keeps getting stuck at product.img while the phone shows this error. Please could you help me out?
I followed all the steps exactly as you said, but I noticed while in download mode that it showed Warranty Void: 1
I did not root the phone, only flashed Pixel Experience and now trying to go back to OneUI
aaaajwedk said:
Hi, I was trying this today and I'm stuck at "An error has occured while updating the device software."
Odin was stuck at product.img for over an hour so I restarted the phone using volume down and power.
I tried again and it keeps getting stuck at product.img while the phone shows this error. Please could you help me out?
I followed all the steps exactly as you said, but I noticed while in download mode that it showed Warranty Void: 1
I did not root the phone, only flashed Pixel Experience and now trying to go back to OneUI
View attachment 5647587
Click to expand...
Click to collapse
Hello, then, the Warranty Void at 1 is triggered when you install a non-original firmware (in this case the PixelExperience), or when you change Recovery (ex: the TWRP) or you run the ROOT.
Any other software that is not in original firmware triggers the Knox to 0x1 irreversibly.
In your specific case, by installing the LineageOS Recovery and the PixelExperence ROM you have triggered the Knox at 0x1.
I am sorry.
Coming to your problem, the model of your phone what it is (ex: SM-N975F) and the CSC (ex: ITV). Did you download the original software for your exact model? Did you extract the PIT file from the original firmware and put it in the Option tab in Odin?
ExileTM said:
Hello, then, the Warranty Void at 1 is triggered when you install a non-original firmware (in this case the PixelExperience), or when you change Recovery (ex: the TWRP) or you run the ROOT.
Any other software that is not in original firmware triggers the Knox to 0x1 irreversibly.
In your specific case, by installing the LineageOS Recovery and the PixelExperence ROM you have triggered the Knox at 0x1.
I am sorry.
Coming to your problem, the model of your phone what it is (ex: SM-N975F) and the CSC (ex: ITV). Did you download the original software for your exact model? Did you extract the PIT file from the original firmware and put it in the Option tab in Odin?
Click to expand...
Click to collapse
Hello, I got it working just now by using a different cable and USB port. The procedure completed and the phone restarted by itself, and now its perfectly fine. Thank you so much for your help.
Yes, the phone is an SM-N975F. Despite Knox being tripped, my banking and payment apps are still working so I'm happy
I'm sure your article will be helpful to many more users. Thank you!
aaaajwedk said:
Hello, I got it working just now by using a different cable and USB port. The procedure completed and the phone restarted by itself, and now its perfectly fine. Thank you so much for your help.
Yes, the phone is an SM-N975F. Despite Knox being tripped, my banking and payment apps are still working so I'm happy
I'm sure your article will be helpful to many more users. Thank you!
Click to expand...
Click to collapse
OK well. Glad it was helpful. Yes, however, until you root all the apps will work. The only one are some applications by Samsung that will no longer work because they are based on the knox.
Otherwise like Google Pay, all banking and account apps, software updates should work smoothly.
Hi, is this guide usable for the S22 snapdragon version? My device is rooted, and I want to back to original firmware.