As a general FYI, if you think you need to repartition your phone it is also possible that your phone has experienced:
a) A hardware issue, possibly partial or total emmc failure.
b) A mismatch between bootloader (sboot.bin) and trustzone (tz.img) versions. See this post or my MK6 stock thread for some possible options to fix this.
As a step of last resort to recreate the partition table on your phone, a pit file may be what you need. This can be done in either Odin or Heimdall.
Warning - repartitioning your phone may erase all data and might cause other unintended consequences. You assume all risk.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------
To use a pit file in Odin, this is typically done as part of a flashing a stock rom package, like the LJ2 or MA4 package for the i317 (or similar package for the i317m). You specify the pit file in the PIT section, make sure the repartition box is checked, and then add the rom package in the PDA section like usual.
If you are running an official 4.3 or later bootloader you will not be able to successfully flash a stock firmware package that contains earlier bootloaders - Odin will hang and you will need to find a different stock package to flash that does not contain a bootloader. (i.e. If you took the the i317 4.3 OTA and are running the MK6 bootloader or a later bootloader, you'll want to avoid UCAMA4)
The attached zip includes pit files for both the i317 and the i317m. The partition mapping is the same for both (see the included analysis files), but the pit files have unique security signatures which are accepted only by the bootloader of the specific model phone for which they are intended. I've tested the file for the i317 and can confirm that it works as intended. The file for the i317m was pulled the same way by an XDA member (thanks @plemen !) with an i317m and I've confirmed it is formatted correctly. It has now been confirmed as working.
If you want to learn a bit more about pit files, check out this thread by Adam Outler:
http://forum.xda-developers.com/showthread.php?t=2540480
Very interested in this, as I need the pit file for my I317. Question about the bootloader, though.... I've never taken an OTA, just flashing CM and OmniROM nightlies (was on 4.4.2 when my phone committed suicide). Should I be safe to use this pit file? And what factory firmware would you recommend to go with it?
pit files should be back in a day or two (I'll be testing over the weekend).
Depending on what happened to your phone it's still highly probable that your pit (partition) data is fine. There's a way to confirm this using Heimdall - when time permits I'll add instructions to post #2. That's a safer first step than attempting a repartition.
As for bootloader and firmware - if you've never taken an OTA, and you're not on a 4.3 bootloader your best bet for stock firmware is UCAMA4. It's a more complete and somewhat newer package than the other option (UCALJ2). You can get this from sammobile, or a mirror copy I have linked in post #2 here:
http://forum.xda-developers.com/showthread.php?t=2589891
that post also has information on a couple apps you can load that will allow you to check which bootloader you have loaded once your phone is operational.
Thanks for doing this! Did you have any luck over the weekend? Looking to re-partition as I'm unable to mount.
anine said:
Thanks for doing this! Did you have any luck over the weekend? Looking to re-partition as I'm unable to mount.
Click to expand...
Click to collapse
I expected a test phone on Saturday that didn't arrive until Tuesday thanks to the USPS getting the day off on Monday. Once I confirm the files work as intended I will repost them.
As for the issue you are having - what partition isn't mounting? Can you provide more detail?
Zen Arcade said:
I expected a test phone on Saturday that didn't arrive until Tuesday thanks to the USPS getting the day off on Monday. Once I confirm the files work as intended I will repost them.
As for the issue you are having - what partition isn't mounting? Can you provide more detail?
Click to expand...
Click to collapse
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Help
anine said:
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Click to expand...
Click to collapse
I desperately need this PIT file as well.. not on 4.3 however..I can get to download mode and into recovery but it spits a bunch of errors about unable to mount /cache etc...
anine said:
The Note 2 (ATT) suddenly rebooted and stuck on the "Samsung Galaxy Note 2" screen. A couple reboots and a battery pull did not solve the issue. I even let the phone stay on the screen in the event it needed to do some sort of repair.. but after an hour, nothing changed.
I loaded CWM recovery and got recovery mount errors. Also, I am unable to mount any of the internal file system when attempting from the advanced menu. After a couple of hours of following tutorials I went into download mode and installed the stock ATT rom. It was successful but still did not boot (attempted this twice). I came upon a few suggestions for similar issues that said the PIT file was needed to repartition. I used Beanstalk 4.4.2 before the crash.
Click to expand...
Click to collapse
The symptoms you describe are similar to those I've seen on the Q&A forum recently. I don't want to be the bearer of bad tidings, but I suspect you have a partial emmc (hardware) failure.
My time during the week is limited so I expect to have testing done this weekend.
terpencar said:
I desperately need this PIT file as well.. not on 4.3 however..I can get to download mode and into recovery but it spits a bunch of errors about unable to mount /cache etc...
Click to expand...
Click to collapse
I had similar issue, and was able to resolve it by following this thread. YOu need to restore factory original by following this thread from XDA.
Please don't forget to Thank
The files provided are only for phone I317 and not I317M
http://www.androidfilehost.com/?fid=23060877490003986
Instructions:
1. Download "back to stock" zip folder I uploaded. It contains all the files needed. No need to search around.
2. Unzip the file and extract the folder to your desktop.
3. Open folder and install Samsung drivers if not already done so.
4. Now make sure you have root and custom recovery on the phone. Turn the phone off. Hold volume up, home and power button at the same time.Wait till u see custom recovery screen and then let go off all the buttons.
5. Once in recovery... delete data, system, cache, dev cache like you want to flash a new rom. Turn the phone off by pulling the battery or see option for power off device under custom recovery.
6. Once the phone is completely off lets get into download mode. Hold volume down, home and power button until you see the screen with an option to press volume up to get into download. Press volume up to enter download mode when asked.
7. Now open odin3.07 I provided in the folder u downloaded. Once open connect your phone via usb. Windows should install device drivers. Once thats done, you should see com## on the Odin software.
8. On odin software you should see button called PDA. Click on it and browse to the file called KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user _low_ship.tar. in the folder provided by me. select it and hit ok. Odin will process the file. It will take max 2 to 3 min.
9. Before you click start on Odin make sure auto reboot and F. reset time is checked only. Everything else unchecked. Click start button. Odin will start flashing the factory firmware. It will take time.
10. Once Odin is done flashing. phone will reboot. Now you can disconnect the usb cable. When phone is fully rebooted, skip all the prompt and get to home screen.
11. Turn the phone off again and get into download mode. Connect usb cable to computer with Odin open. Click Pda and select file called CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.tar. Let Odin process it and then click start. Once flashing the root file is done. Phone should reboot to home screen. Now you have root. The reason we need root is to get rid of counter # in download more. It should say zero.
12. Connect your phone to computer while on the home screen. Open phone internal storage and go to download folder and copy Triangle away.apk into it.
13. Go into settings and security and check unknown sources.
14. Go to apps and open application "my file". Go to download folder and select triangle away application to install. install it. Open application application and scroll down and select reset counter option. Make sure your are connected to wifi. Confirm you phone is I317 and triangle away will download the file. Your phone should reboot into some type of reset counter recovery screen. follow the instruction on the screen to reset the counter. After that phone should reboot.
15. Once rebooted uninstall triangle away apk. Now open super user application and scrool down and click fully unroot. When done go into stock recovery and clear data and cache. reboot phone. All done. Your counter is set to zero. Your phone should read normal under settings.
You can update your phone under settings from att servers.
Enjoy.
Thanks to chainfire for his triangle away app and root for our device.
rob_z11 said:
I had similar issue, and was able to resolve it by following this thread. YOu need to restore factory original by following this thread from XDA.
Please don't forget to Thank
The files provided are only for phone I317 and not I317M
Instructions:
1. Download "back to stock" zip folder I uploaded. It contains all the files needed. No need to search around.
2. Unzip the file and extract the folder to your desktop.
3. Open folder and install Samsung drivers if not already done so.
4. Now make sure you have root and custom recovery on the phone. Turn the phone off. Hold volume up, home and power button at the same time.Wait till u see custom recovery screen and then let go off all the buttons.
5. Once in recovery... delete data, system, cache, dev cache like you want to flash a new rom. Turn the phone off by pulling the battery or see option for power off device under custom recovery.
6. Once the phone is completely off lets get into download mode. Hold volume down, home and power button until you see the screen with an option to press volume up to get into download. Press volume up to enter download mode when asked.
7. Now open odin3.07 I provided in the folder u downloaded. Once open connect your phone via usb. Windows should install device drivers. Once thats done, you should see com## on the Odin software.
8. On odin software you should see button called PDA. Click on it and browse to the file called KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user _low_ship.tar. in the folder provided by me. select it and hit ok. Odin will process the file. It will take max 2 to 3 min.
9. Before you click start on Odin make sure auto reboot and F. reset time is checked only. Everything else unchecked. Click start button. Odin will start flashing the factory firmware. It will take time.
10. Once Odin is done flashing. phone will reboot. Now you can disconnect the usb cable. When phone is fully rebooted, skip all the prompt and get to home screen.
11. Turn the phone off again and get into download mode. Connect usb cable to computer with Odin open. Click Pda and select file called CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.tar. Let Odin process it and then click start. Once flashing the root file is done. Phone should reboot to home screen. Now you have root. The reason we need root is to get rid of counter # in download more. It should say zero.
12. Connect your phone to computer while on the home screen. Open phone internal storage and go to download folder and copy Triangle away.apk into it.
13. Go into settings and security and check unknown sources.
14. Go to apps and open application "my file". Go to download folder and select triangle away application to install. install it. Open application application and scroll down and select reset counter option. Make sure your are connected to wifi. Confirm you phone is I317 and triangle away will download the file. Your phone should reboot into some type of reset counter recovery screen. follow the instruction on the screen to reset the counter. After that phone should reboot.
15. Once rebooted uninstall triangle away apk. Now open super user application and scrool down and click fully unroot. When done go into stock recovery and clear data and cache. reboot phone. All done. Your counter is set to zero. Your phone should read normal under settings.
You can update your phone under settings from att servers.
Enjoy.
Thanks to chainfire for his triangle away app and root for our device.
Click to expand...
Click to collapse
Thanks.. It just hangs at system.img in odin
Nice job Zen
Sent from my SGH-I317 using XDA Premium 4 mobile app
Pit files are back up and attached to the OP. The i317 pit file is tested and confirmed working.
The i317m file is identical, except for the security signature. I'm currently looking for someone with a healthy i317m willing to test flash the i317m pit file to confirm it works. (I would do this myself, but I don't have an i317m).
Unfortunately it did not work for me. emmc failure suspected. Strange thing is that in ODIN I can still "Successfully" install a ROM.. and even the PIT file succeeded. I still got a logo screen for several minutes.
Fortunately for me, I have an additional mainboard from a otherwise damaged note 2. I'll be swapping that out.
Thank you anyway. Hope your file helps others!
My phone was not booting and stopped at Samsung logo. After the pit file and stock rom, my phone is live again. I am still having issue with storage but at least I have good starting point.
thanks
Works fine on i317m
anine said:
Unfortunately it did not work for me. emmc failure suspected. Strange thing is that in ODIN I can still "Successfully" install a ROM.. and even the PIT file succeeded. I still got a logo screen for several minutes.
Fortunately for me, I have an additional mainboard from a otherwise damaged note 2. I'll be swapping that out.
Thank you anyway. Hope your file helps others!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2626593
qkster said:
http://forum.xda-developers.com/showthread.php?t=2626593
Click to expand...
Click to collapse
See posts #9 and #13 on the thread above for the specific potential solution to try.
Corrupt pit file it says. for note 2 att help
I have a Att note 2 i flash the mj9 firmware using mobile odin first. Then i formatted storage, data, system, and cache. And now its says i have NO ios Installed with is true but when i try flashing another rom in TWRP it fails iv'e try stock ATT, Jedi Rom, MeanBean Rom. now i tryed to flash stock firmware through J Odin but it always say corrupt pit file...Someone Please Help MEE
kumar_420 said:
I have a Att note 2 i flash the mj9 firmware using mobile odin first. Then i formatted storage, data, system, and cache. And now its says i have NO ios Installed with is true but when i try flashing another rom in TWRP it fails iv'e try stock ATT, Jedi Rom, MeanBean Rom. now i tryed to flash stock firmware through J Odin but it always say corrupt pit file...Someone Please Help MEE
Click to expand...
Click to collapse
Err mj9 is verizon haha
Sent from my lightning fast Note II running MeanBean 2.0 SuperCharged
Related
I really can't get this program to work. I followed the wiki to the T. Neither of the 3 options work. The only thing i notice that is different is the 3 option
If you get a FAILED error after it writes "param.lfs", try this method:
1. Reboot the phone and reset Odin
2. Load the pit file and place the tar in the Phone section
3. Start the recovery
4. The process will hang while writing "factoryfs.rfs"
5. Reboot the phone and reset Odin
^^ I never get factoryfs.rfs just the same old param.lfs error
I came from EB13 & did one click root clockwork 3.0.0.5/6. After i tried to boot into recovery it coverted everything into EXT4 when the phone did not work after that i tried to use Odin to flash back to EB13. I was able to apply syndicateROM through clockwork but it still does not turn on. When i try to turn on my device I don't get the Samsung boot logo i get 2 icons. Left icon is a phone right icon is a computer...really don't know what else to do. Appreciate any help
Try using Odin without the pit file and put the tar in the PDA section. If that doesn't work try redownloading the tar file again. It might have been a bad download.
Sent From My Evo Killer!
Unfortunately I tried that already. Redownloaded and without the pit file
Try a different USB cable - the stock one sucks.
castkel said:
I really can't get this program to work. I followed the wiki to the T. Neither of the 3 options work. The only thing i notice that is different is the 3 option
If you get a FAILED error after it writes "param.lfs", try this method:
[SIZE="6" This worked for me -- disclaimer : i do not take responsibility if your car dies your phones blows up in a bundle of fire or cant work if cats fly and scratch your face if gas prices go to $5 ----- but this might help you [/SIZE][/COLOR]
1. Reboot the phone and reset Odin
2. Load the pit file and place the tar in the Phone section
3. Start the recovery
4. The process will hang while writing "factoryfs.rfs"
5. Reboot the phone and reset Odin
^^ I never get factoryfs.rfs just the same old param.lfs error
I came from EB13 & did one click root clockwork 3.0.0.5/6. After i tried to boot into recovery it coverted everything into EXT4 when the phone did not work after that i tried to use Odin to flash back to EB13. I was able to apply syndicateROM through clockwork but it still does not turn on. When i try to turn on my device I don't get the Samsung boot logo i get 2 icons. Left icon is a phone right icon is a computer...really don't know what else to do. Appreciate any help[/QUOTE]
youtube odin and you should get a vid help
1. restart your computer
2. take the battery out your phone wait till your computer reset
3. put the battery back into the phone WHEN COMPUTER HAS FULLY STARTED UP
4. open ODIN ... [url]http://www.mediafire.com/?5w7sb1iq7webt4l[/url] just incase u didnt have it already
5. phone in download mode the number 1 and power button
6. plug it into the computer you should see your phone in a higlight yellow code pop up in ODIN ...
7. there are 2 things checked 1 called AUTO REBOOT ( [COLOR="Red"]leave it checked )
8. UNCHECK THE F RESET TIME
9. just load the TAR into PDA . for whatever phone ur using .......... if you need to download a new tar then do so best wat to find multiple versions is usually GOOGLE IT EX: samsung epic eb13 tar
10. ONLY PDA
1.. hit start and watch the MAGIC HAPPEN
Click to expand...
Click to collapse
k0nane said:
Try a different USB cable - the stock one sucks.
Click to expand...
Click to collapse
Yeah the stock one doesn't even work for me. Windows 7 doesn't recognize it I'm actually using the HTC evo cable. This cable has flashed a Moment and Intercept several times
I seen the video as well. I wish mine worked that flawless. I even tried a different PC. Back/front usb ports. Same difference always hangs at the same error "param.lfs"
O.k my wife got an AT&T Samsung Galaxy S3 when they first came out I bought it for her and it has this rom build on it l747UCALG1 and mine which I just bought about three days ago have this build on it l747UCALH9. Her build I was able to root if need be but my phone I can't and I am already on 2 count of the custom binary and I can't reset it since some how I can't root the phone the developers are seeing all of this stuff that we are doing to the phones and I believe they are trying to stop us. But anyway can some one tell me since I have a copy of her stock Firmware how can I just flash my phone or what have you with her stock firmware which is l747UCALG1 so I can root my phone. Also if you don't mind please leave me a clear step-by-step way to do it and if it works without doing any damage at all to my phone, and if I want to later go back to the stock that is on my phone now I can but I don't think I will unless I have to send or take it in ever for warranty repair or just sale it. If this works right leave me your e-mail or if you have a paypal account give me that address or what have you and I will send you a donation.. (Thanks)
Sincerely,
System Network Admin
http://forum.xda-developers.com/showthread.php?t=1739426
OR
http://forum.xda-developers.com/showthread.php?t=1746665
How to Revert to Old Firmware & Root Newest Release -
Hello and welcome to XDA.
I understand your concern to root your device especially with it being on the latest firmware, but I will do my best in order to explain every step to you in the utmost detail. I am currently on I747UCLH9 with a Custom ROM. Meaning I kept the Modem & Bootloader and kicked the Kernel and Firmware. Before I begin, I would like to ask you to thank to all the Developers / Posters who made & put this content together as this would not be possible without them. I will link all of their original posts at the end of this. Be sure to give credit to every one of them and please make sure to give thanks to them. I take absolutely NO CREDIT for any of these links/steps whatsoever. I simply researched and compiled them in order to help you. With that being said, let us begin.
Before anything you must remember this. After you are finished downloading whatever items you need, you MUST (and I cannot stress this enough) FACTORY RESET YOUR DEVICE. Reason being is because a lot of other people have tried this same process of downgrading without wiping and ended up getting startup boot errors. Be sure to NOT sign into your Google account. This is just a warning, follow the steps below to know when you should begin this process.
All files you download should be saved on your desktop. Personally I prefer to make a separate folder for these kind of delicate things. Keeps it organized so you don't forget where you are.
Make sure your phone IS NOT plugged in to your computer as of right now & you have NO external SD card.
Now;
Let's begin.
Before you start be sure you have the Samsung USB drivers installed. Which you can get from Samsung's website or here.
Samsung USB Drivers
Also be sure that you have WinRAR installed as well which you can get right here.
WinRAR
To be on the VERY SAFE side you must download ADB (Android SDK). What you must do is when it asks you for where you would like to install it, you MUST ONLY CLICK "Local Disk C:" . AND THATS IT. The best thing is to keep it here so when you have to execute a command line, it will be very simple. You will have a folder called "android" here. THAT IS YOUR ADB FOLDER. You will understand what I mean shortly. *Note* this is for CWM-T (ClockworkMod Touch).
Android SDK
1. Download the stock rooted LG1 Firmware. I747UCLG1 Stock + Root Only.
2. Right-Click the LG1 Firmware you just downloaded and extract it. It is currently root69.stock_ATT_I747UCALG1.7z ; the extraction process will turn it into the correct .tar file (Flashable file type with Odin)
3. Now that you have the Stock ROM, you need..well ODIN! Here's the link. Odin 3.07.
4. Since it is in .zip format you need to extract this as well. You will end up with 4 files. Right-Click on the Odin3 v3.07.exe and run it as administrator. Now you are at the Odin screen with nothing there -_-".
5. Factory reset your phone. Just let it boot up but DO NOT sign into your Google account, just click through skip everything head straight to your Settings, then Developer Options & make sure USB Debugging is enabled/checked. Back out of your settings completely and you are at the home screen.
6. Now, just hit the power button and turn your device off. After it is completely turned off hold the Volume Down + Home button. While holding these 2. Press and hold the Power button. You should now be holding all three buttons at the same time waiting for a green lettered screen to come on (Download Mode). Use the phone keys to select the option to continue. Your phone will now say Downloading, do not turn off device. (Or along those lines).
7. After selecting the option that sends your phone to the screen with the text "Downloading, Do not turn off device." You should be holding your phone in hand with USB plugged into your computer but your device is not connected. Odin is open on your computer screen with nothing still. From here just plug your phone in and you will see a pop-up in the first box of many under the Odin logo which says "COM: #".(#: Being a select number of your device. This is of no importance, as long as you see this pop up.) Once you see this your phone will be ready to be flashed back. Just click the PDA button and browse to the root69.stock_ATT_I747UCALG1.tar file. (Be sure you click the .tar and not the .zip.)
8. Check to make sure no other boxes should be checked except for Auto-Reboot.
9. Press Start and wait for the process to finish.
10. Everything should go through fine and your phone will start back up and you will be on LG1. You are now on stock firmware BUT rooted. Unplug your phone, Skip past everything once again and make sure USB Debugging is enabled. Keep your phone unplugged & don't forget to close ODIN.
Now before you do anything. You need a Custom Recovery AKA CWM. Well in this case we will be installing the latest touch version.
11. Download the latest ClockworkMod Touch from here. This link is saved in a way specifically from their website. You can either go to www.clockworkmod.com and browse the ROM Manager tab for the 6.0.1.4 Recovery. OR you can just right click the link provided right here and press "Save As..." this file will come up and asked to be saved as recovery-clockwork-touch-6.0.1.4-d2att.img. RENAME IT AS "recovery.img" without the quotes & save it.
ClockworkMod Touch 6.0.1.4
12. Now that you have this file. Plug in your phone to your computer and in the root folder of your phone storage and copy the recovery.img file to it; which is the first folder that pops up when you press open when you plug your phone in. (Remember no SD CARDS!)
13. Now, click the Start button on your taskbar and in the search bar type cmd. Now you will see cmd.exe; press enter and you will see the Command Prompt open. If you saved the Android SDK the way I told you to, you can copy and paste the line below. If you saved it somewhere else you can change the folder simply by browsing to the android folder. Make sure you click on the "platform-tools" folder. NOT the "platform" folder. Also whichever directory it is you must add a "\" at the end so it will find the location correctly.
cd C:\android\platform-tools\
14. Now you are in the directory time to run ADB Shell and flash that recovery! Copy and paste or type the following; I recommend you copy and paste the last line as it gets tricky. After the SU command your phone will be detected.
First you type adb shell
following that su
and finally dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p18
As you can see in the last command it is named recovery.img there are no special characters or numbers or symbols to mess with the flashing. After you run this command you will an output similar to the following.
14004+0 records in
14004+0 records out
7170048 bytes transferred in 1.430 secs (5014019 bytes/sec)
Finish up this step with the following command
reboot recovery
15. Your device will now restart and head straight into recovery. Congrats you now have LG1 Stock + Root with CWM-T. Unplug the USB and press "Reboot System".
TO UPGRADE BACK TO LH9 WITH ROOT AND CWM-T
Before I begin.
You must remember that this step REQUIRES you download 4 files to go on the root of your phone memory. Your phone should now be on the home screen. Plug it in and open your phone memory. With that being said you need the following files. The Rom, Modem, Bootloader, and Kernel. You will be flashing them in this following order as well.
16. Download the following pieces and save them to the root of your phone's memory. Be sure to remember which file has what name so when you enter the recovery you aren't lost as to which to flash first.
I747UCLH9 ROM Download
I747UCLH9 Modem Download
I747UCLH9 Bootloader Download
I747UCLH9 Kernel Download
17. After everything has finished transferring, remove the phone from the computer and turn your phone. Remember how you got into download mode? Well instead of holding Volume Down + Home, you hold Volume Up + Home. While holding these two press and hold your power button until you see it says Samsung Galaxy S III. If you look at the top left hand of the screen while it's JUST turning on. You will see some blue text flash. When you see that you know your entering the recovery and can release the buttons.
18. You are back at the recovery. You must now do the following. Touch the options as I list them. Follow these steps precisely.
- Wipe Data/Factory Reset
- Yes -- Delete all user data
- Wipe Cache
- Yes - Wipe Cache
- Advanced
- Wipe Dalvik Cache
+++++Go Back+++++
- Install Zip from SD Card
- Choose zip from SD Card
Now choose them in the following order, ROM, Modem, Bootloader, and finally Kernel.
WAIIIITTTTTTTT! After you are finished flashing the Kernel you MUST do the following. Click options as I state them.
- Wipe Cache
- Yes - Wipe Cache
- Advanced
- Wipe Dalvik Cache
- Advanced
- Fix Permissions
+++++Go Back+++++
Reboot System
19. Wait for your phone to reboot and NOW you can sign into your Google account. Go past everything go into your App drawer first and check for Superuser/SuperSU once you see that, go into your settings and check your ROM, Modem, Bootloader, Kernel. Yes. They are bone stock with root. Congrats you achieved maximum upgrade with root.
Now I would like to give my shout-outs; Thanks; and share the following posts that helped me compile this. I couldn't have done it without you guys.
neverends - Samsung Drivers & Odin provided. Steps to flash with Odin as well.http://forum.xda-developers.com/showthread.php?t=1722686
mrRobinson - I747UCLG1 Stock root injected file. Location of Odin, and commands to execute ADB shell to flash recovery.
http://forum.xda-developers.com/showthread.php?t=1739426
drothenberger - Provided CWM Flashable version of I747UCLH9. Blessing, really. Stock root with latest FULL update without having to revert back to LG1 stock.
http://forum.xda-developers.com/showthread.php?t=1896773
ALSO
Thanks to you all above; the CWM Team, CM10/AOKP Team, Moderators & Posters alike. None of this would have been possible without you. Keep up the good work. Bless -
jaysoblitzed said:
Hello and welcome to XDA.-
Click to expand...
Click to collapse
You made an awesome guide!! Hope he made a generous donation. Thanks!!
werked said:
You made an awesome guide!! Hope he made a generous donation. Thanks!!
Click to expand...
Click to collapse
Thank you, I really appreciate that. I don't accept donations I simply did it to help those who wanted/needed it
Sent from my T&K Blessed SGH-I747
I do not see the 4 download links for the ROM, Modem, Bootloader and Kernel. Can you post them.
I will fix the links but if you simply look at the people / threads I have given credit to at the bottom of my guide you will see drothenberger's thread. He has the original links there. Mind you, you MUST scroll down to the part where it says "PIECES:" and download following his links. Don't worry I will re-post them accordingly.
Sent from my T&K LH9 Blessed SGH-I747
Does upgrading from rooted LH9 from a rooted LG1 trip flash counter since we are installing 4 separate files instead of 1 .tar?
thanks!
Alright, so i have a Galaxy s3 (sgh-i747) and i rooted it with philz bootloader
So i was going to install a custom rom, so i had to wipe.
I downloaded the rom, and wiped.
But then i realized i actually never put the ****ing rom on the phone and now my phone has no rom loaded.
I can still boot into download/recovery
I really need help with this, what are my option?
So my phone is not rooted any more i guess because the recovery/bootloader is the default one
I still really need help with this
Ozzie 45 said:
I still really need help with this
Click to expand...
Click to collapse
Do you remember what (stock) firmware or Android version you were on before the attempted installation? Your best option now would be a return to stock. If you were on anything earlier than 4.3 (e.g. 4.1.2 or 4.1.1) you could try using Odin to flash 4.1.1 since you can get into download mode. To do this take the following steps ..
1. Download the required files via the following link <http://fortedge.com/downgrade.html>and extract the Odin flashable file
2. Install Odin
3. Boot into download mode and flash via Odin
OR you could find the correct stock image via the following discussion thread and flash via Odin. This would be a complete stock file that will flash all partitions including bootloader, modem, kernel and system.
http://forum.xda-developers.com/showthread.php?t=1739426
If you were on Android 4.3, then you cannot use the above method or flash via Odin and any attempt to do this will create more bother for you. In this case, you would need to flash custom recovery via Odin and restore the stock recovery image via custom recovery. Please download the stock recovery file via the following the thread ...
http://forum.xda-developers.com/show....php?t=2658486
If you need any further detailed steps on how to complete this, please do not hesitate to holler.
Larry2999 said:
Do you remember what (stock) firmware or Android version you were on before the attempted installation? Your best option now would be a return to stock. If you were on anything earlier than 4.3 (e.g. 4.1.2 or 4.1.1) you could try using Odin to flash 4.1.1 since you can get into download mode. To do this take the following steps ..
1. Download the required files via the following link <http://fortedge.com/downgrade.html>and extract the Odin flashable file
2. Install Odin
3. Boot into download mode and flash via Odin
OR you could find the correct stock image via the following discussion thread and flash via Odin. This would be a complete stock file that will flash all partitions including bootloader, modem, kernel and system.
http://forum.xda-developers.com/showthread.php?t=1739426
If you were on Android 4.3, then you cannot use the above method or flash via Odin and any attempt to do this will create more bother for you. In this case, you would need to flash custom recovery via Odin and restore the stock recovery image via custom recovery. Please download the stock recovery file via the following the thread ...
http://forum.xda-developers.com/show....php?t=2658486
If you need any further detailed steps on how to complete this, please do not hesitate to holler.
Click to expand...
Click to collapse
Yes, i was on Android 4.3
Can you please re-link that? The URL is broke
Ozzie 45 said:
Yes, i was on Android 4.3
Can you please re-link that? The URL is broke
Click to expand...
Click to collapse
I'm also going to need guidance on flashing custom recovery via Odin and restore the stock recovery image via custom recovery
Ozzie 45 said:
I'm also going to need guidance on flashing custom recovery via Odin and restore the stock recovery image via custom recovery
Click to expand...
Click to collapse
You will find the full link here ...<http://forum.xda-developers.com/showthread.php?t=2658486>
Download Odin.
http://fortedge.com/downloads/Odin307.zip
Download the Odin flashable custom recovery file via the following link ...
<http://techerrata.com/browse/twrp2/d2att>. You need one of the more recent images ending in *.tar e.g. the one below
<http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.0-d2att.tar>
Install Samsung Kies on your PC if you don't have this already (this will be useful for the drivers)
Install the twrp tar file to an easily remembered location on your PC
Extract the Odin zip to get the executable file (*.exe)
Click on the exe file to run Odin
Now boot your phone into download mode by powering off completely then holding down the Power + Home + Volume Down buttons simultaneously until you see a warning message.
Press the Volume Up button to continue
Connect your phone to the computer with a good quality micro-USB cable
If everything has been done OK, Odin should immediately recognize your phone and you should see a message saying "Added" in Odin. If you don't see this, then you may need to check the drivers are properly installed.
Click on the PDA tab in Odin and navigate to the twrp tar file you earlier downloaded. Select this file and click OK.
You should have the Auto-Reboot and F-Reset Time boxes checked in Odin. Please do not check or uncheck any other boxes!
Click on the Start button at the bottom to start flashing TWRP and wait until you see PASS and a green (or blue) box fully displayed. Your phone will automatically reboot after this although it may not be able to boot since you don't have an OS installed. You may disconnect the cable and close Odin after you see the PASS message. If you see FAIL, then disconnect, remove the phone battery and try again.
If you successfully flash TWRP, then you may proceed to reinstalling your ROM.
1. Download the zip file in the thread below <<http://forum.xda-developers.com/showthread.php?t=2658486>>
2. Save to a recognizable location on your phone's SD card. If you can't install files to your phone via your PC, then you may save to a micro SDHC card using another micro-SDHC compatible device (camera, another phone, card reader/writer etc).
3. Boot into recovery mode
4. Select Install from the TWRP menu and navigate to the zip file you download. Swipe the arrow key to confirm installation and wait for installation to be complete
5. When installation is complete, clear your cache and dalvik and reboot system and you are good to go.
Hope this works for you. If it does, please remember to hit the thanks button and let me know.
Larry2999 said:
You will find the full link here ...<http://forum.xda-developers.com/showthread.php?t=2658486>
Download Odin.
http://fortedge.com/downloads/Odin307.zip
Download the Odin flashable custom recovery file via the following link ...
<http://techerrata.com/browse/twrp2/d2att>. You need one of the more recent images ending in *.tar e.g. the one below
<http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.0-d2att.tar>
Install Samsung Kies on your PC if you don't have this already (this will be useful for the drivers)
Install the twrp tar file to an easily remembered location on your PC
Extract the Odin zip to get the executable file (*.exe)
Click on the exe file to run Odin
Now boot your phone into download mode by powering off completely then holding down the Power + Home + Volume Down buttons simultaneously until you see a warning message.
Press the Volume Up button to continue
Connect your phone to the computer with a good quality micro-USB cable
If everything has been done OK, Odin should immediately recognize your phone and you should see a message saying "Added" in Odin. If you don't see this, then you may need to check the drivers are properly installed.
Click on the PDA tab in Odin and navigate to the twrp tar file you earlier downloaded. Select this file and click OK.
You should have the Auto-Reboot and F-Reset Time boxes checked in Odin. Please do not check or uncheck any other boxes!
Click on the Start button at the bottom to start flashing TWRP and wait until you see PASS and a green (or blue) box fully displayed. Your phone will automatically reboot after this although it may not be able to boot since you don't have an OS installed. You may disconnect the cable and close Odin after you see the PASS message. If you see FAIL, then disconnect, remove the phone battery and try again.
If you successfully flash TWRP, then you may proceed to reinstalling your ROM.
1. Download the zip file in the thread below <<http://forum.xda-developers.com/showthread.php?t=2658486>>
2. Save to a recognizable location on your phone's SD card. If you can't install files to your phone via your PC, then you may save to a micro SDHC card using another micro-SDHC compatible device (camera, another phone, card reader/writer etc).
3. Boot into recovery mode
4. Select Install from the TWRP menu and navigate to the zip file you download. Swipe the arrow key to confirm installation and wait for installation to be complete
5. When installation is complete, clear your cache and dalvik and reboot system and you are good to go.
Hope this works for you. If it does, please remember to hit the thanks button and let me know.
Click to expand...
Click to collapse
Odin seems to stop working and crashes when i try to flash TWRP.
Ozzie 45 said:
Odin seems to stop working and crashes when i try to flash TWRP.
Click to expand...
Click to collapse
How far did you get and what was the <error> message you got?
---------- Post added at 10:10 PM ---------- Previous post was at 10:03 PM ----------
Larry2999 said:
How far did you get and what was the <error> message you got?
Click to expand...
Click to collapse
You may also try Odin 3 v1.85 if the v 3.07 didn't work. I've been looking for a safe download link for that online but I've not been able to find one. You may try searching for it online.
Larry2999 said:
How far did you get and what was the <error> message you got?
---------- Post added at 10:10 PM ---------- Previous post was at 10:03 PM ----------
You may also try Odin 3 v1.85 if the v 3.07 didn't work. I've been looking for a safe download link for that online but I've not been able to find one. You may try searching for it online.
Click to expand...
Click to collapse
Here is Odin 1.85
Or you could try putting a room on an SD card. That's why I always check to see if a room is there before flashing
Sent from my SGH-I747 using Tapatalk
Is there a way to switch from 5.0 to 4.4 while the phone is unrooted or would I have to root it in order for that to happen? Also if I have to root what would be the best way to do so and put back 4.4?
I am totally interested in this as well any step-by-step information would be highly appreciated
I would have to say no... you can flash back to 4.4... but need root to flash
Sent from my SM-N910P using Tapatalk
kaz007 said:
Is there a way to switch from 5.0 to 4.4 while the phone is unrooted or would I have to root it in order for that to happen? Also if I have to root what would be the best way to do so and put back 4.4?
Click to expand...
Click to collapse
Here's a step by step procedure to downgrade, make sure you backup your internal sd card contents because it requires a data/reset on 4.4. since lollipop encrypts internal storage.
Download these 3 files.
USB (Driver) ver.1.5.45.0 ( Latest as of this post ) from samsung.com/support, search for your device SM-N910P and choose your color, and select manuals and downloads
Odin v3.10.6, from rwilco12's website, HERE
N910PVPU1ANK2 .TAR file, from ViperBoy's thread in generals forum HERE
Save these files to your desktop within a folder called Note4Downgrade makes it easier to find.
Uninstall your previous drivers like old Samsung, Kies of any versions.
open the Odin zip file, drag and drop its contents into the Note4Downgrade folder.
Open the N910PVPU1ANK2 zip file, drag and drop the .tar file into the Note4Downgrade folder.
Install the latest Samsung drivers, no need to reboot your computer.
Open the Odin3.10.6 executable file, select PDA or AP slot and load in the NK2.tar file, it'll take awhile and the Odin program will freeze as the file that its loading is ~1.8 GB's.
In the mean time while this is being loaded, shutdown your Note 4 Device and go into download mode by pressing Volume Down, Home Button, and Power Button Simultaneously.
Hold it down until it starts up into an Android Logo Firmware screen, Next Press Volume Up to continue into the next dialogue.
Once the file is loaded into the Odin program, use the original Samsung USB cable and plug it into a USB 2.0 port ( No, Not 3.0, Sometimes it can cause issues and errors, its do-able, but not recommended. )
Have the Odin Program detect your device and Windows will install the device drivers. Once this is done, a word within a blue box will state this message up top.
[COM:##]
It does not matter on what the "##" is as long as that is reading a number, meaning Odin has recognized and detected your device.
Stop here and recheck your progress.
- Latest Samsung Drivers installed ( SM-N910P )
- Odin 3.10.6 with loaded N910PVPU1ANK2.tar inside the PDA or AP slot
- Device in download mode, plugged into a USB 2.0
- Odin with [COM:##] in a box.
Proceed to clicking the "START" button if you have all of your above progresses done.
This will take around 15-30 minutes of flashing the stock 4.4 firmware, this will not tick the KNOX switch if you haven't rooted your device already as this is stock firmware.
It'll auto reboot once it is done, First time boot up will take longer as it is loading the device for the "First Time".
Once you're done, and you're on the welcome screen of the device, power it off.
Now we need to do 2 sets of resets, data factory within recovery, and an internal SD card wipe through Backup and Reset menu within settings of the device.
Now go into the devices recovery by pressing these 3 buttons. Power UP, Home Button, and Power Button.
Hold it until you see blue text at the top left corner of your devices screen stating "REBOOTING RECOVERY. . . ."
Then you can let go.
LEGEND
- Volume buttons = up or down
- Power Button = Proceed into next dialogue
From here go into the wipe data/factory and reset the device.
Once done, do a cache wipe.
and lastly, reboot the device.
Once your device has been rebooted, skip all the welcome steps and go to home, pull down the notifications bar and select the setting button up top.
scroll down to storage and unmount your Ext SD Card and take it out ( If you have one! ), now back out and go within Back up and Reset under personalizations. checkbox wipe internal Card and factory data reset again.
Once its all done it'll reboot, now you're on the latest firmware of kitkat on the note 4.
I hope this will help you as well as others wanting to stay on kitkat for any reasons they have or if they run into issues on lollipop.
Your guide, simplified!
- Spark91
Awesommmme! Thanks for taking the time Spark!
Glad I've helped out!
Very thorough guide.
bought a note 4 (sm-n910p) from eBay thinking that i can use ssu.apk to sim unlock the device. It was on lollipop.
so i thought i can downgrade to 4.4 . unfortunately while flashing kitkat using odin i got a fail message .After that phone is showing ("firmware upgrade encountered an issue ")
i tried to flash stock lollipop firmware using odin sadly now it show { THERE IS NO PIT PARTITION } error .
the device is on oe1 build
I'm on N910PVPU3BOF5 will that work with my phone ?
zjor2000 said:
I'm on N910PVPU3BOF5 will that work with my phone ?
Click to expand...
Click to collapse
I think of5 has an updated bootloader and cannot be downgraded.
Hi,
Phone; SM-AF520F
My phone has been restarting on its own from the past month and I ignored it. It showed me occasionally Google services failed or system UI is not responding.
I factory resetted the phone as any noob would do and the restart occurrence went to only at night, which I was unbothered with. A little time passed and the phone went to the downloading sky blue screen.
I'm aware with flashing roms and stuff but I never really tried it. I tried everything;
i) Used Odin, three different versions
ii) Used Stock firmware, three different versions
iii) Used Smart switch
The phone only went in download phase and than in the phase where you press home button, volume and power and it shows fonts in the left hand corner. Odin always giving me errors, sometimes stucking on setting up connection.
Two errors:
i) There is no PIT partition
ii) Write operation failed
There are always these things happening.
When I restarted with volume down and power key, the system showed, there was an error and try smart switch, updated my drivers but when I go in the settings to emergency recover my phone, it does not show my phone.
After restarting the phone couple of time, Im in downloading mode again, in between the screen also turns full sky blue with no text.
I tried installing custom recovery but the image didn't load, ( I dont know what i am doing at this point, even if this was a good idea).
I have scavanged every forum, every post, everything on the internet but I just can't seem to fix it, I tried every possible thing and it just dosent work. I know it can be fixed but I don't know how. I know I'm doing something stupidly wrong but I can't seem to figure it out.
This is an old phone, I'm going to buy another one soon but I just hope it works for another week? Can I wipe the whole system and start from scratch (Which i dont know how to do).
Any type of help would be greatly appreciated, or just tell me to give up hope on it so I can just throw it away and move on.
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
matkali said:
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
Click to expand...
Click to collapse
Thank you for your response.
I did what you exactly said, previously it failed at the instant, now it moved one tab and than failed.
I tried the provided Odin, than tried two roms with, with the pit filed extracted and enabled re partition.
The error occurred: Complete(write) operation failed.
The error occurred every time I tried to flash, it never worked.
Do you think there is anything else to do?
Try this way to go download mode:
Press vol-down + power until phone restart
Then instantly press vol-up + Home + Power to going to download mode!
If it not works for you! You can use (eMMC programmer or easy JTAG) to writing rom on your phone memory (Last Option)!
I gave up on it and asked for professional help. Idk what he did, but he fixed the phone. It was sluggish at first but it works like a charm now.
It took 7 minutes to turn it on, than It said, there was an authorized user who tried to access your phone, use your previous email password to access your phone. I put it on my previous details and the works okay after some updates.
I wonder what he did? And i never knew android has a feature where if somone tries to reset your phone, google account locks it? Wow.
Is flashing a custom os a good idea? I'm afraid I'll brick it or something or just keep running one ui and wait for it to die again.
Thank you for your help btw, made me learn alot.
matkali said:
1-Install 7zip application in windows
Then using 7zip, try to open file (in stock ROM files) -⇾ "CSC_ODD_***"
2-There is your phone pit file for a520f.
Extract that file and keep it between your stock Rom files.
3-Download the Odin from this link and open it:
https://dl2018.sammobile.com/Odin3-v3.14.4.zip
4-Go to download mode (blue screen) in your phone!
Add 4 part of your ROM to Odin.
Then in pit tab of Odin add your phone pit file!
5-In option tab of Odin toggle Re-Partition option.
6-click on start and wait until it shows a green icon and phone restarting!
It must be fixed!
Click to expand...
Click to collapse
im having the exact same problem this guy has, installing a pit file will erase my data? if i use HOME_CSC will the pictures stay? i only care about the photos.