First things first, NEVER RESTORE A TWRP BACKUP YOU CREATED IN ONE VERSION IN ANOTHER VERSION.
Now coming to my situation, I installed the Deodexed Stable Zui Oreo ROM but as usual got bored with the zui and wanted to go back to my fav Pixel experience Rom so I clean flashed it from the unofficial hendibudi recovery but I couldn't use my internal storage and I once earlier read in another thread that installing 3.0.3 decrypts it so I installed that recovery and clean flashed AEX5.2 Rom this time and same internal storage problem continued so my lazy ass thought I'll restore the TWRP backup I created when I unlocked the bootloader instead of flashing through qfil and that was my mistake.
I created the backup on 3.1.0 but now I was on 3.0.3 so as soon as I restored the backup and rebooted, my phone didn't turn on, no zuk logo or led or anything, if I long press the power button it just vibrates and the led flashes for a sec, that's all.
Edit: feels like this thread belongs to the News/Discussions section than here but meh
Edit2: Solution in Post #4
It seems like qfil, mi flash method is last as your bootloader is also corrupted, and this happens because there are many critical hidden partition on our device so it mess up, when you install first twrp releases, you will notice there are 7 8 partition and in latest one they all are hidden.
narshi shukla said:
It seems like qfil, mi flash method is last as your bootloader is also corrupted, and this happens because there are many critical hidden partition on our device so it mess up, when you install first twrp releases, you will notice there are 7 8 partition and in latest one they all are hidden.
Click to expand...
Click to collapse
well if it's that easy I wouldn't be worried at all but unfortunately my situation is a bit different, I can't flash anything as my phone is recognized as 900E, to flash anything the phone should be recognized in 9008(edl) mode and for that I have to strip the cable and short circuit with it and all that, which is really a hit or miss kinda situation so kinda worried!
But seems like I have no other choice so let's see what happens, I tried stripping the stock usb cable and it got split into half lmao
now I'll buy another cable and will try the copper wire method instead of splitting it
Edit: yeah ik that different versions of TWRP are different but I wanted to restore only the data partition and my data was already encrypted so I thought I have nothing to lose, I was like if it doesn't work I'll flash the full firmware again but didn't expect it to fully brick the phone
Okay the primary reason for me creating this thread was to let y'all know how I bricked my device so that y'all won't repeat my mistake but I saw some people here and there recently asking how to resurrect their device so thought I'll share how I got mine working wishing it'll help such people.
My phone was completely dead, the hardware buttons weren't doing anything, the phone doesn't power off but all I could see was a black screen, so I had to follow THIS GUIDE.
But the above situation is a rarity, I guess most of you ppl could get to the zuk logo or your led keeps flashing and you can use your hardware buttons, in such situations, follow THIS GUIDE.
The above links are for you to get your phone to 9008 mode to be able to flash the stock firmware, but if you don't know how to flash,
refer THIS GUIDE.
Flashing problem
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
seetharam55555 said:
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
Click to expand...
Click to collapse
Only one solution is there.. after u get sahara error.. disconnect your phone and cable, then again turn your phone on. And then turn it off... After that press volume up+ power button simultaneously while connecting to the usb port, if you are successful, within 2-3 seconds you have to press the download button on QFIL.. then it should work... You can try 2-3 times... For demo, but thia is the only way out of this hard brick
.. i suffered in the sahara error for 3 days since i flashed OOS on my z2 , till today i finally got the solution
sidS6 said:
Only one solution is there.. after u get sahara error.. disconnect your phone and cable, then again turn your phone on. And then turn it off... After that press volume up+ power button simultaneously while connecting to the usb port, if you are successful, within 2-3 seconds you have to press the download button on QFIL.. then it should work... You can try 2-3 times... For demo, but thia is the only way out of this hard brick
.. i suffered in the sahara error for 3 days since i flashed OOS on my z2 , till today i finally got the solution
Click to expand...
Click to collapse
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
seetharam55555 said:
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
Click to expand...
Click to collapse
Not 2 minutes but i think 30 seconds at max.. and by successful i mean that you get into Qualcomm 9008 qdloader mode in qfil
---------- Post added at 05:13 PM ---------- Previous post was at 05:11 PM ----------
The main thing is you have to immediately press the download button(within 2-3 seconds) after reconnecting into 9008 mode
Briked my phone flasing oos, solved it in the first go usimg qpst method.
Rahil4321 said:
Briked my phone flasing oos, solved it in the first go usimg qpst method.
Click to expand...
Click to collapse
You didn't got Sahara error?
seetharam55555 said:
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
Click to expand...
Click to collapse
Were u able to unbrick?
Thanks
sidS6 said:
Were u able to unbrick?
Click to expand...
Click to collapse
yes it worked but as u said we have to hit download button within 2 sec....thank you very much u nearly saved 1000 rupees for me.
seetharam55555 said:
yes it worked but as u said we have to hit download button within 2 sec....thank you very much u nearly saved 1000 rupees for me.
Click to expand...
Click to collapse
Congrats bro! But i lost my 3 cables in ths process.. that equals 700 rs.. but i learned a great lesson? no probs
seetharam55555 said:
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
Click to expand...
Click to collapse
dude just cut the cable and make intersection betwwen vlack and gree wire and put the cable into phone , got edl mode simple ways
sidS6 said:
Congrats bro! But i lost my 3 cables in ths process.. that equals 700 rs.. but i learned a great lesson? no probs
Click to expand...
Click to collapse
Why did you wasted 3 cables for?
seetharam55555 said:
Why did you wasted 3 cables for?
Click to expand...
Click to collapse
Coz while spliiting, one got split into half ? and the other one got bent so it was unusable.. i had buy the third one
sidS6 said:
Coz while spliiting, one got split into half ? and the other one got bent so it was unusable.. i had buy the third one
Click to expand...
Click to collapse
Ohh you tried that method i did like this
sidS6 said:
You didn't got Sahara error?
Click to expand...
Click to collapse
You don't need to flash via qpst when you see logo but device wont boot it mean you locked your bootloader so all you need to do is unlock it again that's all
Nirmal0001 said:
You don't need to flash via qpst when you see logo but device wont boot it mean you locked your bootloader so all you need to do is unlock it again that's all
Click to expand...
Click to collapse
Unfortunately learnt this after unbricking my device
I had installed RR mix rom in my Zuk Z2 plus. while trying to enter fastboot mode, it went off. Now it is completely dead. not being recoganized in my PC.In device manager it is not shown. Tried to deep flash through Qfil, but didn't recoganize port.If i plug in charger also no LED indication, If I disconnect battery & plug in for charging, white LED slowly blinks, in the same mode if I connect charger blinking white LED continues. But once I remove charge & reconnect it shows nothing. again if I remove battery & reconnect, again white LED starts blinking. Apart from this nothing is shown, phone completely dead. Can anybody help please. I tried through Qfil, tried by shorting black & green cable, all types of key combinations.
Related
Hi,
I got one xiaomi redmi 1s rebooting, I hardest but not working
, so i decided to flash, via fastboot while flashing it stops in 14%.
now phone doesn't power on, while inserting usb, it detect as qualcomm usb in device manager comport.
Need help. how to revive.
riteshgpt60 said:
Hi,
I got one xiaomi redmi 1s rebooting, I hardest but not working
, so i decided to flash, via fastboot while flashing it stops in 14%.
now phone doesn't power on, while inserting usb, it detect as qualcomm usb in device manager comport.
Need help. how to revive.
Click to expand...
Click to collapse
Try Here
Read whole first, then give a try.
presetz said:
Try Here
Read whole first, then give a try.
Click to expand...
Click to collapse
Any one please share me tested solution with easy tutuorial.
riteshgpt60 said:
Any one please share me tested solution with easy tutuorial.
Click to expand...
Click to collapse
Have you read it? If its still not an easy way as it written, than might be someone can.
Sorry just tried to help.
Good luck sir.
presetz said:
Have you read it? If its still not an easy way as it written, than might be someone can.
Sorry just tried to help.
Good luck sir.
Click to expand...
Click to collapse
Hi, I finally flash with this file "armani_global_images_JHCMIBL50.0_4.3_in_111a6a27b4" and flashing process goes fine ,after flash it says to press f8 and I press OK buttom while holding f8 and PC restart, as software
Now phone shows little bip light in home button .
And now it doesn't shows qualcomm device as well, I think, boot is repair but fastboot mode not coming.
Need help.
riteshgpt60 said:
Hi, I finally flash with this file "armani_global_images_JHCMIBL50.0_4.3_in_111a6a27b4" and flashing process goes fine ,after flash it says to press f8 and I press OK buttom while holding f8 and PC restart, as software
Now phone shows little bip light in home button .
And now it doesn't shows qualcomm device as well, I think, boot is repair but fastboot mode not coming.
Need help.
Click to expand...
Click to collapse
Try previous version than 50, might be the 45 as it stable enough, i guess.
And before that, have you charged your phone? Mi recovery wont boot if under 20% battery.
presetz said:
Try previous version than 50, might be the 45 as it stable enough, i guess.
And before that, have you charged your phone? Mi recovery wont boot if under 20% battery.
Click to expand...
Click to collapse
Hi,
After flashing v50, the phone should be working, right?
Im downloading v45, but phone is not detecting with pc . no fastboot , no qualcomm usb , How can I flash now.
thank for guiding.
riteshgpt60 said:
Hi,
After flashing v50, the phone should be working, right?
Im downloading v45, but phone is not detecting with pc . no fastboot , no qualcomm usb , How can I flash now.
thank for guiding.
Click to expand...
Click to collapse
You said the led blinking a litte red light? Try to charged first till its more than 30% batt, and connect again. See if it show in pc
Thanks done after flashing v45
riteshgpt60 said:
Thanks done after flashing v45
Click to expand...
Click to collapse
Im glad to hear that, what an awesome experienced you got isnt it? At least you can learnt something from it
Hi, I tried to flash 20b through twrp tonight.
I did factory reset, then flashed the bootstack, then flashed the system. But after that, my phone won't power on. I tried to remove the battery, holding power button for a long time, or power+volumn down.
The phone just does not respond at all. Can anybody help? Thanks!
souvenir1977 said:
Hi, I tried to flash 20b through twrp tonight.
I did factory reset, then flashed the bootstack, then flashed the system. But after that, my phone won't power on. I tried to remove the battery, holding power button for a long time, or power+volumn down.
The phone just does not respond at all. Can anybody help? Thanks!
Click to expand...
Click to collapse
take the battery out and put it back in and try to power it on. Repeat a few times, if that doesn't help we'll try other things.
Still_living714 said:
take the battery out and put it back in and try to power it on. Repeat a few times, if that doesn't help we'll try other things.
Click to expand...
Click to collapse
Thank you Still_living714, I tried this multiple times, but it does not work. Anything else I can try?
souvenir1977 said:
Thank you Still_living714, I tried this multiple times, but it does not work. Anything else I can try?
Click to expand...
Click to collapse
have you tried putting it into download mode?
Still_living714 said:
have you tried putting it into download mode?
Click to expand...
Click to collapse
If you are talking about holding volume button up and plug into computer, I tried that and the phone does not respond either...
souvenir1977 said:
If you are talking about holding volume button up and plug into computer, I tried that and the phone does not respond either...
Click to expand...
Click to collapse
hmm very weird. I had a similar problem were the phone wouldn't boot unless I had it plugged into the charger or my computer,give that a try.
---------- Post added at 12:12 AM ---------- Previous post was at 12:10 AM ----------
souvenir1977 said:
If you are talking about holding volume button up and plug into computer, I tried that and the phone does not respond either...
Click to expand...
Click to collapse
when I had that problem I figured out that it was the battery that was making the phone act weird. Since LG sent me another battery when they had the promotion I used the other spare and that fixed it for me.
This happens right after I flashed the new system, I doubt it is the batter problem. If I plugged into the computer it still won't power on.
(If I remove the battery and plug into computer, the screen of the phone does show some symbol, probably regarding missing memory).
Let me try to see if I use kdz flash to reinstall the system. Thanks for the help.
souvenir1977 said:
This happens right after I flashed the new system, I doubt it is the batter problem. If I plugged into the computer it still won't power on.
(If I remove the battery and plug into computer, the screen of the phone does show some symbol, probably regarding missing memory).
Let me try to see if I use kdz flash to reinstall the system. Thanks for the help.
Click to expand...
Click to collapse
well it's hard to say but without the phone being able to boot there's not anything you can do.....
you are right, flashing need the download mode....
You're getting adnroidserial xxxx in device manager when you connect it to pc?
i think you bricked phone
jkjambo said:
You're getting adnroidserial xxxx in device manager when you connect it to pc?
i think you bricked phone
Click to expand...
Click to collapse
No it just shows regular LGE com port and I am not able to flash anything. You are right, it's hard bricked I am not sure what went wrong with my twrp flashing procedure though. Will contact with LG for repair.
souvenir1977 said:
No it just shows regular LGE com port and I am not able to flash anything. You are right, it's hard bricked I am not sure what went wrong with my twrp flashing procedure though. Will contact with LG for repair.
Click to expand...
Click to collapse
that's what i mean , lge serial xxx , don't remeber exactly . it's in qhsusb mode , hardbricked ...
there is some indian guys who do that , some for free, some for little amount of money ...
search for lg g3 unbrick Qhsusb 9008... don't waste time on tutorials , non of them works with D851 ... i'm in same boat (again ) and tried everything .. nothing works , unless you're connected to lg servers directly , search for people which fixs them
http://forum.xda-developers.com/lg-...1-d855-qhsusbbulk-t3101435/page2#post60751870
here you go.
this guy helped me for free , you can contact with him
Thanks! Currently my phone is at LG service since it is still in warranty. I will definitely try that next time (knock on wood...)
jkjambo said:
http://forum.xda-developers.com/lg-...1-d855-qhsusbbulk-t3101435/page2#post60751870
here you go.
this guy helped me for free , you can contact with him
Click to expand...
Click to collapse
souvenir1977 said:
Thanks! Currently my phone is at LG service since it is still in warranty. I will definitely try that next time (knock on wood...)
Click to expand...
Click to collapse
This is why You don't flash the boot chain unless you absolutely must. I was running 20B with the old boot chain (other than rpm, that was updated) and it ran just fine. If you get a bad flash on the boot chain your sol.
Hi all,
Need some help with my Zenfone 2 ZE551ML 4GB/32GB.
Decided to flash Nougat custom ROMs so followed these steps
Connected phone to PC and ran MM BL upgrade. It completed successfully.
Rebooted to BL, then rebooted to recovery, saw the new 3.0.2-M1 TWRP.
Went to TWRP and activated Sideload, ran ADB sideload command to load Nougat DU. It completed 100%.
Proceded to sideload gapps but connection failed. Maybe need to reactivate sideload in TWRP again.
Touched USB cable and the phone switched off. Ever since then it does not boot up and screen does not light up anymore.
Phone was on MM RR, BL unlocked. Battery was at 100% when performing the above actions.
Is there anything else (other than bringing it to ASUS) I can do to revive the phone?
Hi , I'm in a rush here , just one question to start ..
Can you get into bootloader via buttons not connected to charger ?
Do you know how to ?
Ps , you don't need to sideload roms in twrp , you just install them after usual wipes.
timbernot said:
Hi , I'm in a rush here , just one question to start ..
Can you get into bootloader via buttons not connected to charger ?
Do you know how to ?
Ps , you don't need to sideload roms in twrp , you just install them after usual wipes.
Click to expand...
Click to collapse
I can't. The way is to press the volume up and power buttons at the same time, and release the power button when the phone vibrates after a few seconds.
On my phone there was no response whatsoever.
Yeah I know I don't have to sideload ROMs, but I was lazy to copy it to the SD card.
Plus I had plans to wipe the internal SD card, so didn't copy there either...
s79336951 said:
I can't. The way is to press the volume up and power buttons at the same time, and release the power button when the phone vibrates after a few seconds.
On my phone there was no response whatsoever.
Yeah I know I don't have to sideload ROMs, but I was lazy to copy it to the SD card.
Plus I had plans to wipe the internal SD card, so didn't copy there either...
Click to expand...
Click to collapse
Sounds like you are bricked my friend
but do try holding power button and vol for a good length of time...then power button too on its own for some time..
If and when you get two vibes , if no boot loader
Check unbrick threads .
If get bootloader , scroll to recovery select it .
Next time download roms to fone
safer !
I think kernel is in panic mode. Try disconnecting the battery for a little while and then reconnect it. You'll have to open your phone to do it. There are many YouTube videos to see how you can do so. It's not that difficult. Good luck!
I'm in the same boat... no even LED while connected to the charger... Already disconnected the battery and closed again. No joy. Is this a "deep brick of death"?? Its too expensive to give away without fight a little. Any help is more than welcome
There are threads on xda that describe how to revive hard bricks.
For me, disconnecting and reconnecting the battery had worked.
Please make sure that battery is connected perfectly.
Sometimes , leaving on charge brings at least the two vibes back eventually
That's enough to start xFSTK unbricking process.
Besides the already mentioned battery disconnect.
I seen one guy revive by disconnecting USB board too
timbernot said:
Sounds like you are bricked my friend
but do try holding power button and vol for a good length of time...then power button too on its own for some time..
If and when you get two vibes , if no boot loader
Check unbrick threads .
If get bootloader , scroll to recovery select it .
Next time download roms to fone
safer !
Click to expand...
Click to collapse
Looking at unbricking threads.
Problem is the PC was unable to detect the phone in IntelSOC mode. Absolutely no response.
I will try different OS and machines though
uhm said:
I think kernel is in panic mode. Try disconnecting the battery for a little while and then reconnect it. You'll have to open your phone to do it. There are many YouTube videos to see how you can do so. It's not that difficult. Good luck!
Click to expand...
Click to collapse
Thanks! will try this too
timbernot said:
Sometimes , leaving on charge brings at least the two vibes back eventually
That's enough to start xFSTK unbricking process.
Besides the already mentioned battery disconnect.
I seen one guy revive by disconnecting USB board too
Click to expand...
Click to collapse
You mean leave it connected to PC to charge until the two vibes came back?
I originally did have the two vibes, but the phone was connected to the charger at that point.
Unfortunately I don't have the vibes even connecting to the same charger now.
I believe the solution now is to try to recover the bootloader and restore the OS.
Question is how to get it detected in PC in IntelSOC mode.
Things to try:
Disconnect battery
Disconnect USB board
Try different PCs and OS
wiltgen said:
I'm in the same boat... no even LED while connected to the charger... Already disconnected the battery and closed again. No joy. Is this a "deep brick of death"?? Its too expensive to give away without fight a little. Any help is more than welcome
Click to expand...
Click to collapse
I'm sorry to hear that. I will try to disconnect the battery to see if I have more luck.
It was also mentioned that disconnecting the USB board worked for one guy.
s79336951 said:
Looking at unbricking threads.
Problem is the PC was unable to detect the phone in IntelSOC mode. Absolutely no response.
I will try different OS and machines though
Thanks! will try this too
You mean leave it connected to PC to charge until the two vibes came back?
I originally did have the two vibes, but the phone was connected to the charger at that point.
Unfortunately I don't have the vibes even connecting to the same charger now.
I believe the solution now is to try to recover the bootloader and restore the OS.
Question is how to get it detected in PC in IntelSOC mode.
Things to try:
Disconnect battery
Disconnect USB board
Try different PCs and OS
Click to expand...
Click to collapse
When you get two vibes back , you can install isoc driver and your PC will recognise it.
In the early days before unbricking knowledge of zen 2 , I also witnessed the same , blank screen no vibes
What I did was leave it on charge , every hour or so ..press power plus vol plus , quick press , then after a longer press , if nothing then just power , quick press and a longer press.
Then I awoke to the vibes
Once the vibes start , then its install isoc , don't install xFSTK downloader until driver is set up
PS , that was before we found discon of battery method and still had warranty
timbernot said:
When you get two vibes back , you can install isoc driver and your PC will recognise it.
In the early days before unbricking knowledge of zen 2 , I also witnessed the same , blank screen no vibes
What I did was leave it on charge , every hour or so ..press power plus vol plus , quick press , then after a longer press , if nothing then just power , quick press and a longer press.
Then I awoke to the vibes
Once the vibes start , then its install isoc , don't install xFSTK downloader until driver is set up
PS , that was before we found discon of battery method and still had warranty
Click to expand...
Click to collapse
Can I ask how many times you tried before getting the two vibes back?
And it was connected to the PC's USB port?
I asked because I did have the vibes when connecting to the wall charger.
But it went away when I then connect to the PC. And now there are no vibes even when connecting to wall charger.
s79336951 said:
I believe the solution now is to try to recover the bootloader and restore the OS.
Question is how to get it detected in PC in IntelSOC mode.
Things to try:
Disconnect battery
Disconnect USB board
Try different PCs and OS
Click to expand...
Click to collapse
Tried disconnecting battery and USB board.
Unfortunately it didn't work.
Will try leaving it disconnected for an hour.
s79336951 said:
Tried disconnecting battery and USB board.
Unfortunately it didn't work.
Will try leaving it disconnected for an hour.
Click to expand...
Click to collapse
After one hour of disconnected battery and USB board and still the same.
Trying to connect to PC's USB and pressing the power buttons every hour or so now.
s79336951 said:
After one hour of disconnected battery and USB board and still the same.
Trying to connect to PC's USB and pressing the power buttons every hour or so now.
Click to expand...
Click to collapse
Leave on charge , means exactly that, leave on charger .
Leave it on a full day , if fone gets warm its charging .
Try all the stuff already mentioned.
Some people have give up , thrown fones in draw and 3 months later come back to life.
Some people hot wired battery straight to charger too, but that's off limits .
There is nothing straight forward that works for everyone , here is a few exanples of what revived many fones ,you pay the price for being lazy
We all learn the hard way
Hi guys, I had my bootloader lost so i followed this guide https://forum.xda-developers.com/zenfone2/general/guide-brick-soft-hard-bricked-zenfone-2-t3284256 and it worked like a charm except for flashing OS part, on fastboot it said 'Result: Okay' but in AFT it said 'That interface is already detected in UI, please delete it and reconnect device' so I did it and still the same so since the result was okay in fastboot I wanted to try get into recovery hoping it'll start-up and just when I pressed 'vol up' button it didn't even change the choice in fastboot, screen just faded out and phone isn't even charging now, adb doesn't see it, fastboot isn't booting up, no vibration, PowerBank is detecting the device and is power draining -> phone even is heating a little like it is charging but no screen/led :crying: Help me guys, pls
Ozzy0997 said:
Hi guys, I had my bootloader lost so i followed this guide https://forum.xda-developers.com/zenfone2/general/guide-brick-soft-hard-bricked-zenfone-2-t3284256 and it worked like a charm except for flashing OS part, on fastboot it said 'Result: Okay' but in AFT it said 'That interface is already detected in UI, please delete it and reconnect device' so I did it and still the same so since the result was okay in fastboot I wanted to try get into recovery hoping it'll start-up and just when I pressed 'vol up' button it didn't even change the choice in fastboot, screen just faded out and phone isn't even charging now, adb doesn't see it, fastboot isn't booting up, no vibration, PowerBank is detecting the device and is power draining -> phone even is heating a little like it is charging but no screen/led :crying: Help me guys, pls
Click to expand...
Click to collapse
Have you sorted this ?
If not, check my unbrick vid in my signature
timbernot said:
Have you sorted this ?
If not, check my unbrick vid in my signature
Click to expand...
Click to collapse
Yeah, I did everything but in the part where you flash system I got message "Device already exists in UI, please delete and reconnect device", I did it but result was still the same, pressed volume up button to check if recovery is there and the screen just like 'faded out' and now isn't even responding, isn't seen by xfstk and stuff ;-;
Ozzy0997 said:
Yeah, I did everything but in the part where you flash system I got message "Device already exists in UI, please delete and reconnect device", I did it but result was still the same, pressed volume up button to check if recovery is there and the screen just like 'faded out' and now isn't even responding, isn't seen by xfstk and stuff ;-;
Click to expand...
Click to collapse
Do you hold down volume down key when connecting to PC via USB ?
Hnk1 said:
Do you hold down volume down key when connecting to PC via USB ?
Click to expand...
Click to collapse
it's obvious ;-;
Ozzy0997 said:
it's obvious ;-;
Click to expand...
Click to collapse
You are now bricked.
What you need to do is get the 2 vibes back at least , then your device will be seen for xFSTK downloader to re flash again.
Try charge overnight from wall charger.
Press power for a good length of time and restart the flash if you get the 2 vibes back.
Watch the video closely in the first 7 mins, I suspect you had normal bootloader tho.
Temp ifwi version after flash is 0094 0169 .
What was yours ?
timbernot said:
You are now bricked.
What you need to do is get the 2 vibes back at least , then your device will be seen for xFSTK downloader to re flash again.
Try charge overnight from wall charger.
Press power for a good length of time and restart the flash if you get the 2 vibes back.
Watch the video closely in the first 7 mins, I suspect you had normal bootloader tho.
Temp ifwi version after flash is 0094 0169 .
What was yours ?
Click to expand...
Click to collapse
I got the same ifwi, hope that 2 vibes will get back :fingers-crossed:
Ozzy0997 said:
I got the same ifwi, hope that 2 vibes will get back :fingers-crossed:
Click to expand...
Click to collapse
Reason i suspect you got normal bootloader is because after success of OS you get four colours before bootloader , which you dont mention and i have witnessed flashing ifwi and fwr dnx and it booting into bootloader without success of OS , that bootloader version was not the temp one needed to flash raw or atleast the OS partitions correctly ready for raw. Point being , i thought i was bricked but wasnt , just a temp death blank screen situation and then getting success in ifwi and fwr corrupted the device further , so a full re flash in xFSTK and success fixed it.
Getting the two vibes back is a bit hit n miss , nothing straight forward -- battery gets hammered flashing in xFSTK and usb charging isnt enough plus the fact your device might be on, yet shows no signs although it will be recycling itself till death without the juice to vibrate .
pressing power for a good length of time after a good charge , you might get one vibe depending on the state of off or on while on charge, i have had the vibes kick in halfway thru the night.
Some people have disconnected battery and reconnected to get success in xFSTK
good luck :good:
After a like 7-8h of charging it still doesn't vibrate even once
You want to let it charge for a full day without touching it
Sent from my ASUS_Z00AD using Tapatalk
Ozzy0997 said:
After a like 7-8h of charging it still doesn't vibrate even once
Click to expand...
Click to collapse
buddy you have to take out your battery and then charge it externally
Ozzy0997 said:
After a like 7-8h of charging it still doesn't vibrate even once
Click to expand...
Click to collapse
If device warmed up while on charge , then it will be charging , maybe disconnect battery and reconnect trying xFSTK.
If not warming then it's a hard wire charge like mentioned .
Well, it's working now, I had to reconnect battery and it came out that OS has been flashed but battery had an error, after reconnect it booted up like nothing happened, thanks to all of you for help
Hi all,
Yesterday I've reinstalled the stock rom via Oppo-Realme OFP flash, and it seemed like everything was working fine. Right after the flash had finished, I've relocked the bootloader to bring the phone to stock conditions again. Ever since, all I get is a really fast reboot, the white Realme logo shows up for less than a second and then it reboots. I can't even turn it off, volume up or down with power button combinations don't seem to work at all. I've only managed to stop it from bootlooping by pressing volume up and down simultaneously, but it reboots anyway after 15 seconds or so. What can I do here? Should I just RMA it or is there something else I haven't tried that could work? Thanks in advance
You can try remove the back cover of the phone and disconnect the battery and connect it again, after this try to push on the two volume buttons and connect it to the pc , and look over the driver manager if it on edl mode
eliran0216 said:
You can try remove the back cover of the phone and disconnect the battery and connect it again, after this try to push on the two volume buttons and connect it to the pc , and look over the driver manager if it on edl mode
Click to expand...
Click to collapse
Thanks, I'll try to do that. What do I do afterwards?
Look on this video carefully and do exactly same the guide, it mandatory to do backup on qfil app before do the flashing
eliran0216 said:
Look on this video carefully and do exactly same the guide, it mandatory to do backup on qfil app before do the flashing
Click to expand...
Click to collapse
This is amazing, I'll try it asap
eliran0216 said:
Look on this video carefully and do exactly same the guide, it mandatory to do backup on qfil app before do the flashing
Click to expand...
Click to collapse
I can't express how much I'm grateful, both to you and the youtuber. I got it back working! Thank you!
I am happy that this help you to unbrick your phone