Related
Hi!
I want to install [ROM][7.1] RESURRECTION REMIX N [5.8.0][BJRR][OxygenCam] 29.11.16.
I understand how to go to bootload, recovery, use adb, fastboot etc.
I just lack of some practice.
My question is, in which order install/flash everything?
It's written
INSTALLATION INSTRUCTIONS
- Download the latest build
- Download Gapps
- Take a nandroid backup
- Recommended - Full wipe and factory reset
- Flash ROM using latest Recovery
- Flash Gapps
- Reboot.
- Enjoy!
Installation Files
1.) Required twrp
2) Required Firmware & Modem 3.5.5-CE
3.) rom
4.) Open Gapps
Click to expand...
Click to collapse
I don't know which firmware/modem I'm using since I installed TWRP, OxygenOS Open Beta 8 (Nougat), then messed up and returned to 3.2.6 with original recovery etc.
I'll unlock the bootloader again, install TWRP in order to flash the ROM, Gapps and firmware/modem (just in case I guess).
But, at which step I should flash firmware/modem? After flashing rom and before gapps or at some other point?
Thanks a lot for your help!
(Oh, and I sure hope I'm in the right section of the forum!)
I installed OmniRom but i have encryption unsuccesfull. Help Please
Seems like issue is with storage. From what i know omni works only with unified lvm partition. To do this i flash coloros and unify partition there. Then install custom recovery and after that flash omni.
Sent from my Redmi Note 3 using Tapatalk
I am also facing same problem after flashing Omni ROM 'nougat' on my find 7s but no problem with marshmallo
Try this. Flash coloros recovery and flash coloros. Boot into coloros and then unify partition in coloros. Then flash latest twrp. Boot into recovery (twrp now) and flash omni rom. I have omni rom nougat (7.1.2) working on my find7a flawlessly since quite some time.
Sent from my Redmi Note 3 using Tapatalk
If you have Chinese unified storage, you need to flash Tha latest patch zip after flashing Omni.
I appear to have this problem too, every time I flash Omnirom. I was able to install LineageOS without any issues, but they don't support LVM.
I've tried a few sequences, but my latest is:
Installed ColorOS 2.1.5i
Setup Unified Storage
Root with Kingo Root
Unlock bootloader
Install TWRP
Factory Reset
Flash Omnirom 7
Flash GAPPS
Then stuck on encryption unsuccessful every time.
U just flash spectrum rom and remove lvm
PaulHaydockUK said:
I appear to have this problem too, every time I flash Omnirom. I was able to install LineageOS without any issues, but they don't support LVM.
I've tried a few sequences, but my latest is:
Installed ColorOS 2.1.5i
Setup Unified Storage
Root with Kingo Root
Unlock bootloader
Install TWRP
Factory Reset
Flash Omnirom 7
Flash GAPPS
Then stuck on encryption unsuccessful every time.
Click to expand...
Click to collapse
How did u set up unified storage? Did u use the option in coloros? Omni only supports lvm and works for me without issues.
Sent from my DUK-L09 using Tapatalk
LVM
Yeah, can someone tell me how to run unified storage in color os?
Flash this zip, you will fully wipe your phones storage after that you have to reboot the recovery and install omnirom and Gapps
https://androidfilehost.com/?fid=24052804347800902 LVM zip
The wipe is not necessary?
DroidSK said:
Seems like issue is with storage. From what i know omni works only with unified lvm partition. To do this i flash coloros and unify partition there. Then install custom recovery and after that flash omni.
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
do not we have to do wipes? do we flash dirty?
Hazelito said:
do not we have to do wipes? do we flash dirty?
Click to expand...
Click to collapse
Follow my steps:
1. first install LVM zip
2. Install omnirom and Gapps
3. Place everything on your SD card, without SD card it won't work
4. Go into TWRP
5. Wipe everything but the external SD card
6. Flash LVM zip
7. Reboot recovery
8. Install omnirom and Gapps (first omnirom)
9. Reboot
LVM zip: https://androidfilehost.com/?fid=24052804347800902
I'm not responsible for any damage to your device of any sort.
By flashing this you take responsibility of anything that happens.
Process at your own risk!
This recovery was developed for the p905. It doesn't apply to the p905v at this time because it's bootloader locked and a custom recovery isn't possible.
Instructions
Install zip using an existing custom recovery
Work
Everything works as in the original version + otg and mtp.
Links
2. 20180708: 3.2.2-0 version:
from recovery: https://drive.google.com/file/d/1v5KlNFjaQqpyml7TotbleIvsGhITyYFk/view?usp=sharing
from odin: https://drive.google.com/file/d/1RMqFJ7uXVwttxu5dmYarQLcAi56g2seh/view?usp=sharing
1. 20171006: 3.1.1-0: https://drive.google.com/file/d/0B-6nm7Jks0W5MHlwTUxlUDFiOWc/view?usp=sharing
Sources
TWRP: https://github.com/minimal-manifest-twrp/platform_manifest_twrp_omni
Device: twrp branch: https://github.com/Valera1978/android_device_samsung_viennalte
i m on official twrp and i m not able to install magisk (image cant get compressed to size of 10mb boot, always 10.4)
will this inofficial twrp build help to get magisk installed
Valera1978 said:
I'm not responsible for any damage to your device of any sort.
By flashing this you take responsibility of anything that happens.
Process at your own risk!
This frecovery was developed for the p905. It doesn't apply to the p905v at this time because it's bootloader locked and a custom recovery isn't possible.
Instructions
Install zip using an existing custom recovery
Work
Everything works as in the original version + otg and mtp.
Links
1. 20171006: 3.1.1-0: https://drive.google.com/file/d/0B-6nm7Jks0W5MHlwTUxlUDFiOWc/view?usp=sharing
Sources
TWRP: https://github.com/omnirom/android_bootable_recovery
Kernel: https://github.com/Valera1978/android_kernel_samsung_lt03lte
Click to expand...
Click to collapse
For some reason this recovery causes facebook and facebook messenger apps to continuously crash over and over, other than that so far everything is great!
@Valera1978
Amazing! Thanks for sharing with us!
@Valera1978
Sooooooo cool! :good:
....and.....while not using F*ckbook, I don't care about crashing messengers and so on. :evel:
I installed this recovery and everything is ok except when trying to restore modem
I backed up my system to install official firmware to test some stuff
Then i reinstalled the recovery and tried to restore my backup but it was failing when restoring the modem
I deselected the modem and restored everything else and all ok
Same here. Failing restoring the modem.
The latest official Version doesn't work either (crash):
twrp-3.2.1-0-viennaltexx
The latest working version for my p905 is:
twrp-3.0.2-0-viennaltexx
https://twrp.me/samsung/samsunggalaxynotepro122qcom.html
i flashed twrp recovery sucessfully thru odin..but when i tried to boot to recovery it's still stock firmware recovery not twrp recovery please help
The bootloader is unlooked?
Could you start into the bootloader?
If yes, you can flash the recovery via fastboot
after five times I have managed
My big problem now is how do I activate HDMi?
have a MHL cable micro usb to HDMi when I plug it in nothing happens
Thanks a lot for this TWRP 3.2.2-0 it works nice with SM-P905, and Valera1978 Android 9 Pie ROM.
Easy install, Valera1978 TWRP 3.2.2-0 img from Official TWRP 3.0.2-0 viennalte.
Format f2fs, And latest magisk
risant said:
i flashed twrp recovery sucessfully thru odin..but when i tried to boot to recovery it's still stock firmware recovery not twrp recovery please help
Click to expand...
Click to collapse
Successfully TWRP flash thru Odin, observe the progress in Odin left bottom corner and prepare for this; "directly" when flash finished "force recovery start" (volume up home and startbutton until recovery starts)
Not fast enough" stock recovery autorestore ! Doitagain.
About bootloader (4.4.2 KK)
Hi,
I've just got a SM-P905 on 4.4.2 kitkat (stock). I'd like to flash one of your ROM (probably the LOS 17.1) and this recovery first.
Should I just flash it through Odin or do I need to unlock the bootloader? In that case, could you please drive me to a tutorial? I've searched a lot on this forum on howto unlock the SM-P905 bootloader (or just if it comes -the 4.4.2 version at least- with an unlocked one already) but I haven't found anything on it.
Thanks in advance
SYS2048 said:
Hi,
Should I just flash it through Odin or do I need to unlock the bootloader?
Click to expand...
Click to collapse
Flash TWRP only, through Odin.
Then flash ROM, GApps, and optional Magisk, through TWRP.
Magisk needed for root-apps, or to hide root.
(flash bootloader and modem not needed, only sometime later, if your modem are to old, and SIM not working)
KjellO said:
Flash TWRP only, through Odin.
Then flash ROM, GApps, and optional Magisk, through TWRP.
Magisk needed for root-apps, or to hide root.
(flash bootloader and modem not needed, only sometime later, if your modem are to old, and SIM not working)
Click to expand...
Click to collapse
Done a couple of days after my post. Forgot to report. Then flashed LOS 17, gapps (pico) and Magisk. Everything's ok.
Thanks for your answer.
Anyway, now it can be said that the P905 with stock 4.4.2 KK has the bootloader unlocked.
Hi, I've downloaded twrp-3.2.2.0-viennaltexx.img.tar and flashed by Odin, but twrp doesn't installed. In Developer settings I have not OEM unlock option.
what can I do?
uzzi78 said:
Hi, I've downloaded twrp-3.2.2.0-viennaltexx.img.tar and flashed by Odin, but twrp doesn't installed. In Developer settings I have not OEM unlock option.
what can I do?
Click to expand...
Click to collapse
What is your actual stock firmware on it?
You can try latest official .tar and then work your way up to this.
bmwdroid said:
What is your actual stock firmware on it?
You can try latest official .tar and then work your way up to this.
Click to expand...
Click to collapse
Now I've Android 5.0.2
LRX22G.P905XXSABQB1
@uzzi78 so you have the latest bootloader installed.
That's good.
Btw afaik/remember there is no unlock option.
Try other TWRPs as a. m.
Hello,
i have version 11.0.2.0 Global on the device with twrp, magisk and edXposed.
Now I have seen that there is already a global version 11.0.6.0.
In my case, how can I update to a new version without losing the data and settings?
And one more question in general. Version 11.0.6.0 is not shown to me via OTA. Here it says, latest stable version 11.0.2.0. Is it not rolled out via OTA?
And if there was a newer version available via OTA, could I install the update despite TWRP?
hmarder said:
Hello,
i have version 11.0.2.0 Global on the device with twrp, magisk and edXposed.
Now I have seen that there is already a global version 11.0.6.0.
In my case, how can I update to a new version without losing the data and settings?
And one more question in general. Version 11.0.6.0 is not shown to me via OTA. Here it says, latest stable version 11.0.2.0. Is it not rolled out via OTA?
And if there was a newer version available via OTA, could I install the update despite TWRP?
Click to expand...
Click to collapse
I (without root) flashed the OTA on 11.0.2.0 global PGGMIXM to 11.0.6.0, but, to flash with root... Maybe (I dont know if it will brick) but you can try flash a recovery version of 11.0.6.0
hmarder said:
Hello,
i have version 11.0.2.0 Global on the device with twrp, magisk and edXposed.
Now I have seen that there is already a global version 11.0.6.0.
In my case, how can I update to a new version without losing the data and settings?
And one more question in general. Version 11.0.6.0 is not shown to me via OTA. Here it says, latest stable version 11.0.2.0. Is it not rolled out via OTA?
And if there was a newer version available via OTA, could I install the update despite TWRP?
Click to expand...
Click to collapse
I had exactly the same setup as you - here's what I did: 1 - Downloaded full rom from official Mi website (MIUI Global 11.0.6.0(PGGMIXM) 2 - Moved rom to root storage 3 - Flashed rom with TWRP, and voila! Updated to latest stable rom. Just remember to flash TWRP recovery again through Fastboot, because you will have stock recovery after update. I am using LTWRP- 3.3.1 -0924 and rooted and installed Magisk, without issues
hmarder said:
Hello,
i have version 11.0.2.0 Global on the device with twrp, magisk and edXposed.
Now I have seen that there is already a global version 11.0.6.0.
In my case, how can I update to a new version without losing the data and settings?
And one more question in general. Version 11.0.6.0 is not shown to me via OTA. Here it says, latest stable version 11.0.2.0. Is it not rolled out via OTA?
And if there was a newer version available via OTA, could I install the update despite TWRP?
Click to expand...
Click to collapse
One thing you forgot to mention is what region is your phone (not your Rom). If Chinese you may have to be extra cautious and steps above might not work for you.
Good luck!
KonahZave said:
I (without root) flashed the OTA on 11.0.2.0 global PGGMIXM to 11.0.6.0, but, to flash with root... Maybe (I dont know if it will brick) but you can try flash a recovery version of 11.0.6.0
Click to expand...
Click to collapse
Interesting. I'm still on rooted miui 10 4.5.0 PGGEUXM rooted magisk and twrp recovery-红米Note8Pro-3.3.1-9.0.img
I didn't update yet as bricking started to happen and I can't miss my phone as a daily driver.
Normally I would flash the full ROM, flash magisk, wipe cache and reboot.
So flashing full ROM doesn't break root?
Can't we flash recovery by twrp after flashing ROM instead by flashing by fastboot?
Isnt secure flash twrp after the ROM.
donkyshot said:
So flashing full ROM doesn't break root?
Can't we flash recovery by twrp after flashing ROM instead by flashing by fastboot?
Click to expand...
Click to collapse
Flashing a full rom will break root, and install stock recovery...
It is too risky to flash another recovery with twrp (possible brick)
so where to put official update on sd card?
download recovery rom?
unoturbo1 said:
I had exactly the same setup as you - here's what I did: 1 - Downloaded full rom from official Mi website (MIUI Global 11.0.6.0(PGGMIXM) 2 - Moved rom to root storage 3 - Flashed rom with TWRP, and voila! Updated to latest stable rom. Just remember to flash TWRP recovery again through Fastboot, because you will have stock recovery after update. I am using LTWRP- 3.3.1 -0924 and rooted and installed Magisk, without issues
Click to expand...
Click to collapse
I just brought rmn8p with miui 11.0.6.0 ,so it is ok to use LRTWRP-3.3.1 -0924. I came across a new version -1104, I'll try it after unlock the bootloader. After that flash preloader then trwp.
Use LR.TWRP, it got an option to make the TWRP persist on every OTA.
Also LR.TWRP = less headache on Xiaomi devices.
Here's the latest build: https://mega.nz/folder/cMAT3Q4b#7CbPV7sbEuSEdP7cehXJ-w
tze_vitamin said:
so where to put official update on sd card?
download recovery rom?
Click to expand...
Click to collapse
??
Put on external sd card dude
unoturbo1 said:
I had exactly the same setup as you - here's what I did: 1 - Downloaded full rom from official Mi website (MIUI Global 11.0.6.0(PGGMIXM) 2 - Moved rom to root storage 3 - Flashed rom with TWRP, and voila! Updated to latest stable rom. Just remember to flash TWRP recovery again through Fastboot, because you will have stock recovery after update. I am using LTWRP- 3.3.1 -0924 and rooted and installed Magisk, without issues
Click to expand...
Click to collapse
For chinese, this will brick the phone. See this instead.
Guys I Just see This video and in it shows the update process, with ltwrp, when the recovery capture the process and update even without losing data, its This True?, somebody has tried?
Link.
This will brick every phone. I brick my EU ROM, with this method of update rooted phone.
What is correct solution to update rooted phone?
Redmi Note 8 Pro, 11.0.2 QGGEUXM, TWRP 3.3.1 1210, Magisk 20.3 -> 12.0.1 QGGEUXM
System say there exists update, i choose download, select reboot, but after reboot i end up in TWRP but nothing happened. After exit i boot to old 11.0.2 system with message that update fail.
Edit 1: after 2. download/update/reboot TWRP start installing image ...
Edit 2: after automatic update system say 12.0.1, just loosing root (all apps stay)
Edit 3: installed TWRP again, Magisk (there was little problem because Magisk Manager say "not installed", but after some googlig i fix that. So i update system without reinstalling apps or loosing data.
Clear solution is probably download full rom from official Mi website and flash selected rom with TWRP (flash TWRP recovery again, repeat root process, to get root back). See next post.
RedMu said:
So what is correct solution to update rooted phone?
Redmi Note 8 Pro, 11.0.2 QGGEUXM, TWRP 1210, Magicks 20.3 -> 12.0.1 QGGEUXM
Now system say there exists update, i choose download, select reboot, but after reboot i end up in TWRP. After exit i boot to old 11.0.2 system with message that update fail.
So solution is probably downloaded full rom from official Mi website and flash selected rom with TWRP (flash TWRP recovery again, repeat root process, to get root back).
So what is correct way for update in this case?
Click to expand...
Click to collapse
This is how I upgraded, try at your own risk.
Download full recovery zip of MIUI 12 and latest magisk
Create twrp Backup just in case
In LR TWRP 10 mount & format system, cache, dalvik, vendor.
Flash full rom (not ota!)
Press home to return to the main screen Choose Advanced-File Manager item >system_root / system / folder at the bottom if there is a recovery_fromboot.p file delete it.
Go back to Advanced and select Close AVB2.0 and confirm with a swipe to the right.
flash Magisk
boot to system
First boot takes a while, relax and grab a drink
Remember to backup and close AVB!
Thank you so much for sharing these steps. I have questions for a couple of steps below:
donkyshot said:
This is how I upgraded, try at your own risk.
Download full recovery zip of MIUI 12 and latest magisk
Create twrp Backup just in case
In LR TWRP 10 mount & format system, cache, dalvik, vendor.
Click to expand...
Click to collapse
What is TWRP 10? Do I format first and then mount? I usually wipe system, cache, dalvik and then "install" the full rom (your next step), but i never try "mount" here. What does mount do here? what is wiping vender and mounting vender?
donkyshot said:
[*]Flash full rom (not ota!)
[*]Press home to return to the main screen Choose Advanced-File Manager item >system_root / system / folder at the bottom if there is a recovery_fromboot.p file delete it.
[*]Go back to Advanced and select Close AVB2.0 and confirm with a swipe to the right.
Click to expand...
Click to collapse
There are two check box here. one is "close the boot verification of avb2.0" the other is "close the DMVerity of avb2.0". Do O check one of both?
Thank you!
po1 said:
Thank you so much for sharing these steps. I have questions for a couple of steps below:
What is TWRP 10? Do I format first and then mount? I usually wipe system, cache, dalvik and then "install" the full rom (your next step), but i never try "mount" here. What does mount do here? what is wiping vender and mounting vender?
There are two check box here. one is "close the boot verification of avb2.0" the other is "close the DMVerity of avb2.0". Do O check one of both?
Thank you!
Click to expand...
Click to collapse
Recovery LR TWRP for Android 10
https://androidfilehost.com/?fid=8889791610682889486
First mount system, cache, dalvik, vendor
Than format system, cache, dalvik, vendor
Without mounting folders they won't be mounted
►go back to your main screen: ADVANCED- close AVB 2.0 then swipe to confirm, just tick only 1st box, ignore the second box
Introduction
This is a LineageOS Recovery compiled from the source tree of LineageOS 17.1 for Redmi Note 9S / 9 Pro.[/STRIKE] While the recovery has been usable for quite some time now, since it is not possible for TWRP to support any device launched with Android 10 for now.
I am aware that there is a TWRP port for this device, but since the source code is not accessible (as for as I can tell, maybe I just did not look hard enough for the source code), I can only advice against using it. The official TWRP open-sourced under GPLv3 does not even support devices launched with Android 10 yet, so there's clearly something going on here. I do not fix compatibility issues between my ROM and that TWRP port.
Instructions (Installing Recovery)
1. Download recovery-XXXX.zip (extract to get recovery.img and vbmeta.img)
2. Reboot to bootloader (`adb reboot bootloader`)
3. Run `fastboot --disable-verification --disable-verity flash vbmeta vbmeta.img`
4. Run `fastboot flash recovery recovery.img`
5. Run `fastboot reboot recovery` to enter LineageOS Recovery
Instructions (Installing Magisk)
You have to use the official Magisk, version 20.4 or later. Installing an older Magisk will make the system unbootable.
1. Download Magisk >= 20.4, put onto computer
2. Reboot to LineageOS recovery, select `Mount /system` (you may see some errors, but they can be safely ignored)
3. Select `Apply update from ADB`
4. Run `adb sideload Magisk-xxx.zip`
5. You will see a signature verification error, select `Yes` to bypass the check
6. Reboot to system to enjoy your Magisk installation.
Caveats
1. Since it's not TWRP, you cannot decrypt your /data in recovery for now, which means no data backup or recovery, and you cannot install on-device flashable zips through this recovery.
2. Since it's not TWRP, it cannot prevent your OS from overwriting recovery automatically. If you use official ROM, you may need to manually re-flash the recovery every time. I'm not sure whether this can be bypassed with some Magisk module.
3. Don't expect to be able to flash anything into /system (e.g. OpenGAPPS or magisk) on stock ROMs
4. When trying to install OpenGAPPS on custom roms, it will get stuck at the end of the flashing process. This does not affect the functionality of the installed system and gapps, and a force-reboot into system will work just fine.
5. You need to always click "Mount /system" before flashing any mods into the system (i.e. Magisk, OpenGapps, etc., ROMs themselves are not affected), otherwise they will fail to install. (Clicking the option does not actually mount /system; it just sets up necessary mappings from the super partition to each of the dynamic partitions so that the installation scripts will work)
Downloads
LineageOS Recovery (with vbmeta included inzide the zip) (17.1, 2020-05-05): https://github.com/Xiaomi-Curtana/a.../recovery-2020-05-05/los-recovery-curtana.zip
Source Code
Device Tree: https://github.com/Xiaomi-Curtana/android_device_redmi_curtana
Kernel: https://github.com/Xiaomi-Curtana/android_kernel_redmi_sm7125
This is amazing !!! :laugh::laugh::laugh:
I'm very very grateful, but what's the advantage over stock recovery if we can't flash zips inside the phone memory? Or if we can't take a data backup?
Just asking trying not to be rude
cimdrap said:
I'm very very grateful, but what's the advantage over stock recovery if we can't flash zips inside the phone memory? Or if we can't take a data backup?
Just asking trying not to be rude
Click to expand...
Click to collapse
Stock recovery can't flash custom rom, gapps or magisk
cimdrap said:
I'm very very grateful, but what's the advantage over stock recovery if we can't flash zips inside the phone memory? Or if we can't take a data backup?
Just asking trying not to be rude
Click to expand...
Click to collapse
With LOS recovery you can adb sideload roms like EvolutionX
After reboot to recovery. It stuck at LOS recovery menu screen not response to Vol up/down button.
Then about 10 seconds phone reboot to normal stage.
When I reboot to recovery again it became stock recovery screen no LOS recovery.
ps000000 said:
After reboot to recovery. It stuck at LOS recovery menu screen not response to Vol up/down button.
Then about 10 seconds phone reboot to normal stage.
When I reboot to recovery again it became stock recovery screen no LOS recovery.
Click to expand...
Click to collapse
You sure you read all the steps? And didn't just flash straight away
A greatest thanks to dev and tester to make this work. Thank you for all your hard work to make this work. More great things is coming soon!
Is it work on Pro Max?
ahmetrasittopal said:
Is it work on Pro Max?
Click to expand...
Click to collapse
No
QuantumShqipe said:
You sure you read all the steps? And didn't just flash straight away
Click to expand...
Click to collapse
Success now (BAD USB CABLE Haha).:laugh:
Can I install this recovery and work as twrp? then installing the xiaomi.eu rom? Thank you
Yuluga said:
Can I install this recovery and work as twrp? then installing the xiaomi.eu rom? Thank you
Click to expand...
Click to collapse
No
TheMalachite said:
No
Click to expand...
Click to collapse
so what is this recovery? to install the lineage rom?
Yuluga said:
so what is this recovery? to install the lineage rom?
Click to expand...
Click to collapse
No, it's for flash custom rom + flash gapps and magisk on custom rom only
TheMalachite said:
No, it's for flash custom rom + flash gapps and magisk on custom rom only[/QUOTE
Your responds is confusing. Recent post ask if you can flash roms with this recovery and you said no. And then the person ask you so whats this recovery for, you said to flash roms and gapps ect.
Soo can we flash roms and gapps and zips YES or NO?
Thanks.
Click to expand...
Click to collapse
Gearswar said:
TheMalachite said:
No, it's for flash custom rom + flash gapps and magisk on custom rom only[/QUOTE
Your responds is confusing. Recent post ask if you can flash roms with this recovery and you said no. And then the person ask you so whats this recovery for, you said to flash roms and gapps ect.
Soo can we flash roms and gapps and zips YES or NO?
Thanks.
Click to expand...
Click to collapse
Is Xiaomi.eu is a custom ROM ? No that's a MIUI port with more customization and debloated
Click to expand...
Click to collapse
Lame question
Do we need to unlock bootloader?
Or does it come unlocked by default
RickyGoldsmith said:
Lame question
Do we need to unlock bootloader?
Or does it come unlocked by default
Click to expand...
Click to collapse
You unlock it via mi unlock tool... https://en.miui.com/unlock/
Takes 7 days
Hi,
i have a problem, my micro SD Card cant be mountet.
i have flasht LRTWRP now.
Have anyone a tip for me? What can i do ?
big thx