[SOLVED] LG G4 stuck on Firmware Update screen - G4 Q&A, Help & Troubleshooting

Hi all. I'm writing because I didn't find anything useful to me.
My LG is stuck on Firmware Update screen:
https://drive.google.com/file/d/0B2dMoe8S9yx4VGNkR1VtMjVRdkU/view?usp=sharing
(below there are "633A B88 // Modified).
All began when I wanted to re-lock the bootloader. So, I read somewhere that I could do it with fastboot oem lock. I did it and the result was that the bootloader was re-locked. So I rebooted my phone and it stuck at
https://drive.google.com/file/d/0B2dMoe8S9yx4dDR5cDFQT0RIZ2c/view?usp=sharing
and there wasn't "may not work properly" but "it will not boot". So, I entered to download mode and I tried to flash with LGUP V20G kdz (I was on 29A but it's zipped). When it arrived at about 24% it stopped with error 0x2000 (but phone was identified). After this I rebooted my LG and I can access only to download mode. When I turn on the phone there isn't anymore "Your device is corrupt, etc.", directly to download mode. I tried to enter to download mode and recovery mode (but stock can only reset), so if someone knows others hardware button combinations to get other modes, please tell me.
I hope someone can help me, obviously not service.
Thank you in advance.
P. S. Sorry for my bad English

No one?
For me it's enough only a way to force installing firmware on LGUP.

popetto said:
Hi all. I'm writing because I didn't find anything useful to me.
My LG is stuck on Firmware Update screen:
SShttps://drive.google.com/file/d/0B2dMoe8S9yx4VGNkR1VtMjVRdkU/view?usp=sharing
(below there are "633A B88 // Modified).
All began when I wanted to re-lock the bootloader. So, I read somewhere that I could do it with fastboot oem lock. I did it and the result was that the bootloader was re-locked. So I rebooted my phone and it stuck at
SShttps://drive.google.com/file/d/0B2dMoe8S9yx4dDR5cDFQT0RIZ2c/view?usp=sharing
and there wasn't "may not work properly" but "it will not boot". So, I entered to download mode and I tried to flash with LGUP V20G kdz (I was on 29A but it's zipped). When it arrived at about 24% it stopped with error 0x2000 (but phone was identified). After this I rebooted my LG and I can access only to download mode. When I turn on the phone there isn't anymore "Your device is corrupt, etc.", directly to download mode. I tried to enter to download mode and recovery mode (but stock can only reset), so if someone knows others hardware button combinations to get other modes, please tell me.
I hope someone can help me, obviously not service.
Thank you in advance.
P. S. Sorry for my bad English
please delete SS for seeing photos; XDA doesn't leave me inserting photos because I'm new
Click to expand...
Click to collapse
I have exacly the same problem and i am looking for solution and when i use LGUP with stock rom it loads like 24# the got error 0x0200...
So i can't get stock rom and i get get in the bootloader TWRP...

popetto said:
Hi all. I'm writing because I didn't find anything useful to me.
My LG is stuck on Firmware Update screen:
SShttps://drive.google.com/file/d/0B2dMoe8S9yx4VGNkR1VtMjVRdkU/view?usp=sharing
(below there are "633A B88 // Modified).
All began when I wanted to re-lock the bootloader. So, I read somewhere that I could do it with fastboot oem lock. I did it and the result was that the bootloader was re-locked. So I rebooted my phone and it stuck at
SShttps://drive.google.com/file/d/0B2dMoe8S9yx4dDR5cDFQT0RIZ2c/view?usp=sharing
and there wasn't "may not work properly" but "it will not boot". So, I entered to download mode and I tried to flash with LGUP V20G kdz (I was on 29A but it's zipped). When it arrived at about 24% it stopped with error 0x2000 (but phone was identified). After this I rebooted my LG and I can access only to download mode. When I turn on the phone there isn't anymore "Your device is corrupt, etc.", directly to download mode. I tried to enter to download mode and recovery mode (but stock can only reset), so if someone knows others hardware button combinations to get other modes, please tell me.
I hope someone can help me, obviously not service.
Thank you in advance.
P. S. Sorry for my bad English
please delete SS for seeing photos; XDA doesn't leave me inserting photos because I'm new
Click to expand...
Click to collapse
https://forum.xda-developers.com/g4/development/h815-nougat-stock-t3659860/post73636739#post73636739

raptorddd said:
https://forum.xda-developers.com/g4/development/h815-nougat-stock-t3659860/post73636739#post73636739
Click to expand...
Click to collapse
Unfortunately didn't work for me. Thank you anyway.
Seksi69 said:
I have exacly the same problem and i am looking for solution and when i use LGUP with stock rom it loads like 24# the got error 0x0200...
So i can't get stock rom and i get get in the bootloader TWRP...
Click to expand...
Click to collapse
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
EDIT:
This dll works also for H818P

popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
Click to expand...
Click to collapse
Than you so MUCH i manage to Install new rom :*

popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
Click to expand...
Click to collapse
its the same file... same procedure.

raptorddd said:
its the same file... same procedure.
Click to expand...
Click to collapse
Same procedure but not same file: in the solution I linked and I used there are two DLLs (and I can see the difference on LGUP, that says "DLL version 0.4.0.0"); instead, in your solution (that I tried before using the one I linked), there's only a DLL and, if I'm not wrong, its version is 0.3.3.23 or something similar. Anyway, it's not a problem, I said it without any aim.

woohoo
popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
Click to expand...
Click to collapse
:victory:
Thank you, this fixed my phone. Had gone through quite a few different forum posts and none worked. Was getting close to having to use my ladies old iPhone :crying:

thank u verry much i have fixed the same problem too

popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
Click to expand...
Click to collapse
you saved my phone thank you this dll works on H818P too

thank you .replacing zip file change lgup DLL to 0.0.4.0 and it will not show error again.

Thanks
I did all of your instructions and my LG G4 back to life, i was searching for one answer can be usefull, thanks :good: it work for me

Thanks - popetto - saved me time and money
popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
EDIT:
This dll works also for H818P
Click to expand...
Click to collapse
Was starting to look for a new phone but this worked for me yesterday. Thanks again.

god bless you
You save my old G4, man you help me so much. send me a mail i ll give you paypal money to drink for me send me pm your mail.
Thx you did my day Hail from France
popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
EDIT:
This dll works also for H818P
Click to expand...
Click to collapse

popetto said:
Unfortunately didn't work for me. Thank you anyway.
I fixed in this way:
- go to https://forum.xda-developers.com/showpost.php?p=73493577&postcount=78 and download attached file. It contains two DLL that you'll put in C:\Program Files (x86)\LG Electronics\LGUP\model\8994 (deleting other DLL file). Don't worry if they are two DLLs and not one. Then, when you open LGUP you must flash (UPGRADE mode) H81520p firmware (that you can download here: http://storagecow.eu/index.php?dir=Xda/LG+G4/H815/). Then wait and your phone should revive, like mine. I hope it'll work for you as worked for me.
Obvioulsy you must have H815 version (not variant) to do this.
EDIT:
This dll works also for H818P
Click to expand...
Click to collapse
Thanks for sharing bro, Its worked

Related

LG G3 Hardbrick (F-400L)

Can anyone help me?
I flash a wrong recovery then it cnnot go to
download mode.they say that i need to jtag it
Can i do it my self?
Please help me
give me some instruction on how to jtag it
(LG G3 F400L)
Stiffmeistro said:
Can anyone help me?
I flash a wrong recovery then it cnnot go to
download mode.they say that i need to jtag it
Can i do it my self?
Please help me
give me some instruction on how to jtag it
(LG G3 F400L)
Click to expand...
Click to collapse
hello, if there is no juice, you can try to do as I did to my D855, I think it is the same, you will need to open your device and make a trick to go to downlaod mode.
IT is very esay that I put my LG G3 in download mode in 3minutes.
---------- Post added at 02:19 AM ---------- Previous post was at 02:08 AM ----------
just go with this guide , it is good.
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
I did like it said and I got my phone repaired.
But, in step 8, I suggest you to not flash all stuff, because I think It is not necessary, I am pretty sure this was my cause to have the message : "Can't find matched cust for NT-code mcc/mnc"
I hard bricked my phone a second time, but instead of doing step 8 like he says. I just Made SDRAM test also and start. it will flash necessary stuff and reboot phone automatically.
To make a summary of what you need to do:
-- first put your windows in test mode if you have windows 64bits and install drivers
1-put your phone in download mode (screen off and without battery-sort of emergency download mode)
2-run boarddiag by willcracker and extract your Bin file in a folder.
3-choose port and choose folder
4-run the AP check and EMMC test
5-Run AP check, Emmc test and SDRAM test
6-phone will reboot
7-put him in download mode and flash you tot file
Done!
all files in the link
majorak said:
hello, if there is no juice, you can try to do as I did to my D855, I think it is the same, you will need to open your device and make a trick to go to downlaod mode.
IT is very esay that I put my LG G3 in download mode in 3minutes.
---------- Post added at 02:19 AM ---------- Previous post was at 02:08 AM ----------
just go with this guide , it is good.
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
I did like it said and I got my phone repaired.
But, in step 8, I suggest you to not flash all stuff, because I think It is not necessary, I am pretty sure this was my cause to have the message : "Can't find matched cust for NT-code mcc/mnc"
I hard bricked my phone a second time, but instead of doing step 8 like he says. I just Made SDRAM test also and start. it will flash necessary stuff and reboot phone automatically.
To make a summary of what you need to do:
-- first put your windows in test mode if you have windows 64bits and install drivers
1-put your phone in download mode (screen off and without battery-sort of emergency download mode)
2-run boarddiag by willcracker and extract your Bin file in a folder.
3-choose port and choose folder
4-run the AP check and EMMC test
5-Run AP check, Emmc test and SDRAM test
6-phone will reboot
7-put him in download mode and flash you tot file
Done!
all files in the link
Click to expand...
Click to collapse
Can you explain the step 6-10 in the link you gave to me?
i understand it but i don't know if when i will click the start
btw i did not do anything yet,something is not right in my phone
there's still led lights when im charging sir then suddenly it will begone in a few minutes.
Stiffmeistro said:
Can you explain the step 6-10 in the link you gave to me?
i understand it but i don't know if when i will click the start
btw i did not do anything yet,something is not right in my phone
there's still led lights when im charging sir then suddenly it will begone in a few minutes.
Click to expand...
Click to collapse
first, just skip steps 8 and 9 and replace it with:
it is a little bit mixed up but this is what he wanted to say:
6- choose port and folder where you extracted TOT file.
7- Check "AP" and "EMMC" and press start
here you finished with the link.
8+9- you need to Check "AP" and "EMMC" and SDRAM , click Start.
10-flash you phone with LGUP using Refurbish and choosing the tot file. (I prefer LG UP)
download here:
http://forum.xda-developers.com/g4/help/lgup-install-kdz-mm-lp-t3249803 (do not install DLL file from this link)
but first install DLL file: http://downloads.codefi.re/autoprime/LG/LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.MSI
majorak said:
first, just skip steps 8 and 9 and replace it with:
it is a little bit mixed up but this is what he wanted to say:
6- choose port and folder where you extracted TOT file.
7- Check "AP" and "EMMC" and press start
here you finished with the link.
8+9- you need to Check "AP" and "EMMC" and SDRAM , click Start.
10-flash you phone with LGUP using Refurbish and choosing the tot file. (I prefer LG UP)
download here:
http://forum.xda-developers.com/g4/help/lgup-install-kdz-mm-lp-t3249803 (do not install DLL file from this link)
but first install DLL file: http://downloads.codefi.re/autoprime/LG/LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.MSI
Click to expand...
Click to collapse
Are you sure this is gonna work?
is this the method you use to your phone?
because i'm gonna do it
where did you get your method or what you did on your phone?
not the link you gave to me but the method you use
Stiffmeistro said:
Are you sure this is gonna work?
is this the method you use to your phone?
because i'm gonna do it
where did you get your method or what you did on your phone?
not the link you gave to me but the method you use
Click to expand...
Click to collapse
II followed the steps in this link as I sayed, but after that I recognised that I had to modify it a little (as I described also)
majorak said:
II followed the steps in this link as I sayed, but after that I recognised that I had to modify it a little (as I described also)
Click to expand...
Click to collapse
MAN, Thanks a lot!!!!!
I just follow your instruction and BAM!!
It work sir
MANY MANY THANKS :good: :fingers-crossed:
Stiffmeistro said:
MAN, Thanks a lot!!!!!
I just follow your instruction and BAM!!
It work sir
MANY MANY THANKS :good: :fingers-crossed:
Click to expand...
Click to collapse
I'm glad you fixed your G3, it is a very good phone

[GUIDE]How to install latest Marshmallow KDZ on the LG Spirit

Hello, as some of you may already know, we can't flash MM kdz on our LG Spirit using LG Flash Tool, so we have to use LG UP, a method which is also used by LG G4c owners. I drew the idea from them, since G4c and Spirit are practically the same devices. I've modified a script from G4c, all credits go to @bender_007.
So here are the steps:
1. Make sure you have USB drivers installed.
2. Download and install LG UP: http://www.filedropper.com/g4 ---- First install LGUP_8994_DLL_Ver_0_0_3_23, then LGUP_Install_Ver_1_14_3.
3. Download the script that makes LG UP recognize our device as H440n(Courtesy of @bender_007, I only modified small parts of it). Link: https://www.dropbox.com/sh/lbxdwloffi75qqg/AABfz5e9AIiSxipsnZQIiikGa?dl=0 (Download as zip)
4. Extract the zip and run h440n.bat
5. Connect your Spirit in MTP mode.
6. Run LG UP and wait for it to load.
7. Leave all settings as they are.
8. Under file path, browse to the kdz file you downloaded. NOTE: It won't show in the directory it is in, because the browse window sees only .tot files, so you have to manually type in the KDZ name in the text field and select it that way.
9. Click Start
10. Wait
11. ???
12. Profit! Enjoy your LG Spirit running Marshmallow!
Thanks, I had to manually copy the dll in the LGUP folder, dunno if it's my fault, or script's fault though.
EDIT: It gives me an error on boot, about CUST not existing... Nothing important, I can continue to use it but it's rather annoying? Fixes? Thanks.
guglicap said:
Thanks, I had to manually copy the dll in the LGUP folder, dunno if it's my fault, or script's fault though.
Click to expand...
Click to collapse
I suppose yours, because it worked for me flawlessly. If someone notices any errors in modifications I made to the script, feel free to correct me.
Fobos531 said:
I suppose yours, because it worked for me flawlessly. If someone notices any errors in modifications I made to the script, feel free to correct me.
Click to expand...
Click to collapse
Depending on OS and security level it can happen, it might need an elevated access- Try: right click - run as administrator
Poslano sa mog SM-G930F koristeći Tapatalk
Had to also copy everything over manually, running as admin didn't help. I haven't done anything to my security settings and am running on the only account that was created with the install. I think it might have something to do with me running on dev mode though.
jonixas said:
Had to also copy everything over manually, running as admin didn't help. I haven't done anything to my security settings and am running on the only account that was created with the install. I think it might have something to do with me running on dev mode though.
Click to expand...
Click to collapse
nah, I also run dev mode. No worries I'll create a desktop app which will then work.
Poslano sa mog SM-G930F koristeći Tapatalk
Afternoon fellas. I have reached the part of runinng the kdz via LGUP however the kdz i have (named H525n20c_00_0321.kdz) brings back an error of invalid kdz. Could someone be so kind as to point out a working link for the kdz if possible?
Thanks
Diarno said:
Afternoon fellas. I have reached the part of runinng the kdz via LGUP however the kdz i have (named H525n20c_00_0321.kdz) brings back an error of invalid kdz. Could someone be so kind as to point out a working link for the kdz if possible?
Thanks
Click to expand...
Click to collapse
Firstly, do you have LG Spirit or LG G4c?
guglicap said:
Thanks, I had to manually copy the dll in the LGUP folder, dunno if it's my fault, or script's fault though.
EDIT: It gives me an error on boot, about CUST not existing... Nothing important, I can continue to use it but it's rather annoying? Fixes? Thanks.
Click to expand...
Click to collapse
I had to manually move dll too. But I made it!
@Fobos531 hello good job . bro I can install MM on lg spirit 4g H440F
Mark XP said:
@Fobos531 hello good job . bro I can install MM on lg spirit 4g H440F
Click to expand...
Click to collapse
Wait until H440F kdz is released.
P.S.: I had to copy all files manually and manually Merge registry script. Probbably some Windows 10 BS with UAC and bat scripts lately.
Another BS, now from phone - MSC error on boot. But that temp root isn't availiable :/
Im stupid, what is MTP mode?
MadjijaHacker said:
Im stupid, what is MTP mode?
Click to expand...
Click to collapse
Regular mode what is enabled by Deafult on KitKat and newer ROM's. It is also known as Media Transfer Protocol and when you connect phone it should look something like this (screenshot from my PC with my current device connected because of copying nandroid backup to PC)
Antoher note: for LG Spirit it looks like Phone Icon, not Media Device.
​
midzan21 said:
Regular mode what is enabled by Deafult on KitKat and newer ROM's. It is also known as Media Transfer Protocol and when you connect phone it should look something like this (screenshot from my PC with my current device connected because of copying nandroid backup to PC)
Antoher note: for LG Spirit it looks like Phone Icon, not Media Device.
Click to expand...
Click to collapse
I knowed that, but i didnt know what is name of it.
i have a few questions, can i back to lollipop? and the adoptable storage is working?
BrainNotFound said:
i have a few questions, can i back to lollipop? and the adoptable storage is working?
Click to expand...
Click to collapse
Yes, you can get back by flashing kdz using LG Flash Tool and as far I saw there isn't enabled Adoptable Storage.
Can you do the same for the LG Spirit h420?
Can someone upload photos ?? Do you feel any diference ate speed or maneging RAM ??
jopafon said:
Can someone upload photos ?? Do you feel any diference ate speed or maneging RAM ??
Click to expand...
Click to collapse
Just check General Info Therad here (last 2-3 pages) - http://forum.xda-developers.com/android/development/lg-spirit-h440n-thread-t3108435
BrainNotFound said:
i have a few questions, can i back to lollipop? and the adoptable storage is working?
Click to expand...
Click to collapse
To anyone interested:
I got adaptive storage to work! It's pretty simple. Just follow the guide from modaco.com (search for "modaco adaptive storage galaxy s7" on google", I don't think I can post links).
Then go to Settings -> Storage & USB -> Your SD Card -> Merge (in the additional menu).

[Help] LG G4 H815 LGUP failure

Hello!
I tried to update my Vodafone Branded G4 with the europe not branded version H81520g_00_0720.kdz
The problem ist i just get "error code = 0x2000, invalid command response" from the LGUP software and everytime i start the phone it is in firmware update mode.
Any idea how to fix this?
Greetings
I got this too as I tried to install H81520o_00_0310.kdz then I thought that it is maybe related to the brand. So I download your kdz file and then it was working.
So I would guess try another number is the best what you can do. I believe it is because of selection of "upgrade". If you have a tot file for refurbish, then maybe another is working, but I didn't do this yet.
Probably the problem is the DLL.
Extract the DLL from the KDZ (the one you want to flash) and replace it with the one you have in LGUP (path; C:/Program files/LG Electronics/LGUP/Model/8992).
the_naxhoo said:
Probably the problem is the DLL.
Extract the DLL from the KDZ (the one you want to flash) and replace it with the one you have in LGUP (path; C:/Program files/LG Electronics/LGUP/Model/8992).
Click to expand...
Click to collapse
i have the same problem2.
all the kdz that i download not come with any dll files just a 1.73 gb one file size.
kobisa25 said:
i have the same problem2.
all the kdz that i download not come with any dll files just a 1.73 gb one file size.
Click to expand...
Click to collapse
you must extract it from the KDZ with this tool: Click Here
the_naxhoo said:
you must extract it from the KDZ with this tool: Click Here
Click to expand...
Click to collapse
hi so i extract the kdz from LGExtract&7za& manuall tool& when i use winrar to extract its tell me no archive found i try also in winzip software. do you have any idea what else 2do?
thank you.
You can also try the codefire dll: http://downloads.codefi.re/autoprime/LG/LG_G4
( Download and rename LGFLASH_LG_G4_CODEFIRE.dll )
sfX
GOT IT!
the_naxhoo said:
you must extract it from the KDZ with this tool: Click Here
Click to expand...
Click to collapse
so after a long long search and dosents off error i succeeded
i find the currect kdz ISRAEL one and from it i EXTRACT it with WindowsLGFirmwareExtract-1.2.5.0-Release dll file and downgraded to lollipop 5.5 only with this dll file i make it after i try a few rom stocks that work with the dll.
i want to thank you you direct me to the right way:good:
Hi,
I have LG H811 (T-Mobile) Variant. I receive error from LGUP everytime I try to flash this ROM=h81120x_00_1108.kdz
My LGUP shows COM =COM3 and Version=H81120v
The error is thrown at 9%
Nothing working for me I am very frustrated!!!
PLEASE SOMEBODY HELP ME!
Stuck with LG G4 (H81520i)
Same for me but with LG H81520i. I tried to flash these ROM* with their specific .dll that I extracted thanks to WindowsLGFirmwareExtract-1.2.5.0-Release. Always get "error code = 0x2000, invalid command response" from LGUP. The error is thrown at 16% on the computer, but at 7% on the phone. Now, I'm stuck in download mode. I also tried to change the COM port number, doesn't change anything.
*Europe General H81510B_00.kdz ; Europe OPEN H81510D.kdz ; H81510D_00.kdz ; H81520i_00_0922.kdz ; SEA H81510B.kdz
Only one ROM above matches the LG H81520i (the fourth one).
Informations about my (ex-)android firmware :
- Android version : 6.0 (Marshmallow)
- Kernel version : 3.10.84
- Software version : V20-SEA-XX
PS : H81520i is what is written on the LGUP software
______________________________________________________________________________
I found a solution (after several hours)
Uninstall all your LG softwares (except LG Bridge or others LG backup softwares) and go to 'C:\Program Files (x86)\LG Electronics\' to delete all folders and files.
Go to this link and click on "Download all". Extract the file and follow the instructions :
1) Install "LGMobileSupportTool.exe"
2) Install "LGMobileDriver_WHQL_Ver_4.2.0.exe"
3) Install "LGUP_Install_Ver_1_14_3.msi"
4) Install "LGUP_8994_DLL_Ver_0_0_3_23.msi"
5) Move "LGUP_8994.dll" in the repertory 'C:\Program Files (x86)\LG Electronics\LGUP\model\8994'
6) Open "LGMobile Support Tool" and click on "Install USB driver." to the left
7) Select "LGH815" (or your model) et follow the drivers installation steps
8) Do step 5) again
9) Shut off your LG and plug it to your computer while pressing volume up in order to enter download mode
10) Unplug your LG and the battery
11) Open "LGUP" and close it
12) Do step 9 again (download mode)
13) Open "LGUP", select "UPGRADE" and go select your .kdz file (the ones in the file that you downloaded or another one you have)
14) Click on "Start" and DON'T TOUCH !!!!!!
Big thanks to the people of this reddit post and of this XDA thread
See above
Back To Stock ROM LG G4 H811 (T-Mobile)
LucasDupanne said:
________________________________________________________
First of all, I'm not allowed to post links as a new user , so I put them with spaces that you must delete :laugh: . Good luck !
Uninstall ALL your softwares (except LG Bridge or others LG backup softwares) and go to 'C:\Program Files (x86)\LG Electronics\' to delete all folders and files.
Go to this link ( ht tps : / / ya di . sk /d / KIG5F8 2jmXcUR ) and click on "Download all". After downloading the file, extract it and follow the instructions :
1) Install "LGMobileSupportTool.exe"
2) Install "LGMobileDriver_WHQL_Ver_4.2.0.exe"
3) Install "LGUP_Install_Ver_1_14_3.msi"
4) Install "LGUP_8994_DLL_Ver_0_0_3_23.msi"
5) Move "LGUP_8994.dll" in the repertory 'C:\Program Files (x86)\LG Electronics\LGUP\model\8994'
6) Open "LGMobile Support Tool" and click on "Install USB driver." to the left
7) Select "LGH815" et follow the drivers installation steps
8) Do step 5) again
9) Shut off your LG and plug it to your computer while pressing volume up in order to enter download mode
10) Unplug your LG and the battery
11) Open "LGUP" and shut it
12) Do again step 8 (download mode)
13) Open "LGUP", select "UPGRADE" and go select your .kdz file (your one or the ones in the file that you downloaded)
14) Click on "Start" and DON'T TOUCH !!!!!!
==>> thanks to ' ht tps : / / www .reddit . com /r/lgg4/comments/7anayg/downgraded_from_n_to_mm_and_stuck_in_download / ' post
A french man of 15 years that thanks Lobster_Johnson123 very very much.
PS : Sorry, my english is bad And let me know !!! :fingers-crossed:
Click to expand...
Click to collapse
Thanks Lucas for your time and help. It didn't work for me. I flashed another ROM named H811V20r_00_0111.kdz and it worked like a charm and it's tested on so many devices afterwards which worked fine without a single issue.
Here is the link to the ROM: https://lg-roms.com/official-firmware/LG G4-LGH811VK/H811V20r_00_0111/
Thanks for the help though.
androhead said:
Thanks Lucas for your time and help. It didn't work for me. I flashed another ROM named H811V20r_00_0111.kdz and it worked like a charm and it's tested on so many devices afterwards which worked fine without a single issue.
Here is the link to the ROM:
Thanks for the help though.
Click to expand...
Click to collapse
Happy it worked an other way for you !
i had working H815 version 29A nougat installed but for some reason
( nougat restarting issue ) during flashing H815 version 10d , after 9 percent same error comes , i tried by copying extracted dll from H815 v10d kdz in the LGUP (8994 folder) but nothing works for me,
please friends come to resolve my issue. waiting for reply from xda experts
Sanaullahshuaib said:
i had working H815 version 29A nougat installed but for some reason
( nougat restarting issue ) during flashing H815 version 10d , after 9 percent same error comes , i tried by copying extracted dll from H815 v10d kdz in the LGUP (8994 folder) but nothing works for me,
please friends come to resolve my issue. waiting for reply from xda experts
Click to expand...
Click to collapse
You need H81520p.kdz to downgrade from Nougat!
You can download from here: https://www.4shared.com/file/hfyqh6iEfi/H81520p_00_0314.html
Can also see here if you need more files: https://forum.xda-developers.com/showpost.php?p=76571471&postcount=23
Okay I'll try this but please tell me that
I have to copy lgup_8994.dll from H81520p or use original dll which is installed with the LGUP 8994 installer???
Sanaullahshuaib said:
Okay I'll try this but please tell me that
I have to copy lgup_8994.dll from H81520p or use original dll which is installed with the LGUP 8994 installer???
Click to expand...
Click to collapse
After install everything, replace the one in "C:\Program Files (x86)\LG Electronics\LGUP\model\8994" by the given one (or extract from the H81520p.kdz file).
See on the picture how your phone should be detected in "Device Manager":
http://i1376.photobucket.com/albums/ah39/RuedasLocas/Varios/Sem Tiacutetulo_zpsrrscdqov.jpg
H815v20p flashed correctly but mobile in boot-loop then i back installed H815v10d the original but also restarting
xda experts???
whats the issue in your mind experts XDA???
Sanaullahshuaib said:
H815v20p flashed correctly but mobile in boot-loop then i back installed H815v10d the original but also restarting
xda experts???
whats the issue in your mind experts XDA???
Click to expand...
Click to collapse
You first start your phone with any sim or sd card?
Try to flash it again with the v20p and restart it without any card on it.
If it doesn't solve the problem, try a v10a. Maybe it works and you can upgrade starting from there.
Good luck!
now again I tried H815v29A so it installed after the installation of old original version , now please tell the method of rooting Nougat on H815v29A urgently XDA experts???
also Twrp not installing on H815v29A which was working on marshmallow/////
experts reply???

LG V30 Unbrick guide (Qualcomm EDL 9008 Mode, Hardbirck, with no download mode)

If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------​1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
you can create rawprogramer and patch.xml with this program
I have already tried it on lg v10 kdz with successful.
after extract kdz :
1-open qualcomtool 2.4 and go to EMMC tabe.
2-clic browse and select primarygpt_0.bin
3- select all partitions and click exract partition
4- click extract firmware
you will find every things you need in extracted folder.
you can edid rowprogramer.xml with notepad ++ .
edit : tryed with lg v30 kdz not work
(gpt not present when select file)
Thank you for your work
download problem
quickwshell said:
If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------​1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
Click to expand...
Click to collapse
thank you so much,but can't download zip from this website,if you can offer other download way,such as google,mega,onedrive,i will apreciate it so much,thanks for your work
Johoneycn said:
thank you so much,but can't download zip from this website,if you can offer other download way,such as google,mega,onedrive,i will apreciate it so much,thanks for your work
Click to expand...
Click to collapse
Sorry for the late reply
mega. nz/#!zCZBkC4D!Vxo9wrd1c9vsZgCfQIrLelcp3unTY7sJAqMXjANvzjQ is V30_UNBRICK.zip
and mega. nz/#!PLIBzQ6L!JKtfq_RH2iFgcQckkRi_LtZGt9u2zaO2YF6x8dtHL6A is a firehose.
It is a shame we resort to such lengths for this. Shame on vendors. It is like pure gold or diamonds when we come across a programmer...
Hi, @quickwshell, could you see this: Help! bootloop per 5 sec, cannot enter rec, download or fastboot. Does the problem I'm facing now is what your method targeting to?
@quickwshell
Thank you so much for sharing firehorse for v30 and this solution. I have LS998 bricked bootloop after interrupting upgrade as @zacox123. I tried your files posted but still phone cant get download mode. Now Im trying to create rawprogram.xml and patch.xml from specific firmware model ls998 but I want to know what partitions are necesary just for getting download mode and then try to upgrade for usb mode.
Could you please help me?
thanks in advance
Pulian said:
@quickwshell
Thank you so much for sharing firehorse for v30 and this solution. I have LS998 bricked bootloop after interrupting upgrade as @zacox123. I tried your files posted but still phone cant get download mode. Now Im trying to create rawprogram.xml and patch.xml from specific firmware model ls998 but I want to know what partitions are necesary just for getting download mode and then try to upgrade for usb mode.
Could you please help me?
thanks in advance
Click to expand...
Click to collapse
How did you do with your phone? Have you made your phone into 9008 mode? Did you use the correct tool?
I have not processed my problem yet. But I read some other posts introducing that, use qpst or miracle box or any similar tools with the edl file provided by @quickwshell to flash in twrp directly, instead of getting download mode back. Maybe you can have a trial.
I was converting my lg [email protected] for unlocking. I have tools for flashing and I did it before with others phones. Accidently flashing process was interrupted and phone got that condition, no download mode. Now I'm using testpoint connection and UMT (tool for repair Qualcomm Phones) for trying to recover download mode. I suppose you can use QFIL for programming after we have correct rawprogramer.xml and patch.xml. Let me finish my test and I'll post results.
Pd: bootloader is not unlocked and I don't know if I can write twrp and it'll work.
Could you share links referring this topic and phone? Thanks.
Well, it definitely worked :good:.
Partitions extracted from us998 firmware
. Now I'm flashing again.
Pd: sorry for inverted picture. I make it from cellphone without edition
Do we need any special process before the computer work, @quickwshell and @Pulian? Is any special cable or teardown work needed? I have never used 9008 before but see other brands like xiaomi cannot simply enter 9008 mode directly.
---------- Post added at 04:27 PM ---------- Previous post was at 04:08 PM ----------
Pulian said:
Well, it definitely worked :good:.
Partitions extracted from us998 firmware
. Now I'm flashing again.
Pd: sorry for inverted picture. I make it from cellphone without edition
Click to expand...
Click to collapse
I see octoplus in your pic. Could you please share your tools and detailed steps? I have never tried 9008, so I hope some extra hand-by-hand instructions. Thanks.
The post I read is from an Android community app, and I'm afraid I cannot provide a link to it. And the author of that post said he had not tested yet, just some common sense and rough idea. I'd hear more from you, afterwards you have succeeded.
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
nate0 said:
It is a shame we resort to such lengths for this. Shame on vendors. It is like pure gold or diamonds when we come across a programmer...
Click to expand...
Click to collapse
yes,i think so too, lg is too bad on the software
Pulian said:
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
Click to expand...
Click to collapse
After getting download mode back, do we need chiperase like @quickwshell mentioned? I don't know if octoplusbox did it before writing firmware and I suppose most people would still use LGUP for firmware writing. Did you lose s/n, imei, etc. after phone booting? If not, I guess partition dl should be OK.
I didnt touch imei and security partitions. My phone worked after flashing without problems.
Pulian said:
Thanks again @quickwshell. Firehorse file is the most important think for starting.
1. I extracted files partitions from firmware KDZ using this software https://forum.xda-developers.com/showthread.php?t=2600575
2.. I used testpoint for getting EDL (QUALCOM 9008) connection. https://forum.xda-developers.com/showpost.php?p=78573920&postcount=2
3. I tried firmware posted here without success (Maybe it works on others). So I wrote critical partitions extracted from my specific firmware (US998) using UMT box and I didnt need to create .xml files because this tool can read and detect internal partitions.
4. I got download mode and just write firmware by USB using octoplusbox. Phone Alive!!
I think every step here can be replaced using diferent software. good luck!
Click to expand...
Click to collapse
I searched a lot for UMT Box and it seems like one has to collect it with the dongle or else it's not gonna work. Getting frustrated here Are there any way other than umt? Can you or anyone suggest?
moyedchowdhury said:
I searched a lot for UMT Box and it seems like one has to collect it with the dongle or else it's not gonna work. Getting frustrated here Are there any way other than umt? Can you or anyone suggest?
Click to expand...
Click to collapse
use cracked miracle box
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
THANKS FOR COMING BACK. Mine is a LS998 converted into US998.
I'm So disappointed right now. Past few days have been unbearable. Even my Blood pressure is getting high
I'll describe what happened so that the situation is understood and you could suggest accordingly.
*I unlocked bootloader by wtf method.
*Tried several roms.
*Decided to stay on LOS 17.1 Q [Nearly got f*****g everything]
*Flushed a module via magisk which offered pixel boot animation(actually was searching for smartpixel to turn off 50% pixels)
*Rebooted and the device stuck into bootloop
*Rebooted into fastboot mode and reinstalled twrp and reboot- No luck
*Used a guide to wipe different partitions via fastboot and then reinstall twrp. Success but still boot stuck.
*Tried to go into download mode by pressing volume up while connecting USB, went into the mode but "waiting for any connection..." showed and was not detected by device mgr.
*Thought relocking the bootloader might get me into download mode.(That's when I burnt my luck I guess...)
*Did lock the bootloader.
*Aaaand still not detected in device manager.
*Moreover, now showing that Your device has failed a routine security check and will not boot!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
*Opened the back and test pointed motherboard, detected in 9008 mode
*Tried QFIL with V30_Unbrick.zip, sahara error.
*Tried a bunch of other tools most of them were so old that they didn't even have the firehose for this model.
Please someone help.
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
Can't thank you enough mate! Used it and miracle did happen. I even tried to use it before but after you said it, I tried hard this time. Searched here and there, then took some risk and started to do things like this way -
I had V30_UNBRICK.zip unzipped in a folder with firehose and xml files.
*Disable defender or any other antivirus. (Normally not recommended, but it's the first thing I do when doing these things, also I have an extra laptop where I do all these which doesn't have any private or necessary files, never had any problem though).
*Also, disable driver signature enforcement on Windows(https://windowsreport.com/driver-signature-enforcement-windows-10/)
1. I searched and found Miracle box Thunder v2.93 with loader (No box needed)
2. Select Qualcomm, then flashing and Write Flash.
3. Untick the auto button beside firehose.
4. Under "write flash"
see this image
i. Select firehose, this doesn't recognize the .elf file so renamed it to .mbn (finger was crossed) and it worked!
ii. There are six rawprogram?.xml and patch?.xml (Here, ? = 1, 2, 3....6), I only used rawprogram0.xml and
iii. patch0.xml
5. Got everything ready and then detached the phone from cable.
6. Pressed the start button right after entering into Testpoint EDL Mode. The process starts and failed after a while due to missing files. Then I matched which files were present corresponding to the lines in the xml file, after that deleted all the extra lines(i. e. file was not present in the V30_UNBRICK.zip) from rawprogram0.xml and saved the file (patch0.xml was untouched). I used Notepad++ for editing.
7. Again detached the phone, detached battery, reattached battery, pressed the start button right after I shorted the edl test points, even before the device was detected in the device manager, no delay.
8. The process was completed, files flashed. These files were flashed so that we can now flash proper kdz with download mode. Do not turn on the phone. Or else you'll get into bootloop.
9. Detached the battery, shorted power button for a while(skip if you don't understand), reattached the battery.
10. Pressed volume up and inserted USB cable. Not detected first time. Detached and reattached with pressing volume up button hard this time.
11. witnessed one of the happiest moment seeing it was detected as an LG device in device manager. Wasn't 100% sure yet.
12. Flashed chiperase(important) with patched LGUP in dev mode. And it was done.
13. I will upload the XML file, you can use it with the existing files inside V30_UNBRICK.zip.
the xml file here
Before doing all that I spent five horrific days searching for a solution and almost ordered a motherboard from Aliexpress with a price tag of $100. I tried to be as elaborative as possible so that whoever next encounter the issue don't have to go through what I experienced past few days. If you're reading this and having a problem understanding anything, read again, repeat 10 times, then repeat more 10 times(worked for me), still no solution? knock me here (also: [email protected]). I could help you(with v 30, g6) remotely if I have time, no charges, donate if you will and if you don't I'll still be happy to help. Keep flashing, peace.
---------- Post added at 05:36 AM ---------- Previous post was at 04:57 AM ----------
quickwshell said:
If you try this method, I nor anybody else is responsible for any further damage done to your phone.
Models Confirmed : V300L
We currently have firehose for V30.
Therefore, we can program UFS flash memory in 9008 mode.
It requires rawprogram?.xml(s) and patch?.xml(s) to program it.
It's easy to generate rawprogram?.xml(s) from kdz file, but generate patch?.xml(s) is not easy. (Unfortunately, I couldn't have time to generate patch?.xml(s)).
I have edited kdztools to generate rawprogram?.xml(s) easily (You can generate it by using "-r" argument. Currently, generate patch?.xml(s) is not supported. I'll add it soon).
I used patch?.xml(s) in post. it works well, but boot loop in the LG Logo.
However, it was possible to enter download mode.
------------------- GUIDE -------------------​1. Download rawprogram?.xml patch?.xml with images from link. (It uses V300L30h000906.kdz)
2. Download firehose (prog_ufs_firehose_8998_lgev30.elf) from link.
<< Linux >>
3. Build qdl or download pre-built binary
4. Extract zip or tar.gz files 1, 2, 3 in any folder.
5. Run
Code:
$ ./qdl --storage ufs prog_ufs_firehose_8998_lgev30.elf rawprogram0.xml patch0.xml rawprogram1.xml patch1.xml rawprogram2.xml patch2.xml rawprogram3.xml patch3.xml rawprogram4.xml patch4.xml rawprogram5.xml patch5.xml rawprogram6.xml patch6.xml
in the terminal.
6. If LG logo shows, enter to the download mode.
<< Windows >>
3-6. You can program by QFIL similar as qdl.
7. Connect to any Windows PC with LGUP (must support Android Pie).
8. Flash kdz with ChipErase. (IMPORTANT)
9. If it boots successfully, your device has unbricked.
Click to expand...
Click to collapse
Thank you, Your post helped me to understand a lot of things. Without whome I'd be having an expensive brick which can't even be used to build anything.
This is the way I recovered. So posting it here for people might get help.
seloka180 said:
use cracked miracle box
Click to expand...
Click to collapse
Can't thank you enough mate! Used it and miracle did happen. I even tried to use it before but after you said it, I tried hard this time. Searched here and there, then took some risk and started to do things like this way -
I had V30_UNBRICK.zip unzipped in a folder with firehose and xml files.
*Disable defender or any other antivirus. (Normally not recommended, but it's the first thing I do when doing these things, also I have an extra laptop where I do all these which doesn't have any private or necessary files, but never had any problems).
*Also, disable driver signature enforcement on Windows(https://windowsreport.com/driver-sig...nt-windows-10/)
1. I searched and found Miracle box Thunder v2.93 with loader (No box needed)
2. Select Qualcomm, then flashing and Write Flash.
3. Untick the auto button beside firehose.
4. Under "write flash"
see this image
i. Select firehose, this doesn't recognize the .elf file so renamed it to .mbn (finger was crossed) and it worked!
ii. There are six rawprogram?.xml and patch?.xml (Here, ? = 1, 2, 3....6), I only used rawprogram0.xml and
iii. patch0.xml
5. Got everything ready and then detached the phone from cable.
6. Pressed the start button right after entering into Testpoint EDL Mode. The process starts and failed after a while due to missing files. Then I matched which files were present corresponding to the lines in the xml file, after that deleted all the extra lines(i. e. file was not present in the V30_UNBRICK.zip) from rawprogram0.xml and saved the file (patch0.xml was untouched). I used Notepad++ for editing.
7. Again detached the phone, detached battery, reattached battery, pressed the start button right after I shorted the edl test points, even before the device was detected in the device manager, no delay.
8. The process was completed, files flashed. These files were flashed so that we can now flash proper kdz with download mode.
9. Detached the battery, shorted power button for a while(skip if you don't understand), reattached the battery.
10. Pressed volume up and inserted USB cable. Not detected first time. Detached and reattached with pressing volume button hard this time.
11. witnessed one of the happiest moment seeing it was detected as an LG device in device manager. Wasn't 100% sure yet.
12. Flashed chiperase(important) with patched LGUP in dev mode. And it was done.
13. I will upload the XML file, you can use it with the existing files inside V30_UNBRICK.zip.
the xml file here
Before doing all that I spent five horrific days searching for a solution and almost ordered a motherboard from Aliexpress with a price tag of $100. I tried to be as elaborative as possible so that whoever next encounter the issue don't have to go through what I experienced past few days. If you're reading this and having a problem understanding anything, read again, repeat 10 times, then repeat more 10 times(worked for me). Keep flashing, peace.

[Q&A] ASUS Fonepad 7 K00E ME372CG - looking for correct files for xFSTK

Please, where can I find ME372CG files for xFSTK?
I want to restore bootloader of my ME372CG tablet.
I follow these instructions, which are for FE170CG:
https://forum.xda-developers.com/android/help/asus-fonpad-7-fe170cg-bricked-stuck-t3740819
But I did not find ME372CG files for xFSTK.
So I took them from official Asus ME372CG firmware (from UL-K00E-WW-7.6.0.0-user.zip).
I found different file names in ifwi folder and I am not sure, which to use fo xFSTK:
dnx_fwr_ctp_???.bin
ifwi_ctp_???.bin
CLVP_CSAB_FWR_DnX_20.29.bin
ME372CG_32_IFWI_v54.57_CSAB_PROD.bin
I could not find any Softfuse file either.
Most probably I do not have the correct files, because xFSTK download does not work.
The file names, which I used, and the result from xFSTK can be found here:
https://www.dropbox.com/s/cz8imzdrs1r551r/xFSTK_ME372CG files.JPG?dl=0
Where can I find the correct files for xFSTK?
Thank you very much.
Greetings from Slovakia
Juraj
---
Cause of malfunction:
My tablet reported some kind of UI error, so I restarted it (still within Android),
but it never started again. It just vibrates when switching on, always black screen (only almost unnoticeable flash of light on LCD, during switching on). The battery is full - I measured it.
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Teddy Lo said:
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Click to expand...
Click to collapse
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
sid.1375 said:
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
Click to expand...
Click to collapse
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
jurajhotovy said:
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
Click to expand...
Click to collapse
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
sid.1375 said:
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
Click to expand...
Click to collapse
Hi
Finally, did you can find a solution for K00E?
miter8 said:
Hi
Finally, did you can find a solution for K00E?
Click to expand...
Click to collapse
Unfortunately no.
Sorry for the late response.

Categories

Resources