Can anyone help me?
I flash a wrong recovery then it cnnot go to
download mode.they say that i need to jtag it
Can i do it my self?
Please help me
give me some instruction on how to jtag it
(LG G3 F400L)
Stiffmeistro said:
Can anyone help me?
I flash a wrong recovery then it cnnot go to
download mode.they say that i need to jtag it
Can i do it my self?
Please help me
give me some instruction on how to jtag it
(LG G3 F400L)
Click to expand...
Click to collapse
hello, if there is no juice, you can try to do as I did to my D855, I think it is the same, you will need to open your device and make a trick to go to downlaod mode.
IT is very esay that I put my LG G3 in download mode in 3minutes.
---------- Post added at 02:19 AM ---------- Previous post was at 02:08 AM ----------
just go with this guide , it is good.
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
I did like it said and I got my phone repaired.
But, in step 8, I suggest you to not flash all stuff, because I think It is not necessary, I am pretty sure this was my cause to have the message : "Can't find matched cust for NT-code mcc/mnc"
I hard bricked my phone a second time, but instead of doing step 8 like he says. I just Made SDRAM test also and start. it will flash necessary stuff and reboot phone automatically.
To make a summary of what you need to do:
-- first put your windows in test mode if you have windows 64bits and install drivers
1-put your phone in download mode (screen off and without battery-sort of emergency download mode)
2-run boarddiag by willcracker and extract your Bin file in a folder.
3-choose port and choose folder
4-run the AP check and EMMC test
5-Run AP check, Emmc test and SDRAM test
6-phone will reboot
7-put him in download mode and flash you tot file
Done!
all files in the link
majorak said:
hello, if there is no juice, you can try to do as I did to my D855, I think it is the same, you will need to open your device and make a trick to go to downlaod mode.
IT is very esay that I put my LG G3 in download mode in 3minutes.
---------- Post added at 02:19 AM ---------- Previous post was at 02:08 AM ----------
just go with this guide , it is good.
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
I did like it said and I got my phone repaired.
But, in step 8, I suggest you to not flash all stuff, because I think It is not necessary, I am pretty sure this was my cause to have the message : "Can't find matched cust for NT-code mcc/mnc"
I hard bricked my phone a second time, but instead of doing step 8 like he says. I just Made SDRAM test also and start. it will flash necessary stuff and reboot phone automatically.
To make a summary of what you need to do:
-- first put your windows in test mode if you have windows 64bits and install drivers
1-put your phone in download mode (screen off and without battery-sort of emergency download mode)
2-run boarddiag by willcracker and extract your Bin file in a folder.
3-choose port and choose folder
4-run the AP check and EMMC test
5-Run AP check, Emmc test and SDRAM test
6-phone will reboot
7-put him in download mode and flash you tot file
Done!
all files in the link
Click to expand...
Click to collapse
Can you explain the step 6-10 in the link you gave to me?
i understand it but i don't know if when i will click the start
btw i did not do anything yet,something is not right in my phone
there's still led lights when im charging sir then suddenly it will begone in a few minutes.
Stiffmeistro said:
Can you explain the step 6-10 in the link you gave to me?
i understand it but i don't know if when i will click the start
btw i did not do anything yet,something is not right in my phone
there's still led lights when im charging sir then suddenly it will begone in a few minutes.
Click to expand...
Click to collapse
first, just skip steps 8 and 9 and replace it with:
it is a little bit mixed up but this is what he wanted to say:
6- choose port and folder where you extracted TOT file.
7- Check "AP" and "EMMC" and press start
here you finished with the link.
8+9- you need to Check "AP" and "EMMC" and SDRAM , click Start.
10-flash you phone with LGUP using Refurbish and choosing the tot file. (I prefer LG UP)
download here:
http://forum.xda-developers.com/g4/help/lgup-install-kdz-mm-lp-t3249803 (do not install DLL file from this link)
but first install DLL file: http://downloads.codefi.re/autoprime/LG/LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.MSI
majorak said:
first, just skip steps 8 and 9 and replace it with:
it is a little bit mixed up but this is what he wanted to say:
6- choose port and folder where you extracted TOT file.
7- Check "AP" and "EMMC" and press start
here you finished with the link.
8+9- you need to Check "AP" and "EMMC" and SDRAM , click Start.
10-flash you phone with LGUP using Refurbish and choosing the tot file. (I prefer LG UP)
download here:
http://forum.xda-developers.com/g4/help/lgup-install-kdz-mm-lp-t3249803 (do not install DLL file from this link)
but first install DLL file: http://downloads.codefi.re/autoprime/LG/LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.MSI
Click to expand...
Click to collapse
Are you sure this is gonna work?
is this the method you use to your phone?
because i'm gonna do it
where did you get your method or what you did on your phone?
not the link you gave to me but the method you use
Stiffmeistro said:
Are you sure this is gonna work?
is this the method you use to your phone?
because i'm gonna do it
where did you get your method or what you did on your phone?
not the link you gave to me but the method you use
Click to expand...
Click to collapse
II followed the steps in this link as I sayed, but after that I recognised that I had to modify it a little (as I described also)
majorak said:
II followed the steps in this link as I sayed, but after that I recognised that I had to modify it a little (as I described also)
Click to expand...
Click to collapse
MAN, Thanks a lot!!!!!
I just follow your instruction and BAM!!
It work sir
MANY MANY THANKS :good: :fingers-crossed:
Stiffmeistro said:
MAN, Thanks a lot!!!!!
I just follow your instruction and BAM!!
It work sir
MANY MANY THANKS :good: :fingers-crossed:
Click to expand...
Click to collapse
I'm glad you fixed your G3, it is a very good phone
Related
MICROMAX A65 ROOTED!!
[Sorry Guys!!!!]
As my father always says creating something is much less difficult that maintaining it,well this happened once again for me!!!.
I found maintaining this thread difficult I am officially announcing that you may stop expecting updates on this thread.Hats off to sssomnath474 to giving a new life to it!!!And it looks more informative as well!!
To add salt to injury A65 which my wife was holding is having issues with front speaker.Even after its trip back from the service centre gurus,it again managed to holdon the issue.I have given up on the micromax guys as of now.
GUYS,PLEASE FOLLOW THE BELOW THREAD BY sssomnath474 HENCEFORTH
http://forum.xda-developers.com/showthread.php?t=2501464
Recent activities as on 07 Aug 2013
--------------------------------------------------------------------------------------
1.Unlocked boot image and rooted it.
2.Install CWM.
3.Flashed firmware
4.sssomnath474 installed xloud,beats,bravia and confirmed it is working.
5.sssomnath474 also made few modification with UOT and came up with update.zip.
6.Right now we have unlocked V4 boot img which according to sssomnath474 has battery life updation.
7.I am studing as much time i can extract for an OC kernel and sssomnath474 is working on a rom.
8.As update by sssomnath474 this boot.img can have a better battery backup
http://www.mediafire.com/download/opweg2nwd0hk5dw/new_boot.img
let me know if you guys have access issues with any of the links or any of the link appears to be dead
9.Added a user guide how to flash the firmware.Hope it helps
http://www.mediafire.com/download/h2q51j8ovn1m1pc/Flash_firmware_config.pptx
10.you can use windows 7(you have to boot it in test mode and run the research downloader in administrator)
Thanks to sssomnath474 for the info
11.you can use unlock root as confirmed by sssomnath474
Thanks to sssomnath474 for this info
12.LIST OF STOCK IMAGES/PAC FILES FOR ALL MICROMAX MODELS
http://www.moulnisky.com/index.php?dir=Micromax
Thanks to sssomnath474 for this info
13.Heard from sssomnath474 that somebody has bumped imei while flashing.If any of you is stuck with the same issue i would suggest a complete firware flash following this tutorial,ONLY difference in this case will be DONT use my modified boot.img just flash the pac file as it is.
14.WoW! guys never thought this thread will get mushroomed like this....thanks to sssomnath474 ,shubhamym21 ,J.E.abhishek kumar and others for keeping things rolling
15.Some of you are facing weird problems with sims as my quick scan through the posts suggested,any updates on this guys?
I made changes to OP what sssomnath474 suggested, i am saying again all you need to do in the research downloader is select the pac file,uncheck calibration.
16.pradipkunwar51 has reported issue with docomo sim after flashing,i believe shubhamym21 already found a solution to it.Will Update the OP as soon as he comes back with comments
17.Critical Update:Tutorial & Tool if you messed up your EMI
Tutorial can be found here : China spd adnroid phone imei change just one click
& here is the download link : Android SPD IMEI Writing Tool_R1.5.3001 - Download - 4shared - maroof azam
Thanks to shubhamym21 for sharing the link and tutorial
18.Moved all updates under this activity section for better clarity
19.Adding Bravia engine zip
http://forum.xda-developers.com/showpost.php?p=44487763&postcount=138
Thanks to sssomnath474 for the link
--------------------------------------------------------------------------------------
Finally rooted my Micromax A65.Follow the guide carefully to avoid mistakes.I am not responsible for any physical/logical damage to you and your device .
Thanks to authors and their posts
http://forum.xda-developers.com/showthread.php?t=2165554 ElectronikHeart(Guru of spreadtrum)
http://forum.xda-developers.com/showthread.php?p=42693514#post42693514 Yekdall (confirming me unlocking the boot.img is key)
http://forum.xda-developers.com/showthread.php?p=42776196#post42776196 Intex12345(calibartion tabs needs to be unckecked in RD)
http://whiteboard.ping.se/Android/Rooting (for unlocking the boot.img)
Foreground
A Chaina re-branned phone
A fastboot mode
A useless recovery mode
A locked boot.img (thats why even chmod or simply pushing a su will not root the phone)
A IMEI number(which if you mess up after flashing,you will not get any radio signals)
1)First Unlock the Boot IMG
Before you proceed I will strongly recommend to download the tutorial guide ppt that you will find in Recent Activity list at the top of this post
You need to tamper permission after extracting the boot.img for this.No worry guys i have already done that for you .Just download the below file
Unsecured Boot Image
Now a bit critical part,read carefully .This unlocked image needed to be flashed to your device.For that you need research download and firmware pac file.
Download this to files from the below links
PAC versions & Tools Download
(pac file,driver,research download all included)
Download this drivers and install,after successfull installtion you will have(under device manager)
1.ABD interface
2.two COM ports
3.two emulators
If any of this having yellow sign it will not work.
Open research download
click on first button and load pac file
click on second button change baudrate to 115200,in calibration tab uncheck all.
For BOOT_IMG option browse and select the unlockedboot.img that you downloaded now.
plugin the usb cable(DON'T plugin the phone now)
click on play button
PRESS & HOLD VOLUME UP KEY and insert the usb cable,don't release the key.
Download should starts within 3 secs.If it doesn't then check the drivers carefully or reply to this thread with failures.
Once done unplug your phone and remove battery for 3 second
Reinsert battery and restart your phone.
YES!! you have successfully unlocked the boot.img
2)WiseMen Backup!!
First thing you should do before any tweaking and twisting save your back!!.Install CMW using the below method straight away and save your back.
1.Download .andriod.zip,extract it and save it under C:\Users\<computer name>\<paste it here>
http://www.mediafire.com/download/ga5tk2h89m41ddk/.android.zip
2.From your phone got to application-->developer option-->enable usb debugging
3.Now plugin your phone through micro usb cable.
4.Download this zip ,extract and place in under c:/<paste it here>
http://www.mediafire.com/download/s2as5grqceqtqq3/Android_Multi_tool.zip
5.Open a command prompt type
Code:
cd C:\Android Multi tool
C:\Android Multi tool>fastboot devices
20080823 fastboot
Note:you will NOT be able to proceed further if this doesnt shows up.Double check the andriod.zip has adb_usb.ini file.
Now we will flash a custom recovery image in fastboot mode.
Code:
C:\Android Multi tool>fastboot flash recovery recovery.img
sending 'recovery' (10240 KB)...
OKAY [ 10.487s]
writing 'recovery'...
OKAY [ 3.425s]
finished. total time: 13.918s
7.Reboot your phone.
8.Now got to CMW using Volume up + power button and do a backup.
3)Push superuser zip & ROOT!!!
This the easiest step among all of them.Download the below file,put it under sdcard and flash it through CMW.
http://www.mediafire.com/download/t55b6ebzvx9yf1f/update.zip
THAT'S IT you are rooted!!!
REMEMBER,PROBABILITY OF BRICKING IS MINIMUM AS I HAVE ALREADY DONE ALL THE TEST FOR YOU GUYS !!!.STILL IF ANYTHING GOES WRONG DONT PANIC,JUST FLASH A FIRMWARE AS MENTIONED ABOVE(point 1) EVENIF YOUR PHONE IS
TOTALLY DEAD .
----------------------------------------------------------------------------------------------
Please hit thanks if i you find this useful
No body tested it yet ?
question
sayannayas said:
No body tested it yet ?
Click to expand...
Click to collapse
what if i flash it with fastboot
---------- Post added at 01:07 PM ---------- Previous post was at 12:48 PM ----------
beacuse i just flashed it with fastboot and its not booting
waiting for 10 mints
recovery.img error
sayannayas said:
MICROMAX A65 ROOTED!!
Finally rooted my Micromax A65.Follow the guide carefully to avoid mistakes.I am not responsible for any physcial/logical damage to you and your device .
Thanks to authors and their posts
http://forum.xda-developers.com/showthread.php?t=2165554 ElectronikHeart(Guru of spreadtrum)
http://forum.xda-developers.com/showthread.php?p=42693514#post42693514 Yekdall (confirming me unlocking the boot.img is key)
http://forum.xda-developers.com/showthread.php?p=42776196#post42776196 Intex12345(calibartion tabs needs to be unckecked in RD)
http://whiteboard.ping.se/Android/Rooting (for unlocking the boot.img)
Foreground
A Chaina rebranned phone
A fastboot mode
A useless recovery mode
A locked boot.img (thats why even chmod or simply pushing a su will not root the phone)
A IMEI number(which if you mess up after flashing,you will not get any radio signals)
1)))First Unlock the Boot IMG
You need to tamper permssion after extracting the boot.img for this.No worry guys i have already done that for you .Just download the below file
http://www.mediafire.com/download/1c6r9cu9iwc3769/boot.zip
Now a bit critical part,read carefully .This unlocked image needed to be NAND flashed to your device.For that you need research download and firmware pac file.
Download this to files from the below links
http://forum.gsmhosting.com/vbb/f811/guide-all-micromax-root-clockworkrecovery-1627895/
(pac file,driver,research download all included)
<IT WILL ONLY WORK IN 32 BIT WINDOWS XP,VM ALSO FINE>
Download this drivers and install,after successfull installtion you will have(under device manager)
1.ABD inteface
2.two COM ports
3.two emulators
If any of this having yellow sign it will not work.
Open research download
click on first button and load pac file
click on second button change baudrate to 115200,in calibaration tab uncheck all.
For BOOT_IMG option browse and select the unlockedboot.img that you downloaded now.
plugin the usb cable(DONT plugin the phone now)
click on play button
PRESS & HOLD VOLUME UP KEY and insert the usb cable,dont release the key.
Download should starts within 3 secs.If it doesnt then check the drivers carefully or reply to this thread with failuers.
Once done unplugg your phone and remove battery for 3 second
Reinsert battery and restart your phone.
YES!! you have sucessfully unlocked the boot.img
2)))WiseMen Backup!!
First thing you should do before any tweaking and twisting save your back!!.Install CMW using the below method straight away and save your back.
1.Download .andriod.zip,extract it and save it under C:\Users\<computer name>\<paste it here>
http://www.mediafire.com/download/ga5tk2h89m41ddk/.android.zip
2.From your phone got to application-->developer option-->enable usb debugging
3.Now plugin your phone through micro usb cable.
4.Download this zip ,extract and place in under c:/<paste it here>
http://www.mediafire.com/download/s2as5grqceqtqq3/Android_Multi_tool.zip
5.Open a command prompt type
Code:
cd C:\Android Multi tool
C:\Android Multi tool>fastboot devices
20080823 fastboot
Note:you will NOT be able to proceed further if this doesnt shows up.Double check the andriod.zip has adb_usb.ini file.
Now we will flash a custom recovery image in fastboot mode.REMEMBER,PROBABILITY OF BRICKING IS MINIMUM AS I HAVE ALREADY DONE ALL THE TEST FOR YOU GUYS !!!.STILL IF ANYTHING GOES WRONG DONT PANIC,JUST FLASH A FIRMWARE AS MENTIONED ABOVE(point 1) EVENIF YOUR PHONE IS TOTALLY DEAD .
Code:
C:\Android Multi tool>fastboot flash recovery recovery.img
sending 'recovery' (10240 KB)...
OKAY [ 10.487s]
writing 'recovery'...
OKAY [ 3.425s]
finished. total time: 13.918s
7.Reboot your phone.
8.Now got to CMW using Volume up + power button and do a backup.
3))Push superuser zip & ROOT!!!
This the easiest step among all of them.Download the below file,put it under sdcard and flash it through CMW.
http://www.mediafire.com/download/t55b6ebzvx9yf1f/update.zip
THATS IT you are rooted!!!
REMEMBER,PROBABILITY OF BRICKING IS MINIMUM AS I HAVE ALREADY DONE ALL THE TEST FOR YOU GUYS !!!.STILL IF ANYTHING GOES WRONG DONT PANIC,JUST FLASH A FIRMWARE AS MENTIONED ABOVE(point 1) EVENIF YOUR PHONE IS
TOTALLY DEAD .
Please hit thanks if i you find this useful.:good:
Click to expand...
Click to collapse
finally i rooted my cellphone thank u guys n thank u xda
sssomnath474 said:
what if i flash it with fastboot
---------- Post added at 01:07 PM ---------- Previous post was at 12:48 PM ----------
beacuse i just flashed it with fastboot and its not booting
waiting for 10 mints
Click to expand...
Click to collapse
You should not flash anything before you have unlocked the boot.img.It comes with a locked boot so flashing through fastboot may not work.
First thing that you should do now is stage up a windows xp with the drivers that i have linked here.connect your phone with research download and do a firmware flash.This will recovery your phone to its orginal state.Then follow my steps from the start(pls dont skip)
navi_5886 said:
i have done the same but when i go to recovery option it says cannot mount e:
Click to expand...
Click to collapse
you should have micro sd card,and it should be in fat32 formatted.Better if you backup your data in sdcard,format it with fat32 and then place only the update.zip
sayannayas said:
You should not flash anything before you have unlocked the boot.img.It comes with a locked boot so flashing through fastboot may not work.
First thing that you should do now is stage up a windows xp with the drivers that i have linked here.connect your phone with research download and do a firmware flash.This will recovery your phone to its orginal state.Then follow my steps from the start(pls dont skip)
Click to expand...
Click to collapse
ok downloading windows xp..good thing is i'm not scared
well do u have facebook id?
sssomnath474 said:
ok downloading windows xp..good thing is i'm not scared
well do u have facebook id?
Click to expand...
Click to collapse
Dont get me wrong but i think it is better to log your errors here as it might help others as well as me to correct the OP.
Once you have the setup use exact set of drivers and pac file that i linked in this thread.remember if you have a successful driver installation then you will have at least(under device manager)
2 new COM ports
2 emulators
I am working on capturing few snapshots or a demonstration guide,it will take time as i recently lost my bag-pack,will update with videos once i stage up.
sayannayas said:
Dont get me wrong but i think it is better to log your errors here as it might help others as well as me to correct the OP.
Once you have the setup use exact set of drivers and pac file that i linked in this thread.remember if you have a successful driver installation then you will have at least(under device manager)
2 new COM ports
2 emulators
I am working on capturing few snapshots or a demonstration guide,it will take time as i recently lost my bag-pack,will update with videos once i stage up.
Click to expand...
Click to collapse
thankx bro..it will help more if you give screenshots
sayannayas said:
Dont get me wrong but i think it is better to log your errors here as it might help others as well as me to correct the OP.
Once you have the setup use exact set of drivers and pac file that i linked in this thread.remember if you have a successful driver installation then you will have at least(under device manager)
2 new COM ports
2 emulators
I am working on capturing few snapshots or a demonstration guide,it will take time as i recently lost my bag-pack,will update with videos once i stage up.
Click to expand...
Click to collapse
need a help do i only check boot_img or i check all files?
sssomnath474 said:
need a help do i only check boot_img or i check all files?
Click to expand...
Click to collapse
check all files in main page,but for boot_img browse a select the unlocked boot.img that i have linked in this thread.The idea is to flash the unlocked boot.img instead of stock boot.img. Uncheck all in calibration page.Keep baudrate 115200
Also download the ppt that i just added.It may help you. Don't give up,setting the drivers will take trails & errors but i guarantee you the success
sssomnath474 said:
need a help do i only check boot_img or i check all files?
Click to expand...
Click to collapse
sucsessfully flashed with origianal system file..and one thing more it worked in windows 7 64 bit too
sssomnath474 said:
sucsessfully flashed with origianal system file..and one thing more it worked in windows 7 64 bit too
Click to expand...
Click to collapse
Great news buddy.If you have used my unlocked boot.img while flashing then rest of the steps will be a breeze to you.Install CWM and take a full back up.Then flash the update.zip,thats it.
sayannayas said:
Great news buddy.If you have used my unlocked boot.img while flashing then rest of the steps will be a breeze to you.Install CWM and take a full back up.Then flash the update.zip,thats it.
Click to expand...
Click to collapse
well thankx for boot image and help device is rooted
but this can be done in other way to
1.you can use windows 7(u have to boot it in testmood and run the research downloader in adminstor)
2.just use unlock root
thats it
thankx man.pls give ur facebook id
sssomnath474 said:
well thankx for boot image and help device is rooted
but this can be done in other way to
1.you can use windows 7(u have to boot it in testmood and run the research downloader in adminstor)
2.just use unlock root
thats it
thankx man.pls give ur facebook id
Click to expand...
Click to collapse
Mentioned your updates in OP.Hope you dont mind
sayannayas said:
Mentioned your updates in OP.Hope you dont mind
Click to expand...
Click to collapse
ok ok
well making some customizing themes in UOT cooked kitchen.hope it will work
sssomnath474 said:
ok ok
well making some customizing themes in UOT cooked kitchen.hope it will work
Click to expand...
Click to collapse
Wow! that will be really nice...hope you will share those with us
sayannayas said:
Wow! that will be really nice...hope you will share those with us
Click to expand...
Click to collapse
check it out
need pac file...!!!!
sssomnath474 said:
thankx bro..it will help more if you give screenshots
Click to expand...
Click to collapse
can anyone upload only pac file for mmx a65 !!!!! please......!!!!""
sssomnath474 said:
check it out
Click to expand...
Click to collapse
WOW looking nice...waiting for the release
Also if you are maintaining your own a65 thread for customs roms,suggest you to cross link with mine(vice versa) and keep track for both the threads
Since the last update tool LGTool should we not also use the tool to flash KDZ as usual anymore. So we have to do it this way. Thanks @ Cloudyfa The Mod note KDZ update instructions for the box. @ blueberry chucvnvn @ @ gts8003 @ xuanduc89 ... Cloudyfa said :: ↑ faulty LG FlashTool You can try to do it this way:
1.Download file: http://www.androidfilehost.com/?fid=23329332407577839 Cloudyfa said :: ↑
2. Delete the folder C: \ ProgramData \ LGMOBILEAX folder and replace it with LGMOBILEAX extract from the file.
3. Open file Windows/System32/Drivers/etc/hosts with Admin rights. Add the following lines: Code:127.0.0.1 csmg.lgmobile.com
4. Download firmware update tool: http://www.androidfilehost.com/?fid=23329332407577842
5. Download Small HTTP
Server: http://www.androidfilehost.com/?fid=23329332407577847
6. Http.exe run before running LGFlashtool
7. Take steps up KDZ or TOT as normal or do. * 1 However, some anti-virus software will detect this soft mistaken, to allow it, and decided to spend it is up to you ok. Click to expand .. . SOURCE LG VIETNAM
How to modify the host file
1. Click Start -> All Programs -> Accessories
2. Right click Notepad and select Run as administrator
3. Click Continue on the "Windows needs your permission" UAC window.
4. When Notepad opens Click File -> Open
5. In the filename field type C:\Windows\System32\Drivers\etc\hosts
6. Click Open
I always get "Battery Level to Low" but my phone is even charged, dont know what i can do.
and when i use kdz_fw_upd i always get "extract file error"
Does someone knows what to do?
bricked my phone after updated my rooted e986 OTA. now i want to restore it back to stock.
Does the phone charge when it is in the cwm recovery?
Thanks bro! you are my life saver. Im deciding to go down to LG service centre tomorrow due to bad flash and now follow your steps, im able to restore back to factory!! Thanks again.
basicone1 said:
I always get "Battery Level to Low" but my phone is even charged, dont know what i can do.
and when i use kdz_fw_upd i always get "extract file error"
Does someone knows what to do?
bricked my phone after updated my rooted e986 OTA. now i want to restore it back to stock.
Does the phone charge when it is in the cwm recovery?
Click to expand...
Click to collapse
try uninstalling everything then install again everything or flash it using another computer
kongming said:
Thanks bro! you are my life saver. Im deciding to go down to LG service centre tomorrow due to bad flash and now follow your steps, im able to restore back to factory!! Thanks again.
Click to expand...
Click to collapse
no problem glad to help
Mr.Gabo said:
try uninstalling everything then install again everything or flash it using another computer
Click to expand...
Click to collapse
tried it on 3 different computers... so i dont think thats the problem
basicone1 said:
tried it on 3 different computers... so i dont think thats the problem
Click to expand...
Click to collapse
try flashing using tot file
I selected "cdma" at "select type" in the left corner of the R&D test tool window. Then the option CSE web upgrade test button appears, Clicked on this and no low battery warning this time. Phone is back to live (F240S)! Flashed the v20c 4.4.2 file for F240S.
Hello everybody, so I noticed a lot of people struggling with marshmallow + autorec hard bricks (symptoms: no download mode, no recovery, black screen)
Just to make sure: I'm not responsible for any damages done. This worked for me perfectly, should work for you too. Use it only if you bricked D855 30B!!! (Marshmallow)
Here's what you have to do to fix that:
First follow this amazing guide by senior member l33tlinuxh4x0r, big thanks to him. ---> LINK TO GUIDE
Important stuff: You need to install qualcomm drivers (windows 8, 10 users need to disable driver signature enforcement), you need to short the circuit of your phone, like it's shown in that guide, by shorting it correctly and plugging it in you immediately get connection (keep note of that, there's no need to wait for something, no sound - redo.)
Instead of extracting tot, like it's shown there, use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go.
DOWNLOAD HERE
Didn't know where to upload, so sorry for using this abomination
hi...please help~
catercousin said:
Hello everybody, so I noticed a lot of people struggling with marshmallow + autorec hard bricks (symptoms: no download mode, no recovery, black screen)
Just to make sure: I'm not responsible for any damages done. This worked for me perfectly, should work for you too. Use it only if you bricked D855 30B!!! (Marshmallow)
Here's what you have to do to fix that:
First follow this amazing guide by senior member l33tlinuxh4x0r, big thanks to him. ---> LINK TO GUIDE
Important stuff: You need to install qualcomm drivers (windows 8, 10 users need to disable driver signature enforcement), you need to short the circuit of your phone, like it's shown in that guide, by shorting it correctly and plugging it in you immediately get connection (keep note of that, there's no need to wait for something, no sound - redo.)
Instead of extracting tot, like it's shown there, use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go.
DOWNLOAD HERE
Didn't know where to upload, so sorry for using this abomination
Click to expand...
Click to collapse
i don't get what the meaning "use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go. "
can u explain how to done this step???
is this hard brick the result of using the Autorec MM or the old Lollipop one?
shun95 said:
i don't get what the meaning "use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go. "
can u explain how to done this step???
Click to expand...
Click to collapse
Select the attached download folder as "Target DIR" in the application, it will load the files and let you flash them like it's shown in the tutorial
Broloff said:
is this hard brick the result of using the Autorec MM or the old Lollipop one?
Click to expand...
Click to collapse
The Lollipop one
Hi thank you for this post
catercousin said:
Hello everybody, so I noticed a lot of people struggling with marshmallow + autorec hard bricks (symptoms: no download mode, no recovery, black screen)
Just to make sure: I'm not responsible for any damages done. This worked for me perfectly, should work for you too. Use it only if you bricked D855 30B!!! (Marshmallow)
Here's what you have to do to fix that:
First follow this amazing guide by senior member l33tlinuxh4x0r, big thanks to him. ---> LINK TO GUIDE
Important stuff: You need to install qualcomm drivers (windows 8, 10 users need to disable driver signature enforcement), you need to short the circuit of your phone, like it's shown in that guide, by shorting it correctly and plugging it in you immediately get connection (keep note of that, there's no need to wait for something, no sound - redo.)
Instead of extracting tot, like it's shown there, use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go.
DOWNLOAD HERE
Didn't know where to upload, so sorry for using this abomination
Click to expand...
Click to collapse
I've the same problem as you describe here.After I upgraded g3 to marshmallow I applied autorec and my device became hard brick.now my phone under com ports as Qualcomm 9008.
from this point I'm confused that which way to go the first your description 'Instead of extracting tot, like it's shown there, use attached files (target Dir)', Then again, flash them like it's shown in the tutorial'',the second tot file of the rom that we were running. (not older not newer same version).The first way I did not understand attached files where are they ?
if I follow the second way how can I find tot of my rom D855 30B!!! (Marshmallow)?
thank you waiting your help
Instead of tot you use the files from the download link in my post since you don't need to extract tot now, just mark that folder in "target dir" and follow the second guilde, as you call it. Good luck!
Help
catercousin said:
Hello everybody, so I noticed a lot of people struggling with marshmallow + autorec hard bricks (symptoms: no download mode, no recovery, black screen)
Just to make sure: I'm not responsible for any damages done. This worked for me perfectly, should work for you too. Use it only if you bricked D855 30B!!! (Marshmallow)
Here's what you have to do to fix that:
First follow this amazing guide by senior member l33tlinuxh4x0r, big thanks to him. ---> LINK TO GUIDE
Important stuff: You need to install qualcomm drivers (windows 8, 10 users need to disable driver signature enforcement), you need to short the circuit of your phone, like it's shown in that guide, by shorting it correctly and plugging it in you immediately get connection (keep note of that, there's no need to wait for something, no sound - redo.)
Instead of extracting tot, like it's shown there, use attached files (target Dir). Then again, flash them like it's shown in the tutorial. You should be good to go.
DOWNLOAD HERE
Didn't know where to upload, so sorry for using this abomination
Click to expand...
Click to collapse
The link is DEAD...
Maybe someone can reupload? I messed up and didn't save it in my computer, didn't think I'd need it anymore. Oops.. Or create them yourself
You need do extract .kdz, then .dz,
use this guide to create partition.txt
http://forum.xda-developers.com/lg-g2/general/how-to-create-partition-txt-file-kdz-t3109859
and rename files to ****.mbn
i just had my phone back to normal after marshmallow autorec brick
Get the right tools from scamex only..
U going to need :
Qdloader hs-usb driver for your pc 32/64bit
Install it
Then get smart boot diagnostic tool
Along that also get ap-chip dll and att
Then extract it the ap folder inside smart boot diagnostic tool
Get document to shows how to flash a "dead boot"
Then run thr smart boot diagnostic tool
Then follow instruction from the document and pay attention on page 14, 15 & 16
After recovering qfprom anti-roolback issue.
Your phone should be back to normal as before the autorec root hardbrick
catercousin said:
Maybe someone can reupload? I messed up and didn't save it in my computer, didn't think I'd need it anymore. Oops.. Or create them yourself
You need do extract .kdz, then .dz,
use this guide to create partition.txt
http://forum.xda-developers.com/lg-g2/general/how-to-create-partition-txt-file-kdz-t3109859
and rename files to ****.mbn
Click to expand...
Click to collapse
hey, the guide from the link is gone. do you happen to remember how to get partition.txt from .kdz ...or do you have one?
Hey!
Can anyone reupload the files from the OP?
Thanks!
Link is dead, can someone reupload the files please!?
unbelieveable.
every single link is dead for this
GET DROPBOX.
shoaibiftekhar said:
hey, the guide from the link is gone. do you happen to remember how to get partition.txt from .kdz ...or do you have one?
Click to expand...
Click to collapse
Still the case.
Could anyone help, please?
I found a guide to create "partition.txt" (maybe a copy the original guide here) but that's for the G2.
Any help is greatly appreciated :crying:
Hello!
I tried to update my Vodafone Branded G4 with the europe not branded version H81520g_00_0720.kdz
The problem ist i just get "error code = 0x2000, invalid command response" from the LGUP software and everytime i start the phone it is in firmware update mode.
Any idea how to fix this?
Greetings
I got this too as I tried to install H81520o_00_0310.kdz then I thought that it is maybe related to the brand. So I download your kdz file and then it was working.
So I would guess try another number is the best what you can do. I believe it is because of selection of "upgrade". If you have a tot file for refurbish, then maybe another is working, but I didn't do this yet.
Probably the problem is the DLL.
Extract the DLL from the KDZ (the one you want to flash) and replace it with the one you have in LGUP (path; C:/Program files/LG Electronics/LGUP/Model/8992).
the_naxhoo said:
Probably the problem is the DLL.
Extract the DLL from the KDZ (the one you want to flash) and replace it with the one you have in LGUP (path; C:/Program files/LG Electronics/LGUP/Model/8992).
Click to expand...
Click to collapse
i have the same problem2.
all the kdz that i download not come with any dll files just a 1.73 gb one file size.
kobisa25 said:
i have the same problem2.
all the kdz that i download not come with any dll files just a 1.73 gb one file size.
Click to expand...
Click to collapse
you must extract it from the KDZ with this tool: Click Here
the_naxhoo said:
you must extract it from the KDZ with this tool: Click Here
Click to expand...
Click to collapse
hi so i extract the kdz from LGExtract&7za& manuall tool& when i use winrar to extract its tell me no archive found i try also in winzip software. do you have any idea what else 2do?
thank you.
You can also try the codefire dll: http://downloads.codefi.re/autoprime/LG/LG_G4
( Download and rename LGFLASH_LG_G4_CODEFIRE.dll )
sfX
GOT IT!
the_naxhoo said:
you must extract it from the KDZ with this tool: Click Here
Click to expand...
Click to collapse
so after a long long search and dosents off error i succeeded
i find the currect kdz ISRAEL one and from it i EXTRACT it with WindowsLGFirmwareExtract-1.2.5.0-Release dll file and downgraded to lollipop 5.5 only with this dll file i make it after i try a few rom stocks that work with the dll.
i want to thank you you direct me to the right way:good:
Hi,
I have LG H811 (T-Mobile) Variant. I receive error from LGUP everytime I try to flash this ROM=h81120x_00_1108.kdz
My LGUP shows COM =COM3 and Version=H81120v
The error is thrown at 9%
Nothing working for me I am very frustrated!!!
PLEASE SOMEBODY HELP ME!
Stuck with LG G4 (H81520i)
Same for me but with LG H81520i. I tried to flash these ROM* with their specific .dll that I extracted thanks to WindowsLGFirmwareExtract-1.2.5.0-Release. Always get "error code = 0x2000, invalid command response" from LGUP. The error is thrown at 16% on the computer, but at 7% on the phone. Now, I'm stuck in download mode. I also tried to change the COM port number, doesn't change anything.
*Europe General H81510B_00.kdz ; Europe OPEN H81510D.kdz ; H81510D_00.kdz ; H81520i_00_0922.kdz ; SEA H81510B.kdz
Only one ROM above matches the LG H81520i (the fourth one).
Informations about my (ex-)android firmware :
- Android version : 6.0 (Marshmallow)
- Kernel version : 3.10.84
- Software version : V20-SEA-XX
PS : H81520i is what is written on the LGUP software
______________________________________________________________________________
I found a solution (after several hours)
Uninstall all your LG softwares (except LG Bridge or others LG backup softwares) and go to 'C:\Program Files (x86)\LG Electronics\' to delete all folders and files.
Go to this link and click on "Download all". Extract the file and follow the instructions :
1) Install "LGMobileSupportTool.exe"
2) Install "LGMobileDriver_WHQL_Ver_4.2.0.exe"
3) Install "LGUP_Install_Ver_1_14_3.msi"
4) Install "LGUP_8994_DLL_Ver_0_0_3_23.msi"
5) Move "LGUP_8994.dll" in the repertory 'C:\Program Files (x86)\LG Electronics\LGUP\model\8994'
6) Open "LGMobile Support Tool" and click on "Install USB driver." to the left
7) Select "LGH815" (or your model) et follow the drivers installation steps
8) Do step 5) again
9) Shut off your LG and plug it to your computer while pressing volume up in order to enter download mode
10) Unplug your LG and the battery
11) Open "LGUP" and close it
12) Do step 9 again (download mode)
13) Open "LGUP", select "UPGRADE" and go select your .kdz file (the ones in the file that you downloaded or another one you have)
14) Click on "Start" and DON'T TOUCH !!!!!!
Big thanks to the people of this reddit post and of this XDA thread
See above
Back To Stock ROM LG G4 H811 (T-Mobile)
LucasDupanne said:
________________________________________________________
First of all, I'm not allowed to post links as a new user , so I put them with spaces that you must delete :laugh: . Good luck !
Uninstall ALL your softwares (except LG Bridge or others LG backup softwares) and go to 'C:\Program Files (x86)\LG Electronics\' to delete all folders and files.
Go to this link ( ht tps : / / ya di . sk /d / KIG5F8 2jmXcUR ) and click on "Download all". After downloading the file, extract it and follow the instructions :
1) Install "LGMobileSupportTool.exe"
2) Install "LGMobileDriver_WHQL_Ver_4.2.0.exe"
3) Install "LGUP_Install_Ver_1_14_3.msi"
4) Install "LGUP_8994_DLL_Ver_0_0_3_23.msi"
5) Move "LGUP_8994.dll" in the repertory 'C:\Program Files (x86)\LG Electronics\LGUP\model\8994'
6) Open "LGMobile Support Tool" and click on "Install USB driver." to the left
7) Select "LGH815" et follow the drivers installation steps
8) Do step 5) again
9) Shut off your LG and plug it to your computer while pressing volume up in order to enter download mode
10) Unplug your LG and the battery
11) Open "LGUP" and shut it
12) Do again step 8 (download mode)
13) Open "LGUP", select "UPGRADE" and go select your .kdz file (your one or the ones in the file that you downloaded)
14) Click on "Start" and DON'T TOUCH !!!!!!
==>> thanks to ' ht tps : / / www .reddit . com /r/lgg4/comments/7anayg/downgraded_from_n_to_mm_and_stuck_in_download / ' post
A french man of 15 years that thanks Lobster_Johnson123 very very much.
PS : Sorry, my english is bad And let me know !!! :fingers-crossed:
Click to expand...
Click to collapse
Thanks Lucas for your time and help. It didn't work for me. I flashed another ROM named H811V20r_00_0111.kdz and it worked like a charm and it's tested on so many devices afterwards which worked fine without a single issue.
Here is the link to the ROM: https://lg-roms.com/official-firmware/LG G4-LGH811VK/H811V20r_00_0111/
Thanks for the help though.
androhead said:
Thanks Lucas for your time and help. It didn't work for me. I flashed another ROM named H811V20r_00_0111.kdz and it worked like a charm and it's tested on so many devices afterwards which worked fine without a single issue.
Here is the link to the ROM:
Thanks for the help though.
Click to expand...
Click to collapse
Happy it worked an other way for you !
i had working H815 version 29A nougat installed but for some reason
( nougat restarting issue ) during flashing H815 version 10d , after 9 percent same error comes , i tried by copying extracted dll from H815 v10d kdz in the LGUP (8994 folder) but nothing works for me,
please friends come to resolve my issue. waiting for reply from xda experts
Sanaullahshuaib said:
i had working H815 version 29A nougat installed but for some reason
( nougat restarting issue ) during flashing H815 version 10d , after 9 percent same error comes , i tried by copying extracted dll from H815 v10d kdz in the LGUP (8994 folder) but nothing works for me,
please friends come to resolve my issue. waiting for reply from xda experts
Click to expand...
Click to collapse
You need H81520p.kdz to downgrade from Nougat!
You can download from here: https://www.4shared.com/file/hfyqh6iEfi/H81520p_00_0314.html
Can also see here if you need more files: https://forum.xda-developers.com/showpost.php?p=76571471&postcount=23
Okay I'll try this but please tell me that
I have to copy lgup_8994.dll from H81520p or use original dll which is installed with the LGUP 8994 installer???
Sanaullahshuaib said:
Okay I'll try this but please tell me that
I have to copy lgup_8994.dll from H81520p or use original dll which is installed with the LGUP 8994 installer???
Click to expand...
Click to collapse
After install everything, replace the one in "C:\Program Files (x86)\LG Electronics\LGUP\model\8994" by the given one (or extract from the H81520p.kdz file).
See on the picture how your phone should be detected in "Device Manager":
http://i1376.photobucket.com/albums/ah39/RuedasLocas/Varios/Sem Tiacutetulo_zpsrrscdqov.jpg
H815v20p flashed correctly but mobile in boot-loop then i back installed H815v10d the original but also restarting
xda experts???
whats the issue in your mind experts XDA???
Sanaullahshuaib said:
H815v20p flashed correctly but mobile in boot-loop then i back installed H815v10d the original but also restarting
xda experts???
whats the issue in your mind experts XDA???
Click to expand...
Click to collapse
You first start your phone with any sim or sd card?
Try to flash it again with the v20p and restart it without any card on it.
If it doesn't solve the problem, try a v10a. Maybe it works and you can upgrade starting from there.
Good luck!
now again I tried H815v29A so it installed after the installation of old original version , now please tell the method of rooting Nougat on H815v29A urgently XDA experts???
also Twrp not installing on H815v29A which was working on marshmallow/////
experts reply???
Please, where can I find ME372CG files for xFSTK?
I want to restore bootloader of my ME372CG tablet.
I follow these instructions, which are for FE170CG:
https://forum.xda-developers.com/android/help/asus-fonpad-7-fe170cg-bricked-stuck-t3740819
But I did not find ME372CG files for xFSTK.
So I took them from official Asus ME372CG firmware (from UL-K00E-WW-7.6.0.0-user.zip).
I found different file names in ifwi folder and I am not sure, which to use fo xFSTK:
dnx_fwr_ctp_???.bin
ifwi_ctp_???.bin
CLVP_CSAB_FWR_DnX_20.29.bin
ME372CG_32_IFWI_v54.57_CSAB_PROD.bin
I could not find any Softfuse file either.
Most probably I do not have the correct files, because xFSTK download does not work.
The file names, which I used, and the result from xFSTK can be found here:
https://www.dropbox.com/s/cz8imzdrs1r551r/xFSTK_ME372CG files.JPG?dl=0
Where can I find the correct files for xFSTK?
Thank you very much.
Greetings from Slovakia
Juraj
---
Cause of malfunction:
My tablet reported some kind of UI error, so I restarted it (still within Android),
but it never started again. It just vibrates when switching on, always black screen (only almost unnoticeable flash of light on LCD, during switching on). The battery is full - I measured it.
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Teddy Lo said:
Use this file, run as Administrator ME372CG Debrick.bat and connect your device.
https://gofile.io/d/P6Ja57
After that flash this raw file with asus flash tool and make sure to select right model name.
http://www.mediafire.com/file/fhtkb..._V11.2.3.33-raw_2015_SmartPhones.How.zip/file
Good Luck
Click to expand...
Click to collapse
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
sid.1375 said:
Hey Teddy, The link has been expired! Can you upload it again?
I need FW DnX, IFWI, OS DnX for fonepad 7 ME372CG (K00e)
Click to expand...
Click to collapse
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
jurajhotovy said:
Hi, I received some suggestions from Teddy, but it did not work for me.
(I re-uploaded the files to Dropbox, so the links should work):
1. Download this zip: https://www.dropbox.com/s/1s5i85hd22yqlct/CSC_ME372CG_Debrick.7z?dl=0
2. Extract with 7-zip on your Desktop
3. Open extracted CSC_ME372CG_Debrick file ---> Right click on ME372CG Debrick.bat left click on Run as Administrator. And it should look like this:
https://www.dropbox.com/s/e3yulpxt70rn6ly/non-Administrator ME372CG Debrick.bat.png?dl=0
If that doesn't show up install this minimal adb and fastboot command
https://www.dropbox.com/s/zgr1ljdm13owlrs/minimal_adb_fastboot_v1.4.1_setup.exe?dl=0
Here is tutorial how to install:
https://forum.xda-developers.com/showthread.php?t=2317790
4. If the tool doesn't recognise your device press VOL + or VOl - and connect your device with pc while you are holding one of volume buttons.....
===
After I informed Teddy that it does not work for me,
he suggested this:
See this tutorial for another device to get the point, reinstall drivers and try again debrick files. Softfuse file I can't find for your device but with debrick.bat is trick for seconds I thing to get recognized to start flashing partition and firmware....
https://www.youtube.com/watch?v=xuD39TjQJGo
or buy package and download files for XFSTK.
https://easy-firmware.com/index.php?a=downloads&b=file&id=100391
(I have not bought those xFSTK files yet, but I will try it later this week and let you know.)
Juraj
Click to expand...
Click to collapse
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
sid.1375 said:
I tried that but it didn't work. Actually it's because we lost fastboot and droidboot.
About those xFSTK files, we can acquire them from rom (zip/raw). there is a zip file called "ifwi.zip" in the rom package.
I follow this tutorial to debrick it but I didn't make it:crying:
Click to expand...
Click to collapse
Hi
Finally, did you can find a solution for K00E?
miter8 said:
Hi
Finally, did you can find a solution for K00E?
Click to expand...
Click to collapse
Unfortunately no.
Sorry for the late response.