FOR DEVS AND USERS BEFORE FIGHT ME CLICK HERE!: https://forum.xda-developers.com/showpost.php?p=70362424&postcount=3
Code:
DISCLAIMER!!
I am not responsible in any way for anything that can be happen to your device when you flashing my kernels.You do so at your own risk!
Features
Anykernel:
- Anykernel2 zip for maximum compatibility with all ROMs, CrazyAquaKernel uses your existing ramdisk (Do NOT flash this over other custom kernels!You should only flash CrazyAquaKernel over the kernel that came with your ROM!!)
Toolchain:
UBERTC 4.9 Toolchain
CPU:
- governors:
crazyactive(my governor:balance governor for great battery life and performance based on interactive)
interactive
impulse
ondemand
smartmax
zzmoove
ondemandplus
pegasusq
nightmare
conservative
lionheart
powersave
userspace
yankactive
smartmax_eps
intellidemand
intelliactive
- MSM Limiter
- input boost
- state notifier
IO schedulers:
bfq
tripndroid
cfq
noop
deadline
fiops
row
sio
zen
vr
fifo
TCP congestion controls:
cubic
bic
westwood
htcp
highspeed
hybla
reno
bic
hybla
vegas
lp
yeah
illinois
scalable
- tcp congestion changed to Westwood
GPU:
- governors:
msm-adreno-tz
simple_ondemand
powersave,performance
userspace
cpubw_hwmon
msm_cpufreq
- Adreno idler
- simple gpu algorithm
Thermal control:
- Intelli thermal v2
Hotplug:
- Disabled MP Decision hotplug
- Enabled Bricked Hotplug
- Prevent wakelock when ambiend display disabled(misc control tab)
Sound:
- Faux sound
More:
- Kernel runs with SELinux permissive by default
- init.d support
- insecure kernel (adb has root privileges)
- fast charge
- pvs level info
- Kcal v2
- Frandom support
- Disabled Arch Power
- CRC Check Disabled
- Gentle Fair Sleepers (Disabled by default)
- Enabled All Suspend and Idle Modes
- Power Suspend Mode/State
- Dynamic filesystem read-ahead
- A lot improvments
- A lot fixes
Download Link CrazyAquaKernel [AnyKernel]:https://www.androidfilehost.com/?fid=817550096634793333
Installation guide
Do NOT flash this over other custom kernels!
You should only flash CrazyAquaKernel over the kernel that came with your ROM!!
- Download Kernel from this thread
- Flash it with Recovery
[Wipe cache and Dalvik cache recommended]
- Then Reboot
Enjoy the CrazyAquaKernel !!!!
Credits
thx Showp1984
thx Faux123
thx Savoca
thx RenderBroken
thx Neobuddy
thx Myfluxi
thx FranciscoFranco
thx SultanXDA
thx osm0sis
thx ShinyShide
thx bhb27
thx Lord Boeffla
thx yank555
thx apb_axel
thx the devs where made the cm14 bootable and working
thx CrazyGamerGR yeh me
XDA:DevDB Information
CrazyAquaKernel, Kernel for the OnePlus One
Contributors
CrazyGamerGR
Source Code: https://github.com/CrazyGamerGR/CrazyAquaKernel-opo-los
Kernel Special Features:
Version Information
Status: Beta
Created 2017-08-17
Last Updated 2017-08-17
FAQ
Recommended app : Kernel Adiutor
changelogs
v1.0/17-08-17
- initial release
If u use zzmove governor disable all the hotplugs coz it use its own hotplug as anyone knows.
[Q]How i select profile from kernel tweaker app?
[A]You need to go in governor tunable-profile number and select the number of the profile from the list.
Zzmove profiles
1 ) Default -> will set governor defaults
2 )ybat -> Yank Battery -> a very good battery/performance balanced setting - DEV-NOTE: highly recommended!
3 )ybatext-> Yank Battery Extreme -> like yank battery but focus on battery saving
4 )zzbat-> ZaneZam Battery -> a more 'harsh' setting strictly focused on battery saving - DEV-NOTE: might give some lags!
5 )zzbatp -> ZaneZam Battery Plus -> NEW! reworked faster battery setting - DEV-NOTE: recommended too!
6 )zzopt -> ZaneZam Optimized -> balanced setting with no focus in any direction - DEV-NOTE: relict from back in the days, even though some people still like it!
7 )zzmod -> ZaneZam Moderate -> NEW! setting based on 'zzopt' which has mainly (but not strictly only!) 2 cores online
8 )zzperf -> ZaneZam Performance -> all you can get from zzmoove in terms of performance but still has the fast - down scaling/hotplugging behaving
9 )zzinz-> ZaneZam InZane -> NEW! based on performance with new insane scaling active. a new experience!
10 )zzgame-> ZaneZam Gaming -> NEW! based on performance with scaling block enabled to avoid cpu overheating during gameplay
reserve1
reserve2
You're back! Thanks for still contributing to bacon.
Mr.Ak said:
You're back! Thanks for still contributing to bacon.
Click to expand...
Click to collapse
I promised it where i will come back
Downloading
Minions_Army said:
Downloading
Click to expand...
Click to collapse
Cool^^
CrazyGamerGR said:
Cool^^
Click to expand...
Click to collapse
Performance is good
Minions_Army said:
Performance is good
Click to expand...
Click to collapse
Thx for feedback m8
Will it work with Sultan's N ROM ?
tamboli007 said:
Will it work with Sultan's N ROM ?
Click to expand...
Click to collapse
You can try m8 coz he use caf source but los work too
Sent from my iPhone using Tapatalk Pro
CrazyGamerGR said:
You can try m8 coz he use caf source but los work too
Click to expand...
Click to collapse
It's working fine:good:. Thanks
Edit :- camera doesn't work .
tamboli007 said:
It's working fine:good:. Thanks
Edit :- camera doesn't work .
Click to expand...
Click to collapse
It is rom problem coz i didn't added something for camera
He make changes for camera coz i used his rom on my op3,i need to do some changes to work correct with caf roms too
Sent from my iPhone using Tapatalk Pro
I hope u plan to support custom blobs too. OOS v2 (sultan) or OOS v3 instead of CM blobs
MrxSiN said:
I hope u plan to support custom blobs too. OOS v2 (sultan) or OOS v3 instead of CM blobs
Click to expand...
Click to collapse
Maybe soon m8
Sent from my iPhone using Tapatalk Pro
downloading.., btw., kernel auditor should be used to do the changes..?
murti52 said:
downloading.., btw., kernel auditor should be used to do the changes..?
Click to expand...
Click to collapse
Yeh i recommend it
this one won't work on this rom if it's AOSP?
https://forum.xda-developers.com/oneplus-one/development/rom-aospextended-rom-v3-1-t3547628
Yes, I'm a noob ......I can only flash rom's
I'm lost with all these versions: CAF LOS,CM, AOSP ..... special Camera HALs ....can someone explain what works on what ?
the AOSP rom is great but battery charging is superslow and cpu undervolting would also be great
I'm looking to get the best battery life rom without choppy interface
I never game on my OPO , just call,txt and internet.
any Rom /Kernel suggestions (or gouvernor settings)
Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
FOR DEVS AND USERS BEFORE FIGHT ME CLICK HERE!: https://forum.xda-developers.com/showpost.php?p=70362424&postcount=3
Code:
DISCLAIMER!!
I am not responsible in any way for anything that can be happen to your device when you flashing my kernels.You do so at your own risk!
Features
Anykernel:
- Anykernel2 zip for maximum compatibility with all ROMs, CrazySuperKernel uses your existing ramdisk (Do NOT flash this over other custom kernels!You should only flash CrazySuperKernel over the kernel that came with your ROM!!)
Kernel tweaker app:
- CrazySuperKernel Adiutor (need download it from downloads)
Toolchain:
DF 4.9 Toolchain [latest update]
CPU:
- governors:
crazyactive(my governor:balance governor for great battery life and performance based on interactive)
interactive
impulse
ondemand
smartmax
zzmoove
ondemandplus
pegasusq
nightmare
conservative
lionheart
powersave
userspace
yankactive
smartmax_eps
intellidemand
intelliactive
- MSM Limiter
- input boost
- state notifier
IO schedulers:
bfq
tripndroid
cfq
noop
deadline
fiops
row
sio
zen
vr
fifo
TCP congestion controls:
cubic
bic
westwood
htcp
highspeed
hybla
reno
bic
hybla
vegas
lp
yeah
illinois
scalable
- tcp congestion changed to Westwood
GPU:
- governors:
msm-adreno-tz
simple_ondemand
powersave,performance
userspace
cpubw_hwmon
msm_cpufreq
- Adreno idler
- simple gpu algorithm
Thermal control:
- Intelli thermal v2
Hotplug:
- Disabled MP Decision hotplug
- Enabled Bricked Hotplug
- Prevent wakelock when ambiend display disabled(misc control tab)
Sound:
- Faux sound updated and fixed
- Slimbus overclock
More:
- Kernel runs with SELinux permissive by default
- init.d support
- insecure kernel (adb has root privileges)
- fast charge
- pvs level info
- Kcal v2
- Frandom support
- Disabled Arch Power
- CRC Check Disabled
- Gentle Fair Sleepers (Disabled by default)
- Enabled All Suspend and Idle Modes
- Power Suspend Mode/State
- Dynamic filesystem read-ahead
- A lot improvments
- A lot fixes
Download Link CrazySuperKernel [AnyKernel]:https://www.androidfilehost.com/?w=files&flid=138590
Download Link CrazySuperKernelAdiutor[Updated]:https://www.androidfilehost.com/?w=files&flid=139961
Installation guide
Do NOT flash this over other custom kernels!
You should only flash CrazySuperKernel over the kernel that came with your ROM!!
- Download Kernel from this thread
- Flash it with Recovery
[Wipe cache and Dalvik cache recommended]
- Then Reboot
Enjoy the CrazySuperKernel !!!!
Credits
thx Showp1984
thx Faux123
thx Savoca
thx RenderBroken
thx Neobuddy
thx Myfluxi
thx FranciscoFranco
thx SultanXDA
thx osm0sis
thx ShinyShide
thx bhb27
thx Lord Boeffla
thx yank555
thx apb_axel
thx the devs where made the cm14 bootable and working
thx CrazyGamerGR yeh me
Donators
red5pade
XDA:DevDB Information
CrazySuperKernel, Kernel for the OnePlus One
Contributors
CrazyGamerGR
Source Code: https://github.com/CrazyGamerGR/CrazySuperKernel-CM14.1-OPO
Kernel Special Features: check the feature list
Version Information
Status: Stable
Created 2016-12-25
Last Updated 2016-12-25
FAQ
Recommended app : CrazySuperKernel Adiutor
changelogs
v1.0/24-12-16
- initial release
v2.0/27-12-16
- CrazySuperKernel Adiutor (included)
- Deleted Synapse
- added stable faux sound
- some anykernel fixes
v3.0/31-12-16
- added fast charge
- deleted included CSKAdiutor (need download it)
- many fixes
v4.0/02-01-17
- updated fast charge
- pvs level info
- some fixes
If u use zzmove governor disable all the hotplugs coz it use its own hotplug as anyone knows.
[Q]How i select profile from kernel tweaker app?
[A]You need to go in governor tunable-profile number and select the number of the profile from the list.
Zzmove profiles
1 ) Default -> will set governor defaults
2 )ybat -> Yank Battery -> a very good battery/performance balanced setting - DEV-NOTE: highly recommended!
3 )ybatext-> Yank Battery Extreme -> like yank battery but focus on battery saving
4 )zzbat-> ZaneZam Battery -> a more 'harsh' setting strictly focused on battery saving - DEV-NOTE: might give some lags!
5 )zzbatp -> ZaneZam Battery Plus -> NEW! reworked faster battery setting - DEV-NOTE: recommended too!
6 )zzopt -> ZaneZam Optimized -> balanced setting with no focus in any direction - DEV-NOTE: relict from back in the days, even though some people still like it!
7 )zzmod -> ZaneZam Moderate -> NEW! setting based on 'zzopt' which has mainly (but not strictly only!) 2 cores online
8 )zzperf -> ZaneZam Performance -> all you can get from zzmoove in terms of performance but still has the fast - down scaling/hotplugging behaving
9 )zzinz-> ZaneZam InZane -> NEW! based on performance with new insane scaling active. a new experience!
10 )zzgame-> ZaneZam Gaming -> NEW! based on performance with scaling block enabled to avoid cpu overheating during gameplay
reserve1
reserve2
More and more kernels
Thanks!
Support fast charge?
assassin0408 said:
Support fast charge?
Click to expand...
Click to collapse
I will add soon usb fast charge and maybe charge control.
Thanks and great job!
Bobbi lim said:
Thanks and great job!
Click to expand...
Click to collapse
Thx m8,new features coming soon.
Merry Christmas!!!!!
assassin0408 said:
Support fast charge?
Click to expand...
Click to collapse
U from galaxy s advance mate
pankspoo said:
U from galaxy s advance mate
Click to expand...
Click to collapse
Yes thats true.. S advance. How do you know me?
Hello, Merry Christmas, I installed this kernel but do not work 2 things:
1- installed the kernel, but when I open Synapse tells me: NO UCI DETECT
2-UKM installed 3.8.1, but the audio portion can not be configured, even if imposed different or custom profiles, the values remain the same, and the sound remains very low.
I apologize for my English, but I'm using a translator !!!
NeGriTa79 said:
Hello, Merry Christmas, I installed this kernel but do not work 2 things:
1- installed the kernel, but when I open Synapse tells me: NO UCI DETECT
2-UKM installed 3.8.1, but the audio portion can not be configured, even if imposed different or custom profiles, the values remain the same, and the sound remains very low.
I apologize for my English, but I'm using a translator !!!
Click to expand...
Click to collapse
The synapse after a reboot should work its created for this device with many new features,its not same with the old synapse.But after many problems from the synapse i will not continue it,the new builds will be include other kernel tweaker app.
CrazyGamerGR said:
The synapse after a reboot should work its created for this device with many new features,its not same with the old synapse.But after many problems from the synapse i will not continue it,the new builds will be include other kernel tweaker app.
Click to expand...
Click to collapse
I downloaded from Synapse PlayStore ... several times ... but it does not go ... to make it work I had to install UKM 3.8.1 ... Where can I find UKM updated for your kernel?
NeGriTa79 said:
I downloaded from Synapse PlayStore ... several times ... but it does not go ... to make it work I had to install UKM 3.8.1 ... Where can I find UKM updated for your kernel?
Click to expand...
Click to collapse
It is included,you just instal synapse app from playstore and it work,you use RR?
CrazyGamerGR said:
It is included,you just instal synapse app from playstore and it work,you use RR?
Click to expand...
Click to collapse
If I do not install UKM not start me Synapse. I mount the NuclearRom 7.1.1 Version 1.2.0 BETA
The audio is very low and you can not configure it nessn so ... I tried to install Faux Sound Control ... But it does not change anything!
NeGriTa79 said:
If I do not install UKM not start me Synapse. I mount the NuclearRom 7.1.1 Version 1.2.0 BETA
The audio is very low and you can not configure it nessn so ... I tried to install Faux Sound Control ... But it does not change anything!
Click to expand...
Click to collapse
Its modded faux sound,tomorrow i ll have my new kernel tweaker app ready to fix all these problems from the Synapse.
CrazyGamerGR said:
Its modded faux sound,tomorrow i ll have my new kernel tweaker app ready to fix all these problems from the Synapse.
Click to expand...
Click to collapse
Very Thanks
Inviato dal mio A0001 utilizzando Tapatalk
FOR DEVS AND USERS BEFORE FIGHT ME CLICK HERE!: https://forum.xda-developers.com/showpost.php?p=70362424&postcount=3
Code:
DISCLAIMER!!
I am not responsible in any way for anything that can be happen to your device when you flashing my kernels.You do so at your own risk!
Features
Anykernel:
- Anykernel2 zip for maximum compatibility with all ROMs, CrazyAquaKernel uses your existing ramdisk (Do NOT flash this over other custom kernels!You should only flash CrazyAquarKernel over the kernel that came with your ROM!!)
Toolchain:
UBERTC 4.9 Toolchain
CPU:
- governors:
crazyactive(my governor:balance governor for great battery life and performance based on interactive)
interactive
impulse
ondemand
smartmax
zzmoove
ondemandplus
pegasusq
nightmare
conservative
lionheart
powersave
userspace
yankactive
smartmax_eps
intellidemand
intelliactive
- MSM Limiter
- input boost
- state notifier
IO schedulers:
bfq
tripndroid
cfq
noop
deadline
fiops
row
sio
zen
vr
fifo
TCP congestion controls:
cubic
bic
westwood
htcp
highspeed
hybla
reno
bic
hybla
vegas
lp
yeah
illinois
scalable
- tcp congestion changed to Westwood
GPU:
- governors:
msm-adreno-tz
simple_ondemand
powersave,performance
userspace
cpubw_hwmon
msm_cpufreq
- Adreno idler
- simple gpu algorithm
Thermal control:
- Intelli thermal v2
Hotplug:
- Disabled MP Decision hotplug
- Enabled Bricked Hotplug
- Prevent wakelock when ambiend display disabled(misc control tab)
Sound:
- Faux sound
More:
- Kernel runs with SELinux permissive by default
- init.d support
- fast charge
- pvs level info
- insecure kernel (adb has root privileges)
- Frandom support
- Disabled Arch Power
- CRC Check Disabled
- Gentle Fair Sleepers (Disabled by default)
- Enabled All Suspend and Idle Modes
- Power Suspend Mode/State
- Dynamic filesystem read-ahead
- A lot improvments
- A lot fixes
Supported Variants:
D800
D801
D802/5/6
F320
L01F
LS980
VS980
LGL22
Download Link CrazyAquaKernel [AnyKernel]:https://www.androidfilehost.com/?w=files&flid=207696
Installation guide
Do NOT flash this over other custom kernels!
You should only flash CrazyAquarKernel over the kernel that came with your ROM!!
- Download Kernel from this thread
- Flash it with Recovery
[Wipe cache and Dalvik cache recommended]
- Then Reboot
Enjoy the CrazyAquaKernel !!!!
Credits
thx Showp1984
thx Faux123
thx dorimanx
thx Savoca
thx RenderBroken
thx Neobuddy
thx Myfluxi
thx FranciscoFranco
thx SultanXDA
thx osm0sis
thx ShinyShide
thx bhb27
thx Lord Boeffla
thx yank555
thx apb_axel
thx the devs where made the cm14 bootable and working
thx CrazyGamerGR yeh me
XDA:DevDB Information
CrazyAquaKernel, Kernel for the LG G2
Contributors
CrazyGamerGR
Source Code: https://github.com/CrazyGamerGR/CrazyAquaKernel-g2-los
Kernel Special Features:
Version Information
Status: Beta
Created 2017-08-17
Last Updated 2017-08-17
FAQ
Recommended app : Kernel Adiutor
changelogs
v1.0/17-08-17
- initial release
If u use zzmove governor disable all the hotplugs coz it use its own hotplug as anyone knows.
[Q]How i select profile from kernel tweaker app?
[A]You need to go in governor tunable-profile number and select the number of the profile from the list
Zzmove profiles
1 ) Default -> will set governor defaults
2 )ybat -> Yank Battery -> a very good battery/performance balanced setting - DEV-NOTE: highly recommended!
3 )ybatext-> Yank Battery Extreme -> like yank battery but focus on battery saving
4 )zzbat-> ZaneZam Battery -> a more 'harsh' setting strictly focused on battery saving - DEV-NOTE: might give some lags!
5 )zzbatp -> ZaneZam Battery Plus -> NEW! reworked faster battery setting - DEV-NOTE: recommended too!
6 )zzopt -> ZaneZam Optimized -> balanced setting with no focus in any direction - DEV-NOTE: relict from back in the days, even though some people still like it!
7 )zzmod -> ZaneZam Moderate -> NEW! setting based on 'zzopt' which has mainly (but not strictly only!) 2 cores online
8 )zzperf -> ZaneZam Performance -> all you can get from zzmoove in terms of performance but still has the fast - down scaling/hotplugging behaving
9 )zzinz-> ZaneZam InZane -> NEW! based on performance with new insane scaling active. a new experience!
10 )zzgame-> ZaneZam Gaming -> NEW! based on performance with scaling block enabled to avoid cpu overheating during gameplay
reserve1
reserve2
reserve3
Great thanks
So I flashed it on my D802 with CrDroid 3.6 (it's LOS based). I wiped caches also.
In Kernel Auditor I set zzmove +ybat, disabled hotplugs, set this all to run on boot and now everything has a lag.
Unlocking screen, starting apps, even keyboard (it's very hard to write this post cause the lag).
Pros (for me):
It booted.
Sound tab in Kernel Auditor.
I'll try to play with different governors and if it wont help I will go back to my backup and standard CrDroid kernel.
BTW: Thanks for your work!
MarekAG said:
So I flashed it on my D802 with CrDroid 3.6 (it's LOS based). I wiped caches also.
In Kernel Auditor I set zzmove +ybat, disabled hotplugs, set this all to run on boot and now everything has a lag.
Unlocking screen, starting apps, even keyboard (it's very hard to write this post cause the lag).
Pros (for me):
It booted.
Sound tab in Kernel Auditor.
I'll try to play with different governors and if it wont help I will go back to my backup and standard CrDroid kernel.
BTW: Thanks for your work!
Click to expand...
Click to collapse
It is a little laggy coz it use bricked and mpdecsion is fully disabled,i disabled full for amazing battery life and not all time on all the cores ,now i try tweak the hotplug for more performance
Bootloop on F320
F320 hasn't official rom so I was using d802(devices check removed)LOS 14.1 and lambda kernel f320 Please check it thanks
eggimong said:
F320 hasn't official rom so I was using d802(devices check removed)LOS 14.1 and lambda kernel f320 Please check it thanks
Click to expand...
Click to collapse
I have f320 kernel, now for rom i can't do something coz i don't have time
Sent from my iPhone using Tapatalk Pro
Dev sir, could you tell me the difference between aqua and super version?
Genie's said:
Dev sir, could you tell me the difference between aqua and super version?
Click to expand...
Click to collapse
More updated and clean kernel
Thanks for continuing the work
Enviado desde mi LG-D802 mediante Tapatalk
Which application to customize?
omer.bulbul144 said:
Which application to customize?
Click to expand...
Click to collapse
I recommend kernel adiutor
CrazyGamerGR said:
I recommend kernel adiutor
Click to expand...
Click to collapse
Whichever?
https://play.google.com/store/apps/details?id=com.grarak.kerneladiutor&hl=tr
https://forum.xda-developers.com/android/apps-games/kernel-adiutor-mod-singularity-kernel-t3333549
omer.bulbul144 said:
Whichever?
https://play.google.com/store/apps/details?id=com.grarak.kerneladiutor&hl=tr
https://forum.xda-developers.com/android/apps-games/kernel-adiutor-mod-singularity-kernel-t3333549
Click to expand...
Click to collapse
Up to you m8,maybe soon i ll add a kernel tweaker in my kernels
Sent from my iPhone using Tapatalk Pro
Works XOSP?
Enviado desde mi LG-D802 mediante Tapatalk
slipknot31 said:
Works XOSP?
Enviado desde mi LG-D802 mediante Tapatalk
Click to expand...
Click to collapse
It work with every lineageos based rom
Sent from my iPhone using Tapatalk Pro
DISCLAIMER
I will not be held responsible for anything that happens to your device after flashing this kernel. If you don't know how to bring your dead device back to life please don't make any modifications and stay with stock MIUI. This is only meant for advanced users.
Features :
-Compiled with UBER 6.4.1 TC-
-CPU/GPU O.C[for all variants]-
-Savoca KCAL-
-Blu_active Cpu Gov-
-FIOPS I/O-
-Chacha20 CRNG-
-Adreno Idler-
-Sound Contol-
-Slimbus O.C for better sound quality-
-Vibration Control Intensity-
-ExFat/NTFS Support-
-Toggleable Software CRC-
-TCP congestion Algorithms-
-Misc Changes-
-Spectrum support-
Installation:
-Boot Into Recovery-
-Flash Kernel-
-Wipe Cache and Dalvik (Optional)-
-Reboot!-
Download :
https://www.mediafire.com/folder/5yu4ri9bumpts/Gemini
MiUi-Gemini is for MiUi 9 ( or MiUi 9 based roms )
HMP-Gemini is for LOS or other Los based roms.( w/o EAS support )
EAS-Gemini is for EAS supported roms.
EAS-voxpopuli-Gemini is for EAS supported roms which using Vox Populi Power HAL.
* users should use spectrum to load the kernel settings ( balance profile ) on every boot. *
--------------------------------------------------------------------------------------------------------------------------------------
Credits:
bgcngm-franciscofranco-Sultanxda-flar2-eng.stk-The Flash-frap129-osm0sis
--------------------------------------------------------------------------------------------------------------------------------------
Contributors:
MEGAX91
Source :
https://github.com/GUYVER91/Capricorn
don't dirty Flash my kernel on any other custom kernel , if you are coming from another custom kernel , first flash your Rom's stock kernel through Fastboot , then Flash my kernel.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
these are my kernel settings , you can use them in case you can't use spectrum.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
never post problems without full details of what setup you are using, it's not possible to help that way.
Provide me some logs:
- ADB logcat dump
- /sys/fs/pstore contents
- dmesg dump
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Only use EAS builds alongside EAS supported roms..
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
if you think your battery life is not good enough , use betterbatterystats and find the battery drain causes..
Changelog :
v3.0 :
[HMP Builds] :
-removed OC frequencies ( standard SD820 frequencies are still available for 32GB variant )
-updated Wlan Driver
-updated blu_active CPU Gov
-updated sound control
-updated thermal driver
-updated cpuidle driver
-updated F2FS driver
-memory management improvements
-upstream updates
-bug fixes
[EAS Builds] :
-removed OC frequencies ( standard SD820 frequencies are still available for 32GB variant )
-updated Wlan Driver
-updated sound control
-updated thermal driver
-updated cpuidle driver
-updated F2FS driver
-memory management improvements
-upstream updates
-bug fixes
v2.0 :
[HMP Builds] :
-Merge Last CAF branch LA.UM.5.5.r1-05800-8x96.0
-Updated Wlan Driver
-added hyperx CPU Gov
-added Tripndroid I/O Scheduler
-updated blu_active CPU Gov
-removed qpnp-fg family wakeup sources
-Blocked lot of kernel wakelocks
-updated EXT4 driver
-lot of upstream changes
-Bug Fixes
[EAS Builds] :
-Merge Last CAF branch LA.UM.5.5.r1-05800-8x96.0
-Updated Wlan Driver
-added Tripndroid I/O Scheduler
-added cpu-boost (optimized for EAS)
-removed qpnp-fg family wakeup sources
-Blocked lot of kernel wakelocks
-updated EXT4 driver
-lot of upstream changes
-Bug Fixes
v1.0 :
initial release
a bout EAS :
EAS stands for Energy Aware Scheduling , where the whole governor settings + HMP Settings are replaced by one system relying on "scheduler hints" from specifically modded low-level files including specially modded libs and framework patches.EAS aims to achieve better battery through lowering the product of V * I by altering the voltage along with the frequency dynamically based on loads calculation and the frequency used and many other variables.
EAS will set the core > Frequency > voltage per task. If the scheduler decided that a task needs a higher freq then it supplies that before the task is placed on a core.
Also the great thing about EAS (When tuned and setup properly) is that it is setup to not overshoot and overpower task workload.
Unlike our standard governor like interactive that does sampling and cpu-boost. These both can overshoot the performance needs pf the current workload thus leading to energy loss.
in short : EAS is all about setting the stune groups and the cpusets and using a sched -or schedutil- governor. There has to be an energy model for the SoC so that there is proper energy costs calculation made
*Energy models are the voltage/frequency*
Nice to see this kernel for mi5.
It Should work with Aosp (extended)? It uses schedutil governor by default.
And.does.it have oc.for 32gb version?
RootNightmareX said:
Nice to see this kernel for mi5.
It Should work with Aosp (extended)? It uses schedutil governor by default.
And.does.it have oc.for 32gb version?
Click to expand...
Click to collapse
Reeead the OP! ^^
Second item under features: "CPU/GPU OC [for all variants]"
RootNightmareX said:
Nice to see this kernel for mi5.
It Should work with Aosp (extended)? It uses schedutil governor by default.
And.does.it have oc.for 32gb version?
Click to expand...
Click to collapse
yes , it works on AEX. ( on EAS build , schedutil is the default Gov )
OC is available for all variants.
Phil_Smith said:
Reeead the OP! ^^
Second item under features: "CPU/GPU OC [for all variants]"
Click to expand...
Click to collapse
Preeety sure it wanst there when i red it 1st time
RootNightmareX said:
Preeety sure it wanst there when i red it 1st time
Click to expand...
Click to collapse
Okay, I see. Sorry then.
Waow new kernel again. Great work, thank you..
Min 1,2ghz
Max 1,1ghz freq.
Its normal? Any recommaned freq?
Nice to see your kernel on Gemini! I used to follow it on Kenzo, will try it soon
RootNightmareX said:
Min 1,2ghz
Max 1,1ghz freq.
Its normal? Any recommaned freq?
Click to expand...
Click to collapse
No! min freq is 307200MHz! use spectrum and choose balance profile.
MEGAX91 said:
No! min freq is 307200MHz! use spectrum and choose balance profile.
Click to expand...
Click to collapse
The hmp version also got EAS? Sorry if it's a low question.
Eas works good with Pure Fusion, spectrum balanced mode so far so good.
masterlo3 said:
The hmp version also got EAS? Sorry if it's a low question.
Click to expand...
Click to collapse
No.
MEGAX91 said:
No.
Click to expand...
Click to collapse
Lol thanks. I figured. Downloaded and testing on JDCT AOSP
Thanks for miui kernel. I've used your kernel before on kenzo and it works fine. I hope it works fine too on gemini. Can you add flar2 wake gesture support on miui and los? Please keep update miui kernel. Thank you
can it work on rr roms？
Sheldon Lv said:
can it work on rr roms？
Click to expand...
Click to collapse
Sure it will
[KERNEL][OC/UC/UV] ꓘⓄ - 4.7.1 [DragonTC 8.0 + Linaro 7.3][.147 + 6.2.r1-10500][EOL]
ꓘⓄ KernelEOL NO MORE UPDATES (exams) FLASH ANY OTHER KERNEL
Telegram DISCUSSION & TESTING GROUP
General Improvements:
Built with DragonTC 8.0 and Linaro 7.3 gcc
Always up to date with Linux stable and latest CAF tag
CPU & GPU Improvements:
Overclocked Big cluster to 2.3Ghz and Little to 1.9Ghz
Underclocked Big and little to 300mhz
Undervolted and voltages adjusted
Several CPU Governors available - Chill, Alucard, Nightmare, Ironactive, Cultivation, Impulse, ZZMoove big.LITTLE Edition, Blu active, Tripndroid, Cafactive
Adreno Idler and Adrenoboost available
Network improvements:
Implemented Wireguard VPN support usable with Azire VPN
Enhanced TCP methods - cubic, westwood, vegas, scalable, CHINA, Agile-SD, many more
I/O improvements:
Several I/O control tweaks
Added schedulers - Maple, Zen, Vr, Tripndroid, Sioplus, SIO, FIOPS, Fifo
Adaptive LMK
Added UKSM
Dynamic FileSync toggle
Disabled I/O CRC check for more performance
Screen Improvements:
sRGB and KCAL - Advanced color control for Qualcomm MDSS v2 (RGB calibration and post-processing features)
Backlight dimmer for lower minimum brightness
Battery improvements:
USB Fast Charge
Boeffla Wakelock blocker available
Miscellaneous improvements:
Vibrator Strength tunable
Added Nav Bar gesture
Much more, refer git
DOWNLOADS
XDA:DevDB Information
ꓘⓄ Kernel, Kernel for the Asus ZenFone Max Pro M1
Contributors
Sudeep Duhoon
Source Code: https://github.com/SudeepDuhoon/KO.git
Kernel Special Features: Always up to date with linux stable and caf sources, feature rich and stable
Version Information
Status: Stable
Created 2018-07-18
Last Updated 2018-08-16
ChangeLogs :-
v4.7
nu time to update changelogs sry
flash and feel the difference
v4.0
Check github
v2.5
Merged .141 & .142
Merged LA.UM.6.2.r2-04700
Permissive denials logging disabled
Enable core control
Adrenoboost:conservative governor
Allow 320K AAC encoding
Powersuspend PM kernel driver
Gentle fair sleepers disabled by default
State notifier updates and switch removed
TCP congestion algorithm: CHINA & Agile-SD
Governor: Cafactive
Slow charging fix? (test)
Lot more under the hood changes and improvements
v2-
1. Merged .141
2. CPU governors added:-
Chill
Interactive (additions)
Add Support to Display State
Add powersave bias tunable
Add screen off max frequency tunable
3. Fixed min frequency of Little cluster stuck at 1536
4. CRC Check toggle
5. Added KSM, UKSM
6. Added Nav Bar gesture
7. Added Simple GPU Algorithm.
8. Added CAKE packet scheduler
9. Disabled adreno idler by default
10. LZ4 compressor updates
11. O3 Optimizations
12. Turned off Core Control Hotplug and Performance Hotplug (testing)
13. Updated anykernel2
v1-
1. Merged .140
2. Latest CAF Tag
3. CPU governors:-
alucard, nightmare, ironactive, cultivation, impulse, ZZMoove big.LITTLE Edition, blu active, tripndroid.
4. I/O Scheduler:-
Maple, zen, vr, tripndroid, sioplus, SIO, FIOPS, fifo.
5. TCP congestion algorithms:-
cubic, westwood, vegas, scalable.
6. CRC Check disabled (toggle from next build)
7. State Notifier (enabled by default)
8. WakeLock Toggles
9. KCAL Control
10. Arch Power
11. Arch Capacity
12. Gentle Fair Sleepers
13. Powersuspend
14. Enable FP Boost (testing needed)
15. Adreno Idler
16. Adreno Boost
17. CPU Wake Boost
18. Wireguard Support
19. Boeffla WakeLock Blocker
20. Fsync on/off support
21. USB fast charge
22. MSM Preserve Memory
23. File System Improvements
24. Better Decompression Performance
this kernel works only custom or both stock and customrom ?
savijaysalem said:
this kernel works only custom or both stock and customrom ?
Click to expand...
Click to collapse
both
Sudeep Duhoon said:
both
Click to expand...
Click to collapse
does/would usb otg work after flashing this? see my post here. thanks for any help.
This kernel has increased my mobile's memory management score on DOT OS
Steps to flash !!
anandushari said:
Steps to flash !!
Click to expand...
Click to collapse
Download kernel zip ,flash in recovery , wipe cache/dalvik(not compulsory) , reboot
james11705 said:
Download kernel zip ,flash in recovery , wipe cache/dalvik(not compulsory) , reboot
Click to expand...
Click to collapse
do root is required or not
anandushari said:
do root is required or not
Click to expand...
Click to collapse
No , but u need to unlock ur bootloader and flash a custom recovery like twrp or red Wolf , before flashing this zip.
I do not understand half of the things listed in the improvements. However, something caught my attention: USB Fast Charge. Does this means the phone will support fast charging once this kernel is flashed?
After installing. My phone is asking to format sd card and shows currpted. Rebooted and clear dalvik cache same error back to stock kernel. Using stock rom 316
Update 2.5
Merged .141 & .142
Merged LA.UM.6.2.r2-04700
Permissive denials logging disabled
Enable core control
Adrenoboost:conservative governor
Allow 320K AAC encoding
Powersuspend PM kernel driver
Gentle fair sleepers disabled by default
State notifier updates and switch removed
TCP congestion algorithm: CHINA & Agile-SD
Governor: Cafactive
Slow charging fix? (test)
Lot more under the hood changes and improvements
Aftab_khatri said:
After installing. My phone is asking to format sd card and shows currpted. Rebooted and clear dalvik cache same error back to stock kernel. Using stock rom 316
Click to expand...
Click to collapse
send boot time log
don't wipe anything, just reboot
are you using xposed module?
abubin said:
I do not understand half of the things listed in the improvements. However, something caught my attention: USB Fast Charge. Does this means the phone will support fast charging once this kernel is flashed?
Click to expand...
Click to collapse
through USB 3 port, yes
Dumb question.
How should I use boeffla wake lock blocker
Dt2w support?
Sent from my G5 SE using XDA Labs
Sudeep Duhoon said:
send boot time log
don't wipe anything, just reboot
are you using xposed module?
Click to expand...
Click to collapse
How to take log ? And no i don't use xpose its battery hog and makes.device laggy
Is it possible that we get WiFi 5ghz band as the SoC supports it? And also what about Qualcomm quick charge?
How fast does it charge? 3000mA at 4V? Or even more?
=BUTTERFLY KERNEL=
Your warranty is now void!
We're not responsible for bricked devices, dead SD cards,
thermonuclear war, or you getting fired because the alarm app failed. Please
do some research if you have any concerns about features included in this ROM
before flashing it! YOU are choosing to make these modifications, and if
you point the finger at us for messing up your device, we will laugh at you
Features:
Pie base: CAF & Prima Tag by LA.UM.7.6.r1-04500-89xx.0
Oreo base: CAF & Prima Tag by LA.UM.6.6.r1-11000-89xx.0
Legacy base: not updated pure sources from MiCode github
(prima tag LA.UM.7.6.r1-05500-89xx / LA.UM.6.6.r1-11300-89xx.0)
• KCAL color control
• Vibration intensity control
• Sound gain control
• Audio codec quality improved
• exFAT Support
• NTFS support
• F2FS support
• SquahFS support
• CIFS/SMB support
• Added CPU Hotplug (default disabled)
• Set lz4 for better zram work
• Boeffla wakelock blocker
• Added defaults rules for Boeffla wakelock blocker
• Disable vendor verify and set no verity
• CRC32: disable by default & enable toogle (average 30% I/O performance profit)
• Few patches from Franco kernel (disabled a lot of debugging stuff)
• Fsync: on/off support
• Battery deep optimisation: undervolting & additional tweaks
• Added Adreno Real Idler (supported turning it on/off)
• Improved interactive governor (patch from Franco kernel)
• Improved CPU boost, default is disabled (patch from Franco kernel)
• Improved conservative governor (patch from Franco kernel)
• I/O schedulers: noop, deadline, bfq, cfq (default), sio, fiops, maple, tripndroid, zen, anxiety, sioplus, fifo, v(r)
• Added CPU governors: darkness, zzmoove, relax, impulse, electron, nonconservative, lionheart, clarity, blu_active, yankactive, intelliactive, conservativex, ondemandx, interactivex, bioshock, darknessv5, alucard, smartmax_eps, pegasusq, lionfish, hyper, despair, barry_allen, xperience, alessa, chill, ondemandplus, ironactive, culvitation, tripndroid
• Added GPU governors: guardian, balanced, msm-adreno-plus
• TCP congestion algorithms: cubic, reno, westwood (default)
• Installer include fix for Wi-Fi SELinux permission
• Kernel installer also support custom ROMs
• GCam focus fix (thanks @teftel1608 and @33bca)
• GPU: clocks table reworked (lags free, performance grew). OC max gpu freq now is 725MHz
• Added WireGuard 0.0.20190601
• Fix for goodix-fp gestures on stock (thanks to @artyom5613 & @Broomber)
• Also in the v4 installer included fix fpc-fp gestures for the customs rom
now gestures for both fingerprints is are:
* swipe2right - paste text
* others like in rom's setting
(if you not like this - change it in the /system/usr/keylayout/uinput-*.kl)
• Memory & battery life optimization due config settings for kernel
• Added a block to wakelock from wifi
• I/O optimization
• Hide unlocked bootloader state (for apps like bank clients etc)
• Patches from Franco "mido" kernel for battery life improvement
• Added gpu Adreno simple algorithm (beast!!)
• Found a reason for which the CPU could for a long time not to raise the frequency to the maximum, it's all in the file /vendor/etc/thermal-engine.conf
See samples how to improve situation
• Compiled with GCC 9.1.0, which gave an increase in performance and speed of the kernel
• Reworked undervolting, battery lives even longer
• Added voltage control
• Maximum CPU frequency is now 2.4GHz
• EUOC version has a maximum GPU frequency of 750MHz
• added support for display status for CPU Hotplug & some schedulers
• all schedulers that have display status support:
alucard, chill, clarity, cultivation, darkness, electron, impulse, intelliactive, ironactive, nightmare, relaxed, anxiety-iosched and maple-iosched
• added drivers for few USB-Ethernet adapters
• added nightmare and dancedance CPU governors
• updated version with 2.2GHz overclocking
• removed the patch for hiding the bootloader state (there are more problems than good with it)
• new settings for a smooth interface in installer (applied for GSI only)
- DT2W fix for fts_ts [default disabled] (thanks @33bca) * tested on customs and GSIs. for latest maybe need to enable "Handwave gesture" in "Phh Treble Settings" > "Doze features" * #TODO
- Installer include Magisk preserve #TODO
<< download Pie v5.5 || download Pie v4.4 >>
<< download Oreo v5.5 || download Oreo v4.4 >>
undervolted (U) lower voltage for decrease overheat. also incredible battery saving
overclocked (OC) CPU max frequency is 2.4GHz, GPU max frequency is 725MHz
extra-overclocked (E) GPU max frequency is 750MHz (if you will face with graphical glitches - don't use it!)
Installations:
Backup boot.img, /system/lib/modules, /system/usr/keylayout and /vendor/lib/modules folders, /vendor/bin/init.qcom.post_boot.sh file if you want to go back
Flash Zip file with any TWRP recovery, wipe Dalvik cache, reboot and enjoy ^_^
Notice: if you have Magisk with modules installed maybe you'll get bootloop.
If you have Magisk don't need reinstall it after kernel because installer will save Magisk #TODO
Right way: if you have Magisk and modules - deinstall all. Then flash stock boot.img, then custom kernel, then other stuff like TWRP and Magisk.
Enough just dirty flashing kernel and then Magisk if you need it. All yours Magisk modules will preserved.
Issues:
- DT2W not work for fts_ts touchscreen
- tell me if find
XDA:DevDB Information
Butterfly kernel for Xiaomi Mi A2 Lite "daisy"
Contributors:
eremitein
Source Code:
https://github.com/eremitein/xiaomi_kernel_msm8953_daisy_butterfly
CREDITS:
All people, who made good code for this platform
Version Information
Status: Stable/Experimental
Release Date: 2019-04-15 (UTC +0)
Created: 2019-04-07
Last Updated: 2019-08-08
.
=VARIOUS POWER PROFILES=
[BATTERY DEEP BACKUP]
CPU governor: conservative
CPU max freq: 1804 MHz
GPU governor: msm-adreno-tz or guardian
Adreno idler: on
Tune Boeffla Wakelock Blocker: read this manual
CPU Hotplug: see attached screenshot
# Give ~10 minutes SOT per 1% battery while web browsing #
[NORMAL MODE]
CPU governor: ondemand / interactive
CPU max freq: set highest
GPU governor: msm-adreno-tz or balanced if lagzzs)
Adreno idler: on
CPU Hotplug: off
# Give ~8 minutes SOT per 1% battery while web browsing #
[PERFORMANCE MODE]
CPU governor: intelliactive, blue_active or nonconservative
CPU max freq: set highest
GPU governor: performance or msm-adreno-plus
Adreno idler: on
CPU boost: on
CPU boost freq: set to 1.84, 2.0 or 2.2GHz
CPU Hotplug: off
# Give ~5 minutes SOT per 1% battery while web browsing #
.
I will not help users if they are:
- using Magisk and moreover they installed modules;
- made any kernel settings (selected exotic governors, turned on hotplug and etc.);
- using option "Disable HW overlays";
- not sure that the same problems were not on the standard kernel
- not follow installation guide
All OC versions is always have CPU 2.2GHz
if not for you, then this is maybe if:
- you SoC/voltageregulator/phone doesn't support overclocking
- your device overheated due high outside temp or high load
- you system set restrictions to overclocking
.
Now im using CAF kernel with stock rom i want to flash butterfly what should i do delete CAF then install it??and for magisk delete all modul ?
hendri88 said:
Now im using CAF kernel with stock rom i want to flash butterfly what should i do delete CAF then install it??and for magisk delete all modul ?
Click to expand...
Click to collapse
yes, thats right
you may try dirty install but this is not a guarantee what system boot due to magisk specific
best way is remove all modules from magisk, remove magisk via flashing stock kernel and then boot to twrp and install butterfly
eremitein said:
yes, thats right
you may try dirty install but this is not a guarantee what system boot due to magisk specific
best way is remove all modules from magisk, remove magisk via flashing stock kernel and then boot to twrp and install butterfly
Click to expand...
Click to collapse
Ok i will try it thx bro
added power modes samples
https://forum.xda-developers.com/showpost.php?p=79288538&postcount=2
May I ask if this kernel could be modified so we can overclock? How exactly do we need to go about and do the modifications to the PLL tables? It'd be great if you could help out and make a tutorial or something.
Zewyni said:
May I ask if this kernel could be modified so we can overclock? How exactly do we need to go about and do the modifications to the PLL tables? It'd be great if you could help out and make a tutorial or something.
Click to expand...
Click to collapse
no, this build haven't overclock feature
Kernel updated (download v2)
Changelog v2:
Pie CAF & Prima updated to LA.UM.7.6.r1-04500-89xx.0
Improved interactive CPU governor (patch from Franco kernel)
Improved CPU boost and enable it (patch from Franco kernel)
Reworked conservative and nonconservative CPU governors
Reworked guardian, balanced and msm-adreno-plus GPU governors
Kernel installer now also support custom ROMs
Also have some changes in Power profiles
The touch sensetivity is somehow better with this kernel but I really miss dt2w... I'll be testing it for the week, hope you can fix dt2w! Thanks for your work on our device!
Eddie_53 said:
The touch sensetivity is somehow better with this kernel but I really miss dt2w... I'll be testing it for the week, hope you can fix dt2w! Thanks for your work on our device!
Click to expand...
Click to collapse
dt2w not supporting due missing stuff in official Xiaomi kernel sources
https://github.com/MiCode/Xiaomi_Kernel_OpenSource/issues/1044
I can confirm that touch sensitivity is better on this Kernel. Gcam also runs smoother!
ExFAT support doesn't seem to be working though. I've tried to read an SD Card ExFAT formatted and it didn't work (corrupt error message).
eremitein said:
=VARIOUS POWER PROFILES=
[BATTERY DEEP BACKUP]
CPU governor: conservative
CPU max freq: 1689 MHz
GPU governor: guardian or msm-adreno-tz
Adreno idler: on
Tune Boeffla Wakelock Blocker:read this manual
CPU Hotplug: see attached screenshot
# Give 10-12 minutes SOT per 1% battery while web browsing #
[NORMAL MODE]
CPU governor: ondemand / interactive
CPU max freq: 2016 MHz
GPU governor: msm-adreno-tz or balanced if lagzzs)
Adreno idler: on
CPU Hotplug: off
# Give ~6 minutes SOT per 1% battery while web browsing #
[PERFORMANCE MODE]
CPU governor: nonconservative
CPU max freq: 2016 MHz
GPU governor: performance or msm-adreno-plus
Adreno idler: off
CPU Hotplug: off
# Give 4-5 minutes SOT per 1% battery while web browsing #
.
Click to expand...
Click to collapse
How to switch from one profile to another? I have kernel adiutor installed but there is no profile I the kernel section to select. Thanks to everyone answer and to the Dev for his work. Sorry for my English
Kr47os said:
How to switch from one profile to another? I have kernel adiutor installed but there is no profile I the kernel section to select. Thanks to everyone answer and to the Dev for his work. Sorry for my English
Click to expand...
Click to collapse
you may create various profiles in Kernel Aduitor
Tools > Profile
and which rom you using?
eremitein said:
you may create various profiles in Kernel Aduitor
Tools > Profile
and which rom you using?
Click to expand...
Click to collapse
I'm using stock ROM Pie 10.0.4 update version.
Kernel updates (see topic)
Changelog v2.99:
Added new builds:
- Oreo base CAF & Prima Tag by LA.UM.6.6.r1-11000-89xx.0
- Legacy base (not updated pure sources from MiCode github)
- Installer totally fixed for support wifi on custom roms
Oreo base is only for oreo vendors (9.6.x.0 versions)!!!
Why i built this and legacy variants?)
For compatibility. Because some people still using oreo stock or 8.1 vendor with GSI
BJumperBR said:
I can confirm that touch sensitivity is better on this Kernel. Gcam also runs smoother!
ExFAT support doesn't seem to be working though. I've tried to read an SD Card ExFAT formatted and it didn't work (corrupt error message).
Click to expand...
Click to collapse
for clean testing exFAT you need should be sure what ROM have support this FS
if with other kernel on your rom exfat work then, yeahh, something wrong with my kernel exfat
thanks for feedback)
eremitein said:
for clean testing exFAT you need should be sure what ROM have support this FS
if with other kernel on your rom exfat work then, yeahh, something wrong with my kernel exfat
thanks for feedback)
Click to expand...
Click to collapse
I'm on Stock ROM 10.0.4.0.
So, no exDAT support, right?
I am undecided whether to stay in oreo with this kernel or pie always switch to this kernel.
It is wrong to ask, instead of trying, but I don't have much time to test
No one with any feedback on the battery and stability?
(Noob question, what is it the difference of legacy kernel? )