Need help here,
So, i flashed .eu 9 on Mi6, all went normally, all good, i put it in the charger at night.
In the morning of today, i woke up with my phone DEAD connected in the charger (the original with original cable)
When i connect in any charger, the notification LED blinks, BUT MY PHONE DOESN'T TURN ON, IT DOESN'T BOOT! No matter what button i press
When it's not on the charger, he does nothing.
Can someone tell WTF happened and how to solve this?
I'm exactly at the same situation.
Hardbricked after Miui9 update.
Device is detected as Qualcomm HS-USB QDLoader 9008 on PC, but Miflash fails with errors:
- cannot receive hello packet
- try to reset status
Any help is appreciated!
Thanks in advance :good:
BPSoft said:
I'm exactly at the same situation.
Hardbricked after Miui9 update.
Device is detected as Qualcomm HS-USB QDLoader 9008 on PC, but Miflash fails with errors:
- cannot receive hello packet
- try to reset status
Any help is appreciated!
Thanks in advance :good:
Click to expand...
Click to collapse
Hi
try to download one of the tools from this link http://forum.gsmdevelopers.com/showthread.php?t=24421
if you keep having this error just use another version.
hac12 said:
Hi
try to download one of the tools from this link http://forum.gsmdevelopers.com/showthread.php?t=24421
if you keep having this error just use another version.
Click to expand...
Click to collapse
Thank you!
I resolved my issue disabling driver signature enforcement and reinstalling qualcomm drivers that come with Miflash.
For further instructions please follow this link:
https://www.howtogeek.com/167723/ho...so-that-you-can-install-unsigned-drivers/amp/
In my case was important to do it even if windows device manager recognize my device correctly, and miflash detected my mobile.
Clean flash via mi flash tool
MI 6 cihazımdan Tapatalk kullanılarak gönderildi
Mods please close this thread
My MI6 is officially hard bricked and there's no repair.
I'm sending it back to china
BPSoft said:
Thank you!
I resolved my issue disabling driver signature enforcement and reinstalling qualcomm drivers that come with Miflash.
For further instructions please follow this link:
https://www.howtogeek.com/167723/ho...so-that-you-can-install-unsigned-drivers/amp/
In my case was important to do it even if windows device manager recognize my device correctly, and miflash detected my mobile.
Click to expand...
Click to collapse
BPSOFT which rom you used my mi6 is in Dead brick mode and would like to recover it
XeeXa said:
BPSOFT which rom you used my mi6 is in Dead brick mode and would like to recover it
Click to expand...
Click to collapse
To use Mi Flash Tool you need to download Fastboot ROM. The Fastboot ROM extension's file are .tar, .gz*or.tgz.
But if you bootloader is still locked you need to boot in EDL mode, not fastboot mode.
More info at:
https://xiaomifirmware.com/guides-and-tips/guide-flash-miui-rom-xiaomi-mi6/
Related
When I boot my device no shows LG logo and does not come into download / recovery mode :crying:
any idea to fix it?
AnDyZ-BR said:
When I boot my device no shows LG logo and does not come into download / recovery mode :crying:
any idea to fix it?
Click to expand...
Click to collapse
What does it say when you plug it into the computer?
QHUSB_BULK?
I guess the better option is to try using LG flash tool to flash kdz, not sure if download mode will be booted since you mentioned download mode failed.
If none really work then should consider restoring stock rom using LG pc suite
Am I correct in saying the phone simply does not boot into download mode? You have have the phone off, hold + or - and plug USB in?
itsbighead said:
What does it say when you plug it into the computer?
QHUSB_BULK?
Click to expand...
Click to collapse
yes, say QHUSB_BULK
XPS_93 said:
I guess the better option is to try using LG flash tool to flash kdz, not sure if download mode will be booted since you mentioned download mode failed.
If none really work then should consider restoring stock rom using LG pc suite
Click to expand...
Click to collapse
does not work LG flash tool / LG PC suite" without the download mode!
drolgnir said:
Am I correct in saying the phone simply does not boot into download mode? You have have the phone off, hold + or - and plug USB in?
Click to expand...
Click to collapse
yes and yes =/
May I ask how did you brick it?
hey guys, I repaired using this method ....
http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091
and
http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853
i flash my rom using TWRP recovery
thank you xda users
asking for help
Hello!
I would like to ask you, that can you maybe help me with my LG G3 (D855) (16GB). I live in Europa, Hungary
I bought the device as used, and i would have liked to download the latest software via wifi, then on the phone restarted, and was only the TWRP on the phone, i restarted the device again, but i could entry only in the TWRP. I downloaded a ROM from the XDA, and i made a mistake, i installed the D851 software. The phone is bricked, no download mode. I tryed to unbrick, but every method need the download mode. If i put the device on the PC, the PC see only as modem. LGE AnroidNet USB modem, and the the port name LGE AnroidNet USB Serial Port Com4. If the battery is low, i see on the display, that show that need to charge, but nothing more life signal. If you can help me with some information and with files or via teamviewer, i will glad for you, and also donate. i think i have the correct TOT file, and the DLL file.
LGD855AT-00-V10k-234-30-VUK-SEP-03-2014-16G+0.tot
LGD855_20140526_LGFLASHv160.dll
I downloaded a program "BoardDiag3.99c.zip". but this program ask the BIN file, i found another program b2b.exe, that ask the TOT file at the extraction. Maybe that's is same?
As i wrote the PC sees my phone only as modem, and LGE AnroidNet USB Serial Port Com4. I dont know what is "Qualcomm HS-USB QDLoader 9008 mode", i dont see in the port menu. I hope that You, or someone can help me. i downloaded the QDLoader HS-USB Driver, but again show only the "LGE AnroidNet USB Serial Port Com4" (or now this is com41, i wanted to try a method, but need the download mode) Sorry for the bad english.
Have a nice day!
i have the same issue
AnDyZ-BR said:
hey guys, I repaired using this method ....
http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091
and
http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853
i flash my rom using TWRP recovery
thank you xda users
Click to expand...
Click to collapse
Please give a step by step tutorial since l cant seem to figure out how you solved the issue
Hello,
I tried to flash my phone from global 8.0.3.0 stable to 8.2.4.0MAGCNDL China Stable. Miflash said flashing was successfull, but then I started my phone and was on a bootloop.
I cannot access edl mode via deep flash cable anymore, it´s just loading. My phone isn´t unlocked that´s why i can´t flash over fastboot. I already tried to the recover mode and downloaded a chinese version of Mi Pc Suite. It detects my device but when I try to recover it switches for like 3 secs to the right screen but then immediately switchs back to the first screen (connect device).
One thing i´ve noticed is there is an option to choose a xiaomi ota file, what is that, because I can´t find anything.
Is there any hope for my phone?
Not good, you shouldent even try to flash china stable(you can but why). so, i think you should enter EDL with testpoints, or you can try do hard reset, maybe this will work.
use this method and then flash your mi5s with stable global.
http://en.miui.com/thread-310325-1-1.html
Download Mi PC suite china version then enter recovery mode and connect the phone to pc,let it make the update and your done.
mezutelni said:
Not good, you shouldent even try to flash china stable(you can but why). so, i think you should enter EDL with testpoints, or you can try do hard reset, maybe this will work.
Click to expand...
Click to collapse
Thanks for your reply, how can I hard reset my device? And I watched a yt video for tespoints , is it the same procedure as with the mi5 ?
hzare2611 said:
use this method and then flash your mi5s with stable global.
Click to expand...
Click to collapse
I got a Edl cable, but I can´t get into edl.
XMoDuLeSx said:
Download Mi PC suite china version then enter recovery mode and connect the phone to pc,let it make the update and your done.
Click to expand...
Click to collapse
Not working, it just stops immediatly the process, if I press recover
Then u need to connect the phone via USB 2 not 3 and install the correct driver's. The phone must be detected Android adb interface
XMoDuLeSx said:
Then u need to connect the phone via USB 2 not 3 and install the correct driver's. The phone must be detected Android adb interface
Click to expand...
Click to collapse
I´ve installed all drivers and it´s connected to a usb 2 port. Phone is in Device Manager under "Kedacom USB Device/Android ADB Interface"
if you cannat connect the phone as edl,you should give it to mobile repaire center and they fix it with boot boxes for you.
Thanks for all your help guys, I finally recovered my phone and I´m on Lineage OS now.
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
*additional informations*
here are the steps i followed:
1) unlocked bootloader succesfully
2) flashed official twrp
3) wiped EVERYTHING except sd ext
4) flashed this firmware
https://sourceforge.net/projects/xiaomi-firmware-updater/files/Developer/
5) flashed this rom
https://forum.xda-developers.com/re...ment/ota-resurrection-remix-os-6-0-0-t3777375
6) rebooted, dead
I noticed now that if i try to turn on the phone, the led blinks a few times
PROBLEM SOLVED:
the phone is alive again. Here is what I have done-
1) I opened the phone and tried the test point method, but I noticed that nothing changed in the way the phone was detected by my laptop. So, it's not crucial have "COM 7" in device manager.
Then I basically followed the steps suggested by @Destrangis in post #3
2- In MiFlash Choose CLEAN ALL and install this rom: http://bigota.d.miui.com/V9.2.7.0.NE...179eb04f38.tgz
3- Installed TWRP, WIPES and flash https://androidfilehost.com/?fid=5862345805528041092 and Magisk
4- Come back TWRP, WIPES and install your favorite rom.
Click to expand...
Click to collapse
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
EDL booting and flashing is your solution.
Now, only debatable is will you use EDL booting procedure which requires opening of the phone to short two contacts to be able to boot in EDL or You will use altered ADB which gives possibility to boot in EDL without case opening. This second option is somehow questionable but first, i think, if second option to enter EDL without opening is way to go!
---------- Post added at 07:37 PM ---------- Previous post was at 07:03 PM ----------
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
I hope this guide will help you!
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
Hard brick. I went through it. Follow these steps: https://www.youtube.com/watch?v=lfkRHAW2iXI .
1- You have to activate the EDL mode.
2- In MiFlash Choose CLEAN ALL and install this rom: http://bigota.d.miui.com/V9.2.7.0.N...EK_20180406.0000.00_7.1_global_179eb04f38.tgz
3- Installed TWRP, WIPES and flash https://androidfilehost.com/?fid=5862345805528041092 and Magisk
4- Come back TWRP, WIPES and install your favorite rom. :good:
PD: If you see "COM7" in MIFLASH, go directly to step 2.
---------- Post added at 07:59 PM ---------- Previous post was at 07:55 PM ----------
Jehonan said:
EDL booting and flashing is your solution.
Now, only debatable is will you use EDL booting procedure which requires opening of the phone to short two contacts to be able to boot in EDL or You will use altered ADB which gives possibility to boot in EDL without case opening. This second option is somehow questionable but first, i think, if second option to enter EDL without opening is way to go!
---------- Post added at 07:37 PM ---------- Previous post was at 07:03 PM ----------
I hope this guide will help you!
Click to expand...
Click to collapse
The second opcion (ADB) doesnt work in RMN5.
what rom caused the brick?
devcon69 said:
what rom caused the brick?
Click to expand...
Click to collapse
info updated in the first post.
Is it crucial to have COM 7 port for EDL?
so, its been over a day now, have you fixed the problem?
t.hasan1 said:
so, its been over a day now, have you fixed the problem?
Click to expand...
Click to collapse
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
lomax84 said:
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
Click to expand...
Click to collapse
Whats did you do?
lomax84 said:
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
Click to expand...
Click to collapse
what method you solved your brick phone ?
Give the method you do
Error: Cannot read hello packet. Why solved?
following...how did you solve it ? come on
mxilil said:
what method you solved your brick phone ?
Click to expand...
Click to collapse
masjiko said:
Give the method you do
Click to expand...
Click to collapse
please see first post
I tried to test point to give flash in the rom by Miflash, the pc recognizes my device in the COM port, when initiating the process it gives an error message: CAN NOT READ HELLO PACKET. Does anyone know how I can solve this problem? my device is simply dead because of that anti-rollback that Xiaomi implemented.
Diegosdias said:
I tried to test point to give flash in the rom by Miflash, the pc recognizes my device in the COM port, when initiating the process it gives an error message: CAN NOT READ HELLO PACKET. Does anyone know how I can solve this problem? my device is simply dead because of that anti-rollback that Xiaomi implemented.
Click to expand...
Click to collapse
Did you removed the battery?
devcon69 said:
Did you removed the battery?
Click to expand...
Click to collapse
yes...
Diegosdias said:
yes...
Click to expand...
Click to collapse
Try to use usb 2.0 ports.
Maybe edl mode has timed out. Press the power button for 20-30 seconds to power cycle the phone.
Or open it up and remove battery pin for a minute. Reconnect and try again.
devcon69 said:
Try to use usb 2.0 ports.
Maybe edl mode has timed out. Press the power button for 20-30 seconds to power cycle the phone.
Or open it up and remove battery pin for a minute. Reconnect and try again.
Click to expand...
Click to collapse
I already tried on usb ports 2 and 3, and it did not work. Holding the buttons for a long time did not solve either. I opened it to test point, removed the battery, but none of it makes the phone work. The problem is that at the time of fash in Miflash it gives the following error: CAN NOT READ HELLO POCKET. I do not know what this error is or what it is about?
lomax84 said:
please see first post
Click to expand...
Click to collapse
Did you recognize what caused the hard brick to your phone?
I think you followed the right steps, yet your phone got hard bricked, is it a firmware issue or RR rom issue?!
Ahmed_HM said:
Did you recognize what caused the hard brick to your phone?
I think you followed the right steps, yet your phone got hard bricked, is it a firmware issue or RR rom issue?!
Click to expand...
Click to collapse
By following his link to the firmware file on sourceforge you will see that he flashed a note4x firmware on his note5... So guess where the issue was...
Hi, can someone help? I was about to flash the official whyred Linedage OS for my Redmi Note 5. I did that with note 3 and note 4 before, so kind of knew what I was doing.. But was not aware of the antirollback thing.. So after i decided to flash the new miui 10 firs for the firmware..(wasn't the best idea I know) and you know the rest.. something went wrong and now I am stuck with dead phone.. no recovery, no fastboot, nothing.. I had unlocked bootloader officially a few weeks ago, got the device connected with the mi account (not sure about if the account is authorized or not).
I tried the test point method - dissembling the device from miui dot com
I have the right driver listed in device manager (Qualcom HS-USB QDLoader 9008)
I tried several roms listed here or miui dot com
I tired several versions of MiFlash
Every time I only get the message about not reading the com port (tried all USB ports on two PCs, reinstalled drivers .. everything) .. It starts flashing "read hello packet", then after 5 seconds stops with the mesage "can not read from port comXY"
In edb its just waiting for the device on any command (or not devices found)
Anyone can help please? I spent the whole day searching for solution and found nothing, or nothing helps
thx in advance
I am in your same situation. did you solved it?
thank you
rfiore said:
I am in your same situation. did you solved it?
thank you
Click to expand...
Click to collapse
Yeah, posted my ID on the forum, got authorized, then used the "portable" miflash and it worked.. But on the other PC still got errors in miflash.. didn't even check for the authorization, so I suppose its PC related.. perhaps something with the drivers..
FKuzel said:
Hi, can someone help? I was about to flash the official whyred Linedage OS for my Redmi Note 5. I did that with note 3 and note 4 before, so kind of knew what I was doing.. But was not aware of the antirollback thing.. So after i decided to flash the new miui 10 firs for the firmware..(wasn't the best idea I know) and you know the rest.. something went wrong and now I am stuck with dead phone.. no recovery, no fastboot, nothing.. I had unlocked bootloader officially a few weeks ago, got the device connected with the mi account (not sure about if the account is authorized or not).
I tried the test point method - dissembling the device from miui dot com
I have the right driver listed in device manager (Qualcom HS-USB QDLoader 9008)
I tried several roms listed here or miui dot com
I tired several versions of MiFlash
Every time I only get the message about not reading the com port (tried all USB ports on two PCs, reinstalled drivers .. everything) .. It starts flashing "read hello packet", then after 5 seconds stops with the mesage "can not read from port comXY"
In edb its just waiting for the device on any command (or not devices found)
Anyone can help please? I spent the whole day searching for solution and found nothing, or nothing helps
thx in advance
Click to expand...
Click to collapse
I faced the similar situation. I pasted the ID in the russian and english forum. I got no message for weeks, I thought of flashing again, Voila. Device flashed and turned ON. Your device is hard bricked as mine, it needs authentication from Mi to flash via EDL mode. All you need to do is download the MI flash tool portable, and paste your Mi ID in forums.
Unfortunately both the forum's date to paste the ID has been expired. But still you try to get help from someone else from the forum or the moderators.
I'll explain different errors I faced and the solution for it.
"not reading the com port" --- You get this error when you flash Global version of the ROM. Use the Developer version of it.
"It starts flashing "read hello packet"" --- You get this error because edl is turned off in your phone. To turn it back ON, just remove the USB cable from your phone and then press the power button for 10-15 seconds. Then connect your phone back again and try to flash.
"edb its just waiting for the device on any command" --- Actually this is not an error. Your phone is hard bricked. While in hard bricked mode adb won't work. ADB works only in fastboot mode.
Simple.. Disconnect and Reconnect with your PC Via Testpoint.. Thanks.
thank you very much
Prabudeva005 said:
I faced the similar situation. I pasted the ID in the russian and english forum. I got no message for weeks, I thought of flashing again, Voila. Device flashed and turned ON. Your device is hard bricked as mine, it needs authentication from Mi to flash via EDL mode. All you need to do is download the MI flash tool portable, and paste your Mi ID in forums.
Unfortunately both the forum's date to paste the ID has been expired. But still you try to get help from someone else from the forum or the moderators.
I'll explain different errors I faced and the solution for it.
"not reading the com port" --- You get this error when you flash Global version of the ROM. Use the Developer version of it.
"It starts flashing "read hello packet"" --- You get this error because edl is turned off in your phone. To turn it back ON, just remove the USB cable from your phone and then press the power button for 10-15 seconds. Then connect your phone back again and try to flash.
"edb its just waiting for the device on any command" --- Actually this is not an error. Your phone is hard bricked. While in hard bricked mode adb won't work. ADB works only in fastboot mode.
Click to expand...
Click to collapse
I was lose hope because 12 hour my mido error cant read hello packet, and now fix it with your tips.. thanks a lot man
Prabudeva005 said:
I faced the similar situation. I pasted the ID in the russian and english forum. I got no message for weeks, I thought of flashing again, Voila. Device flashed and turned ON. Your device is hard bricked as mine, it needs authentication from Mi to flash via EDL mode. All you need to do is download the MI flash tool portable, and paste your Mi ID in forums.
Unfortunately both the forum's date to paste the ID has been expired. But still you try to get help from someone else from the forum or the moderators.
I'll explain different errors I faced and the solution for it.
"not reading the com port" --- You get this error when you flash Global version of the ROM. Use the Developer version of it.
"It starts flashing "read hello packet"" --- You get this error because edl is turned off in your phone. To turn it back ON, just remove the USB cable from your phone and then press the power button for 10-15 seconds. Then connect your phone back again and try to flash.
"edb its just waiting for the device on any command" --- Actually this is not an error. Your phone is hard bricked. While in hard bricked mode adb won't work. ADB works only in fastboot mode.
Click to expand...
Click to collapse
Thank you. I was in the "read hello packet" part and i was able to flash the Chinese rm
Thanks
Can u please give me your mi authorized I'd it will help for me
Am also stuck on edl mode redmi note 5 pro so please give me your mi I'd
Raviganthy said:
Am also stuck on edl mode redmi note 5 pro so please give me your mi I'd
Click to expand...
Click to collapse
https://forum.xda-developers.com/redmi-note-5-pro/how-to/fix-arb-bricked-device-qfil-t3841780
Help!
Help! i am also stuck on this problem on my Redmi 3. Can someone please help me?:crying:
---------- Post added at 06:18 AM ---------- Previous post was at 06:15 AM ----------
FKuzel said:
Yeah, posted my ID on the forum, got authorized, then used the "portable" miflash and it worked.. But on the other PC still got errors in miflash.. didn't even check for the authorization, so I suppose its PC related.. perhaps something with the drivers..
Click to expand...
Click to collapse
What forum?
can not read from port com xy
guilherme06 said:
Thank you. I was in the "read hello packet" part and i was able to flash the Chinese rm
Thanks
Click to expand...
Click to collapse
Hello, I've tried even developer rom, it displays the same error can not read from port com xy.
Even after doing test-point all over again.
By mistake I flashed wayne rom once, and phone boots but in a messed up fastboot mode.
talhosvi said:
Hello, I've tried even developer rom, it displays the same error can not read from port com xy.
Even after doing test-point all over again.
By mistake I flashed wayne rom once, and phone boots but in a messed up fastboot mode.
Click to expand...
Click to collapse
I have the same problem with my jasmine(which used to be wayne) when I tried to change it back into wayne again... do you have any solution already ?
kunoir said:
I have the same problem with my jasmine(which used to be wayne) when I tried to change it back into wayne again... do you have any solution already ?
Click to expand...
Click to collapse
have you find any solution?
jayspiker said:
have you find any solution?
Click to expand...
Click to collapse
i had the same problem but fixed with edl cable
Prabudeva005 said:
I faced the similar situation. I pasted the ID in the russian and english forum. I got no message for weeks, I thought of flashing again, Voila. Device flashed and turned ON. Your device is hard bricked as mine, it needs authentication from Mi to flash via EDL mode. All you need to do is download the MI flash tool portable, and paste your Mi ID in forums.
Unfortunately both the forum's date to paste the ID has been expired. But still you try to get help from someone else from the forum or the moderators.
I'll explain different errors I faced and the solution for it.
"not reading the com port" --- You get this error when you flash Global version of the ROM. Use the Developer version of it.
"It starts flashing "read hello packet"" --- You get this error because edl is turned off in your phone. To turn it back ON, just remove the USB cable from your phone and then press the power button for 10-15 seconds. Then connect your phone back again and try to flash.
"edb its just waiting for the device on any command" --- Actually this is not an error. Your phone is hard bricked. While in hard bricked mode adb won't work. ADB works only in fastboot mode.
Click to expand...
Click to collapse
where can i find this chinese rom for MI A3
talhosvi said:
can not read from port com xy
Hello, I've tried even developer rom, it displays the same error can not read from port com xy.
Even after doing test-point all over again.
By mistake I flashed wayne rom once, and phone boots but in a messed up fastboot mode.
Click to expand...
Click to collapse
same problem with me . Have you solved it ?? let me know please
Hi Guys,
I have the same problem trying to flash MIUI 11 in mi A3 with MIUI 12. Anyone knows a solution for this?
Hey thank you for reading this my mi note 8 is hardbricked are there any ways to fix it
i tryed to install a stable rom with twrp i cant go to fastboot and recovery mode
Please help me
If you can help me with fixing this i could pay if you want
Greetings Jerano
Jerano said:
Hey thank you for reading this my mi note 8 is hardbricked are there any ways to fix it
i tryed to install a stable rom with twrp i cant go to fastboot and recovery mode
Please help me
If you can help me with fixing this i could pay if you want
Greetings Jerano
Click to expand...
Click to collapse
Did you try to use MiFlash tool? If you don´t want to use test point then probably you could enter to EDL using hardware buttons, in other Xiaomi devices that I owned the combination key was keeping pressed both volume buttons at same time (it´s an accuracy timing move) that you connect with PC, open device manager in windows and see if device is detected under Qualcomm HS-USB QDLoader 9008, install first the proper drivers https://www.themefoxx.com/2018/07/qualcomm-hs-usb-qdloader-9008-driver.html
SubwayChamp said:
Did you try to use MiFlash tool? If you don´t want to use test point then probably you could enter to EDL using hardware buttons, in other Xiaomi devices that I owned the combination key was keeping pressed both volume buttons at same time (it´s an accuracy timing move) that you connect with PC, open device manager in windows and see if device is detected under Qualcomm HS-USB QDLoader 9008, install first the proper drivers https://www.themefoxx.com/2018/07/qualcomm-hs-usb-qdloader-9008-driver.html
Click to expand...
Click to collapse
Now this method won't work as flashing in EDL mode requires you to have an authorized account which xiaomi provides only to the service centers.
the_weird_aquarian said:
Now this method won't work as flashing in EDL mode requires you to have an authorized account which xiaomi provides only to the service centers.
Click to expand...
Click to collapse
Have the same problem with the account.
Will there be any way to install without the account?
Demon6672 said:
Have the same problem with the account.
Will there be any way to install without the account?
Click to expand...
Click to collapse
nah man, only way is to visit service center if you're stuck on EDL mode without recovery or fastboot.
the_weird_aquarian said:
Now this method won't work as flashing in EDL mode requires you to have an authorized account which xiaomi provides only to the service centers.
Click to expand...
Click to collapse
Oops, I completely forgot this, all my previous devices didn´t need it (Mi Max, R5+, Mi8L, MiA2L). Anyway double check before to try something weird with this device, in many countries (including mine) no service center available for. Thx for the info.
@Jerano : I don't know the status of your phone, but take a look here : http://4pda.ru/forum/index.php?showtopic=973206&st=420#entry91980022
(use online translators)
SubwayChamp said:
Oops, I completely forgot this, all my previous devices didn´t need it (Mi Max, R5+, Mi8L, MiA2L). Anyway double check before to try something weird with this device, in many countries (including mine) no service center available for. Thx for the info.
Click to expand...
Click to collapse
Yes I know...it worked on previous phones...but now xiaomi has started this new thing to give authorized accounts only to service center...
fratellos said:
@Jerano : I don't know the status of your phone, but take a look here : http://4pda.ru/forum/index.php?showtopic=973206&st=420#entry91980022
(use online translators)
Click to expand...
Click to collapse
That won't work either... it's a different thing..if your system is destroyed you'll get an error and your phone will still be able to boot to fastboot....if your phone doesn't boot to fastboot then you can't flash vbmeta.img
the system has been destroyed? on your screen?
Lanzer0 said:
the system has been destroyed? on your screen?
Click to expand...
Click to collapse
flash fastboot rom with miflash tools.
raptorddd said:
flash fastboot rom with miflash tools.
Click to expand...
Click to collapse
[ERROR] missing files script?sorry my English
Lanzer0 said:
[ERROR] missing files script?sorry my English
Click to expand...
Click to collapse
extracted the fastboot file twice?? also check if fastboot file path has no spaces in patch name.. but for system destroyed you can just flash vbmeta and recovery no need to flash full fastboot rom
Jerano said:
Hey thank you for reading this my mi note 8 is hardbricked are there any ways to fix it
i tryed to install a stable rom with twrp i cant go to fastboot and recovery mode
Please help me
If you can help me with fixing this i could pay if you want
Greetings Jerano
Click to expand...
Click to collapse
Any errors on screen or something?..or just black screen nothing else?
I cannot enter fastboot or recovery mode and the only way is EDL, but when installing ask for the authorized account, my question is if it can be installed by EDL without an account
Demon6672 said:
I cannot enter fastboot or recovery mode and the only way is EDL, but when installing ask for the authorized account, my question is if it can be installed by EDL without an account
Click to expand...
Click to collapse
Unfortunately..the answer is no... previously it was possible..but now xiaomi has changed it...it requires authorized account for edl flashing which xiaomi provides only to service centers