I have a cover for my tablet - can u recommend an app to auto turn on / off screen when I open / close the cover, because HOME button is quickly wearing out! Thanks.
I seem to remember that there were several complaints about their tablets shutting off when closing a third party cover. It turned out that there were magnets in the cover that affected the on/off switch. Maybe you could do a search to find out what cover they used and buy that cover. I may have seen that post somewhere on another forum also. Try a google search also as it may turn up the post you need.
armanys said:
I have a cover for my tablet - can u recommend an app to auto turn on / off screen when I open / close the cover, because HOME button is quickly wearing out! Thanks.
Click to expand...
Click to collapse
The tablet has built in functionality for this.
most folio cases have magnets in them that activate the screen when you open them.
That being said the magnet can temporarily interfere with the Waccom layer of the screen used to get Spen input. (the pen will stop reading accurately/at all in the areas affected by the magnet.)
there were a lot of reports of the magnets permanently affecting the screen but the official word is that if the magnet is removed from close proximity to the screen the issues will eventually go away. (This was a big deal a while back because even Samsungs own folio case has magnets)
note that not everyone reported the issues so I'm pretty sure it has to do with how strong the magnet in the case is.
if you use your pen a lot I would stay away from those cases.
on the other hand if you don't use the pen then it wont affect you.
There are apps to let you double tap the screen to wake it (even for android versions before it was supported) which would save the physical buttons some wear but I suspect you would take a hit on battery life with that option.
The answer to just about everything: Tasker.
There's a how-to for this particular setting here. Battery drain is pretty low, about 2% every 12 hours or so.
Only flip covers with a magnet can use the system's inbuild auto-on/off functionality. Everything else needs to use the proximity sensor.
There are three types of flip covers, two of which use a magnet.
One is a strong, single magnet. This is the cheap option and causes problems with the Wacom sensors, which are also magnetic. You'll find this in pretty much 90% of all auto-on/off covers, especially the cheaper ones. The first Samsung covers also used this method, until they figured out it was a terrible idea.
The second is a ring patterns of thin magnetic strip woven through the entire back of the cover. This is used by most expensive brands (Like Samsonite), and doesn't interfere with the Wacom sensor.
The third are the most common one: Covers without a magnet. All these do is protect your screen.
ShadowLea said:
The answer to just about everything: Tasker.
There's a how-to for this particular setting here. Battery drain is pretty low, about 2% every 12 hours or so.
Only flip covers with a magnet can use the system's inbuild auto-on/off functionality. Everything else needs to use the proximity sensor.
There are three types of flip covers, two of which use a magnet.
One is a strong, single magnet. This is the cheap option and causes problems with the Wacom sensors, which are also magnetic. You'll find this in pretty much 90% of all auto-on/off covers, especially the cheaper ones. The first Samsung covers also used this method, until they figured out it was a terrible idea.
The second is a ring patterns of thin magnetic strip woven through the entire back of the cover. This is used by most expensive brands (Like Samsonite), and doesn't interfere with the Wacom sensor.
The third are the most common one: Covers without a magnet. All these do is protect your screen.
Click to expand...
Click to collapse
Can I use Macrodroid? And how?
Related
I owned a smart cover for my galaxy note 8.0, it can work properly like sleep and wake.
But here's the problem come,
usually the cover is cover the front of the tablet, but when we use it, we will flip the cover to the back of tablet.
while the cover touched the back side of the tablet, it will also put it as sleep.
so, how to disable smart cover auto sleep?
i had tried the "Lock instantly with power key", but it required at least security of "pattern"
Any ideas?
Need help! THANK YOU!:good:
I guess something is wrong either with your cover or device - putting the cover on the back should never put the device to sleep.
I don't recall anybody reporting similar problems here, also the small sample we have at home (2 notes + 2 covers) behaves correctly.
The best thing (although it's probably easier said than done) would be to establish which one is malfunctioning and have it replaced if possible.
otoh I would also be interested in a way to disable the cover on/off function - mine is so sensitive, that even the slight move of the front part wakes the device, causing increased battery drain and making betterbatterystats readings useless.
p107r0 said:
I guess something is wrong either with your cover or device - putting the cover on the back should never put the device to sleep.
I don't recall anybody reporting similar problems here, also the small sample we have at home (2 notes + 2 covers) behaves correctly.
The best thing (although it's probably easier said than done) would be to establish which one is malfunctioning and have it replaced if possible.
otoh I would also be interested in a way to disable the cover on/off function - mine is so sensitive, that even the slight move of the front part wakes the device, causing increased battery drain and making betterbatterystats readings useless.
Click to expand...
Click to collapse
Here's a YouTube video that shows you how to do that:
https://www.youtube.com/watch?v=GhB5kJGQKsI
exibm said:
Here's a YouTube video that shows you how to do that:
https://www.youtube.com/watch?v=GhB5kJGQKsI
Click to expand...
Click to collapse
thanks, but that's not it, my problem is sensitivity to magnets in the cover, not the home button
Sent from my GT-N5100 using xda premium
Yes I have the same problem... I bought some dodgy case off eBay. The magnets also interfee with the spen
Sent from my GT-N5110 using Tapatalk 4 Beta
I have seen that happen a lot with ipad cases. Its due to a poorly designed case.
flashlim said:
I owned a smart cover for my galaxy note 8.0, it can work properly like sleep and wake.
But here's the problem come,
usually the cover is cover the front of the tablet, but when we use it, we will flip the cover to the back of tablet.
while the cover touched the back side of the tablet, it will also put it as sleep.
so, how to disable smart cover auto sleep?
i had tried the "Lock instantly with power key", but it required at least security of "pattern"
Any ideas?
Need help! THANK YOU!:good:
Click to expand...
Click to collapse
p107r0 said:
thanks, but that's not it, my problem is sensitivity to magnets in the cover, not the home button
Sent from my GT-N5100 using xda premium
Click to expand...
Click to collapse
It happens all the time to me. Put it nicely in the back. Not a single bit cover the front. Shake the device a little bit. The cover hits the back of the device, make some noise and screen turns off. Magic. As if the device can sense magnet even by its back. But when it sits really tightly that no space bw it and the case, problem solved by put on some sticky tape in the back.
Smart cover not smart at all T^T~ but original case without having that problem right?
Smart cover problem
Still looking for a way to disable the software that causes auto sleep/wake.
The problem with some covers is that they are not authentic from the manufacturers. The original Samsung case for Note 8/N5100 has the correct magnetic power in the case flap. The other covers have a magnet that is too strong so when the flap is in the back the magnet still effects.
I surgically cut the magnet out of the cheep cover and closed it back up. Disabled auto wake with the modification. I am guessing the same could be done with the original authentic Samsung case but it is hard to cut the little magnet out because its built in seamlessly so you cant see the exact location of the magnet.
flashlim said:
Smart cover not smart at all T^T~ but original case without having that problem right?
Click to expand...
Click to collapse
Original Samsung book cover should not have that problem. i have been using the book cover for almost five months and not facing said issue.
I was experiencing random screen shutoffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
Questions: I was wondering if anyone else has experienced similar issues with their cases/covers (a little research seems to indicate this is not an isolated issue and many, if not all, cases/covers suffer from this issue).
1) If you have not, which cases/covers do you use? Do these cases resolve the issue by never aligning the cover to the same position when flipped backwards as when flipped forwards (i.e. skewed slightly short of the edge when in backwards position)?
2) If you have experienced this issue, how have you addressed it? Can you disable the magnetic sensor?
3) Would weakening the magnet in the case perhaps ensure that it was only sensed in the forward position?
SKida00 said:
I was experiencing random screen sback andk ffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
et in the case perhaps ensure that it was only sensed in the forward position?
Click to expand...
Click to collapse
yes i have the same problem. pick up A generic folio type case for my P600. Case looks and feels great. Auto wake works brilliantly when I open the cover, but there is the problem of The screen turning off when I flip the cover over to the back and the magnetic edges meet. Dunno how to fix this yet. Tried the magnetoff xposed module but that doesn't seem to work.
I got the Moko slim case and the same thing happens, what I did to circumvent the problem was to put my screen cleaning cloth between the case and the tablet. This prevents the magnet from locking the screen when completely folded backwards, the only thing is that this method will block the camera with the cloth. For me this is not a problem I don't see myself using the camera on my tablet when I can use my SGS3's camera, and this way I never forget my screen cleaning cloth .
I've read about this on other devices on various covers as well. they think it mah be due to the magnet not being properly shielded. dunno any fixes other than get another case.
I hade a cover for my old Ipad and it all so turn off the Ipad when I flipped over the cover.
It did turn out the problem was with the magnet and after getting a new one, the problem was solved.
My poetic slimline work perfectly no issues at all. Love the look and feel, I do want a carry slevee tho for more protection if I wanna bring it out of the house. Or even just to store in the house. But overall love this case.
Sent from my SM-P600 using Tapatalk
Get a piece of sheet metal (strip out a cheapie magnetic whiteboard , a few dollars at a variety store) cut to just less than the back of the tablet screen.
Cover it with a thin plastic film (to safeguard from cutting yourself)
It will adhere to the back of the screen magnetically and flatten the magnet's field
Now you can use the device with the keyboard tucked away behind the screen. (you may have to leave a small air gap say 5mm to 10 mm)
This does not affect the normal screen-keyboard functions when used conventionally
Same problem with Galaxy Tab A (Nougat)
There is an option in the tab to turn it off, but regardless what you choose, the tablet still responds to the magnet. Very annoying when you lay down your tablet flat. For now i just put something between the cover and the back of the tablet, like a handkerchief. This works for me, but ofcourse it's not a solution just a workaround. I'm still trying to find a solution.
Did you find any way to turn off the magnetic lock and unlock function? When I backfold my cover (aftermarket), it automatically locks my tab. Which is very irritating. I have Samsung galaxy tab S5e
There wasn't a good search result on a way to disable it via software or hardware mod so I thought I would post the solution I just did on my daughter's new tablet folio.
She has an old S3 Tab so the options are quite limited so figured modification was the only way. I ended up removing 3 magnets until I figured out which one actually did the on/off Hall effect. The smart thing to do would have been to use a magnet to find where on the tablet the Hall effect sensor was first, then remove just that magnet. The other magnets are for holding the clasp in place when the folio is open or closed.
I just cut an X over the magnet location, removed it, then filled it back in with hot glue. On her tablet, the Hall sensor was on the top left (fat arrow). It's annoying to have to do this but there's no other way. I tried the metal plate trick but that looked pretty bad and didn't always work.
Hope that helps someone
I have a book cover my my Note 10 2014, and I find the smartcover behavior not so "smart". It is, in fact, extremely stupid and turns the screen on and off at completely random times. I don't have the same problem when it is off the cover. Props for Samsung for figuring out how to make it sense that it is in the cover (it is not just a light sensor) but the "smart" part of the feature is rather frustrating, and at times infuriating.
Thanks!
Perhaps try exchanging covers? Mine works perfectly and is the best accessory I could have bought for it (even paid less than MSRP).
Hah. I paid $10 for mine, from China. Maybe that's why it doesn't work so well. Still, there really ought to be a way to disable way to disable any sort of "automatic" feature. For example, it is very easy to disable Smart Stay, Smart Scroll, Smart Pause, automatically connect to wifi, S Beam, NFC, and so on and so forth. All (or most?) of which are on from factory...
Zaruski said:
I have a book cover my my Note 10 2014, and I find the smartcover behavior not so "smart". It is, in fact, extremely stupid and turns the screen on and off at completely random times. I don't have the same problem when it is off the cover. Props for Samsung for figuring out how to make it sense that it is in the cover (it is not just a light sensor) but the "smart" part of the feature is rather frustrating, and at times infuriating.
Thanks!
Click to expand...
Click to collapse
Are you using an original Samsung book cover? Some third-party book covers don't have proper magnetic shielding at the front so when you flip it over it affects the screen on-off function of the tablet.
Is there a way to TEMPORARILY disable the proximity sensing of the double-tap wake feature of LG G3?
What I want is to be able to wake the phone and unlock it while the phone is in a transparent case (waterproof bike mount, armband, etc.). The phone currently thinks that it is in the pocket and does not wake on double-tap on the screen.
The power button is in the center of the back of the phone which makes it hard/impossible to reach/find when in such a case/armband.
Is there a hidden setting or an app that will make this possible? And once more - I need this for temporary situations when riding a bike. After riding a bike i'd like to re-enable the proximity sensing for pocket carrying.
sstundzia said:
Is there a way to TEMPORARILY disable the proximity sensing of the double-tap wake feature of LG G3?
What I want is to be able to wake the phone and unlock it while the phone is in a transparent case (waterproof bike mount, armband, etc.). The phone currently thinks that it is in the pocket and does not wake on double-tap on the screen.
The power button is in the center of the back of the phone which makes it hard/impossible to reach/find when in such a case/armband.
Is there a hidden setting or an app that will make this possible? And once more - I need this for temporary situations when riding a bike. After riding a bike i'd like to re-enable the proximity sensing for pocket carrying.
Click to expand...
Click to collapse
Cut out a small hole in the plastic right where the sensor is. That's how I solved the same problem.
infinitron said:
Cut out a small hole in the plastic right where the sensor is.
Click to expand...
Click to collapse
"waterproof bike mount" :good:
Automaton locker might have a setting that will help you.
https://play.google.com/store/apps/details?id=aky.akshay.coveralgorithm
Sent from my LG-D855 using Tapatalk
The OP has probably solved his problem in the meantime. I had much the same issue, and I wanted to share what I did.
Firstly, yes, there is a way to "disable" the proximity sensor: just cover it with something that a) does not emit, and b) does not reflect IR light. Because of a), a finger does not work, but a piece of black sticky tape does. If only the right of the two little lenses is covered (that is the IR LED), the ambient light sensor even continues to work.
Of course, putting on some sticky tape whenever I use my G3 in the bicycle-mounted case is not the ideal solution. So I experimented with sticking the tape to the inside of the case. That did not work too well, because the front of the case is flexible and never lies flush on zthe screen. I ended up putting some thicker, spongy rubber there.
All this was with Rixen & Kaul's Phonebag M, which otherwise worked very nicely and allowed me to use my previous phone for navigation even in the most torrential rain.
But that spongy rubber blob made the touchscreen more difficult to use, as it lifted the case's transparent front even further away from the screen. So I kept looking, and bought Topeak's new Drybag 6.
It's a bit too big for an L3, but the Drybag 5 seems to *just* be too small - you'd probably get an L3 in there, but not out again. So the size 6 is the better choice. The interesting thing is that Topeak seems to use a different material for the transparent front: it seems to reflect IR light a lot less than the Phonebag's, so I can switch on my L3 almost every time (I'd say, 95% of my attempts worked). I will keep testing it for a few more weeks.
Two other things I find nice about it: the bicycle mount doubles as a belt clip, and it has a ziplock-style - um - ziplock, so it's probably not just resisting rain and sweat, but really waterproof. When I closed the ziplock, it was air-tight.
What I don't really like about it is the flimsiness of the mount - even the screw is plastic, and the case has a lot of play in the mount. I don't think, though, that it can fall out, even on bad roads.
Hope I could help someone.
Cheers
Daniel
New owner here.
The 10.1 manual says:
"Do not cover the antenna area with your hands or other objects. This may cause
connectivity problems or drain the battery.
Do not use a screen protector. This causes sensor malfunctions"
Obviously lots of folks on here are using one and/or both of these. Have you found the malfunctions that the manual says will happen? I'd really like to protect my tablet, but don't want to cause a problem with it. Thanks.
A screen protector designed for your device is fine. They actually have a hole over the proximity sensor. I have two cases, a keyboard case and a pro case both designed for my Note. They are just fine as long as the are designed for your device. The slots and holes around the case are not random, they are there so as to insure the device functions correct.