Develop Bugs

Mode Fastboot doesn´t detect Htc Desire usb

Hey, I did a S-Off mode to Htc Desire However it installed a recovery program different which doesn´t like me and I back to amon-ra recovery, and my big surprise is when I try to change Splash for Adb or Android flasher (both running on fastboot mode) my htc desire isn´t recognised however in android system the usb is recognised but don´t recognised in fastboot mode , I don´t use for change splash1, somebody can help me? Thanks for all
Pardon for my poor english

Do you have hboot drivers installed? If not that's your problem.
Sent from my HTC Desire using XDA App

In this moment I have formatted pc, and the firs step I have done is installing hboot driver and the problem coming , Where is the problem? help me please!! Thanks for all

usb-brick?
Hi there,
same thing happened to me since I upgraded to oxygen 2 last week. It does look like a usb-brick, however radio, bluetooth and sd (reading music, storing pic from camera) work..
Once plug to my pc, the phone charges but no notification about mounting the sd pops up. Sd is not recognize, I tryed to mount it manually (android booted and through clockwork), via a dedicated apps (like automount ...)n nothing fugging work.
Wanted to use the usb fix from modaco and also listed here, however the phone is not recognize in fastboot (no fastboot usb). I have reinstalled, adk, htc sync, java ... and nothing fugging work.
Any leads on what happening would be much appreciated.
Cheers.

Do you get mend it?

same thing happend to me

ebi023 said:
same thing happend to me
Click to expand...
Click to collapse
To me too
that´s a snippet from my dmesg log
Code:
<4>[ 733.389221] samsung_oled_panel_init()
<6>[ 733.456909] capella_cm3602_ioctl cmd 2
<6>[ 733.457305] capella_cm3602_disable
<6>[ 733.457702] capella_cm3602_disable: already disabled
<6>[ 733.458526] capella_cm3602_ioctl cmd 1
<6>[ 733.458923] lightsensor_ioctl set value = 1
<6>[ 733.459289] lightsensor_enable
<3>[ 733.459991] lightsensor_enable: microp is suspended
<6>[ 733.460388] lightsensor_ioctl get enabled status: 1
<6>[ 733.540222] gpio_keys_scan_keys: key 1-74, 0 (94) changed to 0
<6>[ 733.703613] msmfb: ready, waiting for full update
<6>[ 733.704040] bravo_ts_power: power 1
<6>[ 733.733581] msmfb: pan_update in state(1)
<6>[ 733.733612] msmfb: full update starting
<6>[ 733.757202] msmfb: pan_update in state(3)
<6>[ 733.766235] msmfb: full update completed
<6>[ 733.766357] msmfb: turning on panel
<6>[ 733.766387] lcdc_unblank: ()
<4>[ 733.766387] amoled_panel_unblank
<4>[ 733.774383] amoled_panel_unblank: last_val = 80
<4>[ 733.850677] wlan: power active. usb_type:2
<4>[ 733.857666] wlan: update dtim listern interval: 0
<7>[ 733.858825] __capella_cm3602_power: Turn the capella_cm3602 power on
<3>[ 733.859527] curcial_oj_late_resume: enter
<3>[ 733.866485] curcial_oj_poweron:OJ power enable(1)
<6>[ 734.040832] OpticalJoystick Device ID: 0d
<6>[ 734.044677] OJ Driver: Revision : 02
<6>[ 734.049438] [R] late_resume end
<6>[ 734.648437] [email protected], 3810
<7>[ 734.676391] ALS value: 0x0, level: 1 #
<7>[ 734.687530] ALS value: 0x0, level: 1 #
<6>[ 734.890747] [email protected], 6493
<6>[ 734.983581] capella_cm3602_ioctl cmd 1
<6>[ 734.983581] lightsensor_ioctl get enabled status: 1
<6>[ 734.990692] __spi_bma150_set_mode: BMA get into NORMAL mode!
<4>[ 739.800750] Division by zero in kernel.
<4>[ 739.800933] Function entered at [<c002e948>] from [<c01bfb3c>]
<4>[ 739.801239] Function entered at [<c01bfb3c>] from [<c02629b0>]
<4>[ 739.801391] Function entered at [<c02629b0>] from [<c006fb38>]
<4>[ 739.801696] Function entered at [<c006fb38>] from [<c00732c4>]
<4>[ 739.801849] Function entered at [<c00732c4>] from [<c002a99c>]
<6>[ 739.827331] batt: 80%, 4079 mV, 404 mA (539 avg), 27.5 C, 1086 mAh
<6>[ 747.659454] cable_status_update: status=0
<6>[ 747.660186] msm_hsusb_set_vbus_state: 0
<6>[ 747.660614] hsusb: ONLINE -> OFFLINE
<6>[ 747.660949] usb: lpm exit
<6>[ 747.670135] batt: charging OFF
<6>[ 747.678588] usb: notify offline
<6>[ 747.678955] bravo_usb_phy_reset
<6>[ 747.679290] msm_hsusb_phy_reset
<6>[ 747.738281] usb: lpm enter
<6>[ 747.738403] usb_suspend_phy
<6>[ 747.739624] usb: send connect type 0
<6>[ 747.739715] fsg_set_ums_state: 0
<4>[ 747.739929] ### notify_usb_connected(0) ###
<6>[ 748.843475] cable_status_update: status=1
<6>[ 748.868286] msm_hsusb_set_vbus_state: 1
<6>[ 748.868988] hsusb: OFFLINE -> ONLINE
<6>[ 748.869323] usb: lpm exit
<6>[ 748.870758] hsusb: reset controller
<6>[ 748.877838] batt: charging SLOW
<6>[ 748.908477] bravo_usb_phy_reset
<6>[ 748.908874] msm_hsusb_phy_reset
<6>[ 749.118438] msm72k_udc: ulpi: write 0x0c to 0x31
<6>[ 749.118652] msm72k_udc: ulpi: write 0x31 to 0x32
<6>[ 749.118774] msm72k_udc: ulpi: write 0x1d to 0x0d
<6>[ 749.118957] msm72k_udc: ulpi: write 0x1d to 0x10
<6>[ 749.119110] usb: notify offline
<6>[ 749.119232] msm_hsusb: enable pullup
<6>[ 749.138397] usb: AC charger
<6>[ 749.158477] usb: lpm enter
<6>[ 749.158599] usb_suspend_phy
<6>[ 749.159790] usb: send connect type 2
<6>[ 749.160003] fsg_set_ums_state: 2
<4>[ 749.160095] ### notify_usb_connected(2) ###
<6>[ 749.167480] batt: charging FAST
<6>[ 750.570068] sudden key ignore
<6>[ 750.577270] sudden key ignore
<6>[ 750.584808] sudden key ignore
<6>[ 750.592163] sudden key ignore
<6>[ 750.599548] sudden key ignore
<6>[ 750.606872] sudden key ignore
<6>[ 778.073272] capella_cm3602_ioctl cmd 1
<6>[ 778.073455] lightsensor_ioctl get enabled status: 1
<6>[ 778.161499] __spi_bma150_set_mode: BMA get into SLEEP mode!
<6>[ 791.238342] batt: 80%, 4089 mV, 423 mA (415 avg), 27.6 C, 1091 mAh
<6>[ 798.738037] capella_cm3602_ioctl cmd 1
<6>[ 798.738159] lightsensor_ioctl get enabled status: 1
<6>[ 798.753601] __spi_bma150_set_mode: BMA get into NORMAL mode!
<6>[ 802.085937] capella_cm3602_ioctl cmd 1
<6>[ 802.085937] lightsensor_ioctl get enabled status: 1
<6>[ 802.271789] __spi_bma150_set_mode: BMA get into SLEEP mode!
<6>[ 808.274749] cable_status_update: status=0
<6>[ 808.275482] msm_hsusb_set_vbus_state: 0
<6>[ 808.275909] hsusb: ONLINE -> OFFLINE
<6>[ 808.276245] usb: lpm exit
<6>[ 808.288330] usb: notify offline
<6>[ 808.288757] bravo_usb_phy_reset
<6>[ 808.289123] msm_hsusb_phy_reset
<6>[ 808.289611] batt: charging OFF
<6>[ 808.348266] usb: lpm enter
<6>[ 808.348266] usb_suspend_phy
<6>[ 808.349365] usb: send connect type 0
<6>[ 808.349365] fsg_set_ums_state: 0
<4>[ 808.349365] ### notify_usb_connected(0) ###
<6>[ 809.500976] cable_status_update: status=1
<6>[ 809.528320] msm_hsusb_set_vbus_state: 1
<6>[ 809.529022] hsusb: OFFLINE -> ONLINE
<6>[ 809.529357] usb: lpm exit
<6>[ 809.530822] hsusb: reset controller
<6>[ 809.538848] batt: charging SLOW
<6>[ 809.568450] bravo_usb_phy_reset
<6>[ 809.568847] msm_hsusb_phy_reset
<6>[ 809.778442] msm72k_udc: ulpi: write 0x0c to 0x31
<6>[ 809.778717] msm72k_udc: ulpi: write 0x31 to 0x32
<6>[ 809.778839] msm72k_udc: ulpi: write 0x1d to 0x0d
<6>[ 809.779052] msm72k_udc: ulpi: write 0x1d to 0x10
<6>[ 809.779205] usb: notify offline
<6>[ 809.779327] msm_hsusb: enable pullup
<6>[ 809.798339] usb: AC charger
<6>[ 809.818359] usb: lpm enter
<6>[ 809.818542] usb_suspend_phy
<6>[ 809.821197] usb: send connect type 2
<6>[ 809.821502] fsg_set_ums_state: 2
<4>[ 809.821655] ### notify_usb_connected(2) ###
<6>[ 809.829315] batt: charging FAST
<7>[ 814.113616] ALS value: 0x6, level: 1 #
<7>[ 815.128906] ALS value: 0x0, level: 1 #
<6>[ 828.444671] capella_cm3602_ioctl cmd 1
<6>[ 828.444885] lightsensor_ioctl get enabled status: 1
<6>[ 828.453491] __spi_bma150_set_mode: BMA get into NORMAL mode!
<6>[ 841.308776] batt: 81%, 4084 mV, 420 mA (346 avg), 28.5 C, 1097 mAh
I hope somebody can help
greetings

I have the same problem, phone is attempting to be repaired but I doubt they can fix it.
Had water damage at my usb connector, which i though was the cause but issue still exists after being fixed.
downgraded hboot
flashed stock ruu via PB99IMG.zip method
attempted various methods of the mtd0.img fix

still broken dam usb
Hi,
Got my phone back... but still not joy after they replaced usb connector.
Still have the same issue, but now I have no root (using visionary+ for temp root) and s-on.
Issue : PC unable to connect\detect to desire in hboot/fastboot/normal operations ie... not device detected.
Ps... i think issue occurred after doing oxygen rom as well
Code:
<6>[14908.060607] SMEM_APPS_DEM_SLAVE_DATA: 35s 2010000 0 0 1 0 30100000 2 RPCCA
LL 5c
<6>[14908.060607] wakeup wake lock: SMD_RPCCALL
<6>[14908.060882] perflock_notifier_call: cpufreq recover policy 245000 998400
<6>[14908.061248] batt: M2A_RPC: cable_update: USB at 14895032896089 (2011-02-25
07:39:19.574920653 UTC)
<6>[14908.061523] batt: htc_cable_status_update: 0 -> 1
<6>[14908.061798] msm_hsusb_set_vbus_state: 1
<6>[14908.061950] hsusb: OFFLINE -> ONLINE
<6>[14908.062103] usb: lpm exit
<6>[14908.063812] hsusb: reset controller
<6>[14908.063934] [HTC_BATT] cable change to 1
<6>[14908.064025] batt: ds2784_notify: 0 1 at 14895035734223 (2011-02-25 07:39:1
9.577697752 UTC)
<6>[14908.064331] batt: charger ON (SLOW) at 14895035947846 (2011-02-25 07:39:19
.578002928 UTC)
<4>[14908.068084] Restarting tasks ... done.
<6>[14908.073272] sleep_stat.2: 12966403s 10991 12944611s 10643 - 0 13 207 - 0 0
- 0 0 0 0 0(2011-02-25 07:39:23.505737305 UTC)
<6>[14908.073455] suspend: exit suspend, ret = 0 (2011-02-25 07:39:23.505950928
UTC)
<6>[14908.073669] [R] resume end
<6>[14908.073760] [R] suspend start
<6>[14908.073883] suspend: abort suspend
<6>[14908.074066] active wake lock vbus_present
<6>[14908.098663] bravo_usb_phy_reset
<6>[14908.098785] msm_hsusb_phy_reset
<6>[14908.308624] msm72k_udc: ulpi: write 0x0c to 0x31
<6>[14908.309265] msm72k_udc: ulpi: write 0x31 to 0x32
<6>[14908.309600] msm72k_udc: ulpi: write 0x1d to 0x0d
<6>[14908.310211] msm72k_udc: ulpi: write 0x1d to 0x10
<6>[14908.310607] usb: notify offline
<6>[14908.310943] msm_hsusb: enable pullup
<6>[14908.314575] msm72k_udc: usb: suspend
<6>[14908.328582] usb: not AC charger
<6>[14908.628723] usb: send connect type 3
<6>[14908.629364] fsg_set_ums_state: 1
<6>[14908.629699] ums: set state 1
<6>[14908.638214] batt:online=1
<6>[14908.639617] [HTC_BATT] cable change to 1
<6>[14908.640563] batt: ds2784_notify: 0 1 at 14895612394381 (2011-02-25 07:39:2
4.073028566 UTC)
<6>[14908.641265] batt: charger ON (SLOW) at 14895613370943 (2011-02-25 07:39:24
.073730470 UTC)
<6>[14908.921600] request_suspend_state: wakeup (3->0) at 14895893064561 (2011-0
2-25 07:39:24.354064957 UTC)
<6>[14908.921936] [R] late_resume start
<6>[14908.922058] lcdc_resume: resuming
<4>[14908.922180] samsung_oled_panel_init()
<6>[14908.990783] capella_cm3602_ioctl cmd 2
<6>[14908.990905] capella_cm3602_disable
<6>[14908.991027] capella_cm3602_disable: already disabled
<6>[14908.991210] capella_cm3602_ioctl cmd 1
<6>[14908.991332] lightsensor_ioctl set value = 1
<6>[14908.991516] lightsensor_enable
<3>[14908.991607] lightsensor_enable: microp is suspended
<6>[14908.991729] lightsensor_ioctl get enabled status: 1
<6>[14909.233154] msmfb: ready, waiting for full update
<6>[14909.233489] bravo_ts_power: power 1
<6>[14909.256652] msmfb: pan_update in state(1)
<6>[14909.256652] msmfb: full update starting
<6>[14909.267913] msmfb: pan_update in state(3)
<6>[14909.283782] msmfb: full update completed
<6>[14909.283874] msmfb: turning on panel
<6>[14909.283874] lcdc_unblank: ()
<4>[14909.283905] amoled_panel_unblank
<4>[14909.291503] amoled_panel_unblank: last_val = 90
<4>[14909.388610] wlan: power active. usb_type:3
<4>[14909.401947] wlan: update dtim listern interval: 0
<7>[14909.402648] __capella_cm3602_power: Turn the capella_cm3602 power on
<6>[14909.402679] sleep_stat.3: 12966403s 10991 12944611s 10643 - 0 13 207 - 0 0
- 0 0 0 0 0(2011-02-25 07:39:24.835144068 UTC)
<3>[14909.402709] curcial_oj_late_resume: enter
<3>[14909.404449] curcial_oj_poweron:OJ power enable(1)
<6>[14909.490234] OpticalJoystick Device ID: 0d
<6>[14909.496704] OJ Driver: Revision : 02
<6>[14909.501617] [R] late_resume end
<7>[14910.205230] ALS value: 0x0, level: 1 #
<7>[14910.214782] ALS value: 0x0, level: 1 #
<6>[14910.389862] [email protected], 4749
<6>[14910.729736] [email protected], 6441
<6>[14922.707183] capella_cm3602_ioctl cmd 1
<6>[14922.707305] lightsensor_ioctl get enabled status: 1
<6>[14922.719879] __spi_bma150_set_mode: BMA get into NORMAL mode!
<6>[14930.603973] capella_cm3602_ioctl cmd 1
<6>[14930.604187] lightsensor_ioctl get enabled status: 1
<6>[14930.631195] __spi_bma150_set_mode: BMA get into SLEEP mode!
<6>[14937.077880] [HTC_BATT]RSNSP=67,RARC=81,Vol=4016mV,Current=136mA,Temp=322C(
1/10)
<6>[14937.078247] batt: charging SLOW
<3>[14952.175964] init: sys_prop: Unable to stop service ctl [adbd] uid: 10093 p
id:4900
<3>[14952.188079] init: sys_prop: permission denied uid:10093 name:service.adb.
tcp.port
<3>[14952.199890] init: sys_prop: Unable to start service ctl [adbd] uid: 10093
pid:4902
<6>[14965.169830] disabling adb
<6>[14965.170013] hsusb: ONLINE -> RESET
<6>[14965.170135] msm_hsusb: disable pullup
<6>[14965.170257] hsusb: reset controller
<6>[14965.170654] adb_release
<6>[14965.208709] bravo_usb_phy_reset
<6>[14965.208862] msm_hsusb_phy_reset
<6>[14965.418609] msm72k_udc: ulpi: write 0x0c to 0x31
<6>[14965.418823] msm72k_udc: ulpi: write 0x31 to 0x32
<6>[14965.418914] msm72k_udc: ulpi: write 0x1d to 0x0d
<6>[14965.419097] msm72k_udc: ulpi: write 0x1d to 0x10
<6>[14965.419250] usb: notify offline
<6>[14965.419372] msm_hsusb: enable pullup
<6>[14965.419555] hsusb: RESET -> ONLINE
<6>[14965.422576] msm72k_udc: usb: suspend
<7>[14973.482391] ALS value: 0xC, level: 1 #
<7>[14975.492218] ALS value: 0x0, level: 1 #
<6>[14987.178466] [HTC_BATT]RSNSP=67,RARC=81,Vol=4021mV,Current=137mA,Temp=325C(
1/10)
Using ADB Wireless to get access to phone... but need to work out how to root my HBOOT 93.xxx
Can downgrade I guess to 83.xx but not sure if that will help

When you formatted your PC you htc sync drivers are also deleted. My desire had also problems with not getting recognized because I never had installed htc sync when going to windows 7 ultimate. After install en delete of htc sync (drivers stay in place) I never had any issues with recognising.

[Request] Mount usb flash drive ( OTG )

Hi
I updated my phone to 4.0.A.2.368 FW . now my device detected Flash Memory but not mount it
<6>[ 570.560455] usb 1-1: Product: Storage Media
<6>[ 570.560485] usb 1-1: Manufacturer: Sony
<6>[ 570.560516] usb 1-1: SerialNumber: 5A10042782776
can any one help me to mount it ?

[Q] USB Host Mode Failure

Anyone else have a problem with USB host mode and copying big files?
If so, can we fix this?
I have tried formatting my drive in FAT32,NTFS, and ext2. But the result is always the same, the drive dies if I copy a file bigger than 30 or 40 MB. I have tried stock, Faux123, and francoKernel as well.
The drive doesn't die at a specific MB each time, but it is generally around 30 MB but sometimes makes it to 80 or even 140 MB one time. I am trying to off-load some 700MB movies.
Here is the kernel message error:
<6>[ 1920.842529] max17040 4-0036: online = 1 vcell = 3547500 soc = 22 status = 3 health = 1 temp = 370 charger status = 0
<3>[ 1926.574005] EXT4-fs (sda1): Unrecognized mount option "fmask=0702" or missing value
<3>[ 1926.594299] EXT4-fs (sda1): Unrecognized mount option "fmask=0702" or missing value
<3>[ 1926.649810] EXT4-fs (sda1): Unrecognized mount option "fmask=0702" or missing value
<3>[ 1927.740753] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities
<6>[ 1927.773895] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
<6>[ 1927.938781] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
<3>[ 1968.389251] L3 CUSTOM SRESP error with SOURCEMM2 info=0x84
<4>[ 1968.389434] ------------[ cut here ]------------
<4>[ 1968.389739] WARNING: at arch/arm/mach-omap2/omap_l3_noc.c:130 l3_interrupt_handler+0x31c/0x360()
<4>[ 1968.390045] L3 custom sresp error
<4>[ 1968.390197] Modules linked in:
<4>[ 1968.390686] [<c0055de4>] (unwind_backtrace+0x0/0xf8) from [<c00983a8>] (warn_slowpath_common+0x4c/0x64)
<4>[ 1968.390991] [<c00983a8>] (warn_slowpath_common+0x4c/0x64) from [<c0098454>] (warn_slowpath_fmt+0x30/0x40)
<4>[ 1968.391326] [<c0098454>] (warn_slowpath_fmt+0x30/0x40) from [<c0074898>] (l3_interrupt_handler+0x31c/0x360)
<4>[ 1968.391632] [<c0074898>] (l3_interrupt_handler+0x31c/0x360) from [<c00d45fc>] (handle_irq_event_percpu+0x50/0x178)
<4>[ 1968.391967] [<c00d45fc>] (handle_irq_event_percpu+0x50/0x178) from [<c00d4760>] (handle_irq_event+0x3c/0x5c)
<4>[ 1968.392150] [<c00d4760>] (handle_irq_event+0x3c/0x5c) from [<c00d6aec>] (handle_fasteoi_irq+0xbc/0x164)
<4>[ 1968.392456] [<c00d6aec>] (handle_fasteoi_irq+0xbc/0x164) from [<c00d3f50>] (generic_handle_irq+0x2c/0x40)
<4>[ 1968.392791] [<c00d3f50>] (generic_handle_irq+0x2c/0x40) from [<c004904c>] (asm_do_IRQ+0x4c/0xac)
<4>[ 1968.393096] [<c004904c>] (asm_do_IRQ+0x4c/0xac) from [<c004eb08>] (__irq_svc+0x48/0xe4)
<4>[ 1968.393402] Exception stack(0xc0799f28 to 0xc0799f70)
<4>[ 1968.393554] 9f20: c0799f70 3b9aca00 4c534d85 000001ca 4c4bda2c 000001ca
<4>[ 1968.393859] 9f40: 000003ff c1192210 8000406a 412fc09a 00000000 00000000 00000000 c0799f70
<4>[ 1968.394042] 9f60: c007c690 c0068380 00000013 ffffffff
<4>[ 1968.394348] [<c004eb08>] (__irq_svc+0x48/0xe4) from [<c0068380>] (omap4_enter_idle_wfi+0x48/0xd4)
<4>[ 1968.394683] [<c0068380>] (omap4_enter_idle_wfi+0x48/0xd4) from [<c03af838>] (cpuidle_idle_call+0x94/0x118)
<4>[ 1968.394989] [<c03af838>] (cpuidle_idle_call+0x94/0x118) from [<c0050538>] (cpu_idle+0xbc/0xfc)
<4>[ 1968.395172] [<c0050538>] (cpu_idle+0xbc/0xfc) from [<c00088ac>] (start_kernel+0x298/0x2e8)
<4>[ 1968.395477] [<c00088ac>] (start_kernel+0x298/0x2e8) from [<80008040>] (0x80008040)
<4>[ 1968.395782] Board Information: Tuna HW revision: 09 (Maguro 8th Sample), cpu OMAP4460 ES1.1
<4>[ 1968.396087] ---[ end trace 33de6ebe35ad56b6 ]---
<6>[ 1970.874023] max17040 4-0036: online = 1 vcell = 3532500 soc = 22 status = 3 health = 1 temp = 380 charger status = 0
<6>[ 1993.138793] usb 1-1: reset high speed USB device number 2 using musb-hdrc
<6>[ 2000.347503] fsa9480 4-0025: cable detect change, from 'usb-host' to 'unknown/none'
<6>[ 2000.347717] usb 1-1: USB disconnect, device number 2
<4>[ 2000.350708] fsa9480 4-0025: irq fired, but nothing happened
<6>[ 2000.351989] fsa9480 4-0025: nothing attached, keeping ownership of port
<6>[ 2001.361236] max17040 4-0036: online = 1 vcell = 3585000 soc = 21 status = 2 health = 1 temp = 380 charger status = 0
<6>[ 2003.287322] sd 0:0:0:0: Device offlined - not ready after error recovery
<6>[ 2003.287597] sd 0:0:0:0: [sda] Unhandled error code
<6>[ 2003.287628] sd 0:0:0:0: [sda] Unhandled error code
<6>[ 2003.287658] sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
<6>[ 2003.287689] sd 0:0:0:0: [sda] CDB: cdb[0]=0x2a: 2a 00 00 00 00 3f 00 00 08 00
<3>[ 2003.287719] end_request: I/O error, dev sda, sector 63
<3>[ 2003.287750] Buffer I/O error on device sda1, logical block 0
<4>[ 2003.287780] lost page write due to I/O error on sda1
<6>[ 2003.289154] sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
<6>[ 2003.289459] sd 0:0:0:0: [sda] CDB: cdb[0]=0x2a: 2a 00 00 00 21 e7 00 00 08 00
<3>[ 2003.291625] end_request: I/O error, dev sda, sector 8679
<3>[ 2003.291778] Buffer I/O error on device sda1, logical block 1077
<4>[ 2003.292114] EXT4-fs warning (device sda1): ext4_end_bio:258: I/O error writing to inode 13 (offset 217088 size 4096 starting block 1085)
<3>[ 2003.297576] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.297851] EXT4-fs error (device sda1): __ext4_get_inode_loc:4823: inode #13: block 5: comm libestool.so: unable to read itable block
<2>[ 2003.299560] EXT4-fs error (device sda1) in ext4_reserve_inode_write:5663: IO failure
<3>[ 2003.299743] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.300415] EXT4-fs error (device sda1): ext4_read_block_bitmap:353: comm libestool.so: Cannot read block bitmap - block_group = 0, block_bitmap = 3
<3>[ 2003.300720] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.301116] EXT4-fs error (device sda1): ext4_discard_preallocations:3828: comm libestool.so: Error reading block bitmap for 0
<3>[ 2003.301391] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.301727] EXT4-fs error (device sda1): ext4_read_block_bitmap:353: comm libestool.so: Cannot read block bitmap - block_group = 0, block_bitmap = 3
<3>[ 2003.302032] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.302398] EXT4-fs error (device sda1): ext4_discard_preallocations:3828: comm libestool.so: Error reading block bitmap for 0
<3>[ 2003.302703] EXT4-fs (sda1): previous I/O error to superblock detected
<3>[ 2003.303802] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.304168] EXT4-fs error (device sda1): ext4_free_branches:4377: inode #13: block 536: comm libestool.so: Read failure
<3>[ 2003.305358] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.305755] EXT4-fs error (device sda1): __ext4_get_inode_loc:4823: inode #13: block 5: comm libestool.so: unable to read itable block
<2>[ 2003.306365] EXT4-fs error (device sda1) in ext4_reserve_inode_write:5663: IO failure
<3>[ 2003.306518] EXT4-fs (sda1): previous I/O error to superblock detected
<3>[ 2003.336242] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.336364] EXT4-fs error (device sda1): ext4_find_entry:934: inode #2: comm libestool.so: reading directory lblock 0
<3>[ 2003.411834] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2003.412017] EXT4-fs error (device sda1): __ext4_get_inode_loc:4823: inode #2: block 5: comm ngs.android.pop: unable to read itable block
<2>[ 2003.412414] EXT4-fs error (device sda1) in ext4_reserve_inode_write:5663: IO failure
<3>[ 2003.412567] EXT4-fs (sda1): previous I/O error to superblock detected
<3>[ 2008.311859] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2008.312194] EXT4-fs error (device sda1): __ext4_get_inode_loc:4823: inode #13: block 5: comm bdi-default: unable to read itable block
<3>[ 2008.313110] EXT4-fs (sda1): previous I/O error to superblock detected
<2>[ 2008.313415] EXT4-fs error (device sda1): __ext4_get_inode_loc:4823: inode #2: block 5: comm bdi-default: unable to read itable block
<6>[ 2025.582702] fsa9480 4-0025: cable detect change, from 'unknown/none' to 'usb-host'
<6>[ 2026.233337] usb 1-1: new high speed USB device number 3 using musb-hdrc
<3>[ 2026.388244] usb 1-1: device v090c p6200 is not supported
<6>[ 2026.388427] usb 1-1: New USB device found, idVendor=090c, idProduct=6200
<6>[ 2026.388763] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 2026.389068] usb 1-1: Product: Generic USB2.0 card
<6>[ 2026.389221] usb 1-1: Manufacturer: Silicon Motion, Inc.
<6>[ 2026.389373] usb 1-1: SerialNumber: 12345678901234567890
<6>[ 2026.392089] scsi1 : usb-storage 1-1:1.0
<6>[ 2030.177124] fsa9480 4-0025: cable detect change, from 'usb-host' to 'unknown/none'
<4>[ 2030.180053] fsa9480 4-0025: irq fired, but nothing happened
<6>[ 2030.181335] fsa9480 4-0025: nothing attached, keeping ownership of port
<6>[ 2031.197509] max17040 4-0036: online = 1 vcell = 3600000 soc = 21 status = 2 health = 1 temp = 370 charger status = 0
<6>[ 2034.948303] fsa9480 4-0025: cable detect change, from 'unknown/none' to 'usb-host'
<6>[ 2035.182495] usb 1-1: USB disconnect, device number 3
<6>[ 2045.606109] fsa9480 4-0025: cable detect change, from 'usb-host' to 'unknown/none'
<4>[ 2045.609100] fsa9480 4-0025: irq fired, but nothing happened
<6>[ 2045.610321] fsa9480 4-0025: nothing attached, keeping ownership of port
<6>[ 2046.627288] max17040 4-0036: online = 1 vcell = 3602500 soc = 21 status = 2 health = 1 temp = 370 charger status = 0
<4>[ 2048.832824] ------------[ cut here ]------------
<4>[ 2048.832916] WARNING: at drivers/usb/musb/musb_host.c:125 musb_h_tx_flush_fifo+0x78/0x84()
<4>[ 2048.833068] Could not flush host TX2 fifo: csr: 2003
<4>[ 2048.833160] Modules linked in:
<4>[ 2048.833404] [<c0055de4>] (unwind_backtrace+0x0/0xf8) from [<c00983a8>] (warn_slowpath_common+0x4c/0x64)
<4>[ 2048.833526] [<c00983a8>] (warn_slowpath_common+0x4c/0x64) from [<c0098454>] (warn_slowpath_fmt+0x30/0x40)
<4>[ 2048.833679] [<c0098454>] (warn_slowpath_fmt+0x30/0x40) from [<c0366d70>] (musb_h_tx_flush_fifo+0x78/0x84)
<4>[ 2048.833862] [<c0366d70>] (musb_h_tx_flush_fifo+0x78/0x84) from [<c0367724>] (musb_cleanup_urb+0xb0/0xd4)
<4>[ 2048.834014] [<c0367724>] (musb_cleanup_urb+0xb0/0xd4) from [<c0367990>] (musb_urb_dequeue+0xfc/0x13c)
<4>[ 2048.834167] [<c0367990>] (musb_urb_dequeue+0xfc/0x13c) from [<c03441b0>] (usb_hcd_unlink_urb+0x60/0xac)
<4>[ 2048.834350] [<c03441b0>] (usb_hcd_unlink_urb+0x60/0xac) from [<c035d938>] (usb_stor_stop_transport+0x48/0x60)
<4>[ 2048.834442] [<c035d938>] (usb_stor_stop_transport+0x48/0x60) from [<c035c36c>] (command_abort+0x80/0x84)
<4>[ 2048.834564] [<c035c36c>] (command_abort+0x80/0x84) from [<c02d50ec>] (scsi_error_handler+0x3a4/0x49c)
<4>[ 2048.834716] [<c02d50ec>] (scsi_error_handler+0x3a4/0x49c) from [<c00b227c>] (kthread+0x80/0x88)
<4>[ 2048.834899] [<c00b227c>] (kthread+0x80/0x88) from [<c0050148>] (kernel_thread_exit+0x0/0x8)
<4>[ 2048.835052] Board Information: Tuna HW revision: 09 (Maguro 8th Sample), cpu OMAP4460 ES1.1
<4>[ 2048.835144] ---[ end trace 33de6ebe35ad56b7 ]---
<6>[ 2048.837768] scsi 1:0:0:0: Device offlined - not ready after error recovery
I found a thread on TI site for the OMAP4460 that discusses an error like mine but the signature is not the same, seems there they were having a problem with the the TCP/IP stack becoming corrupted because the processor was allocating memory too fast. Something like that is happening here. All I really know is it has to do with the handling of the L3 cache.

I think this may have to do with the cpu trying to idle when it should not.

What kind of drive are you using? If its a portable usb hard drive then this could be a power issue.

It's not a portable HD, just usb sd card reader.
With further investigation I have found that the problem might stem from the x-loader being mismatched to the kernel, which is part of the bootloader.

I tried different bootloaders, but none made a difference.
Finally, I tried a different USB OTG cable, a slightly more expensive one, and it worked.

[Q] sdcard suddenly stopped working

I have had my refurbished HTC Vision for about three weeks and it hadn't had any problems. Then yesterday, I rebooted it and now the sdcard doesn't work. Not just that it doesn't mount, rather there is not even a /dev/block/mmcblk1 device.
Here is what I tried:
* Boot into ClockworkMod, and run adb shell. Still no /dev/block/mmcblk1.
* Boot into fastboot and run "fastboot oem enableqxdm 0" and "fastboot oem eraseconfig".
* Per some random instructions on the net, I held vol-up and power, then pulled the battery after the phone vibrated. Then I held vol-up, vol-down, power and did the same. Then the fastboot commands again.
* Bent the sdcard port's pins out a bit with tweezers.
* SDcard works in computer (Linux).
* Tried another card that has nothing but a vfat partition.
Nothing works! There are some errors in dmesg:
Code:
$ dmesg |grep mmc
<5>[ 0.000000] Kernel command line: board_vision.disable_uart2=0 board_vision.usb_h2w_sw=0 board_vision.disable_sdcard=0 diag.enabled=0 board_vision.debug_uart=0 smisize=0 userdata_sel=0 androidboot.emmc=true androidboot.baseband=26.02.01.15_M2 androidboot.cid=T-MOB010 androidboot.batt_poweron=good_battery androidboot.carrier=TMUS androidboot.mid=PC1010000 androidboot.keycaps=qwerty androidboot.mode=normal androidboot.serialno=HT09LR200858 androidboot.bootloader=0.76.2000 no_console_suspend=1 console=null
<6>[ 2.532989] vision: vision_init_mmc
<3>[ 3.267822] mmc0: No card detect facilities available
<6>[ 3.268341] mmc0: Qualcomm MSM SDCC at 0x00000000a0500000 irq 98,0 dma 7
<6>[ 3.268615] mmc0: Platform slot type: MMC
<6>[ 3.268737] mmc0: 4 bit data mode disabled
<6>[ 3.269012] mmc0: 8 bit data mode enabled
<6>[ 3.269134] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.269378] mmc0: Slot eject status = 0
<6>[ 3.269531] mmc0: Power save feature enable = 1
<6>[ 3.269653] mmc0: DM non-cached buffer at ffa0c000, dma_addr 0x2b774000
<6>[ 3.269927] mmc0: DM cmd busaddr 0x2b774000, cmdptr busaddr 0x2b774300
<6>[ 3.270751] mmc1: Qualcomm MSM SDCC at 0x00000000a3000000 irq 96,0 dma 8
<6>[ 3.270996] mmc1: Platform slot type: N/A
<6>[ 3.271148] mmc1: 4 bit data mode enabled
<6>[ 3.271392] mmc1: 8 bit data mode disabled
<6>[ 3.271514] mmc1: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.271789] mmc1: Slot eject status = 1
<6>[ 3.271911] mmc1: Power save feature enable = 1
<6>[ 3.272064] mmc1: DM non-cached buffer at ffa0d000, dma_addr 0x2b777000
<6>[ 3.272308] mmc1: DM cmd busaddr 0x2b777000, cmdptr busaddr 0x2b777300
<6>[ 3.273468] mmc2: Qualcomm MSM SDCC at 0x00000000a3100000 irq 100,0 dma 8
<6>[ 3.273712] mmc2: Platform slot type: SD
<6>[ 3.273834] mmc2: 4 bit data mode enabled
<6>[ 3.273986] mmc2: 8 bit data mode disabled
<6>[ 3.274230] mmc2: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.274353] mmc2: Slot eject status = 0
<6>[ 3.274658] mmc2: Power save feature enable = 1
<6>[ 3.274810] mmc2: DM non-cached buffer at ffa0e000, dma_addr 0x2b778000
<6>[ 3.275054] mmc2: DM cmd busaddr 0x2b778000, cmdptr busaddr 0x2b778300
<6>[ 3.275207] mmc2: Polling status mode enabled
<6>[ 3.425598] mmc0: new high speed MMC card at address 0001
<6>[ 3.427093] mmcblk0: mmc0:0001 SEM04G 2.09 GiB
<6>[ 3.428100] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 >
<6>[ 3.569030] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts: barrier=1
<4>[ 3.703063] mmc2: high speed mode max_dtr = 50000000
<4>[ 3.703491] mmc2: host does not support reading read-only switch. assuming write-enable.
<6>[ 3.703643] mmc2: new high speed SDHC card at address 0001
<6>[ 3.704498] mmcblk1: mmc2:0001 00000 7.41 GiB
<6>[ 3.705291] mmcblk1: p1
<4>[ 4.648254] EXT4-fs (mmcblk0p26): warning: maximal mount count reached, running e2fsck is recommended
<7>[ 4.651062] EXT4-fs (mmcblk0p26): ext4_orphan_cleanup: deleting unreferenced inode 24790
<7>[ 4.655670] EXT4-fs (mmcblk0p26): ext4_orphan_cleanup: deleting unreferenced inode 24741
<6>[ 4.657012] EXT4-fs (mmcblk0p26): 2 orphan inodes deleted
<6>[ 4.657379] EXT4-fs (mmcblk0p26): recovery complete
<6>[ 4.703216] EXT4-fs (mmcblk0p26): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<4>[ 4.758331] EXT4-fs (mmcblk0p27): warning: maximal mount count reached, running e2fsck is recommended
<6>[ 4.760345] EXT4-fs (mmcblk0p27): recovery complete
<6>[ 4.762298] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: barrier=1
<4>[ 4.886474] EXT4-fs (mmcblk0p28): warning: maximal mount count reached, running e2fsck is recommended
<6>[ 4.888580] EXT4-fs (mmcblk0p28): recovery complete
<6>[ 4.890563] EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: barrier=1
<7>[ 20.824981] mmc1: card_present 1
<6>[ 20.825134] mmc1: Slot status change detected (0 -> 1)
<7>[ 23.383300] mmc1: queuing CIS tuple 0x91 length 3
<6>[ 23.383331] mmc1: new high speed SDIO card at address 0001
<3>[ 38.746368] mmc2: Data CRC error
<6>[ 38.746978] mmc2: Controller has been reset
<3>[ 38.747467] mmcblk1: error -84 transferring data, sector 2080, nr 1, card status 0x900
<6>[ 38.747619] mmc2: reinit card
<4>[ 38.747863] mmc2: Starting deferred resume
<3>[ 38.814849] mmc2: Data CRC error
<6>[ 38.815521] mmc2: Controller has been reset
<3>[ 38.815856] mmc2: Re-init card rc = -84 (retries = 5)
<3>[ 38.997650] mmc2: Data CRC error
<6>[ 38.998291] mmc2: Controller has been reset
<3>[ 39.001403] mmc2: Re-init card rc = -84 (retries = 4)
<3>[ 39.200927] mmc2: Data CRC error
<6>[ 39.201507] mmc2: Controller has been reset
<3>[ 39.201721] mmc2: Re-init card rc = -84 (retries = 3)
<3>[ 39.384826] mmc2: Data CRC error
<6>[ 39.385406] mmc2: Controller has been reset
<3>[ 39.385650] mmc2: Re-init card rc = -84 (retries = 2)
<3>[ 39.583618] mmc2: Data CRC error
<6>[ 39.584228] mmc2: Controller has been reset
<3>[ 39.584472] mmc2: Re-init card rc = -84 (retries = 1)
<6>[ 39.666137] mmc2: Deferred resume failed
<6>[ 39.666412] mmc: reinit failed, remove card
<6>[ 39.666625] mmc2: remove card
<3>[ 39.666778] end_request: I/O error, dev mmcblk1, sector 2080
<3>[ 39.667053] Buffer I/O error on device mmcblk1p1, logical block 32
<4>[ 39.667205] lost page write due to I/O error on mmcblk1p1
<3>[ 39.667480] mmc_blk_issue_rq failed!!
<6>[ 39.667633] mmc2: mmc_remove_sd_card
<6>[ 39.667907] mmc2: card 0001 removed
<3>[ 39.670318] mmcblk1: error -123 sending status comand
<3>[ 39.670471] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.670867] end_request: I/O error, dev mmcblk1, sector 2080
<3>[ 39.671783] mmc_blk_issue_rq failed!!
<3>[ 39.671966] mmcblk1: error -123 sending read command, response 0x0
<4>[ 39.672210] mmcblk1: retrying using single block read
<3>[ 39.672332] mmcblk1: error -123 sending status comand
<3>[ 39.672607] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.672882] end_request: I/O error, dev mmcblk1, sector 32378
<3>[ 39.673126] end_request: I/O error, dev mmcblk1, sector 32379
<3>[ 39.673278] end_request: I/O error, dev mmcblk1, sector 32380
<3>[ 39.673522] end_request: I/O error, dev mmcblk1, sector 32381
<3>[ 39.673675] end_request: I/O error, dev mmcblk1, sector 32382
<3>[ 39.673919] end_request: I/O error, dev mmcblk1, sector 32383
<3>[ 39.674072] end_request: I/O error, dev mmcblk1, sector 32384
<3>[ 39.674316] end_request: I/O error, dev mmcblk1, sector 32385
<3>[ 39.674499] mmc_blk_issue_rq failed!!
<3>[ 39.674774] mmcblk1: error -123 sending status comand
<3>[ 39.674926] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.675292] end_request: I/O error, dev mmcblk1, sector 32378
... and so on. In this run, I see that at least briefly the kernel could read the mmcblk1 partition table (although there still was not /dev/block/mmcblk1). However, most of the time it can't and just gives the CRC errors.
Is this a hardware or software problem. Any suggestions? Thanks.

Almost 100% hardware from what you have written, I would suggest disconnecting the ribbion cable, clean it, and put it back. If it still won't work a new sd card tray is about 10$ on ebay and a snap to put it
Sent from my HTC Vision using xda premium

worked!
demkantor said:
Almost 100% hardware from what you have written, I would suggest disconnecting the ribbion cable, clean it, and put it back. If it still won't work a new sd card tray is about 10$ on ebay and a snap to put it
Sent from my HTC Vision using xda premium
Click to expand...
Click to collapse
Worked, thanks!!! The CRC errors made me suspect hardware, but I wanted someone else to say it before I tore the thing open. I've always had bad luck tearing these things apart (only junk phones in the past), but I bought a cheapo disassembly kit a while back which has helped greatly with popping the case off. And thankfully I only had to get to about step three of the instructions before the ribbon cable was accessible!

Random reboot: need your expert help!

Hi all, I have a Note 2 that randomly rebooted when I was charging it. It didn't always do it, but occasionally. This time, after it rebooted when connected to a wall charger (it was already fully charged as the green LED was on for several hours), I disconnected the charging cable and connected it to my computer to do a dump:
adb shell cat /proc/last_kmesg > last_kmesg_11212013.txt
Here is the link of this log file:
https://www.dropbox.com/s/6b4f6ygrtg4b4uk/last_kmsg_11212013.txt
and here is the section that was related to the reboot from the attached log file. There was a panic and the system rebooted. I'm not familiar with Android internal. I hope someone could help me to identify why that happened?
** The phone was in airplane mode (no wifi/data/voice/GPS) when the reboot happened. It's rooted and running stock JB 4.1.2. My phone has the sane emmc chip.
** Noticed that it kept powering on 'mdm' every 5 seconds. The phone was in airplane mode, why Android kept powering on the modem? It was during one of these 'powering on mdm' that it failed and rebooted.
I'd appreciate all the help I can get. Thank you.
<6>[ 3178.869129] c0 mdm_subsys_powerup: mdm modem restart timed out.
<0>[ 3178.869289] c0 Kernel panic - not syncing: subsystem_restart_wq_func[e85f0cc0]: Failed to powerup external_modem!
<4>[ 3178.869498] c0 Backtrace:
<4>[ 3178.869666] c0 [<c0061cd0>] (dump_backtrace+0x0/0x114) from [<c06495cc>] (dump_stack+0x20/0x24)
<4>[ 3178.869851] c0 r7:e563c540 r6:c0abfc34 r5:c0ac6ff0 r4:c0b6f5a0
<4>[ 3178.870056] c0 [<c06495ac>] (dump_stack+0x0/0x24) from [<c0649654>] (panic+0x84/0x1b8)
<4>[ 3178.870269] c0 [<c06495d0>] (panic+0x0/0x1b8) from [<c00802c0>] (subsystem_restart_wq_func+0x21c/0x258)
<4>[ 3178.870464] c0 r3:c0919200 r2:e85f0cc0 r1:c0650f7c r0:c0919b00
<4>[ 3178.870678] c0 [<c00800a4>] (subsystem_restart_wq_func+0x0/0x258) from [<c00bbc18>] (process_one_work+0x14c/0x4a0)
<4>[ 3178.870923] c0 [<c00bbacc>] (process_one_work+0x0/0x4a0) from [<c00bc304>] (worker_thread+0x18c/0x3e8)
<4>[ 3178.871149] c0 [<c00bc178>] (worker_thread+0x0/0x3e8) from [<c00c2edc>] (kthread+0x98/0xa0)
<4>[ 3178.871367] c0 [<c00c2e44>] (kthread+0x0/0xa0) from [<c00a5da4>] (do_exit+0x0/0x754)
<4>[ 3178.871532] c0 r7:00000013 r6:c00a5da4 r5:c00c2e44 r4:dba8feb0
<6>[ 3178.972415] c0 notifier_call_chain : NOTIFY BAD sec_debug_panic_handler
<0>[ 3178.972575] c0 Rebooting in 1 seconds..
<7>[ 3179.754044] c0 s5p-ohci s5p-ohci: auto-stop root hub
<0>[ 3179.976977] c0 sec_reboot (104, emergency)

Nobody saw this before?
The reboot never happened when the phone was off the charger.