Related
Has anyone found a MHL cable that also includes a USB OTG port? Samsung reportedly changed from a 5-pin configuration to an 11-pin configuration to allow MHL with USB Host mode simultaneously. Perhaps for a future Desktop Mode?
Has anyone been able to find one of these cables?
Just wanted to update, I believe I found the type of connector that I was looking for, but it is missing HDMI and it is sold out. This essentially could give you PC type connectivity on the S3.
http://www.mobilefun.com/35462-mobile-fun-connection-kit-for-samsung-galaxy-s3.htm
I think we still have a bit of a wait. What you found is essentially a USB OTG hub with some card readers built in. I seriously doubt this will pass through the pins for HDMI to work out of the usb port. We'll see something when this phone finally launches everywhere. It's not even out in the US officially yet
EDIT: Sorry, didn't see the article in the link in the OP. Man.. I might have to get me a GS3 now. I'm quite satisfied with the reasoning for a pin change. =)
Samsung sells 11 pin MHL adapters and USB female to Micro USB male adapters on their accessories page, but I'm not sure if you could piggy back the USB input into the charging port of the MHL cable. I don't see any all in one cables on their site, and the desktop dock is just micro usb/audio. I tried.. =(
Here's what I was looking at.
Old and mostly unrelated. See edit.
I happened to buy what looks exactly like that adapter today earlier at Micro Center. Now, I do have a Galaxy Nexus, but the USB OTG works great with keyboards/usb/mice/hubs; however, I cannot get it to simultaneously work with my MHL adapter. I understand the GS3 has a different pin layout though for MHL - my phone works with my MHL adapter correctly, but I didn't think it would have any change on the USB OTG. I'll most likely be breaking these apart and start tinkering. My goal is to show people how much of a full desktop-like experience I can provide from my phone, since so many people somehow think a GNex or GS3 are inferior to tablets, just because they're smaller... lol
Good luck finding information out on some kind of MHL/USB OTG setup. I'm just trying to provide any information I can from how my situation works with MHL/OTG, since I'm currently on the quest to achieve this myself.
kynolin said:
EDIT: Sorry, didn't see the article in the link in the OP. Man.. I might have to get me a GS3 now. I'm quite satisfied with the reasoning for a pin change. =)
Samsung sells 11 pin MHL adapters and USB female to Micro USB male adapters on their accessories page, but I'm not sure if you could piggy back the USB input into the charging port of the MHL cable. I don't see any all in one cables on their site, and the desktop dock is just micro usb/audio. I tried.. =(
Here's what I was looking at.
Old and mostly unrelated. See edit.
I happened to buy what looks exactly like that adapter today earlier at Micro Center. Now, I do have a Galaxy Nexus, but the USB OTG works great with keyboards/usb/mice/hubs; however, I cannot get it to simultaneously work with my MHL adapter. I understand the GS3 has a different pin layout though for MHL - my phone works with my MHL adapter correctly, but I didn't think it would have any change on the USB OTG. I'll most likely be breaking these apart and start tinkering. My goal is to show people how much of a full desktop-like experience I can provide from my phone, since so many people somehow think a GNex or GS3 are inferior to tablets, just because they're smaller... lol
Good luck finding information out on some kind of MHL/USB OTG setup. I'm just trying to provide any information I can from how my situation works with MHL/OTG, since I'm currently on the quest to achieve this myself.
Click to expand...
Click to collapse
I'm not really sure why people think they NEED MHL and USB OTG simultaneously to get a "desktop-like experience". You can already accomplish this with just a plain MHL cable and a bluetooth keyboard and mouse as was demonstrated in the Connectivity Demo video on youtube.
Edit: Actually I just remembered about portable hard drives. If you want to hook up a mouse, keyboard AND hard drive I wonder if you can plug all three into a powered USB hub connected to a bluetooth dongle. Hmm...
I'm looking for a dock with USB OTG, charging and MHL. Maybe some day.
I believe this is already capable. Everything I say here is purely speculative, but what I see is that Samsung moved to a 11-pin connector for MHL and the standard 5-pin is no longer functioning. To call it MHL, they probably have to use the same standards for data encoding... but they simply "moved" the pins.
I put "moved" in quotes because of the way in which a standard 4 pin USB cable works (or 5 pin for our case)... you have a +5V, Ground, Data + and Data - (one data to phone, one data from phone, carrying ALL data). Since our phones still sync via 5-pin cables, this means the 5 pins are still "hot" for data like all other phones. I am presuming, that for the 11-pin connector, Samsung simply added a few more data+ and data- connectors (much like having two or three USB ports on a normal computer) but consolidated the ground/5V reference. I could be wrong, but it would make sense.
Lets call the stock 5 pin data connectors (2 wires) USB1. This is where MHL is conventionally sent through and all sycing can be completed through, 5 pin cable or 11 pin cable. If samsung added two additional USB ports to the single connector, lets say MHL is now over USB2 (wires inaccessible to 5 pin connectors). This frees up bandwidth and COM ports on USB1 and USB3 to use for accessories like a USB hard drive and keyboard/mouse. On a 5 pin connector, however, only USB1 is accessible. The Samsung 11pin to 5pin MHL adapter simply moves the data+/- from USB2 to USB1 (standard 5 pin location), so with the adapter you are syncing/exporting video over USB2 on the phone with a standard 5pin cable.
My thinking is such: If you plug in the OEM 11pin MHL adapter, it will also have access to the standard 5pin USB1 connection. Since USB2 is used for MHL, you can then plug any OTG device into the micro USB connector on the MHL adapter to make use of it. The only problem here is power (or lack thereof). By plugging in a USB hub with a discrete power source, plugging this into the MHL adapter, and plugging in the USB device of choice into the HUB, you *SHOULD* be able to get simultaneous data and HDMI. This assumes they put the standard 5 pins to the connector on the side of the MHL adapter and only wired the HDMI to the USB2 area.
Alternatively, you *SHOULD* be able to plug the micro USB cable from the MHL adapter into a computer, and simultaneously be able to sync files while outputting HDMI video. It sort of just comes down to being able to provide power to the MHL adapter on the +5V pin while using the data pins to access the phone. As soon as I have my MHL I'll figure it out, but that could be a bit. If anybody has access to a pinout from a Samsung 11 pin micro USB that would be helpful too.
Again, just dreaming here. I don't know anything about this, but if I was the engineer at Samsung I would choose this over analog outputs like Apple used for their giant connector.
kthung said:
I'm not really sure why people think they NEED MHL and USB OTG simultaneously to get a "desktop-like experience". You can already accomplish this with just a plain MHL cable and a bluetooth keyboard and mouse as was demonstrated in the Connectivity Demo video on youtube.
Edit: Actually I just remembered about portable hard drives. If you want to hook up a mouse, keyboard AND hard drive I wonder if you can plug all three into a powered USB hub connected to a bluetooth dongle. Hmm...
Click to expand...
Click to collapse
for me at least i already have several keyboards and mice ... none are bluetooth.
I'm looking for the cheapest option available.
I'm just hoping someone releases a cable with 4 plugs:
Male MHL - To Phone Obviously
Female MicroUSB: To plug in charger
Female HDMI - To Display
Female USB - To USB Device
That's all I want... should cost less than $2 to make, just sell it for $20 and I'd be happy.
v8bait said:
I believe this is already capable. Everything I say here is purely speculative, but what I see is that Samsung moved to a 11-pin connector for MHL and the standard 5-pin is no longer functioning. To call it MHL, they probably have to use the same standards for data encoding... but they simply "moved" the pins.
I put "moved" in quotes because of the way in which a standard 4 pin USB cable works (or 5 pin for our case)... you have a +5V, Ground, Data + and Data - (one data to phone, one data from phone, carrying ALL data). Since our phones still sync via 5-pin cables, this means the 5 pins are still "hot" for data like all other phones. I am presuming, that for the 11-pin connector, Samsung simply added a few more data+ and data- connectors (much like having two or three USB ports on a normal computer) but consolidated the ground/5V reference. I could be wrong, but it would make sense.
Lets call the stock 5 pin data connectors (2 wires) USB1. This is where MHL is conventionally sent through and all sycing can be completed through, 5 pin cable or 11 pin cable. If samsung added two additional USB ports to the single connector, lets say MHL is now over USB2 (wires inaccessible to 5 pin connectors). This frees up bandwidth and COM ports on USB1 and USB3 to use for accessories like a USB hard drive and keyboard/mouse. On a 5 pin connector, however, only USB1 is accessible. The Samsung 11pin to 5pin MHL adapter simply moves the data+/- from USB2 to USB1 (standard 5 pin location), so with the adapter you are syncing/exporting video over USB2 on the phone with a standard 5pin cable.
My thinking is such: If you plug in the OEM 11pin MHL adapter, it will also have access to the standard 5pin USB1 connection. Since USB2 is used for MHL, you can then plug any OTG device into the micro USB connector on the MHL adapter to make use of it. The only problem here is power (or lack thereof). By plugging in a USB hub with a discrete power source, plugging this into the MHL adapter, and plugging in the USB device of choice into the HUB, you *SHOULD* be able to get simultaneous data and HDMI. This assumes they put the standard 5 pins to the connector on the side of the MHL adapter and only wired the HDMI to the USB2 area.
Alternatively, you *SHOULD* be able to plug the micro USB cable from the MHL adapter into a computer, and simultaneously be able to sync files while outputting HDMI video. It sort of just comes down to being able to provide power to the MHL adapter on the +5V pin while using the data pins to access the phone. As soon as I have my MHL I'll figure it out, but that could be a bit. If anybody has access to a pinout from a Samsung 11 pin micro USB that would be helpful too.
Again, just dreaming here. I don't know anything about this, but if I was the engineer at Samsung I would choose this over analog outputs like Apple used for their giant connector.
Click to expand...
Click to collapse
hi v8bait, are you able to get data thru the micro usb port at the side of the 11-pin mhl adapter? i was thinking of using the motorola lapdock with my s3 thru the mhl adaptor (other then a micro hdmi male connector, the lapdock also has a micro usb male connector that apparently send out power as well as push keyboard/trackpad data upstream) - if it works, we can have an inexpensive "clambook"
Just to recap,
Will this we possible:
Official MHL adapter -> hdmi to monitor.
|
>OTG cable> Powered USB hub> USB keyboard & mouse.
In other words, the PC Experience with a keyboard and mouse.
Dont really want to spend the money to buy a Bluetooth keyboard and mouse when the USB ones can work just fine (theoretically).
romulusram said:
Just to recap,
Will this we possible:
Official MHL adapter -> hdmi to monitor.
|
>OTG cable> Powered USB hub> USB keyboard & mouse.
In other words, the PC Experience with a keyboard and mouse.
Dont really want to spend the money to buy a Bluetooth keyboard and mouse when the USB ones can work just fine (theoretically).
Click to expand...
Click to collapse
I am also very interested in this exact thing. Using USB devices (multiple ones, e.g. plugging a powered USB hub into S III and then plugging them in) but also putting out S III video to HDMI.
However the other workaround is using AllShare Cast. In fact that is the route I'll likely go, because of the other unique advantages of AllShare Cast (i.e. using it for presentations to screens, etc.)
So: has anyone plugged a powered USB hub into S III and used multiple devices? Such as a keyboard and mouse?
I also want to use this S III more as a computer. the other perfect thing I wish I could buy would be a keyboard case, like the one available for iphone, so I can prop the S III up on a kickstand and use a real mini-QWERTY physical keyboard.
macdroid01 said:
I am also very interested in this exact thing. Using USB devices (multiple ones, e.g. plugging a powered USB hub into S III and then plugging them in) but also putting out S III video to HDMI.
However the other workaround is using AllShare Cast. In fact that is the route I'll likely go, because of the other unique advantages of AllShare Cast (i.e. using it for presentations to screens, etc.)
So: has anyone plugged a powered USB hub into S III and used multiple devices? Such as a keyboard and mouse?
I also want to use this S III more as a computer. the other perfect thing I wish I could buy would be a keyboard case, like the one available for iphone, so I can prop the S III up on a kickstand and use a real mini-QWERTY physical keyboard.
Click to expand...
Click to collapse
We're in the same boat; i want to use the s3 like a mini computer too. I think it'd be great for business travel, when i dont really need a laptop during the day but want something when i'm back in hotel room. I'd much rather use hotel TV instead of a laptop because that's what i am used to at home... pc hooked to TV.
I've been planning to use the allshare cast dongle too, but they dont seem to be available yet. I was thinking HDMI out with the allshare.. charging with the wireless charging kit and then keyboard and mouse with USB OTG. My logitech unifying receiver for keyboard/mouse works perfectly i just need the wireless charging and allshare dongle to be released.
For what it's worth I tried a powered USB hub and could not get it to work with the s3.
faulkton said:
For what it's worth I tried a powered USB hub and could not get it to work with the s3.
Click to expand...
Click to collapse
Wait so your saying you tried a (a) powered USB hub with a OTG cable connected to the phone or you tried a (b) powered USB hub connected with a OTG cable to the MHL adapter and then to the phone?
If it was (a) then there are some vids out there of ppl using powered USB hubs.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
So has anyone received their Official MHL adapater and tried USB OTG?
Very interested in this.,,
I'm puzzled that there aren't any more postings about this kind of stuff. I was expecting the GS3 to be easy to use as a "PC" replacement but it seems no one besides us few wanted to do that ? A simple cable should have done it but I'd even be willing to shell out 40-50$ for a decent dock that would do just that
romulusram said:
So has anyone received their Official MHL adapater and tried USB OTG?
Very interested in this.,,
Click to expand...
Click to collapse
Me too.
But it is possible to get that this way working:
Code:
S3 -> Mobile Fun Connection Kit -> microusb -> HDTV Adapter TIP (5 to 11 Pin Converter) -> MHL HDMI adapter
|
-> USB -> keyboard etc.
Links
http://www.mobilefun.com/35462-mobile-fun-connection-kit-for-samsung-galaxy-s3.htm
http://www.samsung.com/us/mobile/cell-phones-accessories/EPL-FU10BEGSTA
Maybe I'm not reading these posts correctly but I am using an usb keyboard and a usb mouse on my S3 with no problems using these two accessories:
http://www.amazon.com/Belkin-USB-2-...e=UTF8&qid=1343845994&sr=8-1&keywords=usb+hub
http://www.amazon.com/Micro-USB-OTG...UTF8&qid=1343846045&sr=1-3&keywords=otg+cable
Have my keyboard and mouse plugged into the usb hub and then the usb hub into my usb OTG cable which of course plugs into the S3. Everything's working on my end.
romulusram said:
So has anyone received their Official MHL adapater and tried USB OTG?
Very interested in this.,,
Click to expand...
Click to collapse
I have the official MHL adapter and there is no female USB port on it for OTG
badbeat33 said:
Maybe I'm not reading these posts correctly but I am using an usb keyboard and a usb mouse on my S3 with no problems using these two accessories:
http://www.amazon.com/Belkin-USB-2-...e=UTF8&qid=1343845994&sr=8-1&keywords=usb+hub
http://www.amazon.com/Micro-USB-OTG...UTF8&qid=1343846045&sr=1-3&keywords=otg+cable
Have my keyboard and mouse plugged into the usb hub and then the usb hub into my usb OTG cable which of course plugs into the S3. Everything's working on my end.
Click to expand...
Click to collapse
You are not reading it right.
they want to use the MHL adapter, too.
As far as i can tell, the MHL adapter needs to be in the phone, not a hub. it is all dictated (the output being OTG, or MHL) by the impedance of what is plugged in. It is an either or situation.
Perhaps with a firmware update they MIGHT be able to run both signals and split it.. but i doubt it.
This thread intended to be an easy location to add tried adapters and accessories connecting to the USB-C port.
Sent from my HTC 10 using XDA-Developers mobile app
HDMI port.
Adapter must use display port protocol (I think). This USB-C to HDMI, USB3.1, and USB-C (charging port in only) works. Found on eBay.
USB Type C Hub for Macbook Pixel USB C to HDMI USB 3.0 & USB-C Charging Port
Brand MyTripleBest
MTB--USB-C-A.
This one uses MHL protocol, and does NOT work.
Black Type-C MHL 2.0 to HDMI Female HDTV Monitor Adapter USB 3.1 Cable Converter
Sent from my HTC 10 using XDA-Developers mobile app
Micro USB accessories.-
For OTG accessories, and some attachments such as cameras, the phone is the USB host.
'Conforming' USB-C to micro adapters (listing the '56k resistor' ) will not work. Tells the phone to take a charge, it is not host.
Look for adapters that are non conforming, better yet are 'OTG' compatible.
One is:
Meenova
USB 3.1 Type-C to MicroUSB 2.0 Female OTG Adapter, Gray, pack of 2
My micro USB thermal camera, 3d camera, and USB host cables work. There are other brands as well.
## This message is NOT about connecting phone to a charger or PC ##
Sent from my HTC 10 using XDA-Developers mobile app
lsblack said:
Micro USB accessories.-
For OTG accessories, and some attachments such as cameras, the phone is the USB host.
'Conforming' USB-C to micro adapters (listing the '56k resistor' ) will not work. Tells the phone to take a charge, it is not host.
Look for adapters that are non conforming, better yet are 'OTG' compatible.
One is:
Meenova
USB 3.1 Type-C to MicroUSB 2.0 Female OTG Adapter, Gray, pack of 2
My micro USB thermal camera, 3d camera, and USB host cables work. There are other brands as well.
## This message is NOT about connecting phone to a charger or PC ##
I'm currently (partially successfully) using the following in an attempt to use an External 1TB Drive as a portable backup solution for travels:
Type C Adapter, RAVPower USB C To A Female OTG Cable, USB-C On The Go Convertor for New MacBook and Other Devices with Type C USB
I can get images onto the phone's internal 128GB card (Lexar Professional 1800x microSDXC 128GB UHS-II W/USB 3.0 Reader Flash Memory Card - LSDMI128CRBNA1800R) via OTG and Card Reader ...I cannot get them off of the internal on to the External 1TB via the OTG cable.
Click to expand...
Click to collapse
Problem with old HTC M8 Charger
At home I use the charger that came with the phone.
At the office, I was planning to use the HTC charger that came with my old M8, maybe not quite as fast.
But strangely enough, when I do that, the charge light turns on and off every couple of seconds, it wakes the phone, and it doesn't charge.
A Belkin 2.1A charger I had works fine though. Go figure.
I don't think the HTC 10 is compliant with USB-C Power Delivery (Such as the Nexus 6p) do deliver the rapid charging speeds of up to 3A via a USB-C charger and a USB-C to USB-C cable. I remember reading up about it of an article referencing Benson Leung (not the 1st one, but most recent one). He said the LG G5 is compliant with the Power Delivery achieving the 3A max input. But the HTC 10 only achieves 2A.
I can about confirm this because I have 2 USB-C wall chargers, one by Cheotech that gives me around 1600mah-1700mAh, and one by iClever, which gives me the same speeds. My RavPower Turbo Series Powerbank with the USB-C port and the max of 3A output gives me the same 1600-1700mAh speeds of input into the HTC 10 as well.
I've tested a Samsung adaptive fast charger from the s7 and s6 with the OEM cable and a ravpower A to C cable and it shows Rapid Charging when plugged in.
Sent from my HTC 10 using XDA-Developers mobile app
MTB Adapter
@lsblack
adapter must use display port protocol (I think). This USB-C to HDMI, USB3.1, and USB-C (charging port in only) works. Found on eBay.
USB Type C Hub for Macbook Pixel USB C to HDMI USB 3.0 & USB-C Charging Port
Brand MyTripleBest
MTB--USB-C-A.
This adapter didnt worked with my HTC 10, it showed that video was conected but there was no transmition over to the TV or monitor, or am i doing something wrong? i mean i tried everything, and it didnt worked >.<, or maybe i got a defective unit? also, are you connecting into a 1080p, 2k or 4k TV/Monitor? maybe is that...
Has anyone gotten one to work I bought 2 from Amazon and none seem to work. Maybe I thought wrong but thought HTC 10 has displayport output.
Sent from my HTC 10 using Tapatalk
I tried one at work last week, worked fine. Not sure what kind i got, but was not a problem.
OK thanks... I'll probably go to Best Buy and see if I can test one out there. Hope I don't have a bad port
Sent from my HTC 10 using Tapatalk
[Cruzer] said:
OK thanks... I'll probably go to Best Buy and see if I can test one out there. Hope I don't have a bad port
Click to expand...
Click to collapse
I've tried 2. One worked, one didn't. Both were designed for macbooks, so ymmv.
I will try this out when I get the chance.
Tried one at the Computex last WE, for MacBook. Didn't work.
And after I tried the HTC10 and put it back to the MacBook it didn't work at all anymore.
Haldi4803 said:
Tried one at the Computex last WE, for MacBook. Didn't work.
And after I tried the HTC10 and put it back to the MacBook it didn't work at all anymore.
Click to expand...
Click to collapse
damn thats not good news. still haven't had the time to head to local bestbuy. Hoping someone got one to work and point to an amazon link really miss having to show movies (for my kids) on the screen. Still have my MHL adpater for htc m9.
Adapter needs to use display port protocol, not mhl. Some adapters (USBC to HDMI) will use mhl internally and won't work (to my knowledge). See USB-C thread in 'Real Life'? section.
Sent from my HTC 10 using XDA-Developers mobile app
lsblack said:
Adapter needs to use display port protocol, not mhl. Some adapters (USBC to HDMI) will use mhl internally and won't work (to my knowledge). See USB-C thread in 'Real Life'? section.
Sent from my HTC 10 using XDA-Developers mobile app
Click to expand...
Click to collapse
Yes I know can't use MHL for HTC 10.. Just saying I miss that feature. And almost nagging at me still is the MHL cable. starring at me saying why did you get of the M9 [emoji14] you could be watching videos on the 70inch right now.
Sent from my HTC 10 using Tapatalk
Buy your nagging mhl cable a baby sister; a USB-C to HDMI port adapter / hub. It uses display port protocol and supports 4k. Adapter also includes USB 3.0 host port (so OTG) and 2nd USB-C port (for charger connection, I think optional, but I always use). Charge phone and watch at same time. See referenced thread for source. Win-win but approx $30. Need standard HDMI cable. Works well for me.
Sent from my HTC 10 using XDA-Developers mobile app
I ran into the same problem the mac pro adapter, it would charge or display not both. I went this route Microsoft - Wireless Display Adapter V2 receiver - Dark-Titanium and use HTC connect. It works great.
lsblack said:
Buy your nagging mhl cable a baby sister; a USB-C to HDMI port adapter / hub. It uses display port protocol and supports 4k. Adapter also includes USB 3.0 host port (so OTG) and 2nd USB-C port (for charger connection, I think optional, but I always use). Charge phone and watch at same time. See referenced thread for source. Win-win but approx $30. Need standard HDMI cable. Works well for me.
Click to expand...
Click to collapse
Just curious... you've had no problem charging this way? I wasn't sure if the 10 could take a regular USB-C charger or if it needed a QC compatible charger.
Partial answer. The HTC-10 does not need QC2 charger, just might charge slower or at various rates supplied by charger. I use several different chargers I had for my micro USB phones. Both using micro-USBC adapters, and USB-C cable direct. What I haven't tried (per your question), is fully charging via the mentioned display adapter. I doubt that the will recognize it as QC2. I will try this with the HTC supplied charger.
Sent from my HTC 10 using XDA-Developers mobile app
Here a very quick video of my HTC 10 working on HDMI while being charged.
Hi
Here a very quick video of my HTC 10 working on HDMI while being charged.
5Gbps UBS 3.1 TypeC to 4K HDMI USB 3.0 HUB USBC Charging Port OTG Adapter UK 5Gbps UBS 3.1 Type-C to 4K HDMI USB 3.0 HUB USB-C Charging Port OTG Adapter UK | eBay
No Audio out via HDMI on this product. There is audio just does not work on my monitor via HDMI but works fine on TVs.
Video Output was 1080p @60fps
Sorry for the bad video; as it was taken with my Nexus 7.
https://youtu.be/Iuf1YoBzzn8
Thanks for this, will be ordering one myself now.
edit: no audio out on this device, well then that sucks. Not good for watching video, yah I know I probably can use headphone jack for that but should work that way in my opinion. guess I'll still be on the hunt for a simple HDMI and audio output like the good old MHL adapter.
1stGGMan said:
Hi
Here a very quick video of my HTC 10 working on HDMI while being charged.
5Gbps UBS 3.1 TypeC to 4K HDMI USB 3.0 HUB USBC Charging Port OTG Adapter UK 5Gbps UBS 3.1 Type-C to 4K HDMI USB 3.0 HUB USB-C Charging Port OTG Adapter UK | eBay
No Audio out via HDMI on this product.
Video Output was 1080p @60fps
Sorry for the bad video; as it was taken with my Nexus 7.
https://youtu.be/Iuf1YoBzzn8
Click to expand...
Click to collapse
[Cruzer] said:
Thanks for this, will be ordering one myself now.
edit: no audio out on this device, well then that sucks. Not good for watching video, yah I know I probably can use headphone jack for that but should work that way in my opinion. guess I'll still be on the hunt for a simple HDMI and audio output like the good old MHL adapter.
Click to expand...
Click to collapse
I was wrong about audio, it works fine on a TVs but for some reason not on my monitor with HDMI?
1stGGMan said:
I was wrong about audio, it works fine on a TVs but for some reason not on my monitor with HDMI?
Click to expand...
Click to collapse
ok thanks, i'll go ahead and get one and test myself.. thanks again for the info.
Pls ask me! For 5Gbps UBS 3.1 Type-C to 4K HDMI USB 3.0 HUB USB-C Charging Port OTG Adapter UK support any cable HDMI?
Sorry my English
1stGGMan said:
Hi
Here a very quick video of my HTC 10 working on HDMI while being charged.
5Gbps UBS 3.1 TypeC to 4K HDMI USB 3.0 HUB USBC Charging Port OTG Adapter UK 5Gbps UBS 3.1 Type-C to 4K HDMI USB 3.0 HUB USB-C Charging Port OTG Adapter UK | eBay
No Audio out via HDMI on this product. There is audio just does not work on my monitor via HDMI but works fine on TVs.
Video Output was 1080p @60fps
Sorry for the bad video; as it was taken with my Nexus 7.
https://youtu.be/Iuf1YoBzzn8
Click to expand...
Click to collapse
Is this available anywhere else? I was hoping to find this or a similar device on Amazon or something but nothing else has been confirmed to be compatible. Is your experience with this device still a positive one??
Also, I am assuming that if you want to supply charging power to this device you need to use a non-QuickCharge charger as supplying greater than 5V to the electronics in this device would be bad...? What about still using legacy USB-A to USB-C cables (like the one that came with the HTC 10) with the 56K Ohm resister?
radensb said:
Is this available anywhere else? I was hoping to find this or a similar device on Amazon or something but nothing else has been confirmed to be compatible. Is your experience with this device still a positive one??
Also, I am assuming that if you want to supply charging power to this device you need to use a non-QuickCharge charger as supplying greater than 5V to the electronics in this device would be bad...? What about still using legacy USB-A to USB-C cables (like the one that came with the HTC 10) with the 56K Ohm resister?
Click to expand...
Click to collapse
I use mine all the time at work for about 3-7 hours a night (5 nights a week) - have it plugged into spare monitor to watch youtube etc.
I using the default charger that came with the HTC 10 and only gets slightly warm (charger & adaptor) when I been playing games for a hour or two.
Been thinking about purchasing another one as a backup.
I had some initial difficulty getting a micro usb OTG cable working, I ended up testing a few and thought I would share in case it saves anyone else some time or money.
if anyone else has adapters they've tried feel free to list them
I actually haven't tried a straight USB type C OTG cable yet, all have been micro USB OTG units with a micro USB to type C converter since I already had so many lying around.
First off I should mention not all micro usb to USB type C converters support OTG.
this Meenova one does and works with the oneplus 3t: https://www.amazon.com/gp/product/B018G6IK7E/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
with that converter pretty much any OTG adapter will work.
Charging also works.
This micro USB OTG adaptor is nice because its so low profile.
I tested it with a flash drive and it works fine with the Meenova adapter listed above.
https://www.amazon.com/gp/product/B0196FG4DG/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
This Samsung adapter also works well with the Meenova adapter, it has quite a few features which I tested on the Oneplus 3t, its expensive though so unless you have a Samsung tablet as well its not likely to be worth it for most people:
built in features:
two USB ports
Ethernet port
Charging port for simultaneous charging and OTG
On the Oneplus 3t both charging and OTG work fine but not at the same time.
whichever you plug in first is what it will use until you unplug and re-plug in the adapter.
That being said my understanding is that this is likely just a kernel limitation, it was the same way on the nexus 7 and a custom kernel enabled the simultaneous charging.
I'm not sure how useful that would be on a phone but I thought I would mention it.
Both USB ports work simultaneously, I connected two flash drives and both were picked up by the phone right away.
I wasn't able to get the Ethernet port working, or at least there was no indicator that it was working (My samsung tablet gives a notification that the Ethernet is plugged in but Samsung may have added that, I'm not sure) I'll play with it some more later.
Adaptor link: https://www.amazon.com/gp/product/B00J2N0GB4/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
and lastly I tried this micro USB to type c adapter and charging works but OTG does not:
https://www.amazon.com/gp/product/B0191FRCAA/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Thanks for your post about OTG adapters. Do you have any updates on this issue? I'm looking for possible adapters but cannot find any.
The Meenova adapter is not available in Europe and also seems not to be available from Amazon.com anymore. I can also disadvise from Anker USB adapter because it doesn't work.
What I'm looking for is an USB typ-C to microUSB adapter for audio output via USB.
Anker adapter supports dash charge (works with oppo vooc power bank). I am trying OTG now, but I have some cheap OTG dongle (https://www.aliexpress.com/item/5pc...G-adapter-for-HTC-for-Samsung/1734417126.html) and I am not sure if it works at all Anyway OTG via Anker is not working for me at this moment.
mmmm1234 said:
Thanks for your post about OTG adapters. Do you have any updates on this issue? I'm looking for possible adapters but cannot find any.
The Meenova adapter is not available in Europe and also seems not to be available from Amazon.com anymore. I can also disadvise from Anker USB adapter because it doesn't work.
What I'm looking for is an USB typ-C to microUSB adapter for audio output via USB.
Click to expand...
Click to collapse
i have this one
http://www.ebay.co.uk/itm/381793306261
Black / For One Plus Two 2 3 (that's what it says in the drop down)
my Fiio E10k headphone amplifier works with it if that's what you're looking for
reubenbubu said:
i have this one
Black / For One Plus Two 2 3 (that's what it says in the drop down)
my Fiio E10k headphone amplifier works with it if that's what you're looking for
Click to expand...
Click to collapse
Thanks! Though it's USB type B. I need micro USB.
In case anyone was unaware....Came across a video on YouTube and found out that one of the adapters that came with the phone, USB-C to USB Female-which was part of the SmartSwitch, turn out that it is an OTG adapter.
You can use it to connect thumb drive, usb harddrive, usb hub, keyboard and mouse...It even lets you charge another device from your phone.
The microUSB adapter is just that an adapter not OTG ....I did find a 2 pack OTG adapter for USB-C to microUSB on amazon for $7 and have verified they work too. USB 3.1 Type-C to MicroUSB 2.0 Female OTG Adapter, Gray, pack of 2, for Google Pixel/Pixel XL, Nexus 5X/6P, LG G5, Moto Z, HTC m10 & others
I think this is detailed as an OTG adapter within the owners manual anyway