S4 Mini (GT-i9190) Help me - S.O.S ... debrick.img - Galaxy S 4 Mini Q&A, Help & Troubleshooting

Hi guys!!!
I m new here and i have a big problem and i think you can help me.
My galaxy S4 mini (gt-i9190) dead. I wasnt able to turn in on, charge it, there was no respond so it was completely dead. Only when I connect to pc recognized driver.
I found some solution with debrick image here on forum (debrick_4.4.2, but when i putted debrick.img (found some for I9190 android 4.4.2 on web) into sd card via win32diskmanager and inserted it into my phone i was able to get some respond by a phone.
Withou debrick image on sd cart i can't turn my phone on at all but with inserted debrick image i have a chance to turn it on but with some kind of boot loop.
With debrick image on sd cart i can put my phone in odin mode but i can t do nothhing with it. When I connect my phone in ODIN, it recognizes, i can install a rom (firmware 4.4.2 by sammobile) satisfactorily. But my phone now when i try put it in recovery booting only i see this .... (recovery booting ... set warranty bit: recovery after see android imagen lying and this phrase ... any commands)
Help meeeee pls!!!

Hi mate.....did u find the solution?

Related

How to unbrick Samsung galaxy 551

A black screen only, no download mode, no recovery mode, no emergency.
Congratulations, you have brick your phone. You will need a android pc cable.
1.Remove Battery, SIM card, SD card and attach phone to USB .
2.Then pressing Q+power attach battery after 10 sec. and see if odin detects it well and good.
Thanks
Hi, your unbrick manual don't working. I have bricked 551.
Sorry,
Your phone is very hard bricked
You need to go to the Samsung care

[Q] Hard Brick i747 AT&T SD unbrick???

@edit i whrited the wrong model.....it I747 NOT 797
Again....excuse if i'm posting on the wrong place cause i'm really newbie on this forum things......
My problem is that while tring to reinstall my 4.3 droid i went to this thread http://forum.xda-developers.com/showthread.php?t=2498233 and tried using these files to get another rom, so as it mentioned i started flashing the boot loader but via odin i coudn't as odin negated to proceed due to errors. Them i triede odin multiloader them i tried TWRP them i ended up messing everythin tring via Clock work mod recovery. I just got the process well done and them when the system tries to boot it just won't boot. The eternal black screen looks like i have to a Hard Brick and even if while i try the usb cable the computer responds to the device, i couldn't take it to Download Mode.
After some research i have see that it's possible to make a debrick via SD card.
So.....i'm exactly........cring for help, any good soul that have a litle time to explain me a couple things if i can or i cannot debrick it without spending money. IS my time is running cause i got my SIM card cut and this is my only phone now.
Sorry again for anything.......hope somthing comes but while it not come i will keep researching thanks verybody.
@update Now i'm stuck on how to get to a folder on the terminal of ubuntu to mount the img file to the sd card
Farahjr said:
Again....excuse if i'm posting on the wrong place cause i'm really newbie on this forum things......
My problem is that while tring to reinstall my 4.3 droid i went to this thread http://forum.xda-developers.com/showthread.php?t=2498233 and tried using these files to get another rom, so as it mentioned i started flashing the boot loader but via odin i coudn't as odin negated to proceed due to errors. Them i triede odin multiloader them i tried TWRP them i ended up messing everythin tring via Clock work mod recovery. I just got the process well done and them when the system tries to boot it just won't boot. The eternal black screen looks like i have to a Hard Brick and even if while i try the usb cable the computer responds to the device, i couldn't take it to Download Mode.
After some research i have see that it's possible to make a debrick via SD card.
So.....i'm exactly........cring for help, any good soul that have a litle time to explain me a couple things if i can or i cannot debrick it without spending money. IS my time is running cause i got my SIM card cut and this is my only phone now.
Sorry again for anything.......hope somthing comes but while it not come i will keep researching thanks verybody.
Click to expand...
Click to collapse
yes you can use your sd card to revive your AT&T Samsung Galaxy S3 I747 assuming thats what you have
2nd always research before you flash or modify your phone
3rd if you can get your phone into download mode then its not hard bricked ....shutdown device and then (hold the power button + home button + volume down button at the same time) wait until the phone lights up with the download page
4th odin back to stock (sorry am too tired to find one) start from here http://forum.xda-developers.com/showthread.php?t=1725839
5th if its bricked try this thread http://forum.xda-developers.com/showthread.php?t=2525902&page=3
hope that helps
edit: if that does not help use this link http://forum.xda-developers.com/showthread.php?t=2345860
get a usb jtag if you cant access download mode
doesnt work Mobiletechvideos.com is there to debrick your phone for a good price
winosxbuntu said:
yes you can use your sd card to revive your AT&T Samsung Galaxy S3 I747 assuming thats what you have
2nd always research before you flash or modify your phone
3rd if you can get your phone into download mode then its not hard bricked ....shutdown device and then (hold the power button + home button + volume down button at the same time) wait until the phone lights up with the download page
4th odin back to stock (sorry am too tired to find one) start from here http://forum.xda-developers.com/showthread.php?t=1725839
5th if its bricked try this thread http://forum.xda-developers.com/showthread.php?t=2525902&page=3
hope that helps
Click to expand...
Click to collapse
1-Yes it's a AT&T i747 as i had my self upgrading downgrading upgrading again and rooteing the device the last time. I think that i possibly flashed something on these steps that gave me this problem after tring to flash the method on the link that i mentioned.
5- It's hard bricked cause i can't go into download mode. I'm reading this http://forum.xda-developers.com/showthread.php?p=43305728
I forgot to say....i'm not helpfull with the thecnical english language. I'm a braziliam and i really to only get the most simple threads that i can just in case to not comit any mistakes due to language issues.
My nightmares have come.......so i'm just installing a Virtual Machine fo Ubuntu and try to load the img to an 8gb SD series 4 i know that the recomended is 16 gb 10 series but i will try the process anyway just to get experience.
But still wanna help if anybody comes with more! thanks!
Farahjr said:
1-Yes it's a AT&T i747 as i had my self upgrading downgrading upgrading again and rooteing the device the last time. I think that i possibly flashed something on these steps that gave me this problem after tring to flash the method on the link that i mentioned.
5- It's hard bricked cause i can't go into download mode. I'm reading this http://forum.xda-developers.com/showthread.php?p=43305728
I forgot to say....i'm not helpfull with the thecnical english language. I'm a braziliam and i really to only get the most simple threads that i can just in case to not comit any mistakes due to language issues.
My nightmares have come.......so i'm just installing a Virtual Machine fo Ubuntu and try to load the img to an 8gb SD series 4 i know that the recomended is 16 gb 10 series but i will try the process anyway just to get experience.
But still wanna help if anybody comes with more! thanks!
Click to expand...
Click to collapse
cry a little, maybe the phone will accept your apologizes and resurrect from the dead
again it may not work so don't get your hopes up to high ITS A TRIAL AND ERROR situation WITH HARD BRICKS...........
some people have successfully debricked their device, so again you have to be patient and know exactly what you are doing and dont panic
Remember Mobiletechvideos.com can fix it in less than 25 minutes depending on your phone :laugh:and they are affordable :good:
Your pretty much stuck if you can't recover via SD card.
Remember there are a lot of options for JTAG repair, research local repairs by Kijiiji and also places like Mobile Tech Videos. Always search for legitimacy and best price.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
winosxbuntu said:
cry a little, maybe the phone will accept your apologizes and resurrect from the dead
again it may not work so don't get your hopes up to high ITS A TRIAL AND ERROR situation WITH HARD BRICKS...........
some people have successfully debricked their device, so again you have to be patient and know exactly what you are doing and dont panic
Remember Mobiletechvideos.com can fix it in less than 25 minutes depending on your phone :laugh:and they are affordable :good:
Click to expand...
Click to collapse
I'm almost crying. As a brazilian those devices are a litle difficult to access as i should need to import and the Dollar is expensive for me that's why i will try every way it's possible before tring someeone that have a box on brazil and pay for it.
Now i'm stuck on how to get to a folder on the terminal of ubuntu to mount the img file.
@update i have done with the burning img thing. It won't worked but i shall try again tomorrow with a 16GB serie 10 SD card!
Octopus
Farahjr said:
I'm almost crying. As a brazilian those devices are a litle difficult to access as i should need to import and the Dollar is expensive for me that's why i will try every way it's possible before tring someeone that have a box on brazil and pay for it.
Now i'm stuck on how to get to a folder on the terminal of ubuntu to mount the img file.
@update i have done with the burning img thing. It won't worked but i shall try again tomorrow with a 16GB serie 10 SD card!
Click to expand...
Click to collapse
I couldn't get a card with those parameters........
For my lucky......my company has purchased an octopus box that supports SGH-I747...i never used this before never saw never touched i'm just reading tutorials but a i couldn't find any tutorial about unbricking with the box. Any one know if it's possible to solve this easily via box???
Farahjr said:
I couldn't get a card with those parameters........
For my lucky......my company has purchased an octopus box that supports SGH-I747...i never used this before never saw never touched i'm just reading tutorials but a i couldn't find any tutorial about unbricking with the box. Any one know if it's possible to solve this easily via box???
Click to expand...
Click to collapse
Octopus box will not do this work in contact with the support so now i am waiting for the arive of the micro SD 16 GB class10. Will update the post when it arrives.
Farahjr said:
Octopus box will not do this work in contact with the support so now i am waiting for the arive of the micro SD 16 GB class10. Will update the post when it arrives.
Click to expand...
Click to collapse
Tried via sd but nothing happened.
Will try again with another image and charging the battery.
winosxbuntu said:
yes you can use your sd card to revive your AT&T Samsung Galaxy S3 I747 assuming thats what you have
2nd always research before you flash or modify your phone
3rd if you can get your phone into download mode then its not hard bricked ....shutdown device and then (hold the power button + home button + volume down button at the same time) wait until the phone lights up with the download page
4th odin back to stock (sorry am too tired to find one) start from here http://forum.xda-developers.com/showthread.php?t=1725839
5th if its bricked try this thread http://forum.xda-developers.com/showthread.php?t=2525902&page=3
hope that helps
edit: if that does not help use this link http://forum.xda-developers.com/showthread.php?t=2345860
get a usb jtag if you cant access download mode
doesnt work Mobiletechvideos.com is there to debrick your phone for a good price
Click to expand...
Click to collapse
Is it 100% chance to get in to download mode via JIG????
I'm having trouble tring to refind the all the possible debrick images that I should try so i'm thinking about doing a JIG by my self. Any free solution i will try before spending any Money on something I don't know if will really work.
Farahjr said:
Is it 100% chance to get in to download mode via JIG????
I'm having trouble tring to refind the all the possible debrick images that I should try so i'm thinking about doing a JIG by my self. Any free solution i will try before spending any Money on something I don't know if will really work.
Click to expand...
Click to collapse
if its hard bricked then its a 50/50 chance, i would recommend trying to boot using the debrick.img on the SD-CARD and hope some magic will happen otherwise yu might have to spend some money to fix or just buy a new phone
Can’t access to Download Mode or Recovery Mode after bricking AT&T Galaxy S3 i744 4.3
Hi I have (had) a AT&T galaxy S3 i747 with android 4.1.1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Because the phone is in another country I couldn’t update it by OTA to android 4.3
So I started to read forums that said how to Update AT&T S3 i747 to android 4.3 (I747UCUEMJB)
The S3 was not Root
I installed all the phone drivers in the computer
This is what I did: (http://forum.xda-developers.com/showpost.php?p=52341582&postcount=38)
- Use Odin 3.07
- Check Auto Reboot and Re-Partition, and uncheck all the boxes
- I put my phone in USB debugging in the developer options
- I turned it off
- Started to put the phone on Download Mode pressing volume DW+home+power button at the same time
- In Odin on the PDA box I checked and loaded the file .tar.md5 (I747UCUEMJB_2024954_REV04_user_low_ship.tar.md5 )
- Pressed the button Start
The installation seemed to go right, the program never showed anything weird.
When the Programs finished the installation the phone turned off and then turned on and show the logo of android (seemed to be lying down or inclined) and after that it turned off.
The computer showed that something was connected (QHSUSB_DLOAD) but couldn’t install any driver, so I disconnected it of the computer.
I couldn’t turn on the phone :crying:, I took the battery out and put it in and tried to start the phone and nothing happened, I tried pressing any button to access to recovery o download mode and none of this worked.
I started to search forums that talk about restart or turn on a brick AT&T S3 i747
I found one (http://forum.xda-developers.com/showthread.php?t=2549068) that said to download a image (debrick-SGH-I747U-CUEMJB3.img) and using the program “Win32DiskImager” to put the image inside of a micro SD to make the phone turn on,
I put the micro SD inside the phone and when I pushed the power button for almost 3 seconds it Turned on , the phone seems to be fine an it has android 4.3 (I747UCUEMJB) installed.
I can use it normally so far.
But the problem is that I can’t turn on the phone if the micro SD card is not inserted on the phone.
Without the micro SD inside don’t show any sign of life
When the micro SD is inside I can turn on the phone and use its apps.
I have tried to enter to Recovery mode or Download mode with the micro SD inside but the phone only show what its supposed to happen for 1 second then turns off and then turns on by its own (after that I can use it normally)
Does anyone know how can I Fix my phone ?
How can I boot my phone without using the micro SD card?
How can I access to download mode?
And if I could access to download mode what should I do next ?
The only files I have now are:
Odin3 v3.07
I747UCUEMJB_2024954_REV04_user_low_ship.tar.md5(905 Mb)
debrick-SGH-I747U-CUEMJB3.img (80 Mb)
I747
winosxbuntu said:
if its hard bricked then its a 50/50 chance, i would recommend trying to boot using the debrick.img on the SD-CARD and hope some magic will happen otherwise yu might have to spend some money to fix or just buy a new phone
Click to expand...
Click to collapse
It's been a while sorry about beinging away.
A guy who says that have a JTAG service tried and coudn't recover it. So I left it there because it have a broken display and a broken firmware and it' is from outside Brazil and after the FIFA CUP Anatel will lock operation of devices that models are not sold on Brazil and I747 is probably included on the list.
So i gave up from my phone and bought a Nexus 5.
The case is closed!
Maralex1520 said:
Hi I have (had) a AT&T galaxy S3 i747 with android 4.1.1 View attachment 2790321
Because the phone is in another country I couldn’t update it by OTA to android 4.3
So I started to read forums that said how to Update AT&T S3 i747 to android 4.3 (I747UCUEMJB)
The S3 was not Root
I installed all the phone drivers in the computer
This is what I did: (http://forum.xda-developers.com/showpost.php?p=52341582&postcount=38)
- Use Odin 3.07
- Check Auto Reboot and Re-Partition, and uncheck all the boxes
- I put my phone in USB debugging in the developer options
- I turned it off
- Started to put the phone on Download Mode pressing volume DW+home+power button at the same time View attachment 2790322 View attachment 2790323
- In Odin on the PDA box I checked and loaded the file .tar.md5 (I747UCUEMJB_2024954_REV04_user_low_ship.tar.md5 )
- Pressed the button Start View attachment 2790324
The installation seemed to go right, the program never showed anything weird. View attachment 2790325
When the Programs finished the installation the phone turned off and then turned on and show the logo of android (seemed to be lying down or inclined) and after that it turned off.
The computer showed that something was connected (QHSUSB_DLOAD) but couldn’t install any driver, so I disconnected it of the computer.
I couldn’t turn on the phone :crying:, I took the battery out and put it in and tried to start the phone and nothing happened, I tried pressing any button to access to recovery o download mode and none of this worked.
I started to search forums that talk about restart or turn on a brick AT&T S3 i747
I found one (http://forum.xda-developers.com/showthread.php?t=2549068) that said to download a image (debrick-SGH-I747U-CUEMJB3.img) and using the program “Win32DiskImager” to put the image inside of a micro SD to make the phone turn on,
I put the micro SD inside the phone and when I pushed the power button for almost 3 seconds it Turned on , the phone seems to be fine an it has android 4.3 (I747UCUEMJB) installed.View attachment 2790326
I can use it normally so far.
But the problem is that I can’t turn on the phone if the micro SD card is not inserted on the phone.
Without the micro SD inside don’t show any sign of life
When the micro SD is inside I can turn on the phone and use its apps.
I have tried to enter to Recovery mode or Download mode with the micro SD inside but the phone only show what its supposed to happen for 1 second then turns off and then turns on by its own (after that I can use it normally)
Does anyone know how can I Fix my phone ?
How can I boot my phone without using the micro SD card?
How can I access to download mode?
And if I could access to download mode what should I do next ?
The only files I have now are:
Odin3 v3.07
I747UCUEMJB_2024954_REV04_user_low_ship.tar.md5(905 Mb)
debrick-SGH-I747U-CUEMJB3.img (80 Mb)
Click to expand...
Click to collapse
Here's what you can do to get the device back to working and booting normally. If the Odin flash failed first time, you should not use this flash again. Instead you should use custom recovery to flash a complete 4.3 stock restore image.
1) Download the stock restore image from the following thread. I always prefer to use TWRP and thus, the TWRP image, because of the easier user interface.
http://forum.xda-developers.com/showthread.php?t=2658486
Save the file to a location on your computer.
2) Download the Odin flashable TWRP Tar file for custom recovery from the link below ....
http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.1-d2att.tar
With the debrick card in your phone, boot to system as you have been doing. Connect your phone to your computer with a good quality micro USB cable and copy the stock restore image you downloaded earlier to your phone. Be sure you remember the stored location.
3) Power off your phone and, with the debrick card, boot to download mode. If you cannot use the Volume Down, Power and Home button combo to boot to download mode, you may need to get a USB jig.
4) Once you are in download mode, connect your phone to the PC, open Odin v3.07. Make sure Odin recognizes your phone. Do not check or uncheck any boxes but leave the defaults as is. In the PDA box, load the TWRP Tar file you downloaded earlier. Click on Start and wait for flashing to complete. When you get to Pass, disconnect your phone from the PC and pull out the battery to stop it trying to reboot.
5) Replace the battery and with the debrick card inside, boot to Recovery mode by pressing the Volume Up, Power and Home buttons. If you do this right, you should be able to get to recovery mode.
6) Select Install and navigate to the stock restore zip file you saved to your phone earlier. Select this zip and swipe to confirm install. Wait for firmware installation (flashing) to complete.
7) Clear your cache/dalvikand reboot to system.
Try booting without the card. If the above process went as described, your phone should be booting normally. Good luck!
Stuck in AT&T logo
Larry2999 said:
Here's what you can do to get the device back to working and booting normally. If the Odin flash failed first time, you should not use this flash again. Instead you should use custom recovery to flash a complete 4.3 stock restore image.
1) Download the stock restore image from the following thread. I always prefer to use TWRP and thus, the TWRP image, because of the easier user interface.
http://forum.xda-developers.com/showthread.php?t=2658486
Save the file to a location on your computer.
2) Download the Odin flashable TWRP Tar file for custom recovery from the link below ....
http://techerrata.com/file/twrp2/d2att/openrecovery-twrp-2.6.3.1-d2att.tar
With the debrick card in your phone, boot to system as you have been doing. Connect your phone to your computer with a good quality micro USB cable and copy the stock restore image you downloaded earlier to your phone. Be sure you remember the stored location.
3) Power off your phone and, with the debrick card, boot to download mode. If you cannot use the Volume Down, Power and Home button combo to boot to download mode, you may need to get a USB jig.
4) Once you are in download mode, connect your phone to the PC, open Odin v3.07. Make sure Odin recognizes your phone. Do not check or uncheck any boxes but leave the defaults as is. In the PDA box, load the TWRP Tar file you downloaded earlier. Click on Start and wait for flashing to complete. When you get to Pass, disconnect your phone from the PC and pull out the battery to stop it trying to reboot.
5) Replace the battery and with the debrick card inside, boot to Recovery mode by pressing the Volume Up, Power and Home buttons. If you do this right, you should be able to get to recovery mode.
6) Select Install and navigate to the stock restore zip file you saved to your phone earlier. Select this zip and swipe to confirm install. Wait for firmware installation (flashing) to complete.
7) Clear your cache/dalvikand reboot to system.
Try booting without the card. If the above process went as described, your phone should be booting normally. Good luck!
Click to expand...
Click to collapse
Hi thanks for the solution, it worked now i dont need the micro SD to boot the S3 but now i have a problem, i can turn on the phone normally but it stucks in the AT&T logo and after that the phone turns off so i can not accsess to apps. I hope you can help me to fix this problem
Maralex1520 said:
Hi thanks for the solution, it worked now i dont need the micro SD to boot the S3 but now i have a problem, i can turn on the phone normally but it stucks in the AT&T logo and after that the phone turns off so i can not accsess to apps. I hope you can help me to fix this problem
Click to expand...
Click to collapse
Okay. At least, we are almost there. Try booting into recovery mode and doing a hard wipe/reset. If this doesn't work, then you could try reinstalling the 4.3 stock firmware. You may need to reflash custom recovery as the initial flashing would have returned you to stock recovery. If you have to do the firmware flashing again, please make sure you clear your cache/dalvik before rebooting to system.
happy to see this thread resolved, this is what XDA is all about, no matter how fd up something sounds, a community like xda will find a fix for it even if it takes months
And the award of the Q/A thread goes to Larry and everyone in this post for trying and failing but succeeding at the end :laugh:
anywayz happy rooting and be careful, no-one wants to end with a brick cheers and keep this place awsome
Galaxy S3 i747 fixed after hardbrick
Larry2999 said:
Here's what you can do to get the device back to working and booting normally. If the Odin flash failed first time, you should not use this flash again. Instead you should use custom recovery to flash a complete 4.3 stock restore image.
1) Download the stock restore image from the following thread. I always prefer to use TWRP and thus, the TWRP image, because of the easier user interface.
http://forum.xda-developers.com/show....php?t=2658486
Save the file to a location on your computer.
2) Download the Odin flashable TWRP Tar file for custom recovery from the link below ....
http://techerrata.com/file/twrp2/d2a....3.1-d2att.tar
With the debrick card in your phone, boot to system as you have been doing. Connect your phone to your computer with a good quality micro USB cable and copy the stock restore image you downloaded earlier to your phone. Be sure you remember the stored location.
3) Power off your phone and, with the debrick card, boot to download mode. If you cannot use the Volume Down, Power and Home button combo to boot to download mode, you may need to get a USB jig.
4) Once you are in download mode, connect your phone to the PC, open Odin v3.07. Make sure Odin recognizes your phone. Do not check or uncheck any boxes but leave the defaults as is. In the PDA box, load the TWRP Tar file you downloaded earlier. Click on Start and wait for flashing to complete. When you get to Pass, disconnect your phone from the PC and pull out the battery to stop it trying to reboot.
5) Replace the battery and with the debrick card inside, boot to Recovery mode by pressing the Volume Up, Power and Home buttons. If you do this right, you should be able to get to recovery mode.
6) Select Install and navigate to the stock restore zip file you saved to your phone earlier. Select this zip and swipe to confirm install. Wait for firmware installation (flashing) to complete.
7) Clear your cache/dalvikand reboot to system.
Try booting without the card. If the above process went as described, your phone should be booting normally. Good luck!
Click to expand...
Click to collapse
Hey Larry2999 I want to really thank you for your help it was so helpful, actually I discovered that the battery of the Galaxy S3 was failing thats why when I turned on the phone it turned off after a seconds althoughthe battery was charged, so I connected the charger to the phone and it started normally. Now I can use it and it has android 4.3.
Your method was right, and thanks to take the time to answer. I hope it can help someone else too.
Maralex1520 said:
Hi thanks for the solution, it worked now i dont need the micro SD to boot the S3 but now i have a problem, i can turn on the phone normally but it stucks in the AT&T logo and after that the phone turns off so i can not accsess to apps. I hope you can help me to fix this problem
Click to expand...
Click to collapse
Hey I cannot get into download mode, and I´m exactly in the same problem you were. How did you get into download mode? I haven´t used usb JIG since I cannot get one from where i live.
I´ll be really thankful in you help me!:angel:
Maralex1520 said:
Hey Larry2999 I want to really thank you for your help it was so helpful, actually I discovered that the battery of the Galaxy S3 was failing thats why when I turned on the phone it turned off after a seconds althoughthe battery was charged, so I connected the charger to the phone and it started normally. Now I can use it and it has android 4.3.
Your method was right, and thanks to take the time to answer. I hope it can help someone else too.
Click to expand...
Click to collapse
Glad to know it's working fine now.
---------- Post added at 03:02 PM ---------- Previous post was at 03:01 PM ----------
feta9310 said:
Hey I cannot get into download mode, and I´m exactly in the same problem you were. How did you get into download mode? I haven´t used usb JIG since I cannot get one from where i live.
I´ll be really thankful in you help me!:angel:
Click to expand...
Click to collapse
Did you try getting into download mode with the 3-button combo (Volume Down/Power/Home)?

N7105 - SDCard Mode and ODIN

Hi I managed to to get to SDCARD Download mode from a dead boot N7105 using the SD Boot Repair SD. Odin recognizes this and phone was previously on 4.3 JellyBean already. Now when I'm trying to flash with Odin 3.09 , it says "There is no PIT partition" . Should I click the Phone Bootloader Update checkbox also? Need some advice from all the gurus here to guide me along this, thank you very much
Hi guys,
I have a very similar scenario but with an Samsung Galaxy S3 i9300:
Couple of days ago my phone went into booting loop but after removing the battery for a couple of minutes the issue was solved.
Then 3 days later it restart out of the sudden and was stuck on the Samsung Galaxy S III splash screen.
I rebooted and tried putting the phone in Download mode. The phone went into the Samsung Galaxy S III screen twice and turn off not to boot again. Seems like a hard bricked, no response with any buttons combinations.
I read other posts here saying that I could probably boot the phone with an micro sd card. So I donwloaded image I9300UBUGML1_I9300UWHUGMK1_I9300UBUGMK1_HOME from SamMobile and mouted in a 16 Gb type 10 micro SD (my phone is also 16 Gb version)
At first I tried booting the phone pressing the power button for about 10 seconds and the screen ligthted up very quickly (less than a second) saying
SDCARD MODE
UP KEY: NORMAL BOOTING
DOWN KEY: DOWNLOAD MODE
But it was so quick that I was not able to press anything.
A day later I figure out that if I was quick enough I could press down key and put the phone on Download mode (SDCARD)
After putting the phone on Download mode I connected the phone to the PC and tried flashing it with ODIN v3.07
Odin is able to see the device but when trying to flash the phone (selecting PDA and the image mention before) a message came up saying:
There is no PIT partition
And failed.
Reading about this error in this forum, I have tried using different PIT files to re-partion the phone but no success so far.
GT-I9300_mx_20120220.pit
GT-I9300_mx_20120322.pit
GT-I9300_mx_20120329.pit
mx.pit
Odin stays on Get PIT for mapping after initializing the process.
I would like to know if anyone here have an idea on what else to try (before talking about JTAG reparing the phone as I am not 100% the phone is hard bricked)
I have not attempted to use a USB Jig yet, should I?
Other details:
I am not able to get the download with any other image file in the sd card.
If the phone is on download mode and connected to the PC, the battery can be removed and the phone stays on.
If I press up key in the SD CARD Mode the phone freezes.
Do you guys have any ideas here?
Thanks,

[Q] Debrick.img Needed Hard Bricked I9195, N Dload mode, No Recovery

My Samsung galaxy s 4 mini bricked it self apparently. STOCK ROM 4.2.2
It was rooted nothing more, only some small mods for the framework.
put my phone to charge and went to sleep. was late to because the alarm didn't ring. i took my phone to check why it didn't ring, and nothing. no light, no sound nothing. i took out the battery put it back in try to start nothing.
Anyway it doesn't get detected by odin, can't access download mode nor recovery mode. Only thing when connected to pc is installs driver for QHSUSB_DLOAD. I have tried different ways to fix it and the only way without sending my phone somewhere to service is to boot the phone through sdcard.
http://forum.xda-developers.com/attachment.php?attachmentid=2541005&d=1390771555
ValenteL has provided a .zip file that you run in recovery either which one you have and it should give a .img file at the size of 128mb into your sdcard
Those who have the debrick.img file from a stock 9195 4.2.2, would you be kind and sen it to me so that i can try fix my s4 mini
also i have already tried a debrick.img but from a 9192 don't know the firmware version but it didn't do anything
Here you go. http://d-h.st/XK5V .. Extract the downloaded file and u will get img file in a folder.
sasank360 said:
Here you go. http://d-h.st/XK5V .. Extract the downloaded file and u will get img file in a folder.
Click to expand...
Click to collapse
Thanks for the debrick image but it seems my phone it totally bricked only JTAG or a real service could fix it. if you have any knowledge in this part could it be that the sdcard i used are too slow? i have used 16GB class 2 and a 8GB class 4, still no sign.
Edit: 16GB class 2 and 8GB class 4 works fine for boot through sdcard
I could say it has progressed a little i am using the 16GB class 2 sdcard and when i plug it to the computer the phone vibrates but no qhsusb_dload is detected and odin also finds nothing
Edit: When the phone vibrates it indicates that it is turned on, mine only took a little while to go to the boot recovery mode but failed to boot the os and switched mode to either factory mode or odin mode.
The Debrick.img worked fine just need to hold down power button for like 10-15 seconds. but it seems like my phone has a broken partition, i9195 connects to odin but cannot be flashed because of, false pit file? i have read that the pit file needs to correspond to the gb model the phone is and the firmware version for instance 16GB 4.2.2, so now i need a .pit file to be able to continue the recovering process of my phone.
It is better to use a class 10 sd card.
Check the general section for the thread that explains how to unbrick using pit file.
Hey my Phone just vibrates but there is nothing on the screen and my computer downst detect anything how did you get through that vibration
Link Down
Hey, could you please provide another link for the image? Dev-host won't work anymore...
DamnedSon said:
Hey, could you please provide another link for the image? Dev-host won't work anymore...
Click to expand...
Click to collapse
can someone send working debrick.img ??
i found one on net but not work for my i9195. I was trying with 16gb class 4 and 128gb XC 1 and different card adapters and no success. nothing to appear on my device, i was trying with power button and with USB JIG and nothing. When i plug device to PC nothing appears. but when I put it to PC without microsd appears qhsusb_dload. I dont uderstand why this not work for me.
Here are all events:
1) no microsd with battery => Qualcomm HS-USB QDLoader 9008 (COM4) and after 10 sec disconnect
2) no microsd without battery => USB Input Device and after 5 sec disconnect and than Qualcomm HS-USB QDLoader 9008 (COM4) and after 7 sec disconnect
3) with microsd with battery => nothing happen
4) with microsd without battery => USB Input Device and after 5 sec reconnect and again again again .... infinity...
this makes me crazy, what to do?? i am on windows 10
cro.dev said:
can someone send working debrick.img ??
i found one on net but not work for my i9195. I was trying with 16gb class 4 and 128gb XC 1 and different card adapters and no success. nothing to appear on my device, i was trying with power button and with USB JIG and nothing. When i plug device to PC nothing appears. but when I put it to PC without microsd appears qhsusb_dload. I dont uderstand why this not work for me.
Here are all events:
1) no microsd with battery => Qualcomm HS-USB QDLoader 9008 (COM4) and after 10 sec disconnect
2) no microsd without battery => USB Input Device and after 5 sec disconnect and than Qualcomm HS-USB QDLoader 9008 (COM4) and after 7 sec disconnect
3) with microsd with battery => nothing happen
4) with microsd without battery => USB Input Device and after 5 sec reconnect and again again again .... infinity...
this makes me crazy, what to do?? i am on windows 10
Click to expand...
Click to collapse
Hi
i've found this 2
- debrick.img 4.4.2 -> LINK (https://mega.nz/#!T9hxAJQC!e74HQeHhU66fmPFVFOLdxTtFyR-fxntfc37qFb22oRA)
- debrick.img 4.2.2 -> LINK (http://d-h.st/XK5V)
you can try them
i am in your same situation, i have 4.4.2 nobrand last Firmware I9195XXUCPB1_I9195ITVCPB2_I9195XXUCPB1_HOME.tar.md5
with bootloader CF-Auto-Root-serranolte-serranoltexx-gti9195.tar.md5
but noone of the 2 image make my phone boot again (i see it connect on USB if i dont have the SD CARD inserted)
i have tried some old SD CARD and the last ..i used a "modern" Sandisk Ultra 16GB HC I , and it is a 10 Class
but the recovey boot wont come on !!
and suggestions ?
maybe that 2 debrick img are fault , or it is needed a specific IMG ?
thank you for any help
updage.. i've found other brick images and then i were able to boot my phone ...here
https://www.youtube.com/watch?v=p5J9oW_BV5k
but the phone started to go on continuos reboot.... only once it got stoped on an error message and then i were able to connect wtih ODIN ,just for once to try to flas the boot loader but odin sent me an error of "pit missing" and the the phone got stucked
i could not connect once more becouse now it is again IN CONTINUOS REBOOT STATE during recovery from SD CARD
any one can help me to try to "fix" this ? or have maybe a better image file
thank you
lizthe said:
Hi
i've found this 2
- debrick.img 4.4.2 -> LINK (https://mega.nz/#!T9hxAJQC!e74HQeHhU66fmPFVFOLdxTtFyR-fxntfc37qFb22oRA)
- debrick.img 4.2.2 -> LINK (http://d-h.st/XK5V)
you can try them
i am in your same situation, i have 4.4.2 nobrand last Firmware I9195XXUCPB1_I9195ITVCPB2_I9195XXUCPB1_HOME.tar.md5
with bootloader CF-Auto-Root-serranolte-serranoltexx-gti9195.tar.md5
but noone of the 2 image make my phone boot again (i see it connect on USB if i dont have the SD CARD inserted)
i have tried some old SD CARD and the last ..i used a "modern" Sandisk Ultra 16GB HC I , and it is a 10 Class
but the recovey boot wont come on !!
and suggestions ?
maybe that 2 debrick img are fault , or it is needed a specific IMG ?
thank you for any help
updage.. i've found other brick images and then i were able to boot my phone ...here
https://www.youtube.com/watch?v=p5J9oW_BV5k
but the phone started to go on continuos reboot.... only once it got stoped on an error message and then i were able to connect wtih ODIN ,just for once to try to flas the boot loader but odin sent me an error of "pit missing" and the the phone got stucked
i could not connect once more becouse now it is again IN CONTINUOS REBOOT STATE during recovery from SD CARD
any one can help me to try to "fix" this ? or have maybe a better image file
thank you
Click to expand...
Click to collapse
which .img from link you used for successfull booting up? And which microsd you used? I still havent any success. Can you help me? Thanks
on that youtube page you can find an extenal link to a cloud space where you can find several image
i dont rember wich one worked for me ..i had to try some of them ...but anyway it doesnt matter becouse it depends on your mobile,firmware revision .etc ect
try some of them until you find one
lizthe said:
on that youtube page you can find an extenal link to a cloud space where you can find several image
i dont rember wich one worked for me ..i had to try some of them ...but anyway it doesnt matter becouse it depends on your mobile,firmware revision .etc ect
try some of them until you find one
Click to expand...
Click to collapse
I tried all of them and no one work. Which microsd card you used?
cro.dev said:
I tried all of them and no one work. Which microsd card you used?
Click to expand...
Click to collapse
16gb HC 10
---------- Post added at 04:52 PM ---------- Previous post was at 04:50 PM ----------
lizthe said:
16gb HC 10
Click to expand...
Click to collapse
if you have similar SD i suppose that you have a different BOOT ........and this is the reason you are not able to boot (i hope you "see" your phone connected to the pc in a way becouse i am supposing it ......otherwise your phone is death and nothing works)
lizthe said:
16gb HC 10
---------- Post added at 04:52 PM ---------- Previous post was at 04:50 PM ----------
if you have similar SD i suppose that you have a different BOOT ........and this is the reason you are not able to boot (i hope you "see" your phone connected to the pc in a way becouse i am supposing it ......otherwise your phone is death and nothing works)
Click to expand...
Click to collapse
I bought kingstone 16gb class 10 and tried all images and no success. again same results, if I use 9195l images pc recognize device like without sdcard, if I put 9195 images than pc dont recognize it, and without battery loop. I am not smart now what to do :/ how can I see what was firmware on my device? can i make some image of working s4 mini? because i have one which works. do you turned on device with usb-jig or just by pressing power?
J0SH1X said:
Hey my Phone just vibrates but there is nothing on the screen and my computer downst detect anything how did you get through that vibration
Click to expand...
Click to collapse
For who have same problem :
This means the phone's battery is low. Just charge the battery.
Do you guys have a debrick.img for galaxy s4 mini (19190) 4.2.2 jellybean version?
If you do have debrick.img for s4 mini (19190) 4.2.2 jellybean version pls can i have a link to that, my phone's been dead for over a year now and i can't find a working debrick.img for that model. Pls if you do have let me know. Thank you
link files img ???

I9195 stuck in Recovery mode after hardbrick

Hey, all
New to this forum. My wifes samsung S4 mini La Fleur just died one day and looking it up i found that it was hardbricked. I bought the USB-JIG for the phone and used win32diskimager to write the debrick.img to the SDcard (16gb). It did boot up but it keeps looping the Revocery mode on and on and on.
Text i get is :
BOOT RECOVERY MODE:
CHECK BOOT PARTITIONS.
COPY FROM T-FLASH
BOOT RECOVERY
WRITE 138008 SECTORS
REBOOT
And this just keeps looping over and over. Odin does not detect a device. Windows however keeps giving me the sound that something is connected and then disconnected. Have tried other I9195 debrick.img but non of them even boot the device to recovery. Also installed the Qhsusb_DLOAD driver. Without the SDcard in device manager does detect the phones dloader but not Odin.
Any ideas ?

Categories

Resources