Screen works but the touch is misplaced when i want to click something in the right down corner i have to touch center of the screen.
Is this a software problem ?
Hard Reset dosen't fixit. i've tried.
The touch is not broken in recovery mode each part of screen respond for touch
Related
Hi guys.
I just had a problem with my XDAIIs. After I sync it with my PC and restored the back up files, the touch screen suddenly doesn't work. I reset it to scratch, now I couldn't even proceed with the reinstallation of the OS as I can no longer proceed with the touchscreen alignment..
Im stucked with nothing on my XDAIIs.. any help?
THanks
There is a program called "Remote screen alignment" from Code factory (http://www.codefactory.es/en/products.asp?id=244) which will allow you to skip the alighnment process. This can, however, result in an incorrectly alligned screen (Don't count on entering your pin from the touch screen, use the keyboard instead.)
My touch screen was unable to sense some of the screen which made it useless, after it broke (don't drop it on rocks) I completely replaced the touch screen. This requires some expertese in the use of a soldering iron and how to dismantle your device (Tx-6 required).
Hello,
I'm having a problem with my Arc regarding the touch screen, the bottom part of the screen, where usually the icons and slide bar to unlock are is not working, tapping or sliding on it doesn't work. I was using CM10 originally and I tried flashing a stock firmware to double check whether it is the ROM's problem, but now i'm stuck at the setup wizard because I cannot click on the next button.
I went through the whole wizard once by accident and went into the service test for touch screen, the bottom part of the screen totally cannot be detected at all.
Can I ask that if I need to get one of phone part replaced (because my warrantly ran out), which part should I replace?
Thanks
Sry mate but i think it could be screen problem,the best thing you can do is to send it to service repair and see what they think of you're issue.I hope you'll get it fix cheep.Good luck
Sent from Xperia Arc
Hey there,
sometimes after using phone for days, touch screen dont respond correctly on some specific placed on screen.
for example if i hold down at one point on the screen screen is thinking i press also like 1cm down and jumps up and down.
i will wait to re-produce the problem and post a screen from touchscreen with debug menu *#0*#
happens at least 3 times for now with multiple firmware, since a restart always is the solution i think its a samsung related software problem in stock rom.
Did you apply any screen protectors? Its a common issue with cheap ones
No, i dont have any. Also the its not always at the same position.
My phone is stuck at homescreen (pattern lock) and it only responds to the double tap knock screen on. I tried to draw pattern, tap on emergency call, camera on lock screen and nothing gets registered on touch, except for knock screen on taps when screen gets timeout. The double tap is recognized easily anywhere on the screen. I pulled out battery several times and restarted but same issue. I have also refreshed my stock firmware via LGUP Tool but didn't help.
Basically, my touch is only responding to the knock on tap. Nothing else. I turned camera on via volume down button but touch doesn't work there too. What could be the issue? If the double tap is being registered anywhere on the screen easily why is not registering my touch after screen on!?. Please help!
rektbloodcells said:
My phone is stuck at homescreen (pattern lock) and it only responds to the double tap knock screen on. I tried to draw pattern, tap on emergency call, camera on lock screen and nothing gets registered on touch, except for knock screen on taps when screen gets timeout. The double tap is recognized easily anywhere on the screen. I pulled out battery several times and restarted but same issue. I have also refreshed my stock firmware via LGUP Tool but didn't help.
Basically, my touch is only responding to the knock on tap. Nothing else. I turned camera on via volume down button but touch doesn't work there too. What could be the issue? If the double tap is being registered anywhere on the screen easily why is not registering my touch after screen on!?. Please help!
Click to expand...
Click to collapse
Since no ones answering.
Not a solution or fix.
But have u dropped it. Or anything like that. Had screen replaced.
Seen it happen on the note 5s. Sometimes the flex cable for the lcd can become partially dislodged. Enough for touch not to work. One users only was responding to only 2 touches u till flex was pressed back in. Try usin lg flashtool. Method. Set to board dl and itll take u to the minios where it does a touch screen calibration
Again prob not case. But ive seen it happen
Possibly digitizer failure. But knockon working is weird
TheMadScientist420 said:
Since no ones answering.
Not a solution or fix.
But have u dropped it. Or anything like that. Had screen replaced.
Seen it happen on the note 5s. Sometimes the flex cable for the lcd can become partially dislodged. Enough for touch not to work. One users only was responding to only 2 touches u till flex was pressed back in. Try usin lg flashtool. Method. Set to board dl and itll take u to the minios where it does a touch screen calibration
Again prob not case. But ive seen it happen
Possibly digitizer failure. But knockon working is weird
Click to expand...
Click to collapse
Can you please explain the "Set to board dl and itll take u to the minios where it does a touch screen calibration " in a noob friendly way, there are a lot of lg flash tools I see. Also, no, I haven't dropped the phone or any water damage. It just stopped responding suddenly. Knock is responding smoothly anywhere on the screen. I have flashed the rom to stock, same issue.
9
rektbloodcells said:
Can you please explain the "Set to board dl and itll take u to the minios where it does a touch screen calibration " in a noob friendly way, there are a lot of lg flash tools I see. Also, no, I haven't dropped the phone or any water damage. It just stopped responding suddenly. Knock is responding smoothly anywhere on the screen. I have flashed the rom to stock, same issue.
Click to expand...
Click to collapse
I use the same lg flashtool as lg g2 and 3. Older version. On main menu of flashtool u have a few options upgrade. And board dl. If u leave it. It takes u to the old factory reset status 2. And stays there if u set to board dl its gives fac status 3 and boots what is called mini os. First thing u have to do is touch the screen for a calibration test. Its required before mini os finishes booting. Then reboot as normal. Its kinda hard to explain. Its how i reflash stock firmware back from the g2.
Its always worked so ive never upgraded method across 3 phones.
U might look in restoring stock lg g2 flashtool. And replace with g4 .tot and .dll
Also have to set in device manager set to port 41. When in dl mode
---------- Post added at 01:27 PM ---------- Previous post was at 01:22 PM ----------
rektbloodcells said:
Can you please explain the "Set to board dl and itll take u to the minios where it does a touch screen calibration " in a noob friendly way, there are a lot of lg flash tools I see. Also, no, I haven't dropped the phone or any water damage. It just stopped responding suddenly. Knock is responding smoothly anywhere on the screen. I have flashed the rom to stock, same issue.
Click to expand...
Click to collapse
http://lg-firmware-rom.com/lg-tools-software/lg-flash-tools-flashing-lg-tot-stock-firmware/
I use version 1.81. And download the second file its the .dll to replace in flashtool directory
Hello all,
My Joying HE is starting to lose sensitivity in the touch screen. The bottom and top edges aren't working anymore, just the middle of the screen works. I can't touch anything that is at the top or bottom of the screen.
Is it posible to solve the issue without replacing it?
Thanks
otaviobonder said:
Hello all,
My Joying HE is starting to lose sensitivity in the touch screen. The bottom and top edges aren't working anymore, just the middle of the screen works. I can't touch anything that is at the top or bottom of the screen.
Is it posible to solve the issue without replacing it?
Thanks
Click to expand...
Click to collapse
What does the reseller suggest if unable to find related solutions here?