Related
YES YOU NEED TO READ THIS WHOLE POST, PROB MORE THEN ONCE TO MAKE SURE YOU GOT IT. YES I KNOW HOW LONG IT IS, I TYPED IT!
*Also note that not all sections will apply to you. I have tried to seperate different senerios using * at each one. Also more then one section here may be needed by you.
the reason i call it a semi-brick is because a true brick can bot be recovered with out opening the case.
first go here and read this for info: http://forum.xda-developers.com/showthread.php?t=838484
now since your here im going to assume that its too late.
*things you will need.
copy of cwm recovery. get it here (the manual install link): http://forum.xda-developers.com/showpost.php?p=9145724&postcount=28
adb installed and working.
a known good rom, or nandroid backup. here is one: http://forum.xda-developers.com/showthread.php?t=836042 (use odex one)
a wpthis.ko for YOUR specfic kernel (run (adb shell cat /proc/version) that will tell you what kernel you have)
*first thing we need to know is, are you s-off or s-on now?
if your s-off just boot into clockwork mod recovery, wipe the phone and flash a known good rom and be done with it. if you dont have cwm recovery installed. boot into fastboot (vol down+power) you must have the sdk/adb installed and working, and type fastboot flash recovery LocationOfRecovery.img (where LocationOfRecovery.img= where you have the recovery, ie c:\android\recovery.img). once thats installed follow instructions above.
*if you are s-on:
will the phone boot into android? if so your not bad off.
if you want to unroot to return the phone, follow the unroot thread here: http://forum.xda-developers.com/showthread.php?t=835971
if you dont want to unroot then you have a couple of different options. if you have cwm recovery still installed, just follow instructions above and flash a known good rom. ive been told that boot.img (kernel) wont flash if you are s-on. the way to fix this (temporarily) is boot into recovery, but before you flash run these commands:
(put wpthis.ko in sdk folder)
adb remount
adb push wpthis.ko /data/local/wpthis.ko (specific for your kernel)
adb shell
# insmod /data/local/wpthis.ko (should get same function not implemented error as when u rooted first time)
then proceed to flash the rom. once booted into android skip down to, "now to get back to s-off"
*if you have stock or eng-recovery installed.
will the phone attempt to boot android at all? where is it stuck at?
a good min after it starts to try to boot, type these commands:
adb remount
adb shell
if you can get in shell then theres still hope. back out shell for a second and start here:
put the cwm recovery.img and wpthis.ko in your sdk folder
adb remount
adb push wpthis.ko /data/local/wpthis.ko (specific for your kernel)
adb push recovery.img /data/local/recovery.img
adb shell
# insmod /data/local/wpthis.ko (should get same function not implemented error as when u rooted first time)
# dd if=/data/local/recovery.img of=/dev/block/mmcblk0p21 (now wait a min or 2 to give it time to finish)
#sync (give it another min or to just to be safe)
#reboot recovery
at this point you should be in cwm recovery. follow instructions above for flashing with s-on.
*if you cannot get into shell while booting, but have eng-recovery installed, there might be some options.(however this is all theory)
boot into recovery-
if you are on linux using adb, you can try taking sh from /system/bin folder of any custom rom, chmod 0755 it, then push it to /system/bin and adb shell might work.
windows-
boot into recovery.
a system.img compatible with your installed kernel pushed may work. put the system.img into the sdk folder.
adb push system.img /data/block/mmcblk0p25
then reboot and see where you are. if that dont work, grab the modified miscnew.img here: http://www.4shared.com/file/pUPfrGi-/mmcblk0p17.html
rename it misc.img put it in sdk folder and
adb push misc.img /dev/block/mmcblk0p17
then reboot into bootloader with PC10IMG.zip on root of sdcard and it should run though. if it does your fully stock and get to start all over again.
*if you cannot get into shell, and you have stock recovery, s-on, and post OTA, im sorry your pretty screwed. as of right now the only thing thats gonna bring it back is a full img/update signed from htc thats equal to or higher then the version currently on the phone. (well and jtag of course)
*well now you've done one of the steps above. your booted into android, you have perm root, and cwm recovery installed, just still s-on. dont worry your almost there!
first take that wpthis.ko for you kernel and push it, and the eng hboot.
adb push wpthis.ko /data/local/
adb push hboot-eng.img /data/local
then from adb shell, or terminal root prompt:
# insmod /data/local/wpthis.ko (again you should get the function not implemented error)
NOW REMEMBER THIS NEXT STEP COULD MEAN DEATH FOR YOU G2 IF TYPED WRONG, AND AFTER ALL THIS HARD WORK!
# dd if=/data/local/hboot-eng.img of=/dev/block/mmcblk0p18
wait a few mins to be sure its done.
# sync
wait a few more just cause.
reboot, you should now be s-off, cwm recovery installed, and free to do whatever you want. just dont go screwing it up again
* as new methods are discovered, or ones here are proven wrong, i will update as necessary. as of the writing post, 2 devices that i know of have been saved!
good luck!
wpthis.ko for bacon bits.03 kernel: http://www.4shared.com/file/OAcd1bix/wpthis-263221-cyanogenmod.html
before you post with problems make sure you have read this at least 2 times. have this info in you post:
what was the last running rom/kernel combo you had?
list EVERYTHING you have done since that point
which recovery is installed?
what happens in recovery when you type
adb devices?
adb remount?
adb shell?
does it try to boot? is it stuck on splash screen, or does it make it to boot animation? 1 min after you turn it on, what happens when you type:
adb devices?
adb remount?
adb shell?
Thank you, really, for taking the time to write this guide. I shared that dreadful feeling of a brick a little while ago, but made it out alive. I know this will help a lot of people.
I'm not bricked, semi bricked or none of that. Rootrd and running BB 0.3
This is the best guide to everything you would need. Too bad you can't post this at the beginning of every thread or some kind of link on every page. This would answer a lot of question if some people would look hard enough. I'm not some smart phone guy by no means. I just read a lot before I ask. In my further reading I can direct people.with further problems here.
Thanks for all your work and giving me another fun hobby
Peace
Sent from my T-Mobile G2 using XDA App
Question why is it that you have "dd if....../mmcblk0p21" in one area and towards the bottom you have "May brick phone ...dd if...../mmcblk0p18." Thought it should always be .../mmcblk0p18?
Phone: T-Mobile G2/Vision Rooted
Rom: Latest Cyanogen
Recovery: CWM waiting for Amon_RA
Good point . Not sure on that one
Sent from my T-Mobile G2 using XDA App
renn9420 said:
Question why is it that you have "dd if....../mmcblk0p21" in one area and towards the bottom you have "May brick phone ...dd if...../mmcblk0p18." Thought it should always be .../mmcblk0p18?
Phone: T-Mobile G2/Vision Rooted
Rom: Latest Cyanogen
Recovery: CWM waiting for Amon_RA
Click to expand...
Click to collapse
if you look where im saying /mmcblk0p21 we are replacing RECOVERY with CWM. i do that because i just dont like the idea of trying to replace hboot from a looping system. worst case something goes wrong, you still have hboot and you can try again. screw up hboot, game over! then once android is back up and running we worry about hboot on mmcblk0p18.
you should not state that steps can be changed if people are brave, someone is going to sip parts and cry that their hboot is boned and now they have a BRICK, this is the best post i have seen in the G2 section thus far and i have been through almost every thread(with any kind of importance) in the dev section and 90% of them in general and Q&A. thank you for this post and let's hope people READ at least 5 times before even starting on this.
Gotcha
Phone: T-Mobile G2/Vision Rooted
Rom: Latest Cyanogen
Recovery: CWM waiting for Amon_RA
Amazing guide, thanks a lot.
fastludeh22 said:
the reason i call it a semi-brick is because a true brick can bot be recovered with out opening the case.
Click to expand...
Click to collapse
I have a full, honest-to-god brick in my drawer (executed dd if=/sdcard/hbooteng.img of=/dev/block/mmcblk0p18 with a wrong "hbooteng.img file).
I'm really, really interested in some guide or info about how to try and recover the brick. I don't mind if I have to open the case, there's not going down from where I am right now.
By the way, my second DZ just arrived, tomorrow I'll try to S-OFF it again... I will have nightmares tonight.
reycat said:
Amazing guide, thanks a lot.
I have a full, honest-to-god brick in my drawer (executed dd if=/sdcard/hbooteng.img of=/dev/block/mmcblk0p18 with a wrong "hbooteng.img file).
I'm really, really interested in some guide or info about how to try and recover the brick. I don't mind if I have to open the case, there's not going down from where I am right now.
By the way, my second DZ just arrived, tomorrow I'll try to S-OFF it again... I will have nightmares tonight.
Click to expand...
Click to collapse
Well it will take a jtag and a lot of research, since it hasn't been done to a g2 yet. Search g1 development forum dor debricking if u want an idea of what's involved.
I remember talking to gtrab a little about your problem. So did you use the wrong file, or did you type an address wrong? What file or typo was it exactly?
What happens when u try to boot into fastboot, or anything else?
{golf clap} on the post.
you sir, have incredible patience... and it's truly appreciated.
fastludeh22 said:
Well it will take a jtag and a lot of research, since it hasn't been done to a g2 yet. Search g1 development forum dor debricking if u want an idea of what's involved.
Click to expand...
Click to collapse
Mmm... It seems all of it is quite a bit over my head.
I remember talking to gtrab a little about your problem. So did you use the wrong file, or did you type an address wrong? What file or typo was it exactly?
What happens when u try to boot into fastboot, or anything else?
Click to expand...
Click to collapse
Don't ask me how I did it, but I actually downloaded a web page instead of the actual hboot file I should have used . I did it from the phone and didn't notice. Since I was supposed to rename it to make the typing easier, I didn't notice it was the wrong file.
Anyway, right now the phone is a complete brick. It doesn't respond to any button presses, the LED doesn't do anything when you plug in the charger... A complete brick.
Device offline?
fastludeh22 said:
before you post with problems make sure you have read this at least 2 times. have this info in you post:
what was the last running rom/kernel combo you had?
list EVERYTHING you have done since that point
which recovery is installed?
what happens in recovery when you type
adb devices?
adb remount?
adb shell?
does it try to boot? is it stuck on splash screen, or does it make it to boot animation? 1 min after you turn it on, what happens when you type:
adb devices?
adb remount?
adb shell?
Click to expand...
Click to collapse
Never used ADB before, followed [forum wont let me post outside links] to set it up. when typing adb devices while in recovery mode, get "list of devices attached
HT09PR204734
offline."
here is a screen shot : [forum wont let me post)
running windows 7 64bit...device not recognized by ADB at alll when stuck on splash screen....did some research couldnt find a real solution...soooo what do you recommend trying?
im stuck on the splash screen.. and i cant get adb to work either.. is missing a driver but i cant for the life of me find one ...
-FuRBz- said:
im stuck on the splash screen.. and i cant get adb to work either.. is missing a driver but i cant for the life of me find one ...
Click to expand...
Click to collapse
Download and instal PDANet, that gave me the drivers i needed for adb, now if only i could figure out how to get my device to register online through the ADB command interface.....
^^ you my friend are awesome! dl pdanet, was able to get the drivers.. was able to go into bootloader and did a recovery from there.. im up and running again!!
marley097 said:
Never used ADB before, followed [forum wont let me post outside links] to set it up. when typing adb devices while in recovery mode, get "list of devices attached
HT09PR204734
offline."
here is a screen shot : [forum wont let me post)
running windows 7 64bit...device not recognized by ADB at alll when stuck on splash screen....did some research couldnt find a real solution...soooo what do you recommend trying?
Click to expand...
Click to collapse
Sounds like you have stock recovery installed, with s-on and no adb/shell access, I'm sorry your pretty screwed. You can try factory reset and see if that helps boot, or to get adb access while trying to boot. Other then that, at the moment the only way to recover is a offical signed pc10img of version equal to or higher then what you have. I'm working hard to come up with something, ill keep you guys informed. I think u said in pm, you have already done the OTA, which makes you version number 1.22.something.
-FuRBz- said:
^^ you my friend are awesome! dl pdanet, was able to get the drivers.. was able to go into bootloader and did a recovery from there.. im up and running again!!
Click to expand...
Click to collapse
Glad you got it! After drivers installed, did you fix it per a section of the op?
it all happened because i had tried flashing cm 6.1- it got stuck on the splash screen but i had done a recovery prior to trying to flash... once i got the drivers installed i was able to get in to adb and do a reboot-bootloader and was able to get into the recovery file
fastludeh22 said:
Sounds like you have stock recovery installed, with s-on and no adb/shell access, I'm sorry your pretty screwed. You can try factory reset and see if that helps boot, or to get adb access while trying to boot. Other then that, at the moment the only way to recover is a offical signed pc10img of version equal to or higher then what you have. I'm working hard to come up with something, ill keep you guys informed. I think u said in pm, you have already done the OTA, which makes you version number 1.22.something.
Click to expand...
Click to collapse
Lame....so how often do they release official pic10img's....? are we talkin a month....or a year?
Hello all,
I've had a DZ for nearly 2 weeks now, and have been holding off on installing roms, overclocking etc until there were clear, reversible guidlines available.
A few days ago I was being curious and ended up doing this the UBERROOT guide.
Essentially I temprooted using Visionary then executed the gfree script on my PC:
adb push gfree /data/local
adb shell
su
cd /data/local
chmod 777 gfree
./gfree
sync
This went well, and when I got to the bootloader I could see indeed that my S was OFF.
However, before I go any further I want to know how to reverse what I've done. This is mentioned at the bottom of the UBERROOT guide:
'run gfree, which will create a new backup of partition 7 in its unlocked state.
this will disable wp on the emmc, as well as remove the brq filter from the kernel.
at this point, you can dd if=/wherever/your/partition7-relock.img of=/dev/block/mmcblk0p7
sync; reboot'
I found the backup, although it was a .bin file not .img
I entered in the command above, but my phone rebooted before I could enter the 'sync' command. My S is still off, it would seem.
So my question to you fine people, having typed all this is:
How can I use the gfree backup to return my phone back to stock?
nofixio said:
How can I use the gfree backup to return my phone back to stock?
Click to expand...
Click to collapse
You can use the "dd" command to copy back the image of that original partition, as you mention.
However, the latest version of gfree now includes some new options to un-do that stuff, e.g. you can switch S-ON back on and change your SID via options. See the Wiki on this - http://forum.xda-developers.com/wik...Phone.2C_Set_SuperCID.2C_and_Turn_Radio_S-OFF
nofixio said:
Hello all,
I've had a DZ for nearly 2 weeks now, and have been holding off on installing roms, overclocking etc until there were clear, reversible guidlines available.
A few days ago I was being curious and ended up doing this the UBERROOT guide.
Essentially I temprooted using Visionary then executed the gfree script on my PC:
adb push gfree /data/local
adb shell
su
cd /data/local
chmod 777 gfree
./gfree
sync
This went well, and when I got to the bootloader I could see indeed that my S was OFF.
However, before I go any further I want to know how to reverse what I've done. This is mentioned at the bottom of the UBERROOT guide:
'run gfree, which will create a new backup of partition 7 in its unlocked state.
this will disable wp on the emmc, as well as remove the brq filter from the kernel.
at this point, you can dd if=/wherever/your/partition7-relock.img of=/dev/block/mmcblk0p7
sync; reboot'
I found the backup, although it was a .bin file not .img
I entered in the command above, but my phone rebooted before I could enter the 'sync' command. My S is still off, it would seem.
So my question to you fine people, having typed all this is:
How can I use the gfree backup to return my phone back to stock?
Click to expand...
Click to collapse
When you run gfree, it creates a bin file in your sd card. That bin file you shall rename it to "whatever".img, to be more specific rename it to partiiton7-relock.img.
Now once you did this, just run gfree again:
adb push gfree /data/local
adb shell
su
cd /data/local
chmod 777 gfree
./gfree
sync
Once done the above, just download terminal emulator and from there run:
su
dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7
sync
exit
And reebot the phone, Now you can go and see you are S-ON.
This method above works without a problem as myself have tried several times, however as steviewevie mentioned, the new version of gfree does this easier.
buzmay said:
When you run gfree, it creates a bin file in your sd card. That bin file you shall rename it to "whatever".img, to be more specific rename it to partiiton7-relock.img.
Now once you did this, just run gfree again:
adb push gfree /data/local
adb shell
su
cd /data/local
chmod 777 gfree
./gfree
sync
Once done the above, just download terminal emulator and from there run:
su
dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7
sync
exit
And reebot the phone, Now you can go and see you are S-ON.
This method above works without a problem as myself have tried several times, however as steviewevie mentioned, the new version of gfree does this easier.
Click to expand...
Click to collapse
How to get that file (partition7-relock.img)? Because I formated the card after g-free method and I runned the official Ruu, so now I have that stupid S-Off, I need it S-On...
Niiceg said:
How to get that file (partition7-relock.img)? Because I formated the card after g-free method and I runned the official Ruu, so now I have that stupid S-Off, I need it S-On...
Click to expand...
Click to collapse
You don't need the backup for that. Just check the Wiki to find the options for gfree that will set it back to S-ON
Sent from my HTC Desire Z
steviewevie said:
You don't need the backup for that. Just check the Wiki to find the options for gfree that will set it back to S-ON
Sent from my HTC Desire Z
Click to expand...
Click to collapse
I don't find anything more than this guide:
Turning S-On
If you are returning your Vision to stock, you will want to flash your stock ROM and Recovery image before starting this, as root permissions and S-Off are required for both of those processes.
Remove Gfree (turn back S-On):
When you first ran Gfree, it automatically backed up your stock partition 7 (with S-On) and placed it on your microSD card as a file named part7-(something).bin and you will need to rename this file to: partition7-relock.img
Open up your ADB command prompt on your computer (with your phone plugged in) and type the following exactly as shown:
Code:
adb shell
su
cd /data/local
chmod 777 gfree
./gfree
dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7
sync
reboot bootloader
Your phone will reboot into bootloader. Look at the first line. The end should now say "S-On".
steviewevie said:
You don't need the backup for that. Just check the Wiki to find the options for gfree that will set it back to S-ON
Sent from my HTC Desire Z
Click to expand...
Click to collapse
I think they removed the automatic option for some reason, I beleive it was in version v.3 and now v.2 is back up. I was looking for that option for someone else early yesterday and noticed its not on the Wiki anymore, unless I missed it, but Im prettty sure I didn't. So I think were back to using the "dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7" command.
Update: On fattire's thread they said they took down v3 because people were having problems with it and are now advising using v2 and the old restore method.
joemm said:
I think they removed the automatic option for some reason, I beleive it was in version v.3 and now v.2 is back up. I was looking for that option for someone else early yesterday and noticed its not on the Wiki anymore, unless I missed it, but Im prettty sure I didn't. So I think were back to using the "dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7" command.
Click to expand...
Click to collapse
Where to get that file if i already formated the card?!
Niiceg said:
Where to get that file if i already formated the card?!
Click to expand...
Click to collapse
There is no where to get the file if you erased/formatted your sdcard without saving it somewhere else, the instructons on gfree tell you to do this:
"gfree created a backup of your original partition 7 at /sdcard/part7backup-<time>.bin you might consider copying this to a safe location on your computer."
So if you didnt do this I really dont know what you can do. I have my part7backup but I dont know if its specific to my device or if anyone can use it.
joemm said:
There is no where to get the file if you erased/formatted your sdcard without saving it somewhere else, the instructons on gfree tell you to do this:
"gfree created a backup of your original partition 7 at /sdcard/part7backup-<time>.bin you might consider copying this to a safe location on your computer."
So if you didnt do this I really dont know what you can do. I have my part7backup but I dont know if its specific to my device or if anyone can use it.
Click to expand...
Click to collapse
Well, What device you have? Z or G2? I think that it's not specific, because all phones are the same ;D
Niiceg said:
I don't find anything more than this guide:
Turning S-On
Click to expand...
Click to collapse
Look at http://forum.xda-developers.com/wik...Phone.2C_Set_SuperCID.2C_and_Turn_Radio_S-OFF
Scroll down to the bit that shows you the usage message for gfree and check out the "-s" option
joemm said:
I think they removed the automatic option for some reason, I beleive it was in version v.3 and now v.2 is back up. I was looking for that option for someone else early yesterday and noticed its not on the Wiki anymore, unless I missed it, but Im prettty sure I didn't. So I think were back to using the "dd if=/sdcard/partition7-relock.img of=/dev/block/mmcblk0p7" command.
Update: On fattire's thread they said they took down v3 because people were having problems with it and are now advising using v2 and the old restore method.
Click to expand...
Click to collapse
The latest gfree 0.03 had problems, yes, so they went back to 0.02 in the Wiki. But as my previous post shows, you can still un-do things with gfree 0.02.
The only reason to use the backup of partition 7 that I can think of is if you don't know what your original CID was to reset to, or if you want to SIM Lock your phone again (there doesn't seem to be an undo option for the SIM Unlock).
steviewevie said:
The latest gfree 0.03 had problems, yes, so they went back to 0.02 in the Wiki. But as my previous post shows, you can still un-do things with gfree 0.02.
The only reason to use the backup of partition 7 that I can think of is if you don't know what your original CID was to reset to, or if you want to SIM Lock your phone again (there doesn't seem to be an undo option for the SIM Unlock).
Click to expand...
Click to collapse
Ok, I see the option for sec-flag on/off but does that also restore the sim lock?
Sent from my T-Mobile G2 using XDA App
joemm said:
Ok, I see the option for sec-flag on/off but does that also restore the sim lock?
Click to expand...
Click to collapse
No it doesn't as far as I know, but that's why I said restoring SIM lock was the only real use for that part7 backup that I could think of.
steviewevie said:
No it doesn't as far as I know, but that's why I said restoring SIM lock was the only real use for that part7 backup that I could think of.
Click to expand...
Click to collapse
I wasn't sure myself, thanks.
Sent from my T-Mobile G2 using XDA App
steviewevie said:
No it doesn't as far as I know, but that's why I said restoring SIM lock was the only real use for that part7 backup that I could think of.
Click to expand...
Click to collapse
Okey, can you tell how to do everything? Because I don't know anything with that gfree... And there is no instruction... Please, help me get the S-On
I have PM'd the author of gfree about an option for SIM re-lock, because that would be useful. I guess you will still need some sort of carrier string which it needs re-locking to though ? Would be handy if perhaps gfree told you what that was before you unlocked it.
Im in the same boat as niiceg, I cannot find my backup and have had no luck in my searchs. Any Idea's what I can do from here?
Thanks in advance..
ps I'm guess my next step is to re root and do
su
cd /data/local
chmod 777 gfree
./gfree -s on
sync
???
bildo said:
Im in the same boat as niiceg, I cannot find my backup and have had no luck in my searchs. Any Idea's what I can do from here?
Thanks in advance..
ps I'm guess my next step is to re root and do
su
cd /data/local
chmod 777 gfree
./gfree -s on
sync
Click to expand...
Click to collapse
Yes, you just need to run "gfree -s on" as root to go from radio S-OFF to S-ON, no need to find/restore that backup.
My HTC Desire has no USB functionality at all, including USB Fastboot. It's also got no root access. There's no known reason why this occured.
Similar forum threads suggest that USB functions can be restored if I revert to the stock RUU image. It's possible that an update has been the cause of this problem.
I've tried to install the base ROM - RUU, but because I have Hboot 0.93 I have to downgrade, but can't do that because there is no existing root access and I don't have ClockWorksMod recovery installed to get around the signature verifications.
The device boots up and operates fine (even the SD Card). I have to charge the battery using my partner's phone and can't do any data transfers. I'm running Android 2.2, Radio 32.49.00.32U_5.11.05.27, Hboot 0.93
I'm beginning to think that the motherboard has somehow been fried and can no longer supprt the USB part of it.
Any ideas would be most helpful. Thanks heaps
As you are unrooted, you should have warranty and that is the first way to fix it.
The other is a bit more complicated but if you are cautions, you'll be fine. Use this guide:
quanchi said:
...
This is a specific situation - usb brick and totally stock rom, recovery and hboot. It's not required for people who have a modified recovery and a rooted rom. It's easy like 1-2-3.
Before doing anything else enable the Debug Mode in the Applications / Dev menu
1. Download the rageagainstthecage exploit from the authors site:
http://c-skills.blogspot.com/2010/08/please-hold-line.html
2. Download the flash_image and misc (mtd0.img) partition image from this thread.
http://forum.xda-developers.com/showthread.php?t=691639&highlight=usb+brick
Modify the mtd0.img according to your phones CID (how to get the CID also explained in the thread)
2. Download Android Terminal Emulator from the Market
3. Copy the exploit binary (rageagainstthecage-arm5.bin), the flash_image and modifed mtd0.img to the sdcard via an external card reader
4. Start the Terminal
5. Copy the files to the Terminal app data directory (the only place on the data partition you will have write access while running the Terminal), and make the binaries executable
Code:
cat /sdcard/rageagainstthecage-arm5.bin > /data/data/jackpal.androidterm/shared_prefs/rageagainstthecage-arm5.bin
cat /sdcard/flash_image > /data/data/jackpal.androidterm/shared_prefs/flash_image
cat /sdcard/mtd0.img > /data/data/jackpal.androidterm/shared_prefs/mtd0.img
cd /data/data/jackpal.androidterm/shared_prefs/
chmod 755 rageagainstthecage-arm5.bin flash_image
6. Run the exploit
Code:
/data/data/jackpal.androidterm/shared_prefs/rageagainstthecage-arm5.bin
After the exploit exits/finishes there should be a short system freeze, followed by inablity to issue any command from the terminal (don't worry). Exit the Terminal by long pressing HOME and force close the Terminal app from the Application Manager
7. Start the terminal again, a root prompt should be visible
8. Flash the misc partition
Code:
cd /data/data/jackpal.androidterm/shared_prefs
./flash_image misc mtd0.img
9. Reboot
...
Click to expand...
Click to collapse
No luck unfortunately, one of the steps requires the CID, and as you know I have not got USB to access fastboot mode.
Is there any other way to get the CID?
You should read the whole thread for the usb-fix
If I remember correctly you should use "cat /sys/class/mmc_host/mmc1/mmc1:*/cid" (without quotes) command from the terminal emulator.
The terminal emulator in your case will be the substitute for the fastboot, so everything is done via the former.
If you click the link to the quote, you'll see that there are number of people who got it sorted using this method. So just be patient and do the reading.
Ive got same problem, but have fastboot access.. Can I use regular terminal in windows then?
Well, you can use it to find the CID ("fastboot oem boot"), but the other commands in the guide quoted above are for a terminal emulator and are not the same as the ones used with fastboot. So in order not to get confused I recommend you to just use a terminal emulator, it's not harder than fastboot.
Well, i figured out that one on my own.. At least I learn something of this.. Anyway, when i try to execute first command in emulator I just get up "cannot create, directory nonexistent. Ive tripple checked the commandlines.. What could be wrong??
bump.........
Well I followed all the instructions, could get temp root access and flash a modified mtd0.img (which had the correct CID and Rom version) but still no USB. I tried it several times over and can't get anywhere. The hardware must be cactus! Time to throw it over a cliff !!
I run the following commands
su
adb shell
daemon not running, starting it now on port 5038
daemon started successfully
error: device not found.
any suggestions?
Replug usb cable after adb daemon start on PC or try to get adb when phone in CWM...
scott0 said:
I run the following commands
su
adb shell
daemon not running, starting it now on port 5038
daemon started successfully
error: device not found.
any suggestions?
Click to expand...
Click to collapse
Er... you're running adb _inside_ the phone?
aremcee said:
Er... you're running adb _inside_ the phone?
Click to expand...
Click to collapse
i'm guessing that's the issue.
scott0 said:
i'm guessing that's the issue.
Click to expand...
Click to collapse
ADB is used to connect to android devices. So unless you have another android plugged to your P930, running adb on the phone is pointless
hey thanks.
i guess i am way off track, i want to restore the phone's original recovery image (at some point in the future) and am tired of dealing with adb/windows on my PCs.
i was under the impression this could be done via terminal emulator/adb.
scott0 said:
hey thanks.
i guess i am way off track, i want to restore the phone's original recovery image (at some point in the future) and am tired of dealing with adb/windows on my PCs.
i was under the impression this could be done via terminal emulator/adb.
Click to expand...
Click to collapse
Well... yes, you need adb to connect to the phone, but terminal emulator is already running on the phone.
i see, well, i was hoping to be able to temporarily go back to the stock recovery to do OTA updates and such, it appears it won't be as cut&dry as i was hoping. i assumed that since adb is installed and running on the device via terminal emulator that it could be used to push/pull the stock recovery image onto the phone.
scott0 said:
i see, well, i was hoping to be able to temporarily go back to the stock recovery to do OTA updates and such, it appears it won't be as cut&dry as i was hoping. i assumed that since adb is installed and running on the device via terminal emulator that it could be used to push/pull the stock recovery image onto the phone.
Click to expand...
Click to collapse
You're still not getting it: The only purpose of "adb shell" is to connect you to the phone; terminal emulator is a direct shell already on the phone.
i simply want to flash the original recovery image to the phone without using a PC.
it was my understanding that this is possible via terminal emulator, does anyone know if this is possible and if so, could you point me in the right direction to learn how to do that?
thanks!
scott0 said:
i simply want to flash the original recovery image to the phone without using a PC.
it was my understanding that this is possible via terminal emulator, does anyone know if this is possible and if so, could you point me in the right direction to learn how to do that?
thanks!
Click to expand...
Click to collapse
Just use Terminal emulator in your phone and add manually the following commands to flash original images (put them on sd-card before):
Code:
su
dd if=/sdcard/boot.img of=/dev/block/mmcblk0p8
dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p13
dd if=/sdcard/firmware.img of=/dev/block/mmcblk0p1
dd if=/sdcard/baseband.img of=/dev/block/mmcblk0p14
dd if=/sdcard/system.img of=/dev/block/mmcblk0p27
super, thank you Machzelet!
i will give that a whirl this weekend.
here's how i think it will go
images to sd card
restore backed up original rom va rom manager
open up terminal emulator, run the commands above
reboot
update with OTA update
easy breezy?
Why would you even bother updating? The changes in the OTA update will eventually appear in custom ROMs anyway.
do i rly need to provide a reason for wanting to fiddle around with my phone? on a dev board? lolz
I created the pathways needed to open files in command prompt and set the pathways to C:\Android-sdk\tools and C:\Android-sdk\platform-tools. I have unzipped and installed everything and placed the files in the platform-tools folder, but i cannot access the files through prompt. it tells me C:\android-sdk\platform-tools is not recognized as and internal or external command. Please someone help... i havent worked with DOS since i was in high school 14+yrs ago.
So you changed your PATH environment variable to include 'C:\Android-sdk\tools' and platform-tools?
That just lets cmd run exe's from those folders regardless of where it is pointed, it will not let you access other files from those folders.
You still need to either change where cmd is pointed (using the 'cd' command) or you can move the files to where cmd is currently pointed (probably C:\Users\Username>')
-Nipqer
Still need some assistance, when starting to downgrade from gingerbread its telling me that i dont have a device detected. I have USB debugging on, so i dont know what i should do; any ideas
PvtJoker said:
Still need some assistance, when starting to downgrade from gingerbread its telling me that i dont have a device detected. I have USB debugging on, so i dont know what i should do; any ideas
Click to expand...
Click to collapse
Hello noob.
Did you install the USB drivers ( HTC Sync software )?
shared_ptr said:
Hello noob.
Did you install the USB drivers ( HTC Sync software )?
Click to expand...
Click to collapse
Im not sure if i installed the USB drivers. I installed everything that the wiki guide said to. I am gonna try again once i get home.
PvtJoker said:
Im not sure if i installed the USB drivers. I installed everything that the wiki guide said to. I am gonna try again once i get home.
Click to expand...
Click to collapse
I faced the same problem. My Windows PC didn't recognize the attached Android-device (Check Windows Device Manager).
After following the instructions as described in the following thread it suddenly worked and I could successfully root my device:
[Tutorial] Adb Driver Android 1.0 Install
Cheers
pemphix
Please help
Well i got the USB driver installed and ran adb Devices.... it picked up my phone but now when im running adb push fre3vo /data/local/tmp i get the message "cannot stat "fre3vo" no such file or directory". Am i suppose to be in C:\users\name\Android-sdk\platform-tools\ to run the adb push?
If so, need some help with command prompt. Im running windows 7,
need to either edit the path in environmental variables or make sure all the files needed and adb.exe are in the same folder and change directories to there, i have a guide to setup fastboot (and adb is the same setup for the most part) HERE
Ok, Well i got Command prompt to start working. i remembered how to path in dos but my first go round with commands didnt work so i have to try another line to exploit.. wish me luck:fingers-crossed:
I will keep that in mind.. right now im trying to get the exploit to work.. i have gone through 1 thru 3 and got nothing yet...
so you successfully downgraded to 2.2 and are now trying to temp root? maybe like the guide you are using so we know what steps 1 through 3 are and explain what isnt working if you have issues
xda wiki, cyanogen wiki and strawmetals pdf guide are simple easy and trust worthy. i hope one of these is the guide you are using
In process of downgrading
demkantor said:
so you successfully downgraded to 2.2 and are now trying to temp root? maybe like the guide you are using so we know what steps 1 through 3 are and explain what isnt working if you have issues
xda wiki, cyanogen wiki and strawmetals pdf guide are simple easy and trust worthy. i hope one of these is the guide you are using
Click to expand...
Click to collapse
I have gotten as far as "# dd if=/dev/block/mmcblk0p17 bs=1 skip=160 count=10 1.00.000.010+0 records in 10+0 records out 10 bytes transferred in 0.001 secs (10000 bytes/sec)". Now the next step is to downgrade. the command line is:
> adb push su /data/local/tmp/
> adb push busybox /data/local/tmp/
> adb push fixsu.sh /data/local/tmp/
> adb install SuperUser.apk
> adb shell chmod 755 /data/local/tmp/fixsu.sh
> adb shell /data/local/tmp/fixsu.sh
but my command prompt is still # what do i do to
skip that, thats just for temp root which is pretty unnecessary. just downgrade and move on
I know i sound really stupid, but where is the Root of my SD card??? Please dont tell me its just the card itself...
yup, dont put files in a folder is what that means
Ok, now im in Hboot, but i dont understand what im suppose to do next. How do i work bootloader to downgrade. Once in bootloader i see; fastboot, recovery, factory reset, simlock and image crc
if the PC10IMG.zip is on the root of sd card and is named properly it will do it for you, just boot into hboot and let it do its thing.
if you want to do it the fastboot way (my preference but both work fine) then follow setherios guide to do it that way
---------- Post added at 05:01 PM ---------- Previous post was at 05:00 PM ----------
oh and always check md5sums when flashing firmware, its a good habit to have
Now here is an important question. If i had to turn off my phone before the Hboot took, do i have to go thru the entire process again? or can i just do the reboot bootloader?
well i just tried to fastboot flash zip StockRom.zip and it said cannot load StockRom.zip any ideas how to get it to work??
are you using window? if so know that it may be hiding the file extentions, so pc10img.zip should be named pc10img
etc, this may be your issue other than that you will have to copy and paste your issues so I can see what you are doing and why its failing
Sent from my HTC Vision using xda premium