Unlocked bootloader ,all OK. (via official LG unlock.bin )
Installed TWRP, all OK. Installed STOCK-20a-ROOTED.zip for the LG G4, by cile381 all OK-- but no ROOT.
So I tried STOCK-20a-ROOTED.zip again but this time went with the SU option, and bootloop, loop, loop------------
I did a backup with TWRP before any of this happened ,BUT even though backup is present -- something is read only, I presume it's the system disk.
Would like a bit of help as phone is spanking new and has never left the house or even had my SIM card in it.
Phone get the red swipe over and then the LG Logo comes on and stays looping at that point.
tnx and hope it's not good night
dohouch said:
Unlocked bootloader ,all OK. (via official LG unlock.bin )
Installed TWRP, all OK. Installed STOCK-20a-ROOTED.zip for the LG G4, by cile381 all OK-- but no ROOT.
So I tried STOCK-20a-ROOTED.zip again but this time went with the SU option, and bootloop, loop, loop------------
I did a backup with TWRP before any of this happened ,BUT even though backup is present -- something is read only, I presume it's the system disk.
Would like a bit of help as phone is spanking new and has never left the house or even had my SIM card in it.
Phone get the red swipe over and then the LG Logo comes on and stays looping at that point.
tnx and hope it's not good night
Click to expand...
Click to collapse
Try to get into download mode. If you don't know how just check this thread. Once done use LGUP to flash the 6.0 kdz (if you want a stock 6.0 ROM), or flash 5.1 KDZ for your device and restore root and TWRP. LGUP thread is located here. Just follow the instructions.
Please keep in mind that there's a way to get out of bootloops 99% of the time (In fact 100% if it's a software problem). Furthermore, if you'd like to have a rooted 6.0 ROM, refurbish to 5.1 and follow these instructions. Hit thanks if this helped
Big thanks to " Follow_and_Feel"
I'm up and running again, now how do root this marshy_mallow. Have a few threads will have to spend more time going through them
dohouch said:
Big thanks to " Follow_and_Feel"
I'm up and running again, now how do root this marshy_mallow. Have a few threads will have to spend more time going through them
Click to expand...
Click to collapse
As I said. Just refurbish with LGUP to 5.1 (if you're not on 5.1 already) and then root it with this method, flash TWRP (You'll find a lot of threads how to do it) and then follow these instructions and you're on rooted 6.0
Please note that there's no official way to get xposed to H815, since the latest zip is leading to bootloops (If you're interested in further modding). Cheerio my friend Hit thanks if I was of help
Follow_and_Feel said:
Try to get into download mode. If you don't know how just check this thread. Once done use LGUP to flash the 6.0 kdz (if you want a stock 6.0 ROM), or flash 5.1 KDZ for your device and restore root and TWRP. LGUP thread is located here. Just follow the instructions.
Please keep in mind that there's a way to get out of bootloops 99% of the time (In fact 100% if it's a software problem). Furthermore, if you'd like to have a rooted 6.0 ROM, refurbish to 5.1 and follow these instructions. Hit thanks if this helped
Click to expand...
Click to collapse
It says unknown device :/
any help?
-gloim- said:
It says unknown device :/
any help?
Click to expand...
Click to collapse
What's your problem and what have you tried/done already? I need a little more information (e.g. Device Model, ROM, OS, etc.)
Follow_and_Feel said:
What's your problem and what have you tried/done already? I need a little more information (e.g. Device Model, ROM, OS, etc.)
Click to expand...
Click to collapse
- LG H815
- Android 6.0 Stock Rom with unlocked bootlader, root and twrp
- the bootloop is caused by a change in the build.prop
I already tryed the lg flashtool 2014, lg bridge(it said that there are no problems), lg up (unknown device), adb (no adb connection).
Is there a way to boot into twrp with the hardware keys?
-gloim- said:
- LG H815
- Android 6.0 Stock Rom with unlocked bootlader, root and twrp
- the bootloop is caused by a change in the build.prop
I already tryed the lg flashtool 2014, lg bridge(it said that there are no problems), lg up (unknown device), adb (no adb connection).
Is there a way to boot into twrp with the hardware keys?
Click to expand...
Click to collapse
Yes of course there is!
Power off your device (E.g. pull battery), wait until it's completely shut down, now
Hold power button AND Volume Down button
Hold these two buttons until you see the LG logo on your screen
If the logo appears, immediately release ONLY the power button for 1 sec (you're still holding the Volume down button)
Now press and hold power button again (still holding volume down button)
If it now asks you to wipe your system, click "yes" and "yes" and tada...you're in TWRP
Follow_and_Feel said:
Yes of course there is!
Power off your device (E.g. pull battery), wait until it's completely shut down, now
Hold power button AND Volume Down button
Hold these two buttons until you see the LG logo on your screen
If the logo appears, immediately release ONLY the power button for 1 sec (you're still holding the Volume down button)
Now press and hold power button again (still holding volume down button)
If it now asks you to wipe your system, click "yes" and "yes" and tada...you're in TWRP
Click to expand...
Click to collapse
I already tryed this
after reseting my g4 there is no twrp it only botts into the bootloop
-gloim- said:
I already tryed this
after reseting my g4 there is no twrp it only botts into the bootloop
Click to expand...
Click to collapse
Well that's f*cked up. Mhhh. Did you try to get into download mode, like I posted above? That didn't work neither?
Follow_and_Feel said:
Well that's f*cked up. Mhhh. Did you try to get into download mode, like I posted above? That didn't work neither?
Click to expand...
Click to collapse
the download mode works, but lg up says unknown device
-gloim- said:
the download mode works, but lg up says unknown device
Click to expand...
Click to collapse
And LG Flash Tool doesn't recognize your Phone in download mode?
Follow_and_Feel said:
And LG Flash Tool doesn't recognize your Phone in download mode?
Click to expand...
Click to collapse
this is the error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
-gloim- said:
this is the error:
Click to expand...
Click to collapse
I can't see the picture. Could you upload it on xup.in for example?
EDIT: Or dropbox?
Follow_and_Feel said:
I can't see the picture. Could you upload it on xup.in for example?
EDIT: Or dropbox?
Click to expand...
Click to collapse
here it is
[/url][/IMG]
-gloim- said:
here it is
[/url][/IMG]
Click to expand...
Click to collapse
Ok. I suggest you re-install LG Flash Tool, re-install drivers and make sure you're using a proper USB-cable. Try it again and then let me know.
Additionally, did you try a CSE flash? I don't know what's the problem, but it actually should recognize your phone, if it's in download mode. Are you sure you're in dl mode?
Follow_and_Feel said:
Ok. I suggest you re-install LG Flash Tool, re-install drivers and make sure you're using a proper USB-cable. Try it again and then let me know.
Additionally, did you try a CSE flash? I don't know what's the problem, but it actually should recognize your phone, if it's in download mode. Are you sure you're in dl mode?
Click to expand...
Click to collapse
It's in download mode and I read that the lg flash tool don't work with Android M.
Edit: I also tryed CSE flash
-gloim- said:
It's in download mode and I read that the lg flash tool don't work with Android M.
Click to expand...
Click to collapse
Ah yeah forgot about that. Well that's quite difficult. What happens if you use LGUP?
Could you send me a screenshot too?
Follow_and_Feel said:
Ah yeah forgot about that. Well that's quite difficult. What happens if you use LGUP?
Could you send me a screenshot too?
Click to expand...
Click to collapse
I didn't find a solution to fix that within bootloop
---------- Post added at 06:17 PM ---------- Previous post was at 05:56 PM ----------
Not necessary, in bootloop, just connect usb and start lgup, when it detect it, (and it will as unknown mode device) tap com port it was found on and ui will open, then click on phone info, it will connect and establish a valid usb connection to phone and open new prompt with phone info...... Then start adb command prompt and enter 'adb reboot recovery' and bingo you're in recovery.... Solves every bootloop!
Click to expand...
Click to collapse
Did you know what he mean with "tap com port"?
-gloim- said:
I didn't find a solution to fix that within bootloop
---------- Post added at 06:17 PM ---------- Previous post was at 05:56 PM ----------
Did you know what he mean with "tap com port"?
Click to expand...
Click to collapse
I guess he means that you have to click on the USB Port on your PC, where LGUP detects your phone. There are several things you can do, if LGUP doesn't detect your phone. Just look through this thread. There has to be a solution to this!!
Related
Hi ,,
I have lg g3 D855 i flashed wrong rom for another device so now my device died
i try to flash stock rom but the phone did not enter download mode and the screen is off too and the computer did not detect the G3 .
So any idea or method for how to fix my G3
So v give us a list of all of the functioning and non functioning aspects of this problem
---------- Post added at 08:20 PM ---------- Previous post was at 08:16 PM ----------
Can you power up the phone? Can you get to any recovery with different key combinations? does the phone heat up after being left on or with the battery in? what happened proceeding what rom on did you flash and what are the components of the roms file that would affect vital startup information for the g3
u4icpain said:
So v give us a list of all of the functioning and non functioning aspects of this problem
---------- Post added at 08:20 PM ---------- Previous post was at 08:16 PM ----------
Can you power up the phone? Can you get to any recovery with different key combinations? does the phone heat up after being left on or with the battery in? what happened proceeding what rom on did you flash and what are the components of the roms file that would affect vital startup information for the g3
Click to expand...
Click to collapse
unfortunately the g3 wont start the screen still off ,no recovery or download mode , no heating , the rom i flashed it's specified to galaxy s3 i flashed it by a mistake .
anas_ammar said:
unfortunately the g3 wont start the screen still off ,no recovery or download mode , no heating , the rom i flashed it's specified to galaxy s3 i flashed it by a mistake .
Click to expand...
Click to collapse
Please link us to the rom you flashed so we can know the extent of the damage
itsbighead said:
Please link us to the rom you flashed so we can know the extent of the damage
Click to expand...
Click to collapse
thanks for replay ...
this is the link for the rom i flashed accidentally http://forum.xda-developers.com/galaxy-s3/development/rom-s5-sensation-rom-v3-1-t2759425
when i try do enter download mode the device manager shown new device as the pic
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
so when trying to flash kdz file by lg flash tool its always failed !!!
any suggestion ??
anas_ammar said:
thanks for replay ...
this is the link for the rom i flashed accidentally http://forum.xda-developers.com/galaxy-s3/development/rom-s5-sensation-rom-v3-1-t2759425
when i try do enter download mode the device manager shown new device as the pic
so when trying to flash kdz file by lg flash tool its always failed !!!
any suggestion ??
Click to expand...
Click to collapse
Try this http://forum.xda-developers.com/showthread.php?t=2582142 but im not hopeful that it will work in your circumstance
itsbighead said:
Try this http://forum.xda-developers.com/showthread.php?t=2582142 but im not hopeful that it will work in your circumstance
Click to expand...
Click to collapse
not working
any other suggestions ?
anas_ammar said:
not working
any other suggestions ?
Click to expand...
Click to collapse
Oh man you are in quite a pickle.
Does the phone response when you plug it into a wall charger?
And do you have any sort of warranty ?
MrFishiz said:
Oh man you are in quite a pickle.
Does the phone response when you plug it into a wall charger?
And do you have any sort of warranty ?
Click to expand...
Click to collapse
yes ,,, if the battery empty , when i plug the charger the screen terun on and shown its charging & red light appear from notification led , when i remove the battery and plug the charger the screen turn on and show no battery
unfortunately i have no warranty
anas_ammar said:
not working
any other suggestions ?
Click to expand...
Click to collapse
anas_ammar said:
yes ,,, if the battery empty , when i plug the charger the screen terun on and shown its charging & red light appear from notification led , when i remove the battery and plug the charger the screen turn on and show no battery
unfortunately i have no warranty
Click to expand...
Click to collapse
Tell me if this works for you: http://forum.xda-developers.com/lg-g3/help/solution-flashed-wrong-model-rom-to-d852-t2987242
MrFishiz said:
Tell me if this works for you: http://forum.xda-developers.com/lg-g3/help/solution-flashed-wrong-model-rom-to-d852-t2987242
Click to expand...
Click to collapse
wrong dll " lg flash tool said "
BTW i have TWRP backup for the stock rom ,,, how i can use it in my case ?
anas_ammar said:
wrong dll " lg flash tool said "
BTW i have TWRP backup for the stock rom ,,, how i can use it in my case ?
Click to expand...
Click to collapse
Oh well.. that's excellent.
You have " restore " option in TWRP. try that.
MrFishiz said:
Oh well.. that's excellent.
You have " restore " option in TWRP. try that.
Click to expand...
Click to collapse
i cant coz i cant turn on the g3 !!! its completely dead
MrFishiz said:
Oh well.. that's excellent.
You have " restore " option in TWRP. try that.
Click to expand...
Click to collapse
dude its fully bricked, he cant even get into download mode
I suspect its probably a result of the kernel (boot.img) from the s3 rom which is causing it to brick. If he just wrote a system.img from another phone it would just sit at the lg screen
If he can find a way to wipe the kernel partition then it would probably start. Its because custom roms usually only write stuff to kernel, system and data partitions and nothing else
Did you tried fastboot? Press and hold volume up and plug usb cable like when you want download mode. On PC go to device manager and see if there is Android phone on top of devices and look for the driver for adb interface. You must have Adb installed on PC. If computer recognizes the phone you're good, you can do everything with fastboot commands, flash boot image, twrp... you can even boot boot.img from pc than you can use LG flash tool.
megafan said:
Did you tried fastboot? Press and hold volume up and plug usb cable like when you want download mode. On PC go to device manager and see if there is Android phone on top of devices and look for the driver for adb interface. You must have Adb installed on PC. If computer recognizes the phone you're good, you can do everything with fastboot commands, flash boot image, twrp... you can even boot boot.img from pc than you can use LG flash tool.
Click to expand...
Click to collapse
yes i try to use fastboot the device manager detect my device as
and if i plug the device to pc without pressing any button its detected as
i thing its hopeless case , but i wish if you or any one in xda can figure how to fix it .
anas_ammar said:
yes i try to use fastboot the device manager detect my device as
and if i plug the device to pc without pressing any button its detected as
i thing its hopeless case , but i wish if you or any one in xda can figure how to fix it .
Click to expand...
Click to collapse
On top of the list in device manager should be Android phone, if you don't see it than....
Maybe you can try here if you already didn't :
http://forum.xda-developers.com/showpost.php?p=58699994&postcount=22
Hey all , after more than a month i fixed my g3 i'll write the solution to help all members have the same problem , i wanna to thanks every body who try to help me .
Thanks .
anas_ammar said:
Hey all , after more than a month i fixed my g3 i'll write the solution to help all members have the same problem , i wanna to thanks every body who try to help me .
Thanks .
Click to expand...
Click to collapse
sO. WHat was your solution???
Yeah, tell us what did you do, please !
Hello i bought my Lg G3 d855 international version from USA (amazone).When i come back to my country the phone start to restart 20 time a day.Then on switch off and stuck in Firmware Update.I tried most of the things which i found here,after last 3 month reading.I need a help.Now i can get in only in recovery mode but after i try to do someting i go back to the same Firmware Update.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download and Install "LG Mobile Support Tool" to your PC.
Open the application, then the phone to PC while in Download Mode
Choose "Repair upgrade" from LG Mobile Support Tool.
This will wipe your phone and install latest firmware.
forumber2 said:
Download and Install "LG Mobile Support Tool" to your PC.
Open the application, then the phone to PC while in Download Mode
Choose "Repair upgrade" from LG Mobile Support Tool.
This will wipe your phone and install latest firmware.
Click to expand...
Click to collapse
I dont have access to download mode when i try i get in same Firmware Update 910K B3 QEM.I can get only recovery mode.
bbb83 said:
I dont have access to download mode when i try i get in same Firmware Update 910K B3 QEM.I can get only recovery mode.
Click to expand...
Click to collapse
Firmware Update screen is also Download Mode
forumber2 said:
Firmware Update screen is also Download Mode
Click to expand...
Click to collapse
ok i understood but i cant fine (Choose "Repair upgrade)
http://dl-1.va.us.xda-developers.co....jpg?key=TlyUhAV0vQ_vgyHhmOtgow&ts=1447521406
bbb83 said:
ok i understood but i cant fine (Choose "Repair upgrade)
http://dl-1.va.us.xda-developers.co....jpg?key=TlyUhAV0vQ_vgyHhmOtgow&ts=1447521406
Click to expand...
Click to collapse
If you click "Options" button, you'll see
forumber2 said:
If you click "Options" button, you'll see
Click to expand...
Click to collapse
yes but is not repaire upgrade
is Upgrade recovery and isnt working
stuck on this screen
http://dl-1.va.us.xda-developers.co....jpg?key=yCm0xcAwW1N9CA4VEWaz-A&ts=1447525234
and stay forever on Time elapsed 00.00.18
if i try with flas tool and D85520l_00.kdz
is stuck on 20 % and Upgrade stopped due an error
bbb83 said:
yes but is not repaire upgrade
is Upgrade recovery and isnt working
stuck on this screen
http://dl-1.va.us.xda-developers.co....jpg?key=yCm0xcAwW1N9CA4VEWaz-A&ts=1447525234
and stay forever on Time elapsed 00.00.18
if i try with flas tool and D85520l_00.kdz
is stuck on 20 % and Upgrade stopped due an error
Click to expand...
Click to collapse
im truing to reed phone information and i have got
http://dl-1.va.us.xda-developers.co....png?key=c0roCoGKGqhHcSKsZxBDHQ&ts=1447526021
bbb83 said:
im truing to reed phone information and i have got
http://dl-1.va.us.xda-developers.co....png?key=c0roCoGKGqhHcSKsZxBDHQ&ts=1447526021
Click to expand...
Click to collapse
Flash kdz or tot of lg g3.
As you said you tried to flash kdz & its stopped due to an error, if that error is (Connection to server is failed) just ignore it (don't click on OK). After a minute flashing will start.
Kashif Hashmi said:
Flash kdz or tot of lg g3.
As you said you tried to flash kdz & its stopped due to an error, if that error is (Connection to server is failed) just ignore it (don't click on OK). After a minute flashing will start.
Click to expand...
Click to collapse
always happen this before i post my question i tried almost everything?
http://dl-1.va.us.xda-developers.co....png?key=JcsN579JR5CurOOQPLdJew&ts=1447765006
Step by step-
1.Run LG Flash tool as administrator.
2.Select KDZ file.
3.Click on CSE flash then click on start (Dont click on Read Phone Info. or anything)
4.When phone disconnected error show, enter in downloading mode and then click on retry.
5.After that it show server error ignore it dont click on OK
6.Wait for finshing flash
7.When phone start rebooting remove battery & again put it back then hard reset your phone. Done
If this not work try "tot" method.
Here's the link for both KDZ & tot method- http://forum.xda-developers.com/showthread.php?t=2785089
Kashif Hashmi said:
Step by step-
1.Run LG Flash tool as administrator.
2.Select KDZ file.
3.Click on CSE flash then click on start (Dont click on Read Phone Info. or anything)
4.When phone disconnected error show, enter in downloading mode and then click on retry.
5.After that it show server error ignore it dont click on OK
6.Wait for finshing flash
7.When phone start rebooting remove battery & again put it back then hard reset your phone. Done
If this not work try "tot" method.
Here's the link for both KDZ & tot method- http://forum.xda-developers.com/showthread.php?t=2785089
Click to expand...
Click to collapse
I try that i try and tot metod is looks like download mode is missing i cant go in. And debugging mode is not on.Is there any opportunity to turn it on with ADB. Then on to fix the Data mode and try to do somting?
When i try with tot metod i have got an partition error
http://dl-1.va.us.xda-developers.co....png?key=H9bVx1VJDDkHuEjgmbU3oA&ts=1447856715
Post your question here http://forum.xda-developers.com/showthread.php?t=2785089
no solution for me
I've got this exact problem... Can't understand why there isn't a fix as yet..
DarkStar22 said:
I've got this exact problem... Can't understand why there isn't a fix as yet..
Click to expand...
Click to collapse
If your are using usb 3.0 port then give a try with usb 2.0 port.
I tried usb 2.0 and 3.0.. I tried windows 7,8 and 10.. I tried a total of 4 computers.. I tried the original lg cable, HTC cable, Samsung cable and even a blackberry cable.. No avail..
Sent from my LG-D855 using XDA Forums
DarkStar22 said:
I tried usb 2.0 and 3.0.. I tried windows 7,8 and 10.. I tried a total of 4 computers.. I tried the original lg cable, HTC cable, Samsung cable and even a blackberry cable.. No avail..
Sent from my LG-D855 using XDA Forums
Click to expand...
Click to collapse
I flashed stock rom from LG flash tool more than 5 times, tried both kdz & tot but there is no problem at all. Did you follow all steps? Replaced .dll file? Changed port to com41?
Yes I did that. Idk what else to do...it's stuck at firmware upgrade screen.. That's all I get, even when I plug in the charger...
Sent from my LG-D855 using XDA Forums
Any error like dload 9008 something?
Previously i've made a post about how i can't unroot my LG G3 and that I can't leave Download mode/ Firmware update.
So when i got my LG G3 i tried to updated it from KitKat to Lollipop and then to Marshmellow but i couldn't, i have tried many methods so i did some research and came across that u "can't update a rooted phone" so this is what made me think that my phone is rooted.
So is my phone really rooted?
LetTheWolfsMeow said:
Previously i've made a post about how i can't unroot my LG G3 and that I can't leave Download mode/ Firmware update.
So when i got my LG G3 i tried to updated it from KitKat to Lollipop and then to Marshmellow but i couldn't, i have tried many methods so i did some research and came across that u "can't update a rooted phone" so this is what made me think that my phone is rooted.
So is my phone really rooted?
Click to expand...
Click to collapse
If you have any apps like "SuperSU" "KingRoot" then it might be Rooted.(Try installing from Play Store "Root checker")
And i don't really think that you have your phone rooted.
Many Phone Owners (From different manufacturers)don't get updated via OTA.
So they manually update OR wait.
And rooted phones get OTA updates.But if you update you lose your Root access. (That's how i understood that you don't have Root)
Hopefully you understood.
Greetings.
LetTheWolfsMeow said:
Previously i've made a post about how i can't unroot my LG G3 and that I can't leave Download mode/ Firmware update.
So when i got my LG G3 i tried to updated it from KitKat to Lollipop and then to Marshmellow but i couldn't, i have tried many methods so i did some research and came across that u "can't update a rooted phone" so this is what made me think that my phone is rooted.
So is my phone really rooted?
Click to expand...
Click to collapse
Download root checker from the playstore and see what it tells you.
Sotiris02 said:
If you have any apps like "SuperSU" "KingRoot" then it might be Rooted.(Try installing from Play Store "Root checker")
And i don't really think that you have your phone rooted.
Many Phone Owners (From different manufacturers)don't get updated via OTA.
So they manually update OR wait.
And rooted phones get OTA updates.But if you update you lose your Root access. (That's how i understood that you don't have Root)
Hopefully you understood.
Greetings.
Click to expand...
Click to collapse
Great!!! There just one slight problem, like i stated before i can't leave the Firmware update screen. Everytime i turn my phone on it just goes to the Firmware update screen and holding power button does nothing, taking the battery out turns the phone off but goes back to firmware update screen once it's turned on again.
startswithPendswithOOH said:
Download root checker from the playstore and see what it tells you.
Click to expand...
Click to collapse
I would, but like i stated before my phone is stuck in Firmware update screen so i can't access anything
LetTheWolfsMeow said:
Great!!! There just one slight problem, like i stated before i can't leave the Firmware update screen. Everytime i turn my phone on it just goes to the Firmware update screen and holding power button does nothing, taking the battery out turns the phone off but goes back to firmware update screen once it's turned on again.
Click to expand...
Click to collapse
Can you take a picture of it and send it here?
LetTheWolfsMeow said:
I would, but like i stated before my phone is stuck in Firmware update screen so i can't access anything
Click to expand...
Click to collapse
Oops...I forgot that part...my bad.
Just to clarify - you can't take over the air updates if your phone is rooted with custom recovery, but you can still flash them manually.
If you're stuck in firmware update mode all I can suggest is booting into recovery manually(pull your battery & put it back in, press vol down & power at the same time, hold until the system recovery screen pops up - you variant may be slightly different than my vs985 so google lg g3 how to enter recovery manually if my method doesn't work for you) and doing a factory reset and cache clear from there and see if it boots. Otherwise you'll need to start fresh and tot/kdz flash your way to up to date.
Google search how to tot/kdz flash your variant. If it's vs985 I can help a little, otherwise head on over to your variants general XDA section and there should be a tutorial on flashing stock firmware up for you. Going back to stock may sound painful, but as long as you have the right files for the flash tool and drivers for your PC it should go pretty smoothly.
*I believe some marshmallow ROMs did come with some sort of anti-rollback software, but since you were on kit kat and trying to upgrade(not downgrade) it shouldn't be a concern for you. You may want to be careful and read, read, read before you flash so you can avoid any troubles before you upgrade though.
Sotiris02 said:
Can you take a picture of it and send it here?
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sotiris02 said:
Can you take a picture of it and send it here?
Click to expand...
Click to collapse
http://imgur.com/a/0WUHg
startswithPendswithOOH said:
Oops...I forgot that part...my bad.
Just to clarify - you can't take over the air updates if your phone is rooted with custom recovery, but you can still flash them manually.
If you're stuck in firmware update mode all I can suggest is booting into recovery manually(pull your battery & put it back in, press vol down & power at the same time, hold until the system recovery screen pops up - you variant may be slightly different than my vs985 so google lg g3 how to enter recovery manually if my method doesn't work for you) and doing a factory reset and cache clear from there and see if it boots. Otherwise you'll need to start fresh and tot/kdz flash your way to up to date.
Google search how to tot/kdz flash your variant. If it's vs985 I can help a little, otherwise head on over to your variants general XDA section and there should be a tutorial on flashing stock firmware up for you. Going back to stock may sound painful, but as long as you have the right files for the flash tool and drivers for your PC it should go pretty smoothly.
*I believe some marshmallow ROMs did come with some sort of anti-rollback software, but since you were on kit kat and trying to upgrade(not downgrade) it shouldn't be a concern for you. You may want to be careful and read, read, read before you flash so you can avoid any troubles before you upgrade though.
Click to expand...
Click to collapse
Going into the Recovery Mode does nothing it just goes back to the Firmware screen after showing "recovery mode".
Doing a Factory Reset is the 1st thing i tried; i have a D855 (made in Korea, but there isn't a Korean D855 so i don't think it's Korean it was just made there i guess) and when i tried to download the tot files there were different D855 versions like European, Hong Kong and TWN but I only knew my was D855 and didn't see anything about being it a European or Hong Kong version so i have tried them all and none of them worked, it just failed at 6%. I used the tot and dll files, idk how the kdz one works since the flash tool requires tot. and dll. files
LetTheWolfsMeow said:
Going into the Recovery Mode does nothing it just goes back to the Firmware screen after showing "recovery mode".
Doing a Factory Reset is the 1st thing i tried; i have a D855 (made in Korea, but there isn't a Korean D855 so i don't think it's Korean it was just made there i guess) and when i tried to download the tot files there were different D855 versions like European, Hong Kong and TWN but I only knew my was D855 and didn't see anything about being it a European or Hong Kong version so i have tried them all and none of them worked, it just failed at 6%. I used the tot and dll files, idk how the kdz one works since the flash tool requires tot. and dll. files
Click to expand...
Click to collapse
Hmmm... What error does it display at 6%?
If you want to try the kdz method here is a link(it has firmware links and driver links included)... https://forum.xda-developers.com/showthread.php?t=2785089
And sometimes it's a good idea to uninstall any phone drivers on your PC, reboot, and re-install just the LGE drivers; flash tools can be finicky sometimes.
LetTheWolfsMeow said:
http://imgur.com/a/0WUHg
Click to expand...
Click to collapse
KDZ Flash Guide
So let's go on..!
Go here and select the first one.
http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/D855/Android+6.0/
Then go over here
http://forum.xda-developers.com/showthread.php?t=2785089
And scroll down to "How to flash ROM kdz method"
Connect your phone to your PC.
Download LG drivers(Not Verizon one's!)
Download Lguptool, unzip it,open the folder and inside of it where all the lguptool files are located move the kdz file that you downloaded.
Open lguptool with admin prompt!
Select type CMDA and phone mode DIAG
Select the kdz file and click "CSE Flash"
Then click "start"
A menu will appear,select language and click "Ok"
After all these steps you will need to wait till the phone boots.
Greetings.
Sotiris02 said:
KDZ Flash Guide
So let's go on..!
Go here and select the first one.
http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/D855/Android+6.0/
Then go over here
http://forum.xda-developers.com/showthread.php?t=2785089
And scroll down to "How to flash ROM kdz method"
Connect your phone to your PC.
Download LG drivers(Not Verizon one's!)
Download Lguptool, unzip it,open the folder and inside of it where all the lguptool files are located move the kdz file that you downloaded.
Open lguptool with admin prompt!
Select type CMDA and phone mode DIAG
Select the kdz file and click "CSE Flash"
Then click "start"
A menu will appear,select language and click "Ok"
After all these steps you will need to wait till the phone boots.
Greetings.
Click to expand...
Click to collapse
In the downloading process around 30% i get a message that the phone has been disconnected from the pc, i press retry and 1sec after the same message come up and so on, the downloading process continues and stops at 60%
startswithPendswithOOH said:
Hmmm... What error does it display at 6%?
If you want to try the kdz method here is a link(it has firmware links and driver links included)... https://forum.xda-developers.com/showthread.php?t=2785089
And sometimes it's a good idea to uninstall any phone drivers on your PC, reboot, and re-install just the LGE drivers; flash tools can be finicky sometimes.
Click to expand...
Click to collapse
I cant remember what error it was, and i no longer have those files to check it.
Using the kdz method in the downloading process around 30% i get a message that the phone has been disconnected from the pc, i press retry and 1sec after the same message come up and so on, the downloading process continues and stops at 60%
I also reinstalled the drivers and noticed that in the device manager in the ports section i dont see any lg drivers so that means i dont have lg drivers installed? even though it said installation was successful.
LetTheWolfsMeow said:
In the downloading process around 30% i get a message that the phone has been disconnected from the pc, i press retry and 1sec after the same message come up and so on, the downloading process continues and stops at 60%
Click to expand...
Click to collapse
Try using an other cable and an other usb port.
Sotiris02 said:
Try using an other cable and an other usb port.
Click to expand...
Click to collapse
I have tried 3 different Cables and 3 Ports all give the same result, but I think the problem is with my LG drivers, after i installed lg drivers i get this
http://imgur.com/wYlAnWl
So i think i have LG drivers installed but somehow it doesn't show on my ports, which means they're not installed correctly? I think this because long time ago i used to have the same drivers on this pc and it showed them in the ports section.
I uninstalled the drivers and restarted my pc and reinstalled them and after it said "installation was successful" they still didn't show in the ports section.
I also have tried installing different version of lg drivers.
What is it i'm missing?
LetTheWolfsMeow said:
I have tried 3 different Cables and 3 Ports all give the same result, but I think the problem is with my LG drivers, after i installed lg drivers i get this
http://imgur.com/wYlAnWl
So i think i have LG drivers installed but somehow it doesn't show on my ports, which means they're not installed correctly? I think this because long time ago i used to have the same drivers on this pc and it showed them in the ports section.
I uninstalled the drivers and restarted my pc and reinstalled them and after it said "installation was successful" they still didn't show in the ports section.
I also have tried installing different version of lg drivers.
What is it i'm missing?
Click to expand...
Click to collapse
Are you using windows 10?
That should be the problem.(Many people have problems with lguptool in windows 10.)
The only thing that you can do is to downgrade your Windows to 7.Or go to a "internet cafe" (as they always have Windows 7 installed).
(That's also a reason i stay with Windows 7 Ultimate )
Sotiris02 said:
Are you using windows 10?
That should be the problem.(Many people have problems with lguptool in windows 10.)
The only thing that you can do is to downgrade your Windows to 7.Or go to a "internet cafe" (as they always have Windows 7 installed).
(That's also a reason i stay with Windows 7 Ultimate )
Click to expand...
Click to collapse
Yes, i have windows 10.
If i go to a internet cafe; don't they have some kind of restriction, preventing u to download stuff like lguptool etc.
LetTheWolfsMeow said:
Yes, i have windows 10.
If i go to a internet cafe; don't they have some kind of restriction, preventing u to download stuff like lguptool etc.
Click to expand...
Click to collapse
No i don't think so.
Sotiris02 said:
No i don't think so.
Click to expand...
Click to collapse
So i finally found time to go to an internet cafe and still i get the same results, in the download process it still says phone has been disconnected from the pc, downloaded the drivers and still they don't show in the
"ports" section in device manager. Also, when i connect my phone to the pc it says "usb device not recognized" is it because it's in download mode/firmware update screen. And finally i can't run lgflash 2014 in admin promt in an internet cafe.
I might just give up and save up for a new phone...
Hello All,
I was trying to downgrade my lenovo vib1 p1a42 into lolipop,between flashing I disconnected my phone mistakenly.Since on that it never goes into android.Just shows lenovo logo only.
I was tried with reboot into recovery mode(switching on phone with pressing Vol +/- button), but it doesn't boots like that just shows same screen,
So i'm not able to flash again
please help me
thanks you all
nathar.kamal said:
Hello All,
I was trying to downgrade my lenovo vib1 p1a42 into lolipop,between flashing I disconnected my phone mistakenly.Since on that it never goes into android.Just shows lenovo logo only.
I was tried with reboot into recovery mode(switching on phone with pressing Vol +/- button), but it doesn't boots like that just shows same screen,
So i'm not able to flash again
please help me
thanks you all
Click to expand...
Click to collapse
Do u have download mode? Press volume up and connect to pc, do u see anything in devicemanager?
Starchm said:
Do u have download mode? Press volume up and connect to pc, do u see anything in devicemanager?
Click to expand...
Click to collapse
I dont know what is download mode?
i did by pressing vol + up and connect to pc after sometimes it shows as in the image
Lenovo HS-USB Diagnostics(COM14)
Lenovo HS-USB NMEA(COM15)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is screenshot of mobile shows menu
reboot
install update package
wipe user data
power off
nathar.kamal said:
I dont know what is download mode?
i did by pressing vol + up and connect to pc after sometimes it shows as in the image
Lenovo HS-USB Diagnostics(COM14)
Lenovo HS-USB NMEA(COM15)
This is screenshot of mobile shows menu
reboot
install update package
wipe user data
power off
Click to expand...
Click to collapse
Try this Download the lenovo driver http://www.mediafire.com/file/ofvviq....1.13_user.exe
Download the QPST http://www.mediafire.com/file/95cth8...22+(1).zip and install it
Download the latest rom =it is the s288 1,79GB= https://yadi.sk/d/hY3kNWJGrnpCU?ncrnd=5389
Extract the rom to your desktop
Power off your phone
Press only Volume UP button, and connect to your pc with an usb cable
open QFIL, then select the programmer path in your rom folder
Then load xml select rawprogram0 then patch0
Start the flash, it will take a much time
Hi,
I have downloaded update.zip from other site and copied into sdcard.Installed fine.but no sim card is detected.no serial no,no imei no,no device I'd.
WT can I do
nathar.kamal said:
Hi,
I have downloaded update.zip from other site and copied into sdcard.Installed fine.but no sim card is detected.no serial no,no imei no,no device I'd.
WT can I do
Click to expand...
Click to collapse
write your facebook link in pm to me or telegram or etc if u have.
Even after flashing stock ROM S288 using QFIL. My boot loader status is showing unlocked. What should I do to relock it? Can U help?
SVR said:
Even after flashing stock ROM S288 using QFIL. My boot loader status is showing unlocked. What should I do to relock it? Can U help?
Click to expand...
Click to collapse
Why u want to lock it?
btw try fastboot oem lock in fastboot mode.
Starchm said:
Why u want to lock it?
btw try fastboot oem lock in fastboot mode.
Click to expand...
Click to collapse
This command is not working. I'm trying in windows 10 though. Hmm.. To get back to pure stock with bl locked.
---------- Post added at 09:01 AM ---------- Previous post was at 08:59 AM ----------
Starchm said:
Why u want to lock it?
btw try fastboot oem lock in fastboot mode.
Click to expand...
Click to collapse
I thought flashing with qfil raw rom will lock the boot loader back. But it didn't.. ?
SVR said:
This command is not working. I'm trying in windows 10 though. Hmm.. To get back to pure stock with bl locked.
---------- Post added at 09:01 AM ---------- Previous post was at 08:59 AM ----------
I thought flashing with qfil raw rom will lock the boot loader back. But it didn't.. ?
Click to expand...
Click to collapse
Flash the rom with rawprogram0.xml?
Starchm said:
Flash the rom with rawprogram0.xml?
Click to expand...
Click to collapse
Yes. Did the same. After selecting rawprogram.xml it's asking to select patch0.xml there is no way to deseelct patch0.xml. . Am i doing something wrong.?? Stock ROM, Stock Recovery but BL unlocked
SVR said:
Yes. Did the same. After selecting rawprogram.xml it's asking to select patch0.xml there is no way to deseelct patch0.xml. . Am i doing something wrong.?? Stock ROM, Stock Recovery but BL unlocked
Click to expand...
Click to collapse
Where u see your bootloader is unlocked?
Starchm said:
Where u see your bootloader is unlocked?
Click to expand...
Click to collapse
Using adb method entering boot loader mode. On mobile screen as well as by typing command.
SVR said:
Using adb method entering boot loader mode. On mobile screen as well as by typing command.
Click to expand...
Click to collapse
I wanna ask again, why u need locked bootloader? anyway u can try other older roms to flash it.
Starchm said:
I wanna ask again, why u need locked bootloader? anyway u can try other older roms to flash it.
Click to expand...
Click to collapse
To get OTA if any in future.
SVR said:
To get OTA if any in future.
Click to expand...
Click to collapse
No chance but try older roms
SVR said:
To get OTA if any in future.
Click to expand...
Click to collapse
fastboot oem lock-go?
really bingo
nathar.kamal said:
Hi,
I have downloaded update.zip from other site and copied into sdcard.Installed fine.but no sim card is detected.no serial no,no imei no,no device I'd.
WT can I do
Click to expand...
Click to collapse
Is that true you were able to boot. Do you have your data left??? or everything wiped off.
I have same problem. If data is safe I will do this. Then Backup my data. then will use Stock ROM to bootloop it again then I will goto Service centre with a big smile on my face. They will deal it.
My Lg just froze and rebootet into the normal boot screen where it just stays
I tried to factory reset it but it just says erase for a short moment and goes back to Lg Logo
I tried Lgup with a Stock rom for the LG it finishes everything but just goes into Lg logo again
Any Help??
Leon200318 said:
My Lg just froze and rebootet into the normal boot screen where it just stays
I tried to factory reset it but it just says erase for a short moment and goes back to Lg Logo
I tried Lgup with a Stock rom for the LG it finishes everything but just goes into Lg logo again
Any Help??
Click to expand...
Click to collapse
Anyone with the same problem or a fix?
Leon200318 said:
Anyone with the same problem or a fix?
Click to expand...
Click to collapse
You have either bricked the phone or its not the correct rom,
Try a different rom, Maybe you can restore it with TWRP if you installed it, Or try download mode.
Eevvaann6 said:
You have either bricked the phone or its not the correct rom,
Try a different rom, Maybe you can restore it with TWRP if you installed it, Or try download mode.
Click to expand...
Click to collapse
The Rom is from the official Lg site tried 2 different
I dont have a recovery cause i cant get into fastboot neither recovery mode
Just lg logo mode and download mode/firmware update mode.
I go try some other roms
Leon200318 said:
The Rom is from the official Lg site tried 2 different
I dont have a recovery cause i cant get into fastboot neither recovery mode
Just lg logo mode and download mode/firmware update mode.
I go try some other roms
Click to expand...
Click to collapse
Make sure its for the correct model, I have a LG K10 the firmware is on the LG site but I have a At&t model which doesn't have official firmware from the sites. To get into android recovery which might help see your phone is bricked install ADB and Fastboot and run "adb reboot recovery" Also some LG phones don't have Fastboot like the At&t of the LG K10 Which I have. Hope you can get it to work
---------- Post added at 04:02 AM ---------- Previous post was at 03:58 AM ----------
Also try Safe mode, you could try it maybe you can get into it, so if that is the case, its probably something with what you did or how you flashed, if you still can't get it to work maybe wrong firmware.
Eevvaann6 said:
Make sure its for the correct model, I have a LG K10 the firmware is on the LG site but I have a At&t model which doesn't have official firmware from the sites. To get into android recovery which might help see your phone is bricked install ADB and Fastboot and run "adb reboot recovery" Also some LG phones don't have Fastboot like the At&t of the LG K10 Which I have. Hope you can get it to work
---------- Post added at 04:02 AM ---------- Previous post was at 03:58 AM ----------
Also try Safe mode, you could try it maybe you can get into it, so if that is the case, its probably something with what you did or how you flashed, if you still can't get it to work maybe wrong firmware.
Click to expand...
Click to collapse
Adb doesnt find the phone i only can get into download mode and there it doesnt get recognized
My phone hasnt got fastboot too
I tried many firmwares now, neither of them work i tried to do it with lg bridge and it doesnt work either all of the firmwares where for my lg k10 m250n
Is there another way to get into recovery
Bit more information:
When i try to start it in safe mode it shows lg logo goes for a short while to a screen where it shows "erasing" then just goes to lg logo again.
And again another thing: the phone behaves the same if I flash the wrong rom it does the exact same.
Leon200318 said:
Adb doesnt find the phone i only can get into download mode and there it doesnt get recognized
My phone hasnt got fastboot too
I tried many firmwares now, neither of them work i tried to do it with lg bridge and it doesnt work either all of the firmwares where for my lg k10 m250n
Is there another way to get into recovery
Bit more information:
When i try to start it in safe mode it shows lg logo goes for a short while to a screen where it shows "erasing" then just goes to lg logo again.
And again another thing: the phone behaves the same if I flash the wrong rom it does the exact same.
Click to expand...
Click to collapse
How do you try to start that safe mode? What buttons you used?
>Is there another way to get into recovery
Go into download mode and using Send_Command
or lglaf.py give it this command: multi_init
There push Vol+ and then Power once.
CXZa said:
How do you try to start that safe mode? What buttons you used?
>Is there another way to get into recovery
Go into download mode and using Send_Command
or lglaf.py give it this command: multi_init
There push Vol+ and then Power once.
Click to expand...
Click to collapse
Wow didn't thought someone reply to this after the long time I just say thx for response even if it's not workin
I don't even know which buttons I used for safe mode but I can look after it later
I'll give it a try with the python script when I get to my pc tomorrow
Will be Posting the results directly after
Also 2 more questions
What does the recovery look like on the LG k10
And can I flash custom recovery zips with that?
Leon200318 said:
Wow didn't thought someone reply to this after the long time I just say thx for response even if it's not workin
I don't even know which buttons I used for safe mode but I can look after it later
I'll give it a try with the python script when I get to my pc tomorrow
Will be Posting the results directly after
Click to expand...
Click to collapse
The Send_Command might be easier. With that py you have mod it a bit and use an older version drivers. Was it 4.04 or something, then it works.
If you're using Windows that is... Then there is Steadfasterx's and some other lglaf versions that might work...
With send_command you just find the the COM port the diagnose or whatever uses, like:
reg query HKLM\hardware\devicemap\SERIALCOMM
And then: Send_Command.exe \\.\COM[com port number]
Send_Command.exe \\.\COM22
Then you can give that command, and by default it will boot to the recovery.
In recovery there is that dead android guy waiting, that's why those buttons.
Custom zips: No way. Now keys to sign them... and the bootloader should be
unlocked to do any changes...
CXZa said:
The Send_Command might be easier. With that py you have mod it a bit and use an older version drivers. Was it 4.04 or something, then it works.
If you're using Windows that is... Then there is Steadfasterx's and some other lglaf versions that might work...
With send_command you just find the the COM port the diagnose or whatever uses, like:
reg query HKLM\hardware\devicemap\SERIALCOMM
And then: Send_Command.exe \\.\COM[com port number]
Send_Command.exe \\.\COM22
Then you can give that command, and by default it will boot to the recovery.
In recovery there is that dead android guy waiting, that's why those buttons.
Custom zips: No way. Now keys to sign them... and the bootloader should be
unlocked to do any changes...
Click to expand...
Click to collapse
I have access to both Windows and Ubuntu
I Will try what you said and just will look if it works
What are my options to do when I'm in recovery mode?
Leon200318 said:
What are my options to do when I'm in recovery mode?
Click to expand...
Click to collapse
Basically the factory reset. Fastboot/bootloader doesn't work.
>There push Vol+ and then Power once.
edit: Actually, it is other way around. Push Power and then Vol+ once.
CXZa said:
Basically the factory reset. Fastboot/bootloader doesn't work.
>There push Vol+ and then Power once.
Actually, try with Vol- if Vol+ doesn't do the trick. Don't remember these so well anymore.
Click to expand...
Click to collapse
I have done many factory resets
They start with a screen saying "erasing" and then just stop then it restarts two times and then just go into LG screen again
Leon200318 said:
Anyone with the same problem or a fix?
Click to expand...
Click to collapse
Same problem, and i cant acces to recovery or bootloader, and im searching for scatter file to use sp flash tools.
javier8340 said:
Same problem, and i cant acces to recovery or bootloader, and im searching for scatter file to use sp flash tools.
Click to expand...
Click to collapse
I don't have the bootloader too but I guess yours Is locked too like mine
But that doesn't help me.
I have download mode and recovery mode where the only option is to factory reset it.
Adb doesn't work
And it doesn't made a change for me if I flash a OS that is right or if I flash a OS that is wrong.
It does the same with both so I can't see how I should ever revive it.
Mabye a custom recovery packed into the OS file but idk how and where to get one.
Leon200318 said:
I don't have the bootloader too but I guess yours Is locked too like mine
But that doesn't help me.
I have download mode and recovery mode where the only option is to factory reset it.
Adb doesn't work
And it doesn't made a change for me if I flash a OS that is right or if I flash a OS that is wrong.
It does the same with both so I can't see how I should ever revive it.
Mabye a custom recovery packed into the OS file but idk how and where to get one.
Click to expand...
Click to collapse
I have seen a video where a men do a reflow and works but i dont know if is these the problem, i think its dead.