Develop Bugs

Flash stock rom - Keep Root & CWM

Hello, I am currently rooted and have CWM 6.0.4.3. installed. I'm on CM11 but want to go back to stock.. Is there an easy way to keep root and go back to stock. Want stock for a few functions that ROMS dont seem to be offering but can keep root and CWM ??
Thanks.

Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.

Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins

DeathNotice said:
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
Click to expand...
Click to collapse
Ok perfect, thats what I was looking for. Phone btw is S3 - d2att - SGH i747) Sounds good to install the stock rom and re-root.. I'm sure its here but I have searched everywhere to find a tutorial on this and I cannot find a straight answer.
Would you mind giving me the steps or pointing me to a thread that explains how to and has the files in need to download ?

audit13 said:
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Click to expand...
Click to collapse
Do you know if there is a step by step on this somewhere ? I dont mind going back to complete stock.. I can just re-root and flash CWM after.
OR
Maybe you could just answer the bigger question : the reason I want to go back to stock is I need to use MHL/HDMI which CM11 doesnt support. I dont want to go back to stock, I would rather even go to another ROM that supports mhl/hdmi.. but if I have to go to stock, than so be it.?

Were you running the stock AT&T 4.3 ROM before you switched to CM11?

audit13 said:
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
Click to expand...
Click to collapse
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.

robberrobbie said:
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
Click to expand...
Click to collapse
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426

audit13 said:
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
Click to expand...
Click to collapse
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?

robberrobbie said:
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
Click to expand...
Click to collapse
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att

audit13 said:
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
Click to expand...
Click to collapse
Ok thanks, I will do that. 1 thing I'm not quite sure of is the bootloader situation ? In the first tutorial there is a note : Flashing a prior bootloader can hard/soft brick your device. How do I know ?
I see the steps as:
Extract tar file you downloaded.
Use Odin, put phone into download mode [with phone off, hold vol. down + home + power ], connect to computer and open Odin.
once in odin click the PDA field and select the tar file
Leave Auto Reboot and F. Reset Time checked.
click start and when done let phone reboot.
If you just want a stock, rooted phone with no custom recovery, no plans to flash custom roms, etc. then you can stop HERE.
For my situation, is it just that easy ?

Before flashing, verify the version of your bootloader.

audit13 said:
Before flashing, verify the version of your bootloader.
Click to expand...
Click to collapse
OK I have made an effort to go read and figure out how to find out what version of bootloader on my own.. But i cannot find ? Any chance you know... And could help?

You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?

Hey. I got the i747m. As for what was the last stock ROM I had, can't say. I know when I bought the phone it was ICS and I had received and update to jellybean.. But them went to cm10. The tutorial I followed told me had me back everything up, which I did. Have it in a file somewhere on my comp, would that tell me ?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app

If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app

Ariesdroid said:
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have not seen a stock mf1 ROM that can be flashed in CWM. You could use mobile Odin to flash back to stock and then flash Philz Touch via desktop Odin later.

OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?

audit13 said:
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Click to expand...
Click to collapse
Hey there Audit, Sorry to bother you again, I just dont know how to move forward from here and neeeeeed some help.
I have been reading for days and days have not found a straight answer for my issue and I dont want to just go ahead and start flashing when I dont know if its the right method ?
I dont know how to get back to stock from where I'm at, I dont know how to figure out what bootloader I have (you asked me)
I have found a couple links on XDA that I can follow, I'm just not sure if they apply to my situation ?
This is a pretty detailed response/tutorial, but I dont know if I can just go ahead with this or not ?
http://forum.xda-developers.com/showthread.php?t=2186967
This is also very detailed: http://forum.xda-developers.com/showthread.php?t=1739426
Any help would be greatly appreciated !

robberrobbie said:
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
Click to expand...
Click to collapse
If you are sure you have the Rogers i747m and you have never loaded a stock Rogers 4.3 ROM onto your phone, you could use desktop Odin to flash a pre-rooted 4.1.2 ROM from here: http://forum.xda-developers.com/showthread.php?t=1739426.
Flashing the pre-rooted 4.1.2 ROM will return the phone to completely stock, wipe out all installed apps and data, and you will have root. I do not recommend flashing the Rogers 4.3 pre-rooted ROM from the link.
Once you are able to boot into the phone and set things up, you can flash Philz Touch from Odin which will give you a custom recovery on a rooted stock 4.1.2 ROM.

Stock 4.4.2 Bootloader?

Wanting to drop stock(latest) back onto my phone as the person buying it wants that. I want to say I remember reading I needed a newer bootloader for 4.4.2. I got my device on launch and got tired of waiting and went to CM11.
What if anything other than clearing data/cache and flashing the stock deodexed/rooted ROM would I need to do? If there is a bootloader, is it a separate odin file? or flashable .zip?

muqali said:
Wanting to drop stock(latest) back onto my phone as the person buying it wants that. I want to say I remember reading I needed a newer bootloader for 4.4.2. I got my device on launch and got tired of waiting and went to CM11.
What if anything other than clearing data/cache and flashing the stock deodexed/rooted ROM would I need to do? If there is a bootloader, is it a separate odin file? or flashable .zip?
Click to expand...
Click to collapse
If you're on 4.3 still you will have to Odin a stock 4.3 firmware on to the phone. You can not have a custom recovery on the phone so the Odin way will also replace the custom recovery with stock recovery. Then once your phone is stock, you can then take the update to 4.4.2
If I'm not mistaken, you should download the 4.4.2 fw and Odin that on you phone as well. Even though you are Odining your new fw, the phone must be fully stock or that update will still fail.

Eric214 said:
If you're on 4.3 still you will have to Odin a stock 4.3 firmware on to the phone. You can not have a custom recovery on the phone so the Odin way will also replace the custom recovery with stock recovery. Then once your phone is stock, you can then take the update to 4.4.2
If I'm not mistaken, you should download the 4.4.2 fw and Odin that on you phone as well. Even though you are Odining your new fw, the phone must be fully stock or that update will still fail.
Click to expand...
Click to collapse
Well I was on 4.3 stock then went to Cyanogen 4.4.2. I've now got the deodexed/rooted stock 4.4.2 from the forum here and was able to boot it using leankernel. It works and the buyer is satisfied with it. He know how to flash updated ROMs so he can change later anyway. Thanks for the response though, I was thinking noone was gonna answer.

re: latest stock rom
muqali said:
Wanting to drop stock(latest) back onto my phone as the person buying it wants that. I want to say I remember reading I needed a newer bootloader for 4.4.2. I got my device on launch and got tired of waiting and went to CM11.
What if anything other than clearing data/cache and flashing the stock deodexed/rooted ROM would I need to do? If there is a bootloader, is it a separate odin file? or flashable .zip?
Click to expand...
Click to collapse
If you want the newest/latest official stock N900T KitKat firmware why not do the following:
You need to download and Odin flash the official stock KitKat N900T NE6 firmware.
Here is the direct fast download link for it:
http://www.androidfilehost.com/?fid=23501681358537528
The above zip file also contains Odin, CF-Autoroot and TWRP 2.7.0.1 recovery.
Be sure to go into recovery before Odin flashing NE6 and do a factory data reset
and a full wipe. Optional: Then Odin flash cf-autoroot and the TWRP 2.7.0.1.
If you want more information and or instructions here is the link:
http://forum.xda-developers.com/show...60&postcount=2
If you want the older official stock N900T 4.4.2 NB4 KitKat rom you can
download it from: http://tekunix.com/downloads/TMB-N900TUVUCNB4-20140305155920.zip
and Odin flash it instead of the stock NE6 official N900T firmware.
Both the older and newer official Kitkat stock roms come with the required bootloaders/baseband.
Good luck!

Misterjunky said:
If you want the newest/latest official stock N900T KitKat firmware why not do the following:
You need to download and Odin flash the official stock KitKat N900T NE6 firmware.
Here is the direct fast download link for it:
http://www.androidfilehost.com/?fid=23501681358537528
The above zip file also contains Odin, CF-Autoroot and TWRP 2.7.0.1 recovery.
Be sure to go into recovery before Odin flashing NE6 and do a factory data reset
and a full wipe. Optional: Then Odin flash cf-autoroot and the TWRP 2.7.0.1.
If you want more information and or instructions here is the link:
http://forum.xda-developers.com/show...60&postcount=2
If you want the older official stock N900T 4.4.2 NB4 KitKat rom you can
download it from: http://tekunix.com/downloads/TMB-N900TUVUCNB4-20140305155920.zip
and Odin flash it instead of the stock NE6 official N900T firmware.
Both the older and newer official Kitkat stock roms come with the required bootloaders/baseband.
Good luck!
Click to expand...
Click to collapse
So clear data/factory reset and clear cache in recovery. Reboot into download and flash NE6, then cf-autoroot, then TWRP? I didn't see you say exactly when to flash NE6.

Going back to stock from cm11?

I'm on cm11 m9 and it's been acting hellafunky lately, so I figured I'd switch back to stock to see if that cleared it up. I know TW is still on 4.4.3 but I can't find a flashable image of it anywhere. Is it possible to go back to stock, or are the cm bootloaders and such to new to be able to do this without bricking the device?

What bootloader is on your phone? Is it an i747 or i747m?
If you are on 4.3 or higher, you cannot flash back to stock unless you use a ROM that has been specifically compiled for flashing in Odin.

audit13 said:
What bootloader is on your phone? Is it an i747 or i747m?
If you are on 4.3 or higher, you cannot flash back to stock unless you use a ROM that has been specifically compiled for flashing in Odin.
Click to expand...
Click to collapse
On bootloader NE4, I was able to flash back to to stock using the image in here: http://forum.xda-developers.com/showthread.php?p=56510020
Everything is working swimmingly.

'ENEWMAN17' threads are the most helpful when it comes to returning an SGS3 device back to stock KitKat ROM. You must strictly adhere to his instructions. Good luck!

Iv flashed my cm11 back to stock using cwm and flashing a odexed 4.4.2 samsung rom without any problems.

slicetwo said:
On bootloader NE4, I was able to flash back to to stock using the image in here: http://forum.xda-developers.com/showthread.php?p=56510020
Everything is working swimmingly.
Click to expand...
Click to collapse
If the phone is an i747m, I recommend getting a stock ROM from sammobile. com. I'm not sure if a bootloader and modem file is included in the enewman17's thread but flashing an i747 bootloader and modem onto an i747m could result in a brick.

[Q] No carrier/SIM support after 4.3 stock restore

My ATT SGH-i747 was rooted and running 4.4.2 until an OTA this past weekend soft-bricked the phone. Phone would boot to a blank screen but still allowed access to download and recovery modes, thankfully.
With help from this awesome forum, and a stock 4.3 flash via ODIN, thanks to enewman17's epic efforts and thread , the phone is back, but now won't recognize the SIM - and baseband version is "unknown" - I suspect I need to now go up to 4.4.2 to get the hw recognized by the sw. Went to ATT and they put a new SIM in but to no avail
CWM recovery is gone, but I can reload that easily enough...
Do I need to just flash the modem, or is the bootloader involved too?
Is there a single flash or .zip that will get the ROM (incl CSC and Modem) up to 4.4.2 in one shot?
I never really wanted to go this deep but here I am so now I'm looking for advice or direction as there are so many directions to look... thanks in advance!

Mismatch in firmware
Digging deeper, using Phone Info *Samsung*, I have noted the following
bootloader version: I747UCUFNJ1
baseband version: <blank>
pda version: I747UCUEMJB
csc version: I747ATTEMJB
skip a bit...
modem version: <blank>
hardware revision: <blank>
mobile operator name: <blank>
mobile network code: <blank>
So it would seem I have a mis-match of versions, where it seems all should be the same..
Would it be safe to flash to MJB following this thread?
http://forum.xda-developers.com/galaxy-s3-att/general/ucuemjb-to-ucufne4-firmware-update-t2808654

OCTANEJUNKIE said:
My ATT SGH-i747 was rooted and running 4.4.2 until an OTA this past weekend soft-bricked the phone. Phone would boot to a blank screen but still allowed access to download and recovery modes, thankfully.
With help from this awesome forum, and a stock 4.3 flash via ODIN, thanks to enewman17's epic efforts and thread , the phone is back, but now won't recognize the SIM - and baseband version is "unknown" - I suspect I need to now go up to 4.4.2 to get the hw recognized by the sw. Went to ATT and they put a new SIM in but to no avail
CWM recovery is gone, but I can reload that easily enough...
Do I need to just flash the modem, or is the bootloader involved too?
Is there a single flash or .zip that will get the ROM (incl CSC and Modem) up to 4.4.2 in one shot?
I never really wanted to go this deep but here I am so now I'm looking for advice or direction as there are so many directions to look... thanks in advance!
Click to expand...
Click to collapse
Your modem (baseband) appears to have been compromised in the process of downgrading from Kitkat. You could try either of the following solutions...
1) Flash the UCUEMJB modem via custom recovery to return you to complete stock 4.3. You can see the modem file here ....
https://www.androidfilehost.com/?fid=23269279319197285
2) Do a complete stock restore to 4.4.2. You can find the stock update zip via the following thread ...
http://forum.xda-developers.com/galaxy-s3-att/general/ucuemjb-to-ucufne4-firmware-update-t2808654
If you can reflash the 4.3MJB modem, you can check to see if you can get an OTA update to 4.4.2. Using Option 2 requires you to be on complete stock 4.3 so this may not work if you currently don't have the baseband/modem. I would strongly advise you stick to the custom recovery flashable files for now and avoid Odin. You would, however, need to restore custom recovery via Odin.
Hope this works for you.

Larry2999 said:
Your modem (baseband) appears to have been compromised in the process of downgrading from Kitkat. You could try either of the following solutions...
1) Flash the UCUEMJB modem via custom recovery to return you to complete stock 4.3. You can see the modem file here ....
https://www.androidfilehost.com/?fid=23269279319197285
2) Do a complete stock restore to 4.4.2. You can find the stock update zip via the following thread ...
http://forum.xda-developers.com/galaxy-s3-att/general/ucuemjb-to-ucufne4-firmware-update-t2808654
If you can reflash the 4.3MJB modem, you can check to see if you can get an OTA update to 4.4.2. Using Option 2 requires you to be on complete stock 4.3 so this may not work if you currently don't have the baseband/modem. I would strongly advise you stick to the custom recovery flashable files for now and avoid Odin. You would, however, need to restore custom recovery via Odin.
Hope this works for you.
Click to expand...
Click to collapse
Thanks for the detailed reply with links, Larry :good:
So I guess my plan of actions will be
1) re-install custom recovery w CWM to my external SD card as was previous
-do I *need* later version of CWM? Previous one of mine was 6.0.2.3, IIRC, that is what I can easily flash back to the phone
2) install .zip (from https://www.androidfilehost.com/?fid=23269279319197285) via CWM
If that doesn't work, I was interested in the S3Rx ROM vs. a stock 4.4.2 ROM - is there any way to go straight to a custom 4.4.2 ROM or should I get the modem working in 4.3 first?
Lastly, Where can I find a later version of a CW Recovery Touch .tar to flash via ODIN? (third stoopid noob question in this post, I know...)

Attempt to flash d2att_I747UCUEMJB_bootloader_modem_4.3.zip via CWM Recovery FAILED with Status 7, Installation aborted...
Bootloader version: I747UCUFNJ1
Baseband version: <blank>
Blank stare into space...

OCTANEJUNKIE said:
Attempt to flash d2att_I747UCUEMJB_bootloader_modem_4.3.zip via CWM Recovery FAILED with Status 7, Installation aborted...
Bootloader version: I747UCUFNJ1
Baseband version: <blank>
Blank stare into space...
Click to expand...
Click to collapse
You aren't the first to have this issue. This is why I am still on NE4 and did not take the OTA to NJ1. The update is pointless anyway, all it does is patch the kernel so towelroot won't work anymore aside from updating the bootloader.
Since your bootloader is NJ1, that is your firmware which cannot be downgraded. If you try, you will brick. You have to work with NJ1 files here only. Sure you can flash older modems, but stick to NJ1. I suggest using ODIN to flash a custom recovery, then use enewman17's NJ1 .zip file in said recovery to reflash all the NJ1 stuff. Then do a complete factory reset. You might need to flash stock recovery to do the hard factory data reset, as I am not sure if it can be done in CWM or TWRP.
In the future, I suggest freezing the update and not upgrading until people on here do it and report how it's working or rather not working in this case.

StoneyJSG said:
You aren't the first to have this issue. This is why I am still on NE4 and did not take the OTA to NJ1. The update is pointless anyway, all it does is patch the kernel so towelroot won't work anymore aside from updating the bootloader.
Since your bootloader is NJ1, that is your firmware which cannot be downgraded. If you try, you will brick. You have to work with NJ1 files here only. Sure you can flash older modems, but stick to NJ1. I suggest using ODIN to flash a custom recovery, then use enewman17's NJ1 .zip file in said recovery to reflash all the NJ1 stuff. Then do a complete factory reset. You might need to flash stock recovery to do the hard factory data reset, as I am not sure if it can be done in CWM or TWRP.
In the future, I suggest freezing the update and not upgrading until people on here do it and report how it's working or rather not working in this case.
Click to expand...
Click to collapse
Thanks for the response, Stoney :good:
I have CWM and TeamEpic v5 on external SD, so a version of custom recovery is there (CWM 6.0.2.3) - but do you have a link to enewman17's NJ1 .zip /recovery?
As far as freezing the updates in the future, yes. I tried to keep the OTA push from happening, apparently not ardently enough :crying:

OCTANEJUNKIE said:
Thanks for the response, Stoney :good:
I have CWM and TeamEpic v5 on external SD, so a version of custom recovery is there (CWM 6.0.2.3) - but do you have a link to enewman17's NJ1 .zip /recovery?
As far as freezing the updates in the future, yes. I tried to keep the OTA push from happening, apparently not ardently enough :crying:
Click to expand...
Click to collapse
Not a problem, glad to help when I can. I THINK this is the link you need: http://forum.xda-developers.com/galaxy-s3-att/general/ucufne4-to-ucufnj1-update-t2941792
You might want to post in that thread asking if it works when you are already on NJ1 though, or get a hold of enewman17 via PM or something.

SOLVED!
enewman17 posted NJ1 modem .zip here, and now me has modem and cellular service again!
Question: can I update the thread tag from [Q] to [SOLVED] myself?

Try editing your original post.

audit13 said:
Try editing your original post.
Click to expand...
Click to collapse
Yup... Done [emoji222] [emoji222] [emoji222]

[Q] Questions about going back to stock.

Hey guys,
I was running Cyanogenmod 11 for a while which I installed using the automatic tool online. During the summer I flashed Dirty Unicorns but I have issues with the camera and random rebooting. I just got a Galaxy Gear for Christmas and I've read that its only compatible with touchwiz roms.
I'm trying to go back to stock and I am ok with losing my root access.
I have an SGH-1747m on Baseband I747MVLUEMK5 and my service provider is Bell. The android version is 4.4.4 currently. Whats the easiest method to do this? I've read some concerning information that going back to an earlier version of android will soft brick your phone, but I believe the most current Bell firmware is still in Jelly Bean.
Is it as easy as downloading the correct firmware and flashing it using Clockworkmod Recovery?
Thanks

You should download the stock ROM from sammobile.com and flash it in Odin to get back to stock.

audit13 said:
You should download the stock ROM from sammobile.com and flash it in Odin to get back to stock.
Click to expand...
Click to collapse
The latest version available for my baseband is 4.3. Will I run into problems going from 4.4.4 to 4.3?

Flashing in Odin will flash everything, including the bootloader and modem.

audit13 said:
Flashing in Odin will flash everything, including the bootloader and modem.
Click to expand...
Click to collapse
Thanks. So if I'm understanding correctly I just flash the latest firmware released by my carrier (4.4.2)? Is there anything else to watch out for when choosing the firmware?
Also, before flashing should I make a backup with Clockwork Recovery or any other program? Will Clockwork Recovery still be present after flashing with ODIN?

ZombieLee said:
Thanks. So if I'm understanding correctly I just flash the latest firmware released by my carrier (4.4.2)? Is there anything else to watch out for when choosing the firmware?
Also, before flashing should I make a backup with Clockwork Recovery or any other program? Will Clockwork Recovery still be present after flashing with ODIN?
Click to expand...
Click to collapse
Yes, flash the latest firmware for your phone. Be sure it's firmware for the i747m and not anything else. Always make a backup if you ever screw up or want to go back to where you are now. You will lose everything by flashing the stock firmware with ODIN, even clockwork mod recovery.

Thanks. When I made a backup before going to Dirty Unicorns I used Clockwork Recovery. If Clockwork will be deleted by flashing with ODIN, how would I utilize that backup if I needed it? Should I use another program to back up?
EDIT: I flashed it and everything went smoothly. Sincere thanks to everyone who gave me help!