Related
Hi guys,
I dropped my phone in water
I just left it until it's being dry, I turned it on and its works but the touch become crazy
sometime work and sometime not until it's doesn't work at all = no touch
I've sent the device to Vodafone to repair it because the warranty associate with them .
And they said the device can't be fixed
Also the problem in the (Lower mother board).
I am really confused , I am not sure where is the problem coz one of my friend said ,
if the device work and just the touch does't work, then the problem will be in the touch screen only.
Thanks in advance for your help guys .
Water dammage is not covered by warranty, ever.
If the digitizer does not function its either that there is still water in the device and is causing a short, or part of the circutry for the digitizer is fried.
Pull the batt and place the device in a hot area (about 30-35 degrees centigrade, like inside a computer case for example) without the batt and covers on for a minimum 12 hours (24 hours recommended) (if you put it in the computer case, the computer has to be on, since it produces the heat needed).
Once complete, insert the battery and reassemble and hope it works again
If you are prepared to mess with your phones internals a new digitizer can be had for about £60. Its the top most layer of the screen which means that it is the thing at the absolute back when you open up your phone because your phone opens from the back first. I think I saw a guide on XDA somewhere for this phone. Might want to try searching for it.
Adding to JSLEnterprises' post, remove everything that can be removed from the phone prior to putting it in a hot place. Thats the battery cover, bottom cover, battery, sim card and memory card. Just to be on the safe side. You dont want anything else to go wrong now.
Thanks a lot for your help guys
I found this YouTube link about disassemble desire hd
And I am going to order the touch screen from eBay then I will try to find someone to do it for me , last time I opend my phone I broken it
I dont want to do that again
First make sure to try the other method of heating up the phone. It may just work.
raze599 said:
First make sure to try the other method of heating up the phone. It may just work.
Click to expand...
Click to collapse
... and save you (the op) some money.
Hi mates. I have a weird problem. Just last night I am restoring a Nandroid Backup of VANIR ROM for geehrc, which DONT have a problem with my phone. When suddenly after booting and showing the lockscreen, the phone becomes unresponsive and after a few seconds, turns off. After that, It wont boot, even fastboot or recovery wont show up. Even tried the hard reset combo, but to no avail. Download mode works, but I have not tried to flash KDZ yet. Also when I plug in the charger, LG logo shows up then a blank grayish screen, then a battery icon with charging animation, plus a label that says 0% charging. I leave it for about 4 hours, thinking that the phone might just depleted the battery. But still it wont turn on. When I turn it on while plugged in, the LED blinks in red color. The blinking is continuous. What seems to be the problem? Is it hardware or software issue? Please help me guys! :crying:
Any help mates?
Im really loosing my hope reviving my device. Tried different methods from the web. I just flashed KDZ, but the phone keeps flashing the LG logo when plugged in. When I unplug the charger, and power on the phone, nothing happens! Damn. Can anyone give an insight on what might cause the problem? Thanks in advance!
Sorry to hear about your troubles! Honestly, I have no idea what could have caused this, but if I had the same issue, and nothing worked as you described, I would probably crack the phone open, disconnect the battery and just let it sit for a day or so. Then reconnect it, and try powering up again (might need to charge it first). Who knows whether it helps or not, but it definitely wouldn't hurt, and you don't seem to have a lot of options right now...
It's interesting that the download mode still works. The common wisdom says that you should be good after flashing stock KDZ, but your experience shows otherwise...
i've experienced it before. It happen due to your battery is out of charge. What i do is, i open the case, pullout battery and install back.
After that i charge the phone. And voila...charge is on..and my hp on too. :good:
kt-Froggy said:
Sorry to hear about your troubles! Honestly, I have no idea what could have caused this, but if I had the same issue, and nothing worked as you described, I would probably crack the phone open, disconnect the battery and just let it sit for a day or so. Then reconnect it, and try powering up again (might need to charge it first). Who knows whether it helps or not, but it definitely wouldn't hurt, and you don't seem to have a lot of options right now...
It's interesting that the download mode still works. The common wisdom says that you should be good after flashing stock KDZ, but your experience shows otherwise...
Click to expand...
Click to collapse
Thanks for your feedback! It's really weird. I have flashed 3 KDZ's already. From Original F180K to E975. Nothing. Other option I have aside cracking it open is returning it to the seller fro check up. But that's the last resort. I suspect something got "unglued" while I am using it. Since the device got really hot before it happened.
mark_vyz said:
i've experienced it before. It happen due to your battery is out of charge. What i do is, i open the case, pullout battery and install back.
After that i charge the phone. And voila...charge is on..and my hp on too. :good:
Click to expand...
Click to collapse
Will definitely try this. Thanks for the advice. How long should I remove the battery?
I just removed for a second and put it back. Most probably due to battery not fit. So i just retighten it.
Sent from my LG-E975 using xda app-developers app
MitoTakatori said:
Will definitely try this.
Click to expand...
Click to collapse
Should you go ahead with it, and in case you've never opened an OG before, just a little advice... It's not difficult, but you need to watch for a couple of things:
1. Make sure you remove the SIM tray BEFORE removing the back cover.
2. Start opening it from the bottom (after removing two screws), and work your way along the sides to the top. When putting it back together, go in reverse (top to bottom).
3. Be careful around the SIM slot and the buttons when prying the cover open -- it's easy to break a thin "bridge" on the side of the cover. Just don't push on those areas.
4. When putting the cover back on, it might be a bit tricky to hold power and volume buttons in position. The easy trick is to use a piece of scotch tape on the outside, so they don't fall in.
Good luck!
kt-Froggy said:
Should you go ahead with it, and in case you've never opened an OG before, just a little advice... It's not difficult, but you need to watch for a couple of things:
1. Make sure you remove the SIM tray BEFORE removing the back cover.
2. Start opening it from the bottom (after removing two screws), and work your way along the sides to the top. When putting it back together, go in reverse (top to bottom).
3. Be careful around the SIM slot and the buttons when prying the cover open -- it's easy to break a thin "bridge" on the side of the cover. Just don't push on those areas.
4. When putting the cover back on, it might be a bit tricky to hold power and volume buttons in position. The easy trick is to use a piece of scotch tape on the outside, so they don't fall in.
Good luck!
Click to expand...
Click to collapse
Thanks a lot for the tip! Actually I already opened it, only problem left is the battery. How can I remove it?
MitoTakatori said:
Thanks a lot for the tip! Actually I already opened it, only problem left is the battery. How can I remove it?
Click to expand...
Click to collapse
I wouldn't suggest actually removing the battery, unless you absolutely have to. It's mounted by a double-sided adhesive tape, so taking it out is a bit tricky. My idea was just to disconnect it. You need to undo two screws that secure the power connector, right below the camera flash. The screws are under the plastic tape, just peel it off. When you remove those screws, carefully pull the connector up. That's it. Check the contacts for any signs of damage or corrosion, and clean up as needed. When reconnecting it, push firmly to make sure it sits properly.
kt-Froggy said:
I wouldn't suggest actually removing the battery, unless you absolutely have to. It's mounted by a double-sided adhesive tape, so taking it out is a bit tricky. My idea was just to disconnect it. You need to undo two screws that secure the power connector, right below the camera flash. The screws are under the plastic tape, just peel it off. When you remove those screws, carefully pull the connector up. That's it. Check the contacts for any signs of damage or corrosion, and clean up as needed. When reconnecting it, push firmly to make sure it sits properly.
Click to expand...
Click to collapse
Nice tip again! Thanks! Now I don't have remove the battery. Only problem left is finding the small philips screw driver. Haha. Hoping that this solve the problem. If not, bye LGOG.
Thanks for all the helm mates! My LGOG is back in action!! Thanks again! :laugh: :good:
MitoTakatori said:
Thanks for all the helm mates! My LGOG is back in action!! Thanks again! :laugh: :good:
Click to expand...
Click to collapse
Great to hear! Congrats!
kt-Froggy said:
Great to hear! Congrats!
Click to expand...
Click to collapse
Now I am running Mokee's latest build. And will flash again VANIR. Thanks again guys. Thought I have to buy a new phone.
hi, same problem... but i must search at home if i can find a tool to open the screw... i only have - and + in this size and didnt work i miss my phone ((
ok. worked for me fine! Thanks!
now 80% battery instead of 0% very cool
and now i know how it looks into the phone very good working LG...
No more charge stuck on 0% sulation
when I plug in the charger, LG logo shows up then a blank grayish screen, then a battery icon with charging animation, plus a label that says 0% charging. I leave it for about 4 hours, thinking that the phone might just depleted the battery. But still it wont turn on.
SOLUTIONS:
1st take battery out of cell.
Leave in direct sun light for 1 hrs.
Clean battery pin with soft brush.
Charge battry manualy by Desktop charger about 2 to 3 hrs.
Put battery back in phone and start charging.
It will done Insha ALLAH.
ok so... the store broke my lcd while they were trying to remove the digitizer... and now i am looking at ebay on which lcd+touch assemlby to buy and i have a question. are the sony, acer and sharp lcd versions compatible with all one x mobos? i did some research and found that the sony version is the best (so they say)
and313 said:
ok so... the store broke my lcd while they were trying to remove the digitizer... and now i am looking at ebay on which lcd+touch assemlby to buy and i have a question. are the sony, acer and sharp lcd versions compatible with all one x mobos? i did some research and found that the sony version is the best (so they say)
Click to expand...
Click to collapse
Hi,
The Sony and Sharp are not compatible with each other( I've tried to replace one with the other), I've never come across the Acer LCD in Australia so I'm not sure. If you don't know how to tell the Sharp and Sony apart, the Sharp has Green backing on the flex cable, while the Sony is sort of orange with a few yellowish stripeson the back of the LCD flex cable. Sorry I couldn't find any of my photos which show the difference. I would recommend buying the LCD/digitizer combo and a separate midframe to mount it on, as it comes with new 3M adhesive, but you may also have to add a few TINY drops of instant adhesive, I say tiny as too much will press out under the digitizer and will show up, but I have found that without it the digitizer will lift from the frame eventually due to the tight fit of the frame in the rear shell of the HOX.
Hope you go ok!
---------- Post added at 06:45 PM ---------- Previous post was at 06:41 PM ----------
Sorry, just a bit of additional info, have also come across posts saying the colours of the LCD look washed out with the wrong LCD.
okhughes said:
Hi,
The Sony and Sharp are not compatible with each other( I've tried to replace one with the other), I've never come across the Acer LCD in Australia so I'm not sure. If you don't know how to tell the Sharp and Sony apart, the Sharp has Green backing on the flex cable, while the Sony is sort of orange with a few yellowish stripeson the back of the LCD flex cable. Sorry I couldn't find any of my photos which show the difference. I would recommend buying the LCD/digitizer combo and a separate midframe to mount it on, as it comes with new 3M adhesive, but you may also have to add a few TINY drops of instant adhesive, I say tiny as too much will press out under the digitizer and will show up, but I have found that without it the digitizer will lift from the frame eventually due to the tight fit of the frame in the rear shell of the HOX.
Hope you go ok!
---------- Post added at 06:45 PM ---------- Previous post was at 06:41 PM ----------
Sorry, just a bit of additional info, have also come across posts saying the colours of the LCD look washed out with the wrong LCD.
Click to expand...
Click to collapse
ok tnx for the info... and i was thinking i can just order whatever. i checked the panel_type in the last_kmsg and i found that i have the replacement screen for which nobody knows who makes it. but it is a warm panel so it probably is sony... but i have to rip it apart to be certain
Sent from my One X using Tapatalk
and313 said:
ok tnx for the info... and i was thinking i can just order whatever. i checked the panel_type in the last_kmsg and i found that i have the replacement screen for which nobody knows who makes it. but it is a warm panel so it probably is sony... but i have to rip it apart to be certain
Sent from my One X using Tapatalk
Click to expand...
Click to collapse
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
okhughes said:
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
Click to expand...
Click to collapse
tnx... you answered all i was wondering about really appreciated
edit: ok so i riped it apart again and its a sony. for anyone who is wondering what might happen if the wrong screen is attached to the mobo watch this
https://www.youtube.com/watch?v=DHdtgu4rbxI
and the store said: why you dont just buy the "original" for 40€.... god i hate such people
Sent from my One X using Tapatalk
okhughes said:
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
Click to expand...
Click to collapse
I replaced my screen, but I powered down when removing the screen, and putting the replacement in. Now neither will light up. How do you solve this?
There are no guarantees with this, but try pulling the battery out for a minute or two. then with the original screen in, boot up and let it get to the lock screen wait for the screen to sleep then press power button to wake up then again to sleep. when the screen is sleeping try changing over the screens and then press power button to wake again. this is assuming that the screen displays on startup, but even if it doesn't try this process anyway. if it doesn't work, try doing with the new screen back to the old screen after pulling the battery. I have only ever come across this once, but it wasn't from powering down during a screen change, but pulling the battery seemed to fix it.
okhughes said:
There are no guarantees with this, but try pulling the battery out for a minute or two. then with the original screen in, boot up and let it get to the lock screen wait for the screen to sleep then press power button to wake up then again to sleep. when the screen is sleeping try changing over the screens and then press power button to wake again. this is assuming that the screen displays on startup, but even if it doesn't try this process anyway. if it doesn't work, try doing with the new screen back to the old screen after pulling the battery. I have only ever come across this once, but it wasn't from powering down during a screen change, but pulling the battery seemed to fix it.
Click to expand...
Click to collapse
I tried that, didn't work. I think I know the problem now. after searching on multiple forums, I think it's the 220 coil. A lot of people have had a similar issue, and they say they've solved it by replacing the coil. What I want to know is, how I managed to short the coil in the span of a few minutes, despite having used the same screen as the cracked one.
It is possible to do, although they can go for no reason, I recommend taking it somewhere to get coil replaced, it is a very fiddly job and you need to have a steady hand and the right tools (hot air gun) although my father managed to do one with a standard soldering iron, although it wasn't the best job. you risk damaging other components also if they blow off the mainboard (if you can find them), worst case scenario is the display ic has gone - that one will have to be done by a professional.
what a sh!t phone
we tried to repare it 2 years ago.
but failed.
so i just the pieces to gether wanted to see if i can fix it.
still not lcd just touchscreen (and now im not sure if i even have touchscreen lol maybe i broke that to now not sure
anyway sucks i have a brand new lcd touchscreen with frame we bought back then. and its even the right screen a green flex cable like the original one and still noting so i guess i broke the 220 chip thing how dont know. but not sure if i can replace it sucks it was a good phone
is there any help a easy fix? or do i really need to soldern that chip i cant sell the phone since there is personal data on it contacts and pictures (i guess dont remembrer)
It may still be replaceable, if it's been sitting for 2 headed is the phone taking a charge? It needs to be on to change the screen. If it is charging and booting up, and the screen still won't work when being changed try doing a hard reset by holding the power and volume down button until it restarts - have had advice by someone who repairs phones for a living that this should reset what the phone is looking at for hardware and you should be able to do screen replacement. Failing that chances are it's going to be dead. Not much point in selling it these days as they aren't worth much these days. If the phone won't start the battery may be dead flat. The phone needs some voltage to run its charging firmware, you can try to get it charging by leaving on charge for 10 min or more, even if no charge light, then hold power/vol up/vol down at the same time to recalibrate the charge circuit, it may start to charge after this.
Let me know how it goes, I wouldn't spend too much time on it, unless it's now a project..
okhughes said:
It may still be replaceable, if it's been sitting for 2 headed is the phone taking a charge? It needs to be on to change the screen. If it is charging and booting up, and the screen still won't work when being changed try doing a hard reset by holding the power and volume down button until it restarts - have had advice by someone who repairs phones for a living that this should reset what the phone is looking at for hardware and you should be able to do screen replacement. Failing that chances are it's going to be dead. Not much point in selling it these days as they aren't worth much these days. If the phone won't start the battery may be dead flat. The phone needs some voltage to run its charging firmware, you can try to get it charging by leaving on charge for 10 min or more, even if no charge light, then hold power/vol up/vol down at the same time to recalibrate the charge circuit, it may start to charge after this.
Let me know how it goes, I wouldn't spend too much time on it, unless it's now a project..
Click to expand...
Click to collapse
ow volum down? okay will try that. but i think i killed it lol cause the charging light wont come on anymore lol
it was just a idea that poped up in my head, that maybe i can save it so i friend can use it but i think i will just trow it away lol or something will give it a shot and see. will report back
nvm it's dead it wont even boot lol. i think i burned sometime lol that little cable that onder the battery thats conects the botem part with the other fliped out 2 time and 3time it smeled burned lol nvm
Sounds like it may have shorted, a replacement is fairly cheap , just depends on how serious you are about spending money on it.
I forgot to mention that when calibrating charge circuit with power/vol up/vol down all held down at the same time, they need to be held down for at least 2 minutes.
okhughes said:
Sounds like it may have shorted, a replacement is fairly cheap , just depends on how serious you are about spending money on it.
I forgot to mention that when calibrating charge circuit with power/vol up/vol down all held down at the same time, they need to be held down for at least 2 minutes.
Click to expand...
Click to collapse
nvm i think i fried the cpu or something lol it wont turn on anymore.
i trew it in the bin
Probably the best result, it's probably cheaper to to buy a second hand one and also cause less aggravation when you can't work out why it won't work. You could always sell the replacement screen.
okhughes said:
Probably the best result, it's probably cheaper to to buy a second hand one and also cause less aggravation when you can't work out why it won't work. You could always sell the replacement screen.
Click to expand...
Click to collapse
dont think i will sell it i mean who would buy it? lol but guess i could try for like 20euro or 10 lol.
and have 2 batteries for 10 or 5 euro lol
have 3 backcovers also 2 white and 1 black.
we bought every thing to repaire it but yeah.
could maybe sell some **** but pff dont knopw. (its my oncles old phone will ask him (maybe sell every thing exept de motherboard)
That's what I'd do, try and sell it for parts minus the mainboard. If that doesn't work, put it away somewhere and if you come across a dead one cheap, swap the mainboards out (providing it has the same screen - that's a given). Good luck with whatever you decide to do. :good:
Hi there.
My Mother has a One V which she is really happy about. But recently she says that it has been draining the battery so fast. At first i didnt really believe it (you know old people and tech), and asked if she had charged it correctly. She then told me that the charging process was also quite strange.. She had plugged it in one night, and the phone displayed that it was charging.. Then 8 hours after, in the morning it had only charged 2% ! This doesnt happen all the time, but only some times.
Now she has given it to me and hope that i can fix it. At first im just going to factory reset it, even though i dont think that is the problem. But i have noticed that what she is telling me is true to some extend. I have had the phone sitting on the table all night. No simcard and no nothing.. It had only used about 5%, but as soon as i began using it, to take backup and prepare for the reset oh boy.. It uses 1% in merely seconds! Approx 26 seconds per 1%!
I think this is rather strange and im unsure if the battery is the problem.. Do you guys have any ideas ?
Oh and i have to say that the phone is running newest stock software. It has never been rooted or anything like that.
Well, the charger port is probably bad. My first htc one m8 and my droid incredible 2 both have weak ports on them from the factory. Send it in for warranty and say nothing < about a possible bad charging port if it still has warranty. And, if nothing Less try a brand new charger, and see if that one works and if it's loose when it's plugged in. If it Is loose with new charger it's a bad charger port.
Yeah this confuses me as well. It happens once every few months. The battery drains really fast and charging is extremely slow. The first time this happened my One V dropped from 100% to 27% in 20 minutes! And just like it randomly happens it randomly goes; battery consumption goes back to normal after a day or two.
A possible reason is the charger and USB cable that is used. My cable is worn out so that might be why charging is slow but it doesn't explain why the battery drains so fast even when the phone is disconnected from the charger. So the only reasonable explanation would be some hardware problems in the battery pack.
But this is all just me guessing... I don't know for sure.
tylerleo said:
Well, the charger port is probably bad. My first htc one m8 and my droid incredible 2 both have weak ports on them from the factory. Send it in for warranty and say nothing < about a possible bad charging port if it still has warranty. And, if nothing Less try a brand new charger, and see if that one works and if it's loose when it's plugged in. If it Is loose with new charger it's a bad charger port.
Click to expand...
Click to collapse
It could be the charger port. I tried cleansing it with a toothpick (heard dust could be the problem), but the problem persists
swhatevers said:
Yeah this confuses me as well. It happens once every few months. The battery drains really fast and charging is extremely slow. The first time this happened my One V dropped from 100% to 27% in 20 minutes! And just like it randomly happens it randomly goes; battery consumption goes back to normal after a day or two.
A possible reason is the charger and USB cable that is used. My cable is worn out so that might be why charging is slow but it doesn't explain why the battery drains so fast even when the phone is disconnected from the charger. So the only reasonable explanation would be some hardware problems in the battery pack.
But this is all just me guessing... I don't know for sure.
Click to expand...
Click to collapse
The problem here is that it happens every second time or so the phone is charged at the moment. But i have bought a new battery and will try and change it. Ill write here how it goes and if there is a improvement, so that you know where the problem relies if you are thinking about doing the same.
Same problem here. Every few months the battery drops from > 50% to 2% or so. This happens within some minutes and my phone gets really hot.
But normaly I use it with a 2 amp charger and I think this happens more often if I use chargers with 1 amp.
Edit: This happened for me with every rom I used.
I changed the battery two days ago, and i can already feel a huge improvement.. 8 hours ago i took it out from the charger. Data and Bluetooth has been on all day. Been browsing a little, and sent som SMS and stuff like that.. 65% now.
The conclusion must be that in my case at least, it was a battery hardware fault.
I'm also thinking about replacing my battery, was replacing it easy?
jonas2790 said:
I'm also thinking about replacing my battery, was replacing it easy?
Click to expand...
Click to collapse
Yes it was actually pretty easy. Although i have done it on my One S too, and that was even easier.
Some recommendations: Get your self a repair tool kit before you start. Everything has been so much easier for me after i got that. It is all the money worth it . This is what i got http://www.ebay.co.uk/itm/261399617620?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT <- They ship worldwide.
The battery i brought : http://www.ebay.co.uk/itm/321303229844?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
First i took the plate off at the bottom of the phone (the one where there behind is sim card and sd card). Unscrewed all six screws. Once done you can take all the plastic off the large plastic part (the one below the simcard and sd card when inserted, and covering everything behind the outer cover). This part is also taped/glued, but should not be a problem to get off.
After you have taken that off, use a pry tool to pry the plate open around the camera lens and flash (beware that this plate is also taped together. Unscrew the last screw behind.
Now comes the tricky part. You need another more solid pry tool to pry the lcd/board out from the front. Use the pry tool in between the screen and the cover of the phone, and all the way around. The LCD and board needs to come out from the phones front.
After that the battery becomes visible. There is nothing special to getting the plug out for it as far as i can remember and should just be pulled towards the battery to get it out. Battery is glue to the inside of the phone, but using the solid pry tool you should be able to get it out. If you order the battery i linked to, it comes with new 3M tape.
Heres a video showing it pretty good i think:
https://www.youtube.com/watch?v=gPasbSobzwA
Da9L said:
Yes it was actually pretty easy. Although i have done it on my One S too, and that was even easier.
Some recommendations: Get your self a repair tool kit before you start. Everything has been so much easier for me after i got that. It is all the money worth it . This is what i got http://www.ebay.co.uk/itm/261399617620?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT <- They ship worldwide.
The battery i brought : http://www.ebay.co.uk/itm/321303229844?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
First i took the plate off at the bottom of the phone (the one where there behind is sim card and sd card). Unscrewed all six screws. Once done you can take all the plastic off the large plastic part (the one below the simcard and sd card when inserted, and covering everything behind the outer cover). This part is also taped/glued, but should not be a problem to get off.
After you have taken that off, use a pry tool to pry the plate open around the camera lens and flash (beware that this plate is also taped together. Unscrew the last screw behind.
Now comes the tricky part. You need another more solid pry tool to pry the lcd/board out from the front. Use the pry tool in between the screen and the cover of the phone, and all the way around. The LCD and board needs to come out from the phones front.
After that the battery becomes visible. There is nothing special to getting the plug out for it as far as i can remember and should just be pulled towards the battery to get it out. Battery is glue to the inside of the phone, but using the solid pry tool you should be able to get it out. If you order the battery i linked to, it comes with new 3M tape.
Heres a video showing it pretty good i think:
https://www.youtube.com/watch?v=gPasbSobzwA
Click to expand...
Click to collapse
Aah so it was the battery pack after all!! Interesting to know.
Glad it worked out for you and thanks for the battery replacement links.
My One V is retired but since the battery is cheap I will buy one and replace it just in case I ever need the phone as backup.
Hey guys,
So i flooded my phone, dried it, left in rice for 2 days and now when i connect it to my charger the screen goes up after a minute or so but its not charging. My screen shows battery icon with a bolt inside and a zero below, or battery with a cable inside and zero below. Any idea what can i do to fix this? I can boot to bootloarder mode, but when I'm trying to boot to recovery/other modes it goes back to 'charging screen'.
Thanks in advance!
The battery is eeprom controlled so you probably damaged it when teaching the phone to swim. Flashing will do nothing for it.
Putting the phone in rice is a bad idea as it isn't as absorbent as you think. You should have left it over a radiator for a week or so to evaporate the water before even thinking about switching it on, but by then the damage was probably already done.
If it doesnt start working in week or so then expect it to be expensive to fix.
Beamed in by telepathy.
Not sure what eeprom is, but if its in the part below, then i could replace it myself with no problem. What are Your thougts? I know that more thing may be broken, but if it would go back to life i would be glad because I don't want to spend money on any new phone, maybe apart from S8/pixel but its expensive as hell.
https://e.allegroimg.com/original/0115f6/28e0dc9447338f8114880dfb6c1e
If i couldn't repair this bad boy then I would probably go with 6s, but I'm not sure if I want to make the transition to iOS.
Cheers and thanks for previous reply