ok so... the store broke my lcd while they were trying to remove the digitizer... and now i am looking at ebay on which lcd+touch assemlby to buy and i have a question. are the sony, acer and sharp lcd versions compatible with all one x mobos? i did some research and found that the sony version is the best (so they say)
and313 said:
ok so... the store broke my lcd while they were trying to remove the digitizer... and now i am looking at ebay on which lcd+touch assemlby to buy and i have a question. are the sony, acer and sharp lcd versions compatible with all one x mobos? i did some research and found that the sony version is the best (so they say)
Click to expand...
Click to collapse
Hi,
The Sony and Sharp are not compatible with each other( I've tried to replace one with the other), I've never come across the Acer LCD in Australia so I'm not sure. If you don't know how to tell the Sharp and Sony apart, the Sharp has Green backing on the flex cable, while the Sony is sort of orange with a few yellowish stripeson the back of the LCD flex cable. Sorry I couldn't find any of my photos which show the difference. I would recommend buying the LCD/digitizer combo and a separate midframe to mount it on, as it comes with new 3M adhesive, but you may also have to add a few TINY drops of instant adhesive, I say tiny as too much will press out under the digitizer and will show up, but I have found that without it the digitizer will lift from the frame eventually due to the tight fit of the frame in the rear shell of the HOX.
Hope you go ok!
---------- Post added at 06:45 PM ---------- Previous post was at 06:41 PM ----------
Sorry, just a bit of additional info, have also come across posts saying the colours of the LCD look washed out with the wrong LCD.
okhughes said:
Hi,
The Sony and Sharp are not compatible with each other( I've tried to replace one with the other), I've never come across the Acer LCD in Australia so I'm not sure. If you don't know how to tell the Sharp and Sony apart, the Sharp has Green backing on the flex cable, while the Sony is sort of orange with a few yellowish stripeson the back of the LCD flex cable. Sorry I couldn't find any of my photos which show the difference. I would recommend buying the LCD/digitizer combo and a separate midframe to mount it on, as it comes with new 3M adhesive, but you may also have to add a few TINY drops of instant adhesive, I say tiny as too much will press out under the digitizer and will show up, but I have found that without it the digitizer will lift from the frame eventually due to the tight fit of the frame in the rear shell of the HOX.
Hope you go ok!
---------- Post added at 06:45 PM ---------- Previous post was at 06:41 PM ----------
Sorry, just a bit of additional info, have also come across posts saying the colours of the LCD look washed out with the wrong LCD.
Click to expand...
Click to collapse
ok tnx for the info... and i was thinking i can just order whatever. i checked the panel_type in the last_kmsg and i found that i have the replacement screen for which nobody knows who makes it. but it is a warm panel so it probably is sony... but i have to rip it apart to be certain
Sent from my One X using Tapatalk
and313 said:
ok tnx for the info... and i was thinking i can just order whatever. i checked the panel_type in the last_kmsg and i found that i have the replacement screen for which nobody knows who makes it. but it is a warm panel so it probably is sony... but i have to rip it apart to be certain
Sent from my One X using Tapatalk
Click to expand...
Click to collapse
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
okhughes said:
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
Click to expand...
Click to collapse
tnx... you answered all i was wondering about really appreciated
edit: ok so i riped it apart again and its a sony. for anyone who is wondering what might happen if the wrong screen is attached to the mobo watch this
https://www.youtube.com/watch?v=DHdtgu4rbxI
and the store said: why you dont just buy the "original" for 40€.... god i hate such people
Sent from my One X using Tapatalk
okhughes said:
That's the only downside - having to pull phone apart to check which one you have. Also another tip, phone need to be on to change LCD's, boot phone up with it apart, then wake up with power button on old screen, then sleep with power button, change screens then wake up again. There are plenty of vids on youtube to help, if new screen doesn't activate, check flex cable is in square and all the way - have had this problem before also.
Click to expand...
Click to collapse
I replaced my screen, but I powered down when removing the screen, and putting the replacement in. Now neither will light up. How do you solve this?
There are no guarantees with this, but try pulling the battery out for a minute or two. then with the original screen in, boot up and let it get to the lock screen wait for the screen to sleep then press power button to wake up then again to sleep. when the screen is sleeping try changing over the screens and then press power button to wake again. this is assuming that the screen displays on startup, but even if it doesn't try this process anyway. if it doesn't work, try doing with the new screen back to the old screen after pulling the battery. I have only ever come across this once, but it wasn't from powering down during a screen change, but pulling the battery seemed to fix it.
okhughes said:
There are no guarantees with this, but try pulling the battery out for a minute or two. then with the original screen in, boot up and let it get to the lock screen wait for the screen to sleep then press power button to wake up then again to sleep. when the screen is sleeping try changing over the screens and then press power button to wake again. this is assuming that the screen displays on startup, but even if it doesn't try this process anyway. if it doesn't work, try doing with the new screen back to the old screen after pulling the battery. I have only ever come across this once, but it wasn't from powering down during a screen change, but pulling the battery seemed to fix it.
Click to expand...
Click to collapse
I tried that, didn't work. I think I know the problem now. after searching on multiple forums, I think it's the 220 coil. A lot of people have had a similar issue, and they say they've solved it by replacing the coil. What I want to know is, how I managed to short the coil in the span of a few minutes, despite having used the same screen as the cracked one.
It is possible to do, although they can go for no reason, I recommend taking it somewhere to get coil replaced, it is a very fiddly job and you need to have a steady hand and the right tools (hot air gun) although my father managed to do one with a standard soldering iron, although it wasn't the best job. you risk damaging other components also if they blow off the mainboard (if you can find them), worst case scenario is the display ic has gone - that one will have to be done by a professional.
what a sh!t phone
we tried to repare it 2 years ago.
but failed.
so i just the pieces to gether wanted to see if i can fix it.
still not lcd just touchscreen (and now im not sure if i even have touchscreen lol maybe i broke that to now not sure
anyway sucks i have a brand new lcd touchscreen with frame we bought back then. and its even the right screen a green flex cable like the original one and still noting so i guess i broke the 220 chip thing how dont know. but not sure if i can replace it sucks it was a good phone
is there any help a easy fix? or do i really need to soldern that chip i cant sell the phone since there is personal data on it contacts and pictures (i guess dont remembrer)
It may still be replaceable, if it's been sitting for 2 headed is the phone taking a charge? It needs to be on to change the screen. If it is charging and booting up, and the screen still won't work when being changed try doing a hard reset by holding the power and volume down button until it restarts - have had advice by someone who repairs phones for a living that this should reset what the phone is looking at for hardware and you should be able to do screen replacement. Failing that chances are it's going to be dead. Not much point in selling it these days as they aren't worth much these days. If the phone won't start the battery may be dead flat. The phone needs some voltage to run its charging firmware, you can try to get it charging by leaving on charge for 10 min or more, even if no charge light, then hold power/vol up/vol down at the same time to recalibrate the charge circuit, it may start to charge after this.
Let me know how it goes, I wouldn't spend too much time on it, unless it's now a project..
okhughes said:
It may still be replaceable, if it's been sitting for 2 headed is the phone taking a charge? It needs to be on to change the screen. If it is charging and booting up, and the screen still won't work when being changed try doing a hard reset by holding the power and volume down button until it restarts - have had advice by someone who repairs phones for a living that this should reset what the phone is looking at for hardware and you should be able to do screen replacement. Failing that chances are it's going to be dead. Not much point in selling it these days as they aren't worth much these days. If the phone won't start the battery may be dead flat. The phone needs some voltage to run its charging firmware, you can try to get it charging by leaving on charge for 10 min or more, even if no charge light, then hold power/vol up/vol down at the same time to recalibrate the charge circuit, it may start to charge after this.
Let me know how it goes, I wouldn't spend too much time on it, unless it's now a project..
Click to expand...
Click to collapse
ow volum down? okay will try that. but i think i killed it lol cause the charging light wont come on anymore lol
it was just a idea that poped up in my head, that maybe i can save it so i friend can use it but i think i will just trow it away lol or something will give it a shot and see. will report back
nvm it's dead it wont even boot lol. i think i burned sometime lol that little cable that onder the battery thats conects the botem part with the other fliped out 2 time and 3time it smeled burned lol nvm
Sounds like it may have shorted, a replacement is fairly cheap , just depends on how serious you are about spending money on it.
I forgot to mention that when calibrating charge circuit with power/vol up/vol down all held down at the same time, they need to be held down for at least 2 minutes.
okhughes said:
Sounds like it may have shorted, a replacement is fairly cheap , just depends on how serious you are about spending money on it.
I forgot to mention that when calibrating charge circuit with power/vol up/vol down all held down at the same time, they need to be held down for at least 2 minutes.
Click to expand...
Click to collapse
nvm i think i fried the cpu or something lol it wont turn on anymore.
i trew it in the bin
Probably the best result, it's probably cheaper to to buy a second hand one and also cause less aggravation when you can't work out why it won't work. You could always sell the replacement screen.
okhughes said:
Probably the best result, it's probably cheaper to to buy a second hand one and also cause less aggravation when you can't work out why it won't work. You could always sell the replacement screen.
Click to expand...
Click to collapse
dont think i will sell it i mean who would buy it? lol but guess i could try for like 20euro or 10 lol.
and have 2 batteries for 10 or 5 euro lol
have 3 backcovers also 2 white and 1 black.
we bought every thing to repaire it but yeah.
could maybe sell some **** but pff dont knopw. (its my oncles old phone will ask him (maybe sell every thing exept de motherboard)
That's what I'd do, try and sell it for parts minus the mainboard. If that doesn't work, put it away somewhere and if you come across a dead one cheap, swap the mainboards out (providing it has the same screen - that's a given). Good luck with whatever you decide to do. :good:
Related
I thought I'd share my experience with this, as I've seen posts in the past relating to a water damaged phone boot looping and I don't think I've seen a proper solution given.
First thing's first, this advice is in relation to a very specific type of boot looping. Nothing to do with rooting, or software bugs. This is boot looping that has come about as a result of water damage. It may not have been long, maybe a couple of seconds in the toilet or some brief rain exposure. Whatever it is, you know your phone has been exposed to some water and it has begun boot looping. There will be no way to get out of it, as the phone boots for 2/3 seconds max before looping all over again. Even when you go into recovery, same thing, automatically boot loops.
Most people, including the official HTC Service Centre, will tell you the motherboard is fried and needs replacement. Whilst it is possible that may be true, it isn't guaranteed. It's an easy way out for HTC, as they can charge you an extortionate price for a new motherboard and not have to bother going through the work of taking the phone apart to find out what is wrong.
The solution may be much simpler - the Power Flex Cable. This is a very small cable that goes along the top of your phone. WHen water damaged, this cable can become damaged, causing a constant boot loop. The reason being it constantly tells the phone the power button is on, causing a constant on/off cycle. In this instance the motherboard is fine and you can get a replacement Flex Cable for less than £5!
There is an easy way to tell whether the Flex Cable is the likely cause of your looping. When the phone is looping, hold down the down volume button only. Don't touch the power button. If your phone still goes into recovery (then loops again) then it is entirely possible your Flex Cable is damaged, not your motherboard.
Next step, order a Flex Cable (they are easy to find). When it arrives, you will need to open your phone (there are guides on YouTube for this), detach the motherboard and replace the Flex Cable. An advance warning, this isn't easy and you have to be extremely careful. One bad move and your phone is history. The motherboard is delicate. If you look around the internet you will find guides which show how the HTC One X is configured. Note that the Flex Cable is behind the motherboard and quite awkward to get off. I would post a couple of links but as a new member I'm not allowed! PM me and I'm happy to share some helpful links though.
You'll know quickly if this has worked. When connecting your phone it will no longer loop. Let it charge for a little while, then power on and hope for the best. If the Flex Cable was the problem your phone will reboot, and you will be able to use it and get your data off.
Note that water damage can have long lasting effects on a mobile phone. Whilst this may solve the problem for a while, it's entirely possible your phone will fail at some point down the line. Prepare for that and make sure you back up accordingly. The above advice may give you a lifeline in getting data off your phone, though, and being able to use it for a little longer. I know that when I was looking around the net I only found this advice by chance, and I think it was on a non-phone related forum. This advice may exist on the forum somewhere but if so it isn't so easy to find. I hope somebody may come across this topic when trying to fix their water damaged phone and find it is the solution.
Good luck!
Same symptoms, but no water damage
Hey man,
Thanks a ton for your post. I have the same issue, as in it won't stop booting at all. However, mine didn't happen because of water damage, but when I tried to do a factory reset (the phone was only on 5% charge so I'm not sure if that screwed it up). Do you think it could still be solved with a flex cable? I tried holding just the volume button down, and it does go into the bootloader so it seems pretty much exactly like what you have described!
Cheers
My only experience with replacing the flex cable comes from water damage, I'm not sure whether a software fault (as this appears to be) could have any effect on the cable itself!
When you get into the bootloader screen, does it just cycle all the way through to fastboot without allowing you to select any other options before rebooting? If so it would suggest your phone thinks the power button is constantly pushed down, which is suggestive of a power flex cable fault.
These cables are very cheap to buy, so if you aren't able to do anything else with the phone it's definitely worth a shot, even if it doesn't work. Just remember that opening the phone voids your warranty, and be careful if you do attempt it, as the insides of the One X are quite delicate. It would be very easy to break something!
de4life said:
My only experience with replacing the flex cable comes from water damage, I'm not sure whether a software fault (as this appears to be) could have any effect on the cable itself!
When you get into the bootloader screen, does it just cycle all the way through to fastboot without allowing you to select any other options before rebooting? If so it would suggest your phone thinks the power button is constantly pushed down, which is suggestive of a power flex cable fault.
These cables are very cheap to buy, so if you aren't able to do anything else with the phone it's definitely worth a shot, even if it doesn't work. Just remember that opening the phone voids your warranty, and be careful if you do attempt it, as the insides of the One X are quite delicate. It would be very easy to break something!
Click to expand...
Click to collapse
I had to replace my power flex cable when I was changing my battery as I accidentally snapped it.
Kahun said:
I had to replace my power flex cable when I was changing my battery as I accidentally snapped it.
Click to expand...
Click to collapse
It's very easy to do, the flex cable is a fragile piece. There are quite a few parts inside the HOX which could easily snap, which is why I always urge a lot of caution when opening the phone up!
de4life said:
I thought I'd share my experience with this, as I've seen posts in the past relating to a water damaged phone boot looping and I don't think I've seen a proper solution given.
First thing's first, this advice is in relation to a very specific type of boot looping. Nothing to do with rooting, or software bugs. This is boot looping that has come about as a result of water damage. It may not have been long, maybe a couple of seconds in the toilet or some brief rain exposure. Whatever it is, you know your phone has been exposed to some water and it has begun boot looping. There will be no way to get out of it, as the phone boots for 2/3 seconds max before looping all over again. Even when you go into recovery, same thing, automatically boot loops.
Most people, including the official HTC Service Centre, will tell you the motherboard is fried and needs replacement. Whilst it is possible that may be true, it isn't guaranteed. It's an easy way out for HTC, as they can charge you an extortionate price for a new motherboard and not have to bother going through the work of taking the phone apart to find out what is wrong.
The solution may be much simpler - the Power Flex Cable. This is a very small cable that goes along the top of your phone. WHen water damaged, this cable can become damaged, causing a constant boot loop. The reason being it constantly tells the phone the power button is on, causing a constant on/off cycle. In this instance the motherboard is fine and you can get a replacement Flex Cable for less than £5!
There is an easy way to tell whether the Flex Cable is the likely cause of your looping. When the phone is looping, hold down the down volume button only. Don't touch the power button. If your phone still goes into recovery (then loops again) then it is entirely possible your Flex Cable is damaged, not your motherboard.
Next step, order a Flex Cable (they are easy to find). When it arrives, you will need to open your phone (there are guides on YouTube for this), detach the motherboard and replace the Flex Cable. An advance warning, this isn't easy and you have to be extremely careful. One bad move and your phone is history. The motherboard is delicate. If you look around the internet you will find guides which show how the HTC One X is configured. Note that the Flex Cable is behind the motherboard and quite awkward to get off. I would post a couple of links but as a new member I'm not allowed! PM me and I'm happy to share some helpful links though.
You'll know quickly if this has worked. When connecting your phone it will no longer loop. Let it charge for a little while, then power on and hope for the best. If the Flex Cable was the problem your phone will reboot, and you will be able to use it and get your data off.
Note that water damage can have long lasting effects on a mobile phone. Whilst this may solve the problem for a while, it's entirely possible your phone will fail at some point down the line. Prepare for that and make sure you back up accordingly. The above advice may give you a lifeline in getting data off your phone, though, and being able to use it for a little longer. I know that when I was looking around the net I only found this advice by chance, and I think it was on a non-phone related forum. This advice may exist on the forum somewhere but if so it isn't so easy to find. I hope somebody may come across this topic when trying to fix their water damaged phone and find it is the solution.
Good luck!
Click to expand...
Click to collapse
Thanks. I've already taken the back off and noticed some broken bits of plastic...from the back....but I did notice a bit of ribbon that looked a bit screwed up....I'm gonna take it to the gizmo wizard to fix once I buy a new power flex cable.
Good luck!
Another thing to try
de4life said:
Good luck!
Click to expand...
Click to collapse
Old thread I know but thought it was worth adding that with a water damaged phone the issues can result from the fact that tap water contains minerals which can leave a conductive residue when it dries - can change resistances, cause shorts etc. What I've done previously is used isopropyl alcohol (tape head cleaning fluid) with a toothbrush on the motherboard. Brought a phone back to life. This removes the mineral deposits and cleans everything. Had to remove the metal covers from the mobo first though. If a phone is basically dead or not working right after water damage then it's worth a go. As de4life says, just need to be super careful on the HOX with all the delicate ribbon cables.
Indeed, the phone should be thoroughly clensed if possible to wipe out any corrosive liquids left behind from the water (especially if it's dropped in an ocean). The effects of corrosion can be very slow and potentially last for months.
M8 please reply to this all the flex cables that I found are 40$+ can you give me a link for one as you stated that would cost 5 pounds
It worked
It worked! I replaced the power flex cable with a spare one on my HTC One X, previously damaged by being sucked by my one year old son - water damage.! It worked!
Many thanks to you man!
IamNewBee said:
Many thanks to you man!
Click to expand...
Click to collapse
Wondering if this is the right cable?
http://www.ebay.com/itm/New-Power-O...972183?hash=item27d4be6597:g:n6AAAOSw9GhYbb-y
Thanks!
Thank you!
de4life said:
I thought I'd share my experience with this, as I've seen posts in the past relating to a water damaged phone boot looping and I don't think I've seen a proper solution given.
First thing's first, this advice is in relation to a very specific type of boot looping. Nothing to do with rooting, or software bugs. This is boot looping that has come about as a result of water damage. It may not have been long, maybe a couple of seconds in the toilet or some brief rain exposure. Whatever it is, you know your phone has been exposed to some water and it has begun boot looping. There will be no way to get out of it, as the phone boots for 2/3 seconds max before looping all over again. Even when you go into recovery, same thing, automatically boot loops.
Most people, including the official HTC Service Centre, will tell you the motherboard is fried and needs replacement. Whilst it is possible that may be true, it isn't guaranteed. It's an easy way out for HTC, as they can charge you an extortionate price for a new motherboard and not have to bother going through the work of taking the phone apart to find out what is wrong.
The solution may be much simpler - the Power Flex Cable. This is a very small cable that goes along the top of your phone. WHen water damaged, this cable can become damaged, causing a constant boot loop. The reason being it constantly tells the phone the power button is on, causing a constant on/off cycle. In this instance the motherboard is fine and you can get a replacement Flex Cable for less than £5!
There is an easy way to tell whether the Flex Cable is the likely cause of your looping. When the phone is looping, hold down the down volume button only. Don't touch the power button. If your phone still goes into recovery (then loops again) then it is entirely possible your Flex Cable is damaged, not your motherboard.
Next step, order a Flex Cable (they are easy to find). When it arrives, you will need to open your phone (there are guides on YouTube for this), detach the motherboard and replace the Flex Cable. An advance warning, this isn't easy and you have to be extremely careful. One bad move and your phone is history. The motherboard is delicate. If you look around the internet you will find guides which show how the HTC One X is configured. Note that the Flex Cable is behind the motherboard and quite awkward to get off. I would post a couple of links but as a new member I'm not allowed! PM me and I'm happy to share some helpful links though.
You'll know quickly if this has worked. When connecting your phone it will no longer loop. Let it charge for a little while, then power on and hope for the best. If the Flex Cable was the problem your phone will reboot, and you will be able to use it and get your data off.
Note that water damage can have long lasting effects on a mobile phone. Whilst this may solve the problem for a while, it's entirely possible your phone will fail at some point down the line. Prepare for that and make sure you back up accordingly. The above advice may give you a lifeline in getting data off your phone, though, and being able to use it for a little longer. I know that when I was looking around the net I only found this advice by chance, and I think it was on a non-phone related forum. This advice may exist on the forum somewhere but if so it isn't so easy to find. I hope somebody may come across this topic when trying to fix their water damaged phone and find it is the solution.
Good luck!
Click to expand...
Click to collapse
Thank you very much for typing this out! My Google Pixel OG (2016), which was made by HTC, experienced the exact same problem. I have just fixed it by replacing the power flex cable like you suggested.
lazinase said:
Thank you very much for typing this out! My Google Pixel OG (2016), which was made by HTC, experienced the exact same problem. I have just fixed it by replacing the power flex cable like you suggested.
Click to expand...
Click to collapse
I was surprised to get a notification for this old thread! I'm glad this worked for you. I had no idea HTC used the same design for the original Pixel.
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Fycola123 said:
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Click to expand...
Click to collapse
Hi,
Only thing I can think of is that somehow it has damaged the cable from the touchscreen or the tiny wires that feed into the cable without damaging the screen. I came across a brand new screen I was replacing once for someone that had a similar problem where the bottom left hand corner wouldn't respond to touch unless there was firm pressure on the screen to create contact, and this was a brand new screen. It could also be that the touchscreen connector needs to be pushed back onto the board if it's come a bit loose.
If this is the problem, you can fix it by yourself although I'd have a good look around youtube, there are heaps of DIY videos of how to replace screens. If you do go down this path I recommend you replace the touchscreen/LCD/LCD frame in one go, as it's generally already pre- assembled the only thing here is that there are 3 brands of LCD's HTC used with the phone and they aren't all compatible, and you can only tell by pulling down your phone and looking at the LCD flex cable colours, and the other thing is that the screens that are available aren't always the same quality as the original. If this sounds to hard your best bet is to take it somewhere and diagnose the problem just in case it's something else
Hey all, so I just replaced the screen (followed the great guide on this site) and now I'm getting some odd behavior when trying to boot.
The power button is completely unresponsive. When I plug the phone into power, the LG screen comes up for ~3 seconds, as normal. The LED is flashing thru all the colors per the usual as well. Then the screen goes black for another 3 seconds, all the while the LED flashing. Then LG pops up again just for a moment, then to the normal phone-is-off-but-charging screen, with the LED flashing red.
Really don't know what to make of this. I had it rooted with a one-click root from here. The only changes were deleting stock apps and enabling the front touch keys (but never had an issue with it booting after this, I did that at least a week ago). Also my PC recognizes that something is plugged in, so I guess that's good.
Thoughts?
Update: tried booting into recovery mode, I held the buttons for much longer than normal to no response. As soon as I let go, I get the LG screen. Then black. Then LG. Then an unusually long AT&T screen, then it booted. Now the power button works as it should, and it boots in that same odd fashion. And it seems that I can not go into recovery. Yikes.
I'd be fine with that except I have a dead zone across the lower portion of the screen, it's about a half inch tall and about covers the asdfgh... row of the keyboard. Weirdly if I start pressing on any other key and then swipe to any area in the "dead" zone it WILL register, as in, I can select the S key, normally in the dead zone, but swiping to it from a working area. Will try soaking the mobo in alcohol and swabbing the digitzer connector with a q-tip. Any other thoughts?
Update 2: I tried cleaning the contacts of the digitzer connection- both the end of the cable and the motherboard connection- with rubbing alcohol. Reassembled, and we're back to square one. Power button unresponsive, when plugged in I'll get the LG screen, then black, then the LG screen will flash and I'll get the chargining screen. But now, trying to boot into recovery mode does nothing. So then I soaked the mobo in alcohol, and cleaned ALL the contacts and ribbon cables on the frame. Reassembled, no change. I really hope someone sees this, as I'm at he end of my tech know-how. Tonight I'll try to reconnect my old touchscreen and see what happens. Maybe the new one is just defective? But you'd think the phone would still turn on...
God I hope somebody sees this. I feel like a complete nut talking to myself.
mityman50 said:
Hey all, so I just replaced the screen (followed the great guide on this site) and now I'm getting some odd behavior when trying to boot.
Click to expand...
Click to collapse
Okay sounds like a hardware issue with the power button being unresponsive. I would take the device apart look around all connections of the power button and look for any hair line cracks or dirty, sticky, grimmy connections. Try cleaning upall that stuff, while there I would look at the digitizer and clean that up. When done flash a new rom with the LG flash tool, allow boot and reboot normally several times before testing. I hope this helps I am new to the phone and have yet to get my repair kit for it so I will not know much more about it till I get into it myself. Hair line cracks can be easily fixed as long as its on the sadder areas. Just re sadder it
---------- Post added at 09:01 PM ---------- Previous post was at 08:34 PM ----------
Now for the weird flashing on and off booting mine does this as well but all functions regardless are working flawlessly. My phone will need serious structural repairs but nothing I can't do just had a horrible owner. Definitely worth the trouble this thing runs so smooth better than any other I have used and it will continue to hold for a couple years cause of the power behind it. I wouldn't worry about the booting flashing like that I'm just thinking it does this to show it has been tampered with.
Sent from my LG-E980 using XDA Free mobile app.
Hey man thanks for your reply. Reminded me to update this for anyone else who finds it.
So the new screen was definitely defective. The one time I managed to get it on there was a dead spot. I sent it back, a replacement is on its way.
Now the good news- I realized why my phone wouldn't boot. Turns out that when removing the motherboard, the top part of it got a little... bent. Nothing bad, nothing permanent, but when I mounted back onto the housing, the top part of it had a tendency to stick up a little bit. Well if you follow the small ribbon cable off the power button, it leads to two gold contacts. Sure enough on on the bottom side of the motherboard there are two nodes that would press against the contacts.
Basically, the power button wasn't even connected to the board.
So I actually put the whole thing together, screws and all, and with that, the motherboard sits snugly as it should and the button works fine.
Right now my phone is some sort of hacked up zombie, with a cracked up screen, an upper-left corner that's completely decimated/missing, and no adhesive to hold it together. Hopefully the screen makes it here soon!
Oh and I agree totally, this is the smoothest and most reliable Android I've owned, better than the Evo 3D (which I quite liked) and a GS3 (meh, it got very unreliable after a year). I'm happy the screen replacement is cheap and easy so I can keep this thing for at least another year.
Cool glad it worked out for you or hopefully will. Can you do me a solid once your screen comes in and if it replaced well all working that is could you post the site you got it on or pm me with it. I am here tons of issues with defective screens. Would like to have a reliable market to shop from.
Sent from my LG-E980 using XDA Free mobile app
Fant0m3 said:
Cool glad it worked out for you or hopefully will. Can you do me a solid once your screen comes in and if it replaced well all working that is could you post the site you got it on or pm me with it. I am here tons of issues with defective screens. Would like to have a reliable market to shop from.
Sent from my LG-E980 using XDA Free mobile app
Click to expand...
Click to collapse
I have never had a bad part for any kind of phone from Wholesale Gadget Parts in Bixby, OK (Tulsa area). I found them on Amazon and originally ordered because they were close and I was in a hurry. I kept ordering because they get it right. I have about a 50/50 success rate with phone parts off other sellers on Amazon. If you buy cheap, expect a high failure rate.
Glass and digitizer for G Pro is about $18 before shipping and any applicable tax.
Yes, like it turned itself off but it did not go off as I was still getting audible email notifications. Tried everything speaking with Google support and then even Asus support who told me to go to their website and fill in an RMA form. This unit is 13 months old-out of warranty. There is nothing on the form relevant to the nexus to fill in so you cannot continue with it. So I am stuck right now and do not know what to do if anything. Any help would be appreciated.
claypoole said:
Yes, like it turned itself off but it did not go off as I was still getting audible email notifications. Tried everything speaking with Google support and then even Asus support who told me to go to their website and fill in an RMA form. This unit is 13 months old-out of warranty. There is nothing on the form relevant to the nexus to fill in so you cannot continue with it. So I am stuck right now and do not know what to do if anything. Any help would be appreciated.
Click to expand...
Click to collapse
Normally, 3 things can go wrong:
1. The cable is not connected properly. This could be caused by any impact. You take off the back cover and reseat it. It's the amber cable that runs the length of the battery. Be sure to check both ends. The one on the motherboard's end is in plain sight. The other end is hidden beneath the daughter board at the bottom of the tab, so you need to remove it to inspect the connection.
2. The backlight which illuminates the display went out. You can check this by turning the tab on and taking the tab to a dark room and shine a flashlight on the screen. If you can see the icons or the boot page, the back light is bad. The bad news is that you'd have to remove the lcd/touchscreen unit to replace the backlight. 10 times out of 10, when you do this on an original tab, you will break the touchscreen. Since it's glued to the lcd with LOCA (liquid optically clear adhesive), you will have to separate them, fix the backlight, buy a new touchscreen, then reassemble the whole thing. Most people would find it simpler to just buy a new lcd/touchscreen combo. If you're game though, I can give you an lcd back with a working backlight strip.
3. The video circuit on the motherboard went belly up. To test this, you need a micro usb to HDMI adapter like the one here , and a newer lcd TV. If nothing shows on your TV, the GPU is probably dead, in which case the only practical solution is to replace the motherboard since it's impossible to replace the GPU at home.
Good luck.
graphdarnell said:
Normally, 3 things can go wrong:
1. The cable is not connected properly. This could be caused by any impact. You take off the back cover and reseat it. It's the amber cable that runs the length of the battery. Be sure to check both ends. The one on the motherboard's end is in plain sight. The other end is hidden beneath the daughter board at the bottom of the tab, so you need to remove it to inspect the connection.
2. The backlight which illuminates the display went out. You can check this by turning the tab on and taking the tab to a dark room and shine a flashlight on the screen. If you can see the icons or the boot page, the back light is bad. The bad news is that you'd have to remove the lcd/touchscreen unit to replace the backlight. 10 times out of 10, when you do this on an original tab, you will break the touchscreen. Since it's glued to the lcd with LOCA (liquid optically clear adhesive), you will have to separate them, fix the backlight, buy a new touchscreen, then reassemble the whole thing. Most people would find it simpler to just buy a new lcd/touchscreen combo. If you're game though, I can give you an lcd back with a working backlight strip.
3. The video circuit on the motherboard went belly up. To test this, you need a micro usb to HDMI adapter like the one here , and a newer lcd TV. If nothing shows on your TV, the GPU is probably dead, in which case the only practical solution is to replace the motherboard since it's impossible to replace the GPU at home.
Good luck.
Click to expand...
Click to collapse
Did anyone else read this response and want to hit the edit button, and then type in huge letters "Time to buy a new Nexus!"
Thank you for your detailed reply. I checked the cable from the MB at both ends. Seems OK on the connections. I am unable to turn on the tab to check the backlight. That's about as far as I can go with it at this point. I am thinking that this tab is toast and to make matters worse, the abominably bad Asus customer service. I am considering replacing this with a Samsung and be done with it.
claypoole said:
Thank you for your detailed reply. I checked the cable from the MB at both ends. Seems OK on the connections. I am unable to turn on the tab to check the backlight. That's about as far as I can go with it at this point. I am thinking that this tab is toast and to make matters worse, the abominably bad Asus customer service. I am considering replacing this with a Samsung and be done with it.
Click to expand...
Click to collapse
Hey, don't lose hope! Samsung is not any better specs or quality-wise (especially the display). If you're gonna butcher the thing anyway, might as well find out. I was gonna suggest to lend you a used lcd for you to test, but I realize people for some reason are extremely wary of gratuitous offers so I won't. But if you value it, try to get a screen with a good lcd but broken digitizer on Ebay. They wouldn't cost more than 15 bucks. Once you can determine it's not the motherboard, we can go from there. I can guide you on the replacement part if you want. I'm just a hobbyist, but I have messed around with this thing enough to tell.
Graph, you are kind to offer. I also have noticed that the glass has a few cracks in it as well. At this point, I can't turn it on. It seems like when I punch the on button in there is extremely little movement if at all. So I don't know if it is still on which I don't this it is or it shut itself off. When it was black screen and on, I was getting my email notifications audibly but since yesterday-none. I am not looking to spend big bucks on these things as essentially all I do mostly is use for reading. I do want to stick with android if I replace this. I know samsung does not have as good resolution but seems to get good reviews from users.
Anybody know where i could find the daughter board? My pixel XL ended up the in the pet bowl for 5 seconds. The rest of the phone works, but that board is not working. (No sounds, charging, or vibration) I sent the phone to UbreakIfix (supposedly they get oem parts) They said they tried replacing it and it didn't work. When I get the phone back from them, I will look at my phone to see if they even looked at it. I don't really want to pay the deductible of 200 and wait forever for a replacement from Asurion. Plus it is a verizon model, so most likely it will come with 7.1.1.
Update on the water damaged pixel xl from my post in the general thread:
"I have good news, I don't think the company I sent the phone to did jack. The phone didn't look any different, even though they did a lot of work to the phone. I got the phone back today, I plugged it in and still nothing. I wanted to see for myself what was inside (ifixit wasn't enough). I tore it apart and did not see any corrosion. The water sensor is visible when you take off the screen through the mid-frame. It was 3/4 tripped (1/4 was still white). So I tried unplugging and re-plugging everything in. I plugged the charger in and the screen lit up with 0%. The phone didn't charge up after a while, even with the screen still on. I did the water recovery on the board on the bottom with the charge port. Next I only got a blinking red light and no screen lit up. I let it sit for 15 min. Tried turning it on, nothing. So I help down the power button while unplugging and plugging it in multiple times, and voila it turned on! Everything works on the phone! So I put it back together, put 3M industrial adhesive, and it is currently under clamps.
TL;DR I did my own water recovery on the phone, and I got it working!"
I did not find a replacement board, so much for modular replacement parts. I can only find screens. It doesn't help that the phone is so back ordered. Maybe when things tone down, we will see replacement parts.
chapelfreak said:
Update on the water damaged pixel xl from my post in the general thread:
What is involved with water recovery on the board? Just curious Case it ever happens to me
Click to expand...
Click to collapse
chapelfreak said:
Update on the water damaged pixel xl from my post in the general thread:
"I have good news, I don't think the company I sent the phone to did jack. The phone didn't look any different, even though they did a lot of work to the phone. I got the phone back today, I plugged it in and still nothing. I wanted to see for myself what was inside (ifixit wasn't enough). I tore it apart and did not see any corrosion. The water sensor is visible when you take off the screen through the mid-frame. It was 3/4 tripped (1/4 was still white). So I tried unplugging and re-plugging everything in. I plugged the charger in and the screen lit up with 0%. The phone didn't charge up after a while, even with the screen still on. I did the water recovery on the board on the bottom with the charge port. Next I only got a blinking red light and no screen lit up. I let it sit for 15 min. Tried turning it on, nothing. So I help down the power button while unplugging and plugging it in multiple times, and voila it turned on! Everything works on the phone! So I put it back together, put 3M industrial adhesive, and it is currently under clamps.
TL;DR I did my own water recovery on the phone, and I got it working!"
I did not find a replacement board, so much for modular replacement parts. I can only find screens. It doesn't help that the phone is so back ordered. Maybe when things tone down, we will see replacement parts.
Click to expand...
Click to collapse
Where did you find replacement screens available for sale? I know there is a 3rd party google uses to actually do the repair but I haven't seen the screens available for sale anywhere yet?
aholeinthewor1d said:
Where did you find replacement screens available for sale? I know there is a 3rd party google uses to actually do the repair but I haven't seen the screens available for sale anywhere yet?
Click to expand...
Click to collapse
The third party is uBreakiFix, they get oem parts, and they said it will not void your warranty. They couldn't get my phone going, so I took it into my own hands and got it working. They were confused how I got it working (the person on the phone) and they couldn't. uBreakiFix is 149.99 to replace the screen, and they send you a mailing slip for free to mail the phone in. I am not affiliated with them at all, I am a miniority owner/repair tech of a repair shop where I live. You can find them all over the web. My company uses fixez.com to order screens from. They obviously aren't oem, but we have had good luck with screens from them for different devices we have fixed (samsung, apple, htc, ect).
If you want oem I'd send it in to ubreakifix to get repaired. If not here is example of two sites:
https://www.fixez.com/store/google/google-pixel-xl/google-pixel-xl-display-assembly-black
http://www.ebay.com/sch/i.html?_fro...Xpixel+xl+lcd.TRS2&_nkw=pixel+xl+lcd&_sacat=0
mac796 said:
chapelfreak said:
Update on the water damaged pixel xl from my post in the general thread:
What is involved with water recovery on the board? Just curious Case it ever happens to me
Click to expand...
Click to collapse
Basically you have to do what ifixit's tear down does. I think they might have been a bit too hasty or used too much heat getting the screen off since they broke the screen. Once I got the screen off, it wasn't too hard to get all the screws out and the mid frame off. The power and volumne flex come up with the mid frame. I cleaned the motherboard connection and cleaned the whole board on bottom with some 99.9% isopropyl alcohol and a tooth brush. After all the alcohol dried up, I hooked the flex from the mobo to the charge port board and plugged it in.
Click to expand...
Click to collapse