I love the auto screen brightness setting when using power saving mode but I don't like that the soft keys are no longer light. Can the soft key backlughts be enabled?
Related
Hi
My XDA IIs is wrking fine except that often when switching back on the backlight is minimised. When I adjust the backlight settings on battery it is OK, but then once again reverts to the slider being minimised upon restart.
The turn off backlight if device not used for is unchecked.
The turn on backlight when a button is pressed is checked.
The power setting is turn off device if not used for 2 minutes.
Any ideas.
Many thanks
Rod King
when you say "restart" are you poking the stylus in the reset hole or holding down the power button?
holding down the power button turns off the backlight, holding it down again, turns it back on
I have had this problem when I changed the backlight setting. Try going into the Backlight properties under the "Battery Power" tab. Place a check in "Turn on backlight when a button is pressed or the screen is tapped."
Then go to the "Button Lock" properties and choose "Lock all buttons except Power button" so that only the power button will wake your unit. If this don't solve it, then it may be a software you installed.
hope that helps..
Thanks for reading the post...I am very frustrated with this device and want to see if ANYONE can help me...
First, the power button...I can turn the device on, but it will not turn the device off...it only lights on the screen backlight or turns the screen backlight off...I can't power it off, no matter how long I press it for...Therefore I have to take tha battery out to power off...which is not good for data!
Second, the backlight on battery level resets itself to 0 (thus a near black screen until I can get it into a bright light and go in and activate the backlight on battery level to 1 at least) Why is this doing this, and it only happens every 5-6 times I power the device on...
Thanks for your help everyone!!!
As far as I know, there is no way to actually power off the JasJar/Universal - it's always in a standby mode unless you pull the battery.
Not sure about your other issue though - sorry.
Cheers,
Steve.
It resets the backlight settings probably because it has "forgotten" your previous settings due to the way you "power off" your Universal. It is a phone, not a laptop, so it only goes into standby mode.
Sounds like you are pressing and holding down the power button for too long. To turn on/off the device, just tap on the power button once and don't hold it down. Hope that helps! :wink:
is there a registry edit so that when i press the turn backlight button off (power button) so it locks into s2u2??
I don't know but I have it so that S2U2 activates when the backlight turns back on again. So I press the power button to switch it on, and S2U2 loads.
This is probably better for battery life so that you don't have the app running whenever you're not using the phone.
There is a setting to lock when the backlight turns off.
Have you actually looked in S2U2 settings to check this yet?
I withdraw my question.
When trying to set my Desire into standby mode by pressing the power button it switches on the display again at once. Even trying some other ROMs doesn't fix the problem.
Does anyone know why and has a solution for this problem?
Your power button might be damaged. Look for a screen lock app on the playstore and use it to put your device to sleep instead of using the power button.
via xda app
Same with such an app. Display comes back again.
Volume button sems to be active too cause after display comes back sometimes the volume setting "sound " appears .
No idea or wrong category here?
Did you activate a "volume key wake" that enables volume keys to wake up the device ?
On my Desire these buttons can be a bit hard to push sometimes, maybe you have the opposite effect ?
Edit : such settings may be found in the "display" section of the settings tab
No, even several other Roms didn´t fix the problem.
Also watched: the volume funktion seems to be active in background too cause after almost every "wake up" the ring volume setting is displayed for 1 second.
Seems to be a hardware problem but the Desire did not fall down or sth like that...
When choosing trackball or volume key for wakeup in the settings, the display always switches on and off. Power button still causes a hard reset.
When watching some show with XBMC the soft keys stay continually on , I need to know if an Xposed module or something else can do the trick to turn them off?
Are you on stock ROM or cm11? For stock just turn power saving on and it should be off. For cm11 there's an option for that in settings, buttons,backlight
Are you on stock ROM or cm11? For stock just turn power saving on and it should be off. For cm11 there's an option for that in settings, buttons,backlight<br/>
I am on stock that was easy thanks, just wondering what else this power saving turn off?
Why don't you just turn off the lights in the settings? It's under Display.