[Q] Need N7 2013 LTE USB Charging Board (P/N 60NK0090-SU1030) - Nexus 7 (2013) Accessories

While replacing my screen I accidentally damaged the ribbon connector on the Charging Board. Help needed getting another board or ideas on how to fix is appreciated. Thanks

Related

[Q] Kindle fire charge port help

He guys new to the forum, have a question for some help, I'm going to add an external USB port, because that part of my mother board is shot from some previous shotty solder work from someone, anyways, I'm trying to figure out where to solder the 5 wires, the pads from the old port are crap, trying to find somewhere else to solder wires, any help would be appreciated.

Broken antenna connector

Hi i replace the screen of my i747 and when i pull out the antenna from the connector, the whole connector has removed!!! :crying:
theres is any way to fix it? or something???

[Q] [hardware] what kind of connector is the antenna?

Hi can someone identify what kind of connector the antenna uses?
It broke off with the cable need to replace a new one.
If you can give exact model, it would be much appreciated.
attached with picture of board

Little to no signal after changing out fried charger port.

My phone's charger port was recently fried when my phone got stuck in a boot loop over night while charging. I bought a new board and replaced it but now I have no service. I occasionally get full LTE reception but do not have mobile data at all. Is it possible that the blue cable, which I have seen referred to as the WIFI Flex Cable, is causing the problem? The M919 has the one blue cable, but the other variants have two cables that connect to this board. Anyone have any idea about this? Any help would be appreciated.
Where did you get the USB flex cable? It could be the flex cable that is the problem. I have read other posts where people replaced their phone's flex cable which resulted in network signal, charging, data transfer, or wifi problems.
audit13 said:
Where did you get the USB flex cable? It could be the flex cable that is the problem. I have read other posts where people replaced their phone's flex cable which resulted in network signal, charging, data transfer, or wifi problems.
Click to expand...
Click to collapse
I didn't change it out. I used the same one that was connected to the previous board. I just bought one and am going to replace it to see if that fixes it. That's my last hope before I have to buy a new phone so here's hoping.

Problems with USB connection

I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB. OK Fine and dandy if I wouldn't be total idiot and wipe system while trying to install new ROM before transferring ROM image to internal storage.
Now I have FLO paper clip able to go to TWRP but can't install nothing. As far I understand there's no way to enable wifi in TWRP.
Any ideas what would needed to be replaced to make my FLO work again so I can put some ROM on it and make it work again.
I'm not sure if USB daughter board would suffice and solve my problem. Any suggestions?
jxl69 said:
I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB.
Click to expand...
Click to collapse
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
k23m said:
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
Click to expand...
Click to collapse
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
jxl69 said:
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
Click to expand...
Click to collapse
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
dave457 said:
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
Click to expand...
Click to collapse
Even tho charging works? The only problem is data part of USB connection. USB OTG will not work neither will it connect to a PC for file transfer/adb. But if connected to PC or plug device charges. I believe it will not charge past 80 or 90%.
jxl69 said:
Even tho charging works? .
Click to expand...
Click to collapse
Yes

Categories

Resources