I rooted it and flash custom rom "InsertCoin 4.1.1'. Still S-on. Firewater method doesn't work. And Sunshine method also doesn't work because of the custom rom. It requires stock sense,near stock rom.
I want my phone way it was before I root the device. (Stock m8)
My CID SPCS_004
firmware 2.16.654.4
Please help me....
Ruu in Android development will do the trick for you
tjeeeeee said:
Ruu in Android development will do the trick for you
Click to expand...
Click to collapse
Never seen a 2.16.654 ruu there ! Can you point me to it please. As for additional information :
He can't install any other ruu than a 2.16.654 or higher one since he has no S-OFF.
kelum17 said:
I rooted it and flash custom rom "InsertCoin 4.1.1'. Still S-on. Firewater method doesn't work. And Sunshine method also doesn't work because of the custom rom. It requires stock sense,near stock rom.
I want my phone way it was before I root the device. (Stock m8)
My CID SPCS_004
firmware 2.16.654.4
Please help me....
Click to expand...
Click to collapse
Check for maximus or arhd (NOT the lollipop versions but a slight older one) in the dev section or get a new stock backup matching your version number in the general section - collection of firmwares, stock backups and more by @exocetdj
And if that doesn't give you the correct steps and files than try the specific Sprint M8 support subforum
http://forum.xda-developers.com/showthread.php?t=2729173
It's listed under "previous" in the main post
tjeeeeee said:
http://forum.xda-developers.com/showthread.php?t=2729173
It's listed under "previous" in the main post
Click to expand...
Click to collapse
Ah i see in the Sprint section. Maybe it's good to mention that too in the first reply because this is the international section and therefore doesn't hold Sprint ruu files. So that confused me a bit. Thanks for the link
My bad I didn't realize that
Thanks both. Really appreciated your advice. I tried steps in below link
http://forum.xda-developers.com/showthread.php?t=2729173
Flash firmware via HBOOT
Flash Firmware via fastboot
I grabbed the firmware in https://www.androidfilehost.com/?fid=23578570567713359
But both ways failed.
Please let me know how to flash RUU ?
are there any differences between RUU.exe and RUU.zip ?
You flash RUU via computer
tjeeeeee said:
My bad I didn't realize that
Click to expand...
Click to collapse
tjeeeeee said:
You flash RUU via computer
Click to expand...
Click to collapse
Tried both ways below
download 2.16.654.4 RUU.zip
extract it and found 0P6BIMG.zip
move it to sd card and reboot via bootloader
Nothing happends
rename the RUU.zip file as firmware.zip
place it in adb directory
boot the phone into hboot mode and plug into pc and choose fastboot. it turns to fastboot usb
right click on the adb directory with shift and open the command promt
typed Fastboot oem rebootRUU
when see the black screen w/ HTC, typed Fastboot flash zip firmware.zip
it always gives error 99
Please help me to sort out this thing
kelum17 said:
Tried both ways below
download 2.16.654.4 RUU.zip
extract it and found 0P6BIMG.zip
move it to sd card and reboot via bootloader
Nothing happends
rename the RUU.zip file as firmware.zip
place it in adb directory
boot the phone into hboot mode and plug into pc and choose fastboot. it turns to fastboot usb
right click on the adb directory with shift and open the command promt
typed Fastboot oem rebootRUU
when see the black screen w/ HTC, typed Fastboot flash zip firmware.zip
it always gives error 99
Please help me to sort out this thing
Click to expand...
Click to collapse
Run Ruu exe through pc itll reset phone completely stock
You can't apply any of the above methods due to having s-on you have to Ruu using the application via computer to complete stock then you'll be able to update like usual for otas
tjeeeeee said:
Run Ruu exe through pc itll reset phone completely stock
You can't apply any of the above methods due to having s-on you have to Ruu using the application via computer to complete stock then you'll be able to update like usual for otas
Click to expand...
Click to collapse
Do I need run 2.16.654.4 RUU.exe file ?
Yes also don't forget to relock bootloader as well
tjeeeeee said:
Yes also don't forget to relock bootloader as well
Click to expand...
Click to collapse
Before I run the RUU.exe do I neet to unlock the bootloader (using fastboot oem lock command) ?
Or run normally ?
And how to relock the bootloader ?
kelum17 said:
Before I run the RUU.exe do I neet to unlock the bootloader (using fastboot oem lock command) ?
Or run normally ?
And how to relock the bootloader ?
Click to expand...
Click to collapse
Fastboot oem lock
That's the command to relock it.
Mr Hofs said:
Fastboot oem lock
That's the command to relock it.
Click to expand...
Click to collapse
Should I need to unlock the bootloader before run RUU.exe ?
How could I do that ?
Please help
kelum17 said:
Should I need to unlock the bootloader before run RUU.exe ?
How could I do that ?
Please help
Click to expand...
Click to collapse
If you have a s-on device you need to relock the bootloader before running the ruu.exe !
Mr Hofs said:
If you have a s-on device you need to relock the bootloader before running the ruu.exe !
Click to expand...
Click to collapse
Please advice below steps are correct
turn off the phone and press volume down button with power button
when highlighted as HBOOT plug device to the pc
then press volume down button and select fastboot
when it turns to fasboot usb right clock on the adb directory with shift, select command promt
and type 'fastboot oem lock' command
Then how I run the RUU.exe ?
please advice me step by step
kelum17 said:
Please advice below steps are correct
turn off the phone and press volume down button with power button
when highlighted as HBOOT plug device to the pc
then press volume down button and select fastboot
when it turns to fasboot usb right clock on the adb directory with shift, select command promt
and type 'fastboot oem lock' command
Then how I run the RUU.exe ?
please advice me step by step
Click to expand...
Click to collapse
uhm well, you double click the ruu.exe on the pc. That should do the trick
Hi
I relock the bootloader and did the prrevious steps. Now its worked.
Now it shows "RELOCKED" in the bootloader menu.
Is it the normal sign ?
Yes as you are s-on that's normal. Only with s-off you can change those flags to LOCKED
Related
i need this ruu... where is download link?
bernyfur said:
i need this ruu... where is download link?
Click to expand...
Click to collapse
same question ..
http://depositfiles.com/files/ygjw5i97i
i found only this
What ruu, Its not just a ruu, you need your CID and Main version number to get to the right ruu.
Fastboot oem readcid
Fastboot getvar version-main
See what comes out
Mr Hofs said:
What ruu, Its not just a ruu, you need your CID and Main version number to get to the right ruu.
Fastboot oem readcid
Fastboot getvar version-main
See what comes out
Click to expand...
Click to collapse
Cid - TIM_401
Version Main - 3.14.901.24
You won't find a branded JB tmob ruu.....never seen it in the resources
Try this :
Download the 2.17.901 nandroid from here
http://forum.xda-developers.com/showthread.php?t=1975140
Restore it and flash the matching 2.17 stock recovery. Check manually for updates afterwards and update the phone again to the JB software
RUU TIM__401 impossible to found
Hi, I have my HTC One X blocked in boot.
My problem is that I don't have any backup and my smartphone is empty, no date in SD.
I tried a lot of RUU ( I read just ICS) but nothing, I tried to extract boot, recovery and sistem img from RUU to flash via adb but nothing. I tried to write CID, use adb sideload....... I' don't know what I can try......
Please Someone can help me????
Of course I have bootlader unblocked......
zoulu said:
Hi, I have my HTC One X blocked in boot.
My problem is that I don't have any backup and my smartphone is empty, no date in SD.
I tried a lot of RUU ( I read just ICS) but nothing, I tried to extract boot, recovery and sistem img from RUU to flash via adb but nothing. I tried to write CID, use adb sideload....... I' don't know what I can try......
Please Someone can help me????
Of course I have bootlader unblocked......
Click to expand...
Click to collapse
flash Philz 5,15,9 recovery mount sd card then copy your custom rom to sd card install it via recovery and last go in bootloader and flash boot.img from rom archive via fastboot
First, thanks for your help.
I have tried to follow this guide http://forum.xda-developers.com/showthread.php?t=2746940 but it's impossible for me to see my device in adb.
Attached my situation now....
BINGO!!!!!!!!!!!
I'de sloved in this way:
"it's so easy, just turn off your android device, then hold down both "Volume Down" key and "Power" at the same time, wait a few seconds till it start in recovery mode, done.
now type adb devices, and you'll see your device."
http://forum.xda-developers.com/showpost.php?p=46672856&postcount=7
THANKS
hello guys,
i really need help with something:
i got an HTC One X Tegra 3 worldwide one:
CID HTC_044
ICS 4.0.4
*** UNLOCKED ***
S-On
H-Boot 0.94.0000
with clockworkmod 5.8.4.0
without root access.
i want flash a custom ROM, why questions are: (S720e)
1.do i have to unlock the bootloader (it is written ***unlocked*** so i think i don't have to unlock it because it already unlocked am i right?)
2.do i need a root access to flash new ROM?
3. do i have to updrage my H-BOOT to install new custom ROMs ? and how i do it?
4.how i get root access (the one click method didn't work for me..)
5.do i have to flash new recovery? (i dont think i need cause i have one already)
6. if i dont need make root, unlock the bootloader, flash new recovery i just move the zip to the phone and install it from the recovery?
i am noob, please help me,
THANKS FOR EVERY ONE WHO HELP!!
zivonex said:
hello guys,
i really need help with something:
i got an HTC One X Tegra 3 worldwide one:
CID HTC_044
ICS 4.0.4
*** UNLOCKED ***
S-On
H-Boot 0.94.0000
with clockworkmod 5.8.4.0
without root access.
i want flash a custom ROM, why questions are:
1.do i have to unlock the bootloader (it is written ***unlocked*** so i think i don't have to unlock it because it already unlocked am i right?)
2.do i need a root access to flash new ROM?
3. do i have to updrage my H-BOOT to install new custom ROMs ? and how i do it?
3.how i get root access (the one click method didn't work for me..)
5.do i have to flash new recovery? (i dont think i need cause i have one already)
6. if i dont need make root, unlock the bootloader, flash new recovery i just move the zip to the phone and install it from the recovery?
i am noob, please help me,
THANKS FOR EVERY ONE WHO HELP!!
Click to expand...
Click to collapse
You have a very old h-boot so you need to upgrade it first!!
So you need to flash the stock rom for your hboot or the ruu of your hboot and then when the hboot is 1.36 or 1.39 are the two best, you can flash a rom without problems!!
You dont have to unlock bootloader because is unlocked!
Sent from my HTC One X using xda app-developers app
1: no
2: no
3: yes (explain at the end)
4: flash a new custom rom (better then stock)
5: no
6: you install a new rom by
Flashing the boot.img with fastboot commands, make a FULL wipe in recovery and install a new rom.
The easiest way to get you upgraded is to get you to full stock and update via official HTC ota
Can you perform a fastboot command :
Fastboot getvar version-main
Please post the number
Mr Hofs said:
1: no
2: no
3: yes (explain at the end)
4: flash a new custom rom (better then stock)
5: no
6: you install a new rom by
Flashing the boot.img with fastboot commands, make a FULL wipe in recovery and install a new rom.
The easiest way to get you upgraded is to get you to full stock and update via official HTC ota
Can you perform a fastboot command :
Fastboot getvar version-main
Please post the number
Click to expand...
Click to collapse
what that command do? just give the number?
how i use it? how it works?
sorry that im a noob
Download ANDROID SDK BUNDLE (Google) unpack it and navigate to the platform tools. Point in that folder and hold down shift + click the right mouse button and select
Open command window here
Now put the phone in the bootloader and type in the command window on the pc
Fastboot getvar version-main
It will give the number we need for the right ruu !
Mr Hofs said:
1: no
2: no
3: yes (explain at the end)
4: flash a new custom rom (better then stock)
5: no
6: you install a new rom by
Flashing the boot.img with fastboot commands, make a FULL wipe in recovery and install a new rom.
The easiest way to get you upgraded is to get you to full stock and update via official HTC ota
Can you perform a fastboot command :
Fastboot getvar version-main
Please post the number
Click to expand...
Click to collapse
Mr Hofs said:
Download ANDROID SDK BUNDLE (Google) unpack it and navigate to the platform tools. Point in that folder and hold down shift + click the right mouse button and select
Open command window here
Now put the phone in the bootloader and type in the command window on the pc
Fastboot getvar version-main
It will give the number we need for the right ruu !
Click to expand...
Click to collapse
not working
C:\Android\android-sdk\sdk\platform-tools>Fastboot getvar version-main
< waiting for device >
_
its stucks like that....
i also tried with 'fastboot' i mean with low case 'f'
Uninstall HTC sync manager if you have it installed .....but leave the drivers on the pc
Mr Hofs said:
Uninstall HTC sync manager if you have it installed .....but leave the drivers on the pc
Click to expand...
Click to collapse
dont have HTC sync manager.
got the drivers.
Then it should work ! Do you have a MYHTC in the device manager of windows ?
yes i have it
Sent from my HTC One X using xda app-developers app
And you have the phone in the bootloader and you see "fastboot usb" in red text ?
Mr Hofs said:
And you have the phone in the bootloader and you see "fastboot usb" in red text ?
Click to expand...
Click to collapse
yup
Sent from my HTC One X
Hmm strange......sure you opened the command prompt inside the folder where also the fastboot and adb files are ?
Using the original HTC cable, usb 2.0 port on the pc ?
Mr Hofs said:
Hmm strange......sure you opened the command prompt inside the folder where also the fastboot and adb files are ?
Using the original HTC cable, usb 2.0 port on the pc ?
Click to expand...
Click to collapse
yes! i opened the CMD in the platfom-tools folder (the folder you told me with the adb abd fastboot files) i used original HTC cable (the one i got with my phone) and im 100%sure i used good usb port.
you think i need to try the other port?
EDIT:
version-main: 1.28.707.10
finished. total time: 0.007s
Sent from my HTC One X
I don't know what to think
Try a reboot of the pc and the phone ..... It should work. All the things seems to be in order. Maybe you have another pc around to test it on.
The joy of dodgy usb ports. I had this too last night
Htc One X Viper 3.4.2
Mr Hofs said:
I don't know what to think
Try a reboot of the pc and the phone ..... It should work. All the things seems to be in order. Maybe you have another pc around to test it on.
Click to expand...
Click to collapse
here i made:
version-main: 1.28.707.10
finished. total time: 0.007s
Iceax123 said:
The joy of dodgy usb ports. I had this too last night
Htc One X Viper 3.4.2
Click to expand...
Click to collapse
that is s*cks
Sent from my HTC One X
Oke here we go !
Download this file
http://bugsylawson.com/index.php/fi...11-radio-1120410514-release-260743-signedexe/
Backup everything from the phone you need, even a backup of the sdcard ! Because this will wipe all
1: charge the battery if its at low level
2: put the phone in the bootloader and relock the bootloader
Fastboot oem lock
3: keep the phone in the bootloader/fastboot usb mode
4: select the ruu with a right mouse button click and select
"Run as administrator"
5: sit back and follow the installer
This will bring back the phone to full stock, after this you go into the settings menu - about - software updstes.....you update as much as you can until it doesn't detect any updates anymore !!!
Mr Hofs said:
Oke here we go !
Download this file
http://bugsylawson.com/index.php/fi...11-radio-1120410514-release-260743-signedexe/
Backup everything from the phone you need, even a backup of the sdcard ! Because this will wipe all
1: charge the battery if its at low level
2: put the phone in the bootloader and relock the bootloader
Fastboot oem lock
3: keep the phone in the bootloader/fastboot usb mode
4: select the ruu with a right mouse button click and select
"Run as administrator"
5: sit back and follow the installer
This will bring back the phone to full stock, after this you go into the settings menu - about - software updstes.....you update as much as you can until it doesn't detect any updates anymore !!!
Click to expand...
Click to collapse
thanks alot!!
Just 3 more questions:
*how i relock the bootloader?
*is it safe?
*full stock means sense stock? or clean ics?
Sent from my HTC One X
1. fastboot oem lock
2. Yes, totally
3. Sense stock.
Hello,
First of all, it has been a while since i've done tweaking my old one X, but my dad uses the phone now, and he asked me to update it, since the old rom crashed sometimes.
now i found out the was android 4.2 roms available for the one x, and wanted to flash them.
although, i figured out, i needed a higher Hboot, since mine was at 0.95, i needed 1.29+.
tried to figure out how this worked, and i thought i finally knew it, but than the last step wouldn't want to complete, while in RUU, it didn't want to do what it had to do..
so after some hours shouting at my pc and phone, i decided it had enough of it, and would just flash another rom, which didnt need the higher Hboot.
but now comes the crap...
i downloaded one_X_sfied rom, and i though hey its finally working, i saw the bars going green, and all the stuff..
but while rebooting the phone, it wouldnt go past HTC - quietly briliant - logo. so i decided to install it once more via recovery.
again all bars go green.. but this time it wouldnt start the phone either..
so i wanted to go back to recovery, but now it wont load recovery either! when i click on my recovery, it boots the phone again, and keeps rebooting at HTC logo..
i found out i made a mistake, and didnt flash the new kernel for this rom, i was little bit hurried.. so i guess overlooked it... stupid me, i know....
anyway, only thing i can access now is the fastboot and hboot, my bootloader is unlocked, and hboot is 0.95.
my cidnumber is: HTC E___11
there was another number, i thought RUU number, but i don't know the command to get it anymore, don't know if i need it..
anyway, now my question..
how do i ever get this phone working again, if it's even possible...?
any ideas?
thanks alot for reading and applying.
(sorry for grammar mistakes )
- edit -
now it somehow restarted the bootloader, and stops at ''checking sd card update...''
which means. i cant even get into fastboot either.. guess im screwed up now ... ----------lucky me, it shows the fastboot again.. sweat for nothing
what is your version?
what version do you mean?
RUU?
Have you flashed the right RUU for sure ? Try flashing again and remember that you have to relock the bootloader before !
r33fd said:
Have you flashed the right RUU for sure ? Try flashing again and remember that you have to relock the bootloader before !
Click to expand...
Click to collapse
i did not flash any RUU.
i don't know how to get that code, not the E11 thing, but those numbers.
if i am right i have to:
get the original RUU software.
flash this through fastboot using my CMD on PC
relock bootloader first.
but i need the correct RUU file first, and i don't know where to find, because i need that numers, i forgot the command to get it, and cant find it on internet now :\
---
anyway, is this correct? what i say above. -> download correct RUU file -> lock bootloader -> flash via PC -> than something else?
if im correct, i will have a original, non-rooted HOX. correct?
Qgem said:
i did not flash any RUU.
i don't know how to get that code, not the E11 thing, but those numbers.
if i am right i have to:
get the original RUU software.
flash this through fastboot using my CMD on PC
relock bootloader first.
but i need the correct RUU file first, and i don't know where to find, because i need that numers, i forgot the command to get it, and cant find it on internet now :\
---
anyway, is this correct? what i say above. -> download correct RUU file -> lock bootloader -> flash via PC -> than something else?
if im correct, i will have a original, non-rooted HOX. correct?
Click to expand...
Click to collapse
connect phone to pc and boot into fastboot.
open command prompt then enter this command
fastboot getvar version-main
robchongke said:
connect phone to pc and boot into fastboot.
open command prompt then enter this command
fastboot getvar version-main
Click to expand...
Click to collapse
it says:
1.29.401.11 version main
- edit -
downloading orginal RUU now. with version 1.29.401.11
Qgem said:
it says:
1.29.401.11 version main
- edit -
downloading orginal RUU now. with version 1.29.401.11
Click to expand...
Click to collapse
relock bootloader then run RUU. after that you can now update phone to Jellybean, root and flash custom rom.
robchongke said:
relock bootloader then run RUU. after that you can now update phone to Jellybean, root and flash custom rom.
Click to expand...
Click to collapse
just to be sure.
1. connect phone
2. fastbootmode
3. command: fastboot oem lock
4. cammand: to ruu mode? - forgot this one, but i can find if i need it
5. run the downloaded RUU, - i have to run as admin on my PC?
thats it right?
No....
Boot to bootloader and relock it
Fastboot oem lock
Then put the phone in the locked bootloader and run the ruu with administrator rights.
You can use this one
http://bugsylawson.com/files/file/1...12-radio-2120413520-release-274900-signedexe/
Qgem said:
just to be sure.
1. connect phone
2. fastbootmode
3. command: fastboot oem lock
4. cammand: to ruu mode? - forgot this one, but i can find if i need it
5. run the downloaded RUU, - i have to run as admin on my PC?
thats it right?
Click to expand...
Click to collapse
1. Boot your phone to fastboot mode by holding power+vol down button for 10 secs..(if your phone keeps restarting in normal phone mode, go to Setting>Power and untick Fast boot)
2. Plug your phone into your PC and open a Command Prompt.
(windows XP - Click Start > Run > type CMD in box then press OK
(Windows 7 - Click Start > type CMD in search box then press Enter)
3. cd to the location of your fastboot files folder
4. Relock bootloader - type command:
Code:
fastboot oem lock
The phone will then restart into fastboot again showing "RELOCKED"
6. On your pc run the RUU that you downloaded earlier, follow the steps as prompted and patiently wait for it to finish.
REMEMBER your phone should be charged ABOVE 50% AND if the ruu or restore is INTERRUPTED 4 any reason during restore your
phone MAY be PERMANENTLY BRICKED..
Click to expand...
Click to collapse
here's the steps.
robchongke said:
here's the steps.
Click to expand...
Click to collapse
thanks,
how long can it take ?
its already standing like 5min on ''gathering info about the android phone''
is this normal?
Qgem said:
thanks,
how long can it take ?
its already standing like 5min on ''gathering info about the android phone''
is this normal?
Click to expand...
Click to collapse
yep. maybe 5-10 mins.
hi friends
i got htc desire HD a9191 phone but its stuck on htc logo
Ace pvt SHIP S-On RL
Hboot -2.00.0027
MICROP-0438
RAdio -26.14.04.28_M
Emmc-boot
Sep 7 2011 ,19:0:24
Even factory reset and recovery is not working
Factory reset : ON clicking factory phone gets stuck (i.e even menu gets unresponsive)
Recovry : clicking recovey phone vibrates 7 times:crying:
Bootloader
vippz said:
hi friends
i got htc desire HD a9191 phone but its stuck on htc logo
Ace pvt SHIP S-On RL
Hboot -2.00.0027
MICROP-0438
RAdio -26.14.04.28_M
Emmc-boot
Sep 7 2011 ,19:0:24
Even factory reset and recovery is not working
Factory reset : ON clicking factory phone gets stuck (i.e even menu gets unresponsive)
Recovry : clicking recovey phone vibrates 7 times:crying:
Click to expand...
Click to collapse
Things that you forgot to mention is BOOT LOADER,is it locked Or unlocked?
it will written above your phone's Hboot -2.00.0027.
If it's unlocked that try locking it back and then run stock RUU the one you were using it in last working stat.
Thanks.
How would i get to know thats its unlocked
Because its not mentioned any where on screen. what I can tell u i its was working every sim card was working on this phone .
I am new to this please if possible explain me in detail :good:
No Worry Bro!
vippz said:
How would i get to know thats its unlocked
Because its not mentioned any where on screen. what I can tell u i its was working every sim card was working on this phone .
I am new to this please if possible explain me in detail :good:
Click to expand...
Click to collapse
Don't get panic!
It's really easy.....as you may check that i am also new to xda infect i registered on December last month,ever since then i get to know things which i didn't know before so don't worry it will take time but you will know step by step.
As you have mention about S-On and some other detail by pressing volume down and power button.,the same way do it.
first phone should be switched off,and press volume down and power button together,once you see white background with several information regarding your phone's current status.
HBOOT
FASTBOOT
RECOVERY
and some others but in that screen look for top on the list it should written locked or relocked,if not then you have to lock it back in order to run any stock RUU.
as you said that any sim card works which means that your phone is unlocked to network. but for now if there is no other issue in your phone than you have to relock the bootloader in order to run STOCK RUU.
without locked boot loader you won't be able to install RUU.
If it stats ***Locked*** than just flash any RUU by double clicking on it.,if not than just follow this: http://forum.xda-developers.com/showthread.php?t=2133336
But its says nothing locked or unlocked at the top
and how to enable USB Debgging
I tried the link above
and EasyUnlockTool.cmd says the following
***ERROR***ERROR**ERROR
Phone not plugged in
or
Driver not Installed
or
USB debugging not enbaled
***ERROR***ERROR**ERROR
vippz said:
How would i get to know thats its unlocked
Because its not mentioned any where on screen. what I can tell u i its was working every sim card was working on this phone .
I am new to this please if possible explain me in detail :good:
Click to expand...
Click to collapse
unlocked network doesn't mean your bootloader is already unlocked..
@dr.patron99
sorry just wanna correct this...
unlocked network doesn't mean the bootloader is already unlocked..both are is separate different thing...
vippz said:
But its says nothing locked or unlocked at the top
and how to enable USB Debgging
I tried the link above
and EasyUnlockTool.cmd says the following
***ERROR***ERROR**ERROR
Phone not plugged in
or
Driver not Installed
or
USB debugging not enbaled
***ERROR***ERROR**ERROR
Click to expand...
Click to collapse
you can try flashing RUU with the latest or same version as you know that you already using it..but firstly you must find the correct RUU that are suitable with you CIDnum (country ID) of you phone...or else you might using a goldcard method
to check the CIDnum of your phone..your pc must have the latest HTC driver (you can find it here ), and your must already had ADB/ SDK to running android debugging bridge (you can download it minimal ADB from here or download full SDK from here )
after that get your phone to the bootloader n select FASTBOOT then connecting your phone with your pc..then open cmd and change source to your ADB / SDK folder..then typing "fastboot devices" (this is to see connected of your phone to pc)
if success connected..the output will prompt it of your phone serial number..after that you can continue to typing "fastboot getvar all"
then see your CIDnum in the line of output "INFOCID.....XXXX"
hope this help..
JJeamy said:
unlocked network doesn't mean your bootloader is already unlocked..
@dr.patron99
sorry just wanna correct this...
unlocked network doesn't mean the bootloader is already unlocked..both are is separate different thing...
you can try flashing RUU with the latest or same version as you know that you already using it..but firstly you must find the correct RUU that are suitable with you CIDnum (country ID) of you phone...or else you might using a goldcard method
to check the CIDnum of your phone..your pc must have the latest HTC driver (you can find it here ), and your must already had ADB/ SDK to running android debugging bridge (you can download it minimal ADB from here or download full SDK from here )
after that get your phone to the bootloader n select FASTBOOT then connecting your phone with your pc..then open cmd and change source to your ADB / SDK folder..then typing "fastboot devices" (this is to see connected of your phone to pc)
if success connected..the output will prompt it of your phone serial number..after that you can continue to typing "fastboot getvar all"
then see your CIDnum in the line of output "INFOCID.....XXXX"
hope this help..
Click to expand...
Click to collapse
Sir common,i know unlock to network doesn't mean his device unlock to bootloader as well
May be misspelled.:good:
dr.patron99 said:
Sir common,i know unlock to network doesn't mean his device unlock to bootloader as well
May be misspelled.:good:
Click to expand...
Click to collapse
yap..just wanna correct misspelled..
because..you already suggest it to OP to relock his phone bootloader..that's mean you already assume that his bootloader is already unlocked just not show in the top of bootloader..
because of that...i just wanna correct that..because what i know until now is.. actually the bootloader of Ace..by default is indeed nothing showing state locked or unlocked on the top of bootloader.. that's why i suggest him to flashing RUU again..no needed to relock bootloader first..
i just wanna correct miss direction to the OP....nothing else..
anyway..i'm really glad and appreciated to see you wanna trying helping all people in this forum..mate
JJeamy said:
yap..just wanna correct misspelled..
because..you already suggest it to OP to relock his phone bootloader..that's mean you already assume that his bootloader is already unlocked just not show in the top of bootloader..
because of that...i just wanna correct that..because what i know until now is.. actually the bootloader of Ace..by default is indeed nothing showing state locked or unlocked on the top of bootloader.. that's why i suggest him to flashing RUU again..no needed to relock bootloader first..
i just wanna correct miss direction to the OP....nothing else..
anyway..i'm really glad and appreciated to see you wanna trying helping all people in this forum..mate
Click to expand...
Click to collapse
Thanks buddy this is the information i got from cmd see attachment
please help me further on
could u provide me the link to which i should proceed (i.e what steps i should do next)
thanxxx
vippz said:
Thanks buddy this is the information i got from cmd see attachment
please help me further on
could u provide me the link to which i should proceed (i.e what steps i should do next)
thanxxx
Click to expand...
Click to collapse
that's CID num is for RUU HTC India 3.13.720.2 , but i can't find it anywhere ...
so i think you must using goldcard to flashing another RUU with version above 3.13.720.2
here some of other RUU with version above than yours..:
RUU_Ace_Sense30_S_HKCSL_CHT_3.13.832.4_R_Radio_12.65.60.29_26.14.04.28_M_release_234218_signed.exe
or
RUU_Ace_Sense30_S_TWM_TW_3.16.921.2_Radio_12.65.60.29_26.14.04.28_M_release_247385_signed.exe
you can make a goldcard with a tool from here..
hope this help..
JJeamy said:
that's CID num is for RUU HTC India 3.13.720.2 , but i can't find it anywhere ...
so i think you must using goldcard to flashing another RUU with version above 3.13.720.2
here some of other RUU with version above than yours..:
RUU_Ace_Sense30_S_HKCSL_CHT_3.13.832.4_R_Radio_12.65.60.29_26.14.04.28_M_release_234218_signed.exe
or
RUU_Ace_Sense30_S_TWM_TW_3.16.921.2_Radio_12.65.60.29_26.14.04.28_M_release_247385_signed.exe
you can make a goldcard with a tool from here..
hope this help..
Click to expand...
Click to collapse
But trying creating goldCARD Says
error Device not contected
Please Help what should i do
vippz said:
But trying creating goldCARD Says
error Device not contected
Please Help what should i do
Click to expand...
Click to collapse
sorry..forgot..your phone still can't booting normal..
so i suggest you to unlock bootloader via HTCdev unlock first..then installing custom recovery like 4ext or TWRP..then installing custom rom..
after that..if you still wanna back to the stock again...then you can do it with relock bootloader first then continued to process making a gold card..then flashing the RUU that i give it to you above..
just go to https://www.htcdev.com/ ..don't forget to sign up first..then select unlock bootloader..after that..you must download the latest hboot from there..then extracted the rom.zip from exe..copied to your adb/fastboot.exe folder then update your hboot via fastboot.. with command "fastboot oem rebootRUU" then continued "fastboot flash zip rom.zip" wait until finish..if doesn't automatic reboot just type "fastboot reboot bootloader" then cek your hboot that's already change to hboot 2.00.0029..then you can continued to FASTBOOT mode again..then type "fastboot oem get_identifier_token" ..after you get token...then you can continued to process submit token to htcdev unlock for request unlock.bin from htc to unlock your bootloader..
hope this can help..
JJeamy said:
sorry..forgot..your phone still can't booting normal..
so i suggest you to unlock bootloader via HTCdev unlock first..then installing custom recovery like 4ext or TWRP..then installing custom rom..
after that..if you still wanna back to the stock again...then you can do it with relock bootloader first then continued to process making a gold card..then flashing the RUU that i give it to you above..
just go to https://www.htcdev.com/ ..don't forget to sign up first..then select unlock bootloader..after that..you must download the latest hboot from there..then extracted the rom.zip from exe..copied to your adb/fastboot.exe folder then update your hboot via fastboot.. with command "fastboot oem rebootRUU" then continued "fastboot flash zip rom.zip" wait until finish..if doesn't automatic reboot just type "fastboot reboot bootloader" then cek your hboot that's already change to hboot 2.00.0029..then you can continued to FASTBOOT mode again..then type "fastboot oem get_identifier_token" ..after you get token...then you can continued to process submit token to htcdev unlock for request unlock.bin from htc to unlock your bootloader..
hope this can help..
Click to expand...
Click to collapse
but HTC sycn says no Device connected
And i am not getting any HBOOT Files From HTC Website
please provide me the Latest Downloads here or the links and the process to proceed further on :
vippz said:
but HTC sycn says no Device connected
And i am not getting any HBOOT Files From HTC Website
please provide me the Latest Downloads here or the links and the process to proceed further on :
Click to expand...
Click to collapse
you don't need HTC sync to do that...just download SDK from here.. and placed in C:\ drive on your pc.
then you continued to step :
1. download your hboot update from here..
2. after you already download your hboot.. running that exe file until next to second step..now you must hold at this point..don't close this..let open
3. open explorer then search the rom.zip file under C:\Users\"your username"\AppData\Local\Temp\ "you will see a lot of folder like this {5917E83E-C23B-491F-9D62-6AB7E6E87DC6} and you must try looking one by one by open it and see there is a file dotnetinstaller.exe inside that folder and had a folder like before too {5917E83E-C23B-491F-9D62-6AB7E6E87DC6}..then open it again that folder..now you can find the rom.zip file in there"
4. copying that rom.zip file to your SDK under platform-tools folder..and turn on your phone again with pressing and hold volume down+power until get inside bootloader then select FASTBOOT mode
5. open cmd change source to your SDK / platform-tools folder then typing "fastboot devices" enter to checking first that your phone is already connected properly
5. typing "fastboot oem rebootRUU" enter
6. "fastboot flash zip rom.zip" enter and wait until finish..
7. now if succes you can continued to the step unlocking your bootloader just following instruction from www.htcdev.com
8. if already success unlock your bootloader..then you can continued installing custom recovery like 4ext recovery (just try searching it on google how to do that)
9. download custom rom..then installing
10. done..enjoy it
all command without quote
hope this can help..
JJeamy said:
you don't need HTC sync to do that...just download SDK from here.. and placed in C:\ drive on your pc.
then you continued to step :
1. download your hboot update from here..
2. after you already download your hboot.. running that exe file until next to second step..now you must hold at this point..don't close this..let open
3. open explorer then search the rom.zip file under C:\Users\"your username"\AppData\Local\Temp\ "you will see a lot of folder like this {5917E83E-C23B-491F-9D62-6AB7E6E87DC6} and you must try looking one by one by open it and see there is a file dotnetinstaller.exe inside that folder and had a folder like before too {5917E83E-C23B-491F-9D62-6AB7E6E87DC6}..then open it again that folder..now you can find the rom.zip file in there"
4. copying that rom.zip file to your SDK under platform-tools folder..and turn on your phone again with pressing and hold volume down+power until get inside bootloader then select FASTBOOT mode
5. open cmd change source to your SDK / platform-tools folder then typing "fastboot devices" enter to checking first that your phone is already connected properly
5. typing "fastboot oem rebootRUU" enter
6. "fastboot flash zip rom.zip" enter and wait until finish..
7. now if succes you can continued to the step unlocking your bootloader just following instruction from www.htcdev.com
8. if already success unlock your bootloader..then you can continued installing custom recovery like 4ext recovery (just try searching it on google how to do that)
9. download custom rom..then installing
10. done..enjoy it
all command without quote
hope this can help..
Click to expand...
Click to collapse
After doing what step 5 says that is putting in the command fastboot oem rebootRUU i get 3 dots and nothing happens...
I tried rebooting it manually but the hboot was stuck.
vippz said:
After doing what step 5 says that is putting in the command fastboot oem rebootRUU i get 3 dots and nothing happens...
I tried rebooting it manually but the hboot was stuck.
Click to expand...
Click to collapse
what do you mean stuck..?
did you already see the screen white HTC text with black background after execute command "fastboot oem rebootRUU" ?
just try boot to bootloader again...then select FASTBOOT mode..connect it again with your pc..disable it all antivirus..then try running PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe and following the step until finish..
JJeamy said:
what do you mean stuck..?
did you already see the screen white HTC text with black background after execute command "fastboot oem rebootRUU" ?
Click to expand...
Click to collapse
I mean the phone is in fastboot mode and stuck on the screen as shown below... and the command prompt is showing this screen
vippz said:
I mean the phone is in fastboot mode and stuck on the screen as shown below... and the command prompt is showing this screen
Click to expand...
Click to collapse
just try boot to bootloader again...then select FASTBOOT mode again..and connect it again with your pc..disable it all antivirus..then try running PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe and following the step until finish..
IF that's step above does'n success too..then you can try it..
rename it the rom.zip file that you are already tried to flashing it from fastboot command previously (rename it to PD98IMG.zip)..then copied the file to the root of your sd card..this mean copied just inside your sd card not inside any folder..just using card reader to copied that file..then put it in back again in your phone..then boot to bootloader again with pressing volume down+power then wait until bootloader check the zip file then ask you to update it..
then confirm it with volume UP..wait until finish and ask you to reboot the phone with pressing power button..
hope this can help..
JJeamy said:
what do you mean stuck..?
did you already see the screen white HTC text with black background after execute command "fastboot oem rebootRUU" ?
just try boot to bootloader again...then select FASTBOOT mode..connect it again with your pc..disable it all antivirus..then try running PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe and following the step until finish..
Click to expand...
Click to collapse
The PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe Showed me Showed me screen Rebootiing to Bootloader .......................
noting elsee
What Should I Do v??
vippz said:
The PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe Showed me Showed me screen Rebootiing to Bootloader .......................
noting elsee
What Should I Do v??
Click to expand...
Click to collapse
just try what i said above..
IF .exe step does'n success too..then you can try it..
rename it the rom.zip file that you are already tried to flashing it from fastboot command previously (rename it to PD98IMG.zip)..then copied the file to the root of your sd card..this mean copied just inside your sd card not inside any folder..just using card reader to copied that file..then put it in back again your sd card in your phone..then boot to bootloader again with pressing volume down+power then wait until bootloader check the zip file then ask you to update it..
then confirm it with volume UP..wait until finish and ask you to reboot the phone with pressing power button..
I have a HTC desire HD hboot-2.00.0029, radio 26.14.04.28_M .I installed on it RUU_Ace_Sense30_S_Orange_UK_3.13.61.5_Radio_12.65.60.29_26.14.04.28_M_release_235697_signed .I turn it off and leave it off like 3 weeks. After that when i wanted to turn it on , it starts on a white background with HTC letters and then turn off and start again doing the same thing.
Can somebody help me?Thanks
that's mean boot lop..right..
is the phone still can go to the bootloader...?
if yes...you can try go to bootloader and try select factory reset from there..
anyway..what the detail state of your phone bootloader..?, i mean..is it already unlocked..?, s-off?, or what...?
are you sure... that's the RUU you flashed is the correct that are suitable for your phone..?
hope this help..
JJeamy said:
that's mean boot lop..right..
is the phone still can go to the bootloader...?
if yes...you can try go to bootloader and try select factory reset from there..
anyway..what the detail state of your phone bootloader..?, i mean..is it already unlocked..?, s-off?, or what...?
are you sure... that's the RUU you flashed is the correct that are suitable for your phone..?
hope this help..
Click to expand...
Click to collapse
yes, i tried to do a factory reset..nothing..still rebooting..
nope..it's locked on orange..s-on..but the thing is that i operated on it after i installed that ruu.
i dont know what to do ..
plaYer25 said:
yes, i tried to do a factory reset..nothing..still rebooting..
nope..it's locked on orange..s-on..but the thing is that i operated on it after i installed that ruu.
i dont know what to do ..
Click to expand...
Click to collapse
so you mean that your phone still in stock right..?
while you installing that RUU before..is that already finish..?
did you already tried flashing that RUU again...?, maybe you can try it to flashing it that RUU again but now is tried flashing it from your bootloader..
to do that you must go to bootloader and select FASTBOOT..then connecting it your phone to pc until indicator is FASTBOOT-USB..then try open cmd from your adb / sdk folder..then typing "fastboot oem rebootRUU"..then after that..you can try running again RUU.exe from your computer..and wait until finish..then just tell me if that success booting or not..
hope this help..
JJeamy said:
so you mean that your phone still in stock right..?
while you installing that RUU before..is that already finish..?
did you already tried flashing that RUU again...?, maybe you can try it to flashing it that RUU again but now is tried flashing it from your bootloader..
to do that you must go to bootloader and select FASTBOOT..then connecting it your phone to pc until indicator is FASTBOOT-USB..then try open cmd from your adb / sdk folder..then typing "fastboot oem rebootRUU"..then after that..you can try running again RUU.exe from your computer..and wait until finish..then just tell me if that success booting or not..
hope this help..
Click to expand...
Click to collapse
after i did this command : "fastboot oem rebootRUU" it appers like a menu(see the picture) What should i do?run again that RUU?write a command before i run it?cheers
are you sure you do that command while your phone connected to pc and it's in bootloader FASTBOOT-USB mode..?
and you sure htc driver at your pc correctly detected your phone..?
if so..just try another fastboot command "fastboot getvar all" and just show me the output of this command..
JJeamy said:
are you sure you do that command while your phone connected to pc and it's in bootloader FASTBOOT-USB mode..?
and you sure htc driver at your pc correctly detected your phone..?
if so..just try another fastboot command "fastboot getvar all" and just show me the output of this command..
Click to expand...
Click to collapse
What should i do?you have all details about my phone!!thank you for helping me!!
plaYer25 said:
What should i do?you have all details about my phone!!thank you for helping me!!
Click to expand...
Click to collapse
firstly remove your phone serial number and imei from the attachment picture...avoid someone can cloning your phone...
you can try download this RUU from here..
after that without connecting your phone to pc..firstly you must find the rom.zip file from that RUU.exe..to do that..
just running that RUU.exe until two steps next..then hold there..do not continued and do not closed that..just let it open..then open your explorer..
C:\Users\[your user name]\AppData\Local\Temp\[here you will find a lot folder like this "{5CAD3393-EEC0-44CE-9F93-BCAA365B77FB}"] ..search the latest folder by date..and inside that folder you will find subfolder like that again..open it..here you will see the rom.zip file..just copied the rom.zip file to another location...then after that you can cancel and close it RUU.exe
rename it the rom.zip file to "PD98IMG.zip" then copied to the root directory of your sd card (do not place it in any folder)..you can using card reader to copied that file..
after that...just put it in back your sd card to your phone..then boot up your phone to bootloader..then let the bootloader check it the PD98IMG.zip file..and wait until they ask to updating it..just confirm it with volume up..then wait until finish and ask you to confirm reboot with pressing power button..after that if your phone is already success a booting normal again..you must remove it the PD98IMG.zip file from your sd card..
just let me know if this work or not...
hope this help..
2928249 5959
i cant find any flder with that name
JJeamy said:
firstly remove your phone serial number and imei from the attachment picture...avoid someone can cloning your phone...
you can try download this RUU from here..
after that without connecting your phone to pc..firstly you must find the rom.zip file from that RUU.exe..to do that..
just running that RUU.exe until two steps next..then hold there..do not continued and do not closed that..just let it open..then open your explorer..
C:\Users\[your user name]\AppData\Local\Temp\[here you will find a lot folder like this "{5CAD3393-EEC0-44CE-9F93-BCAA365B77FB}"] ..search the latest folder by date..and inside that folder you will find subfolder like that again..open it..here you will see the rom.zip file..just copied the rom.zip file to another location...then after that you can cancel and close it RUU.exe
rename it the rom.zip file to "PD98IMG.zip" then copied to the root directory of your sd card (do not place it in any folder)..you can using card reader to copied that file..
after that...just put it in back your sd card to your phone..then boot up your phone to bootloader..then let the bootloader check it the PD98IMG.zip file..and wait until they ask to updating it..just confirm it with volume up..then wait until finish and ask you to confirm reboot with pressing power button..after that if your phone is already success a booting normal again..you must remove it the PD98IMG.zip file from your sd card..
just let me know if this work or not...
hope this help..
Click to expand...
Click to collapse
I cant find the root directory in my sdcard...neither the PD98 imagine
JJeamy said:
firstly remove your phone serial number and imei from the attachment picture...avoid someone can cloning your phone...
you can try download this RUU from here..
after that without connecting your phone to pc..firstly you must find the rom.zip file from that RUU.exe..to do that..
just running that RUU.exe until two steps next..then hold there..do not continued and do not closed that..just let it open..then open your explorer..
C:\Users\[your user name]\AppData\Local\Temp\[here you will find a lot folder like this "{5CAD3393-EEC0-44CE-9F93-BCAA365B77FB}"] ..search the latest folder by date..and inside that folder you will find subfolder like that again..open it..here you will see the rom.zip file..just copied the rom.zip file to another location...then after that you can cancel and close it RUU.exe
rename it the rom.zip file to "PD98IMG.zip" then copied to the root directory of your sd card (do not place it in any folder)..you can using card reader to copied that file..
after that...just put it in back your sd card to your phone..then boot up your phone to bootloader..then let the bootloader check it the PD98IMG.zip file..and wait until they ask to updating it..just confirm it with volume up..then wait until finish and ask you to confirm reboot with pressing power button..after that if your phone is already success a booting normal again..you must remove it the PD98IMG.zip file from your sd card..
just let me know if this work or not...
hope this help..
Click to expand...
Click to collapse
i did that..same thing..(..just restarting...
plaYer25 said:
i cant find any flder with that name
Click to expand...
Click to collapse
what windows version you are using..?
plaYer25 said:
I cant find the root directory in my sdcard...neither the PD98 imagine
Click to expand...
Click to collapse
the root directory is mean just place it that file inside your sd card..don't place it that file in any folder "sdcard\[here the root directory]"
plaYer25 said:
i did that..same thing..(..just restarting...
Click to expand...
Click to collapse
can you more cleared and detailed what you mean is..?
did you mean you are already to do all the step i say to flashing it the PD98IMG.zip file through bootloader from the RUU.exe the link that i give it to you above...but the result is still boot loping..?
can you show me detailed of your bootloder correctly..i mean example like this..
***UNLOCKED***
ACE PVT SHIP S-ON RL
HBOOT - X.XX.XXXX
blah blah
blah blah..
because you say before in your first post is that you already had hboot 2.00.0029 version.. but in your attachment picture above is your hboot still 2.00.0027..which are exactly your hboot version is...?
did you already tried unlocking your bootloder via htcdev.com..?, and what exactly your reason to installing that RUU in your first post above..?
JJeamy said:
what windows version you are using..?
the root directory is mean just place it that file inside your sd card..don't place it that file in any folder "sdcard\[here the root directory]"
can you more cleared and detailed what you mean is..?
did you mean you are already to do all the step i say to flashing it the PD98IMG.zip file through bootloader from the RUU.exe the link that i give it to you above...but the result is still boot loping..?
can you show me detailed of your bootloder correctly..i mean example like this..
***UNLOCKED***
ACE PVT SHIP S-ON RL
HBOOT - X.XX.XXXX
blah blah
blah blah..
because you say before in your first post is that you already had hboot 2.00.0029 version.. but in your attachment picture above is your hboot still 2.00.0027..which are exactly your hboot version is...?
did you already tried unlocking your bootloder via htcdev.com..?, and what exactly your reason to installing that RUU in your first post above..?
Click to expand...
Click to collapse
i have finnished all the steps you told me..nothing still booting loop..after i installed that version i tried to update to another RUU(exactly the RUU you told me to download).
now i have RUU ARA:
hboot-2.00.0027
radio: 26.14.04.28_M
i am using win7.after i follow all your steps the phone is still in booting loop..
plaYer25 said:
i have finnished all the steps you told me..nothing still booting loop..after i installed that version i tried to update to another RUU(exactly the RUU you told me to download).
now i have RUU ARA:
hboot-2.00.0027
radio: 26.14.04.28_M
i am using win7.after i follow all your steps the phone is still in booting loop..
Click to expand...
Click to collapse
that's so weird things...
what if you try too installing that RUU.exe like normal way...i mean just connecting your phone with pc (select FASTBOOT mode from your bootloder) then running that RUU.exe until finish..
if that still fail too...then another way is you can try it to unlocking your bootloader via htcdev.com first..then after that you can continued installing custom recovery like 4ext, twrp or cwm..and then installing custom rom..
to unlock your bootloader via htcdev.com...firstly you must update your hboot version to 2.00.0029...that hboot update file is already in there site..just follow instruction from site it self..
JJeamy said:
that's so weird things...
what if you try too installing that RUU.exe like normal way...i mean just connecting your phone with pc (select FASTBOOT mode from your bootloder) then running that RUU.exe until finish..
if that still fail too...then another way is you can try it to unlocking your bootloader via htcdev.com first..then after that you can continued installing custom recovery like 4ext, twrp or cwm..and then installing custom rom..
to unlock your bootloader via htcdev.com...firstly you must update your hboot version to 2.00.0029...that hboot update file is already in there site..just follow instruction from site it self..
Click to expand...
Click to collapse
i have already tried that...i tried for 3-4 times..same results :booting loop.
i will tomorrow that thing with htc..after i unlock it how can i install a recovery?what rom do you advice me to install?and how?thank you..
plaYer25 said:
i have already tried that...i tried for 3-4 times..same results :booting loop.
i will tomorrow that thing with htc..after i unlock it how can i install a recovery?what rom do you advice me to install?and how?thank you..
Click to expand...
Click to collapse
This so weird...because that you told me with these both RUU that you had already installed is all process had success completed until finish....but what i know is...that's impossible the phone while still in stock condition can received two different stock RUU with different cid num too...accept if your already had a goldcard and flashing it just through bootloader..
Anyway...just unlocking that bootloader first then after success unlocking...i will continued told you what step by step you must to do next...
Now i'm gone a sleep..
Sent from my HTCSensation using Tapatalk
JJeamy said:
This so weird...because that you told me with these both RUU that you had already installed is all process had success completed until finish....but what i know is...that's impossible the phone while still in stock condition can received two different stock RUU with different cid num too...accept if your already had a goldcard and flashing it just through bootloader..
Anyway...just unlocking that bootloader first then after success unlocking...i will continued told you what step by step you must to do next...
Now i'm gone a sleep..
Sent from my HTCSensation using Tapatalk
Click to expand...
Click to collapse
i receive this error when i try to unlock bootloader
... INFO[ERR] Command error !!!
OKAY [ 0.007s]
finished. total time: 0.007s
What the command you type...?
Sent from my HTCSensation using Tapatalk
JJeamy said:
What the command you type...?
Sent from my HTCSensation using Tapatalk
Click to expand...
Click to collapse
fastboot oem get_identifier_token
plaYer25 said:
fastboot oem get_identifier_token
Click to expand...
Click to collapse
Did you already update your hboot to version 2.00.0029 first before running that command..?
if not yet...just download this hboot from here.. then flashing this via bootloader..
to flashing this hboot through bootloader is just the same way as my guide in my #8 post..
Sent from my HTCSensation using Tapatalk