Develop Bugs

Evo Motorcycle Mount

I finally found a great solution for mounting my Evo on my motorcycle for GPS and musical entertainment!
Got a custom molded cradle that holds my phone with its protective case as well from here:
http://cgi.ebay.com/SlipGrip-RAM-HOL-Holder-Sprint-HTC-EVO-4G-Phone-Case-On-/400195182898
I found several other options, but this one seemed to be the most secure. Also lots of other mounts would have required that I remove my phone from it's case each time I wanted to mount it, a total pain in the rear.
That mates up to this Ram Mount:
http://www.amazon.com/gp/product/B000XDGJQI
I then installed a 12v outlet and ran a headphone extension under my tank and out under my seat. I use this instead of Bluetooth with my Etymotic ER-6i headphones because they also protect my hearing from road noise while on a long ride. One could just as easily use this setup with Bluetooth headphones as well.
http://www.etymotic.com/ephp/er6i.aspx
So now I have this..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Looks good. I've been contemplating something similar but I'm terrified it will slingshot out of the holder on a twisty or something.
For now I think I'm going to go with a jacket pocket that zips and a bluetooth helmet setup.

skylar.sutton said:
Looks good. I've been contemplating something similar but I'm terrified it will slingshot out of the holder on a twisty or something.
For now I think I'm going to go with a jacket pocket that zips and a bluetooth helmet setup.
Click to expand...
Click to collapse
The riding pic there is me on the Dragon with it mounted. It doesn't get more twisty than that!
I did a 430 mile run that included Cherohala Skyway, Tail of the Dragon and then back down 28 though Highlands, NC with no issues at all.
For those interested, this is all from The Tail of the Dragon:
http://www.youtube.com/watch?v=74RQqdUly5U

Thats a great mount. Nice job! I just recently did something similar for my cruiser, except i mounted a spare otterbox belt clip to the mount on my bike that way i can pop the phone into the cradle otterbox defender and all.

looks good!

I made mine with a stiff rubber case, some pieces for a bicycle rack and zip ties. I have been on some gnarly roads and it hasn't even come close to popping out. Though it did screw with my screen protector

Car "Dock" using Velcro Brand Hook and Loop

So, I'm still waiting for the official Samsung dock with the functional 3-pins. Until then, this is my temporary solution...
Velcro Brand Removable Picture Hangers have a unidirectional hook which makes removing the phone really easy as you just slide it upwards.
The product comes with the hook side and the loop side. The loop is supposed to go on your wall (car) and the hook is supposed to go on the object you're hanging (picture frame) or in this case, the phone. If you put the hook on the phone though, it's going to catch on your pocket, your jacket, your sweater, etc., so I reversed it and put the loop in my car and the loop on the phone.
The hook can go anywhere. I just put it over my CD player because I never use it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you're going to put the hook in the car, make sure you reverse the directions so Velcro is now written upside down and the arrows point down also.
Loop patch on the back of the phone.
Hang it.
Voila
To remove, just slide it straight up. Comes right off.
I've actually been using this solution for about 2 years starting with my Droid X (instead of the official car dock) and later Droid Charge. My brother has it in his WRX, my wife has it in her Outback and I've had it in a Tacoma and most currently, a 328xi.

crap...these images are way too big...
Edit: Fixed

Looks good. However with my car there will be no place for it. I'll keep looking for solutions.

Knether said:
Looks good. However with my car there will be no place for it. I'll keep looking for solutions.
Click to expand...
Click to collapse
Thanks. Out of curiosity, what kind of car do you have? All you need is a few inches of flat real estate somewhere on the dash within your arms reach.

So does this leave sticky residue on the back of my phone? So everytime I take my phone off and want to make a call everyone will see a huge sticky pad?

Nope, removable silicone adhesive. Won't damage painted drywall either.

not bad at all... I need to figure out something, I'm really shocked that they were able to build such a beautiful phone but can't release a decent dock for either desk or vehicle that easily allows us to charge our phone and plug in a audio cable... They need to get it together and provide some accessories so i can give them more of my money!

Mountek CD Slot Mount MT5000-C

I posted this over in the Rezound section, but thought others might like it as well.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Amazon Link:http://tinyurl.com/3n8y64p
Ordered this mount for my wife's car, I use a ProClip unit in my car, seems to work pretty well for what it is. Mountek has them available on Amazon every weekday at 07:00 PST, I ordered mine at 08:15 PST and there were only eight left. I paid $23.90 shipped (USPS first class). I am hoping that it will fit my HTC (with extended battery) as well as my wife's OG Droid. I am not too worried about blocking any radio controls while in use because they are all mirrored on the steering wheel. She was pretty adamant about having something that was removable, and I can't stand the windshield mounts that are available.
Anyone else have any experience with these?
(Here is the video from their site)
Here is the box from USPS, shipped received about a week after ordering. Included was the mount, a piece of adhesive foam, and small instruction sheet.
The mount seems to be built fairly well
This tabbed area inserts into the compact disc slot, then the knob is twisted to expand until "firm" The tabs are soft, so no marring the CD slot.
Here is the adhesive pad. The bottom rest is removable to work with a variety of electronics.
Here is my OG Droid mounted, and then the Vigor with the standard battery.
Here is the side profile with the standard battery cover. As a refresher here is the difference between the standard and extended battery covers...
Here is the mount without the bottom plate, holding the Vigor with the extended battery cover.
Here is me shaking it, with the extended battery, no problems with is falling out. Here is a top down view of the foam sides holding the Vigor.
I don't have my wife's car right now, but here is the mount in my Civic (06-11)...
To those unfamiliar, the Civic had a cd slot that is at a angle, here is with the mount installed.
Now with the Vigor installed (with extended battery) portrait and landscape.
Overall I think it is going to work well. I will update this review if I have any issues...

Nexus S dock mod for GNex

I'm a long time lurker on XDA and appreciate all the work the developers have done on all the great ROMs. I recently dropped my SGS II and decided to replace it with a GSM Galaxy Nexus and must say I love it.
My son decided to use the damaged SGS II and no longer needed his Nexus S. I noticed the desktop dock he had looked close to the curvature of the GNex. The micro USB connector was about an 1/8" low and needed to move back about the same. I went to work on dis-assembling the dock to make the modifications. Below I have a few pics but I didn't document the actual mod process, if there are any questions let me know.
The back cover of the dock will pull off with work and there are a few screws holding everything together. Once these are removed the dock will pop apart at the seam on the front of the dock. Modding the micro USB is actually pretty easy. A larger opening will be needed to move the connection towards the back and top of the dock.
The GNex will fit in the dock without any other modifications but there will be a small gap between the dock and the phone on the connector side. I wanted a more factory look and decided to thin the plastic a little so the GNex would fit snuggly next to the dock with no gaps. I did this with a fin grit sand paper and a buffing wheel on a dremel tool.
These docks can be found as cheap as $5.00 on Amazon. I purchased this dock at Best Buy for $20.
Hope these help explain what I did.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Shot of how nicely the GNex fits in the dock.
You can see that the phone is charging in the dock.
Modded the opening for the micro USB connector.
A little more sanding and the dock would look factory.
These were taken with the phone while working on the dock.
The bracket at the top holds the micro USB connector in place. A few mods were needed to make it fit the GNex.

Nice!

i just ordered one of these docks from amazon for 7 bucks used. hopefully i can mod it successfully so i can dock my galaxy nexus like u did. very good job though modding it.
Edit: I screwed up my dock bad so it no longer works lol. Oh well. Now I know why I don't do stuff myself lol. Plus I didn't have the drill thing u had.

My Nexus 5 Car Dock

The parts....
Nexus Wireless Charger
NEW RELEASE] RINGKE SLIM® Google Nexus 5 Case [BETTER GRIP] [SF BLACK] SUPER SLIM + SF COATED + PERFECT FIT Premium Hard Case Cover for Google Nexus 5 [AT&T, Verizon, Sprint, Unlocked, ECO Package
iOttie Easy View Universal Car Mount Holder for iPhone 5/4S and Smartphone - Retail Packaging - Black
The magenets were just not strong enough in my opinion to handle the bumps I would encounter on the road. I drive an older Jeep Wrangler, it has a very "active" ride and the bumps can be a bit interesting.
So I did some cutting to take off the top of the case so that it is only being used as a ledge to support the Nexus while mounted. Combined with the magnets this provides enough "bump resistance" for me.
I took the front plate off the iOttie and trimmed the back plate down to fit the back of the Wireless Charger. I made it kind of stealthy as you really cannot see the back plate as it hidden behind the locking ring.
It is all held together by SuperGlue and happy thoughts.
Now I just need to find a car lighter plug / cord to power the charger and combined with Bluetooh I will never need to mess with cords while in my car again!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Very cool.
Are those screw holes on the bottom of the charging pad assuming you removed the sticky silicon foot? Did you get a chance to peek inside the charging pad?

Thanks. The screws are hidden under the sticky foot indeed. I didn't take it apart. Thought about it, but decided that I would pass. Hasn't anyone done a breakdown of one of them yet?

Looks good.
How hard was it to take the plate off the front?? Are the magnets really not good enough to hold??
Sent from my Nexus 5 using XDA Premium 4 mobile app

It was a struggle to take apart the iOttie. It is a really well put together car mount.
The magnets might be good enough to hold in a regular passenger car, but not my Jeep Wrangler no. The suspension is too rough and some road bumps can be a bit... fun. Like that dime I ran over the other day. I think it was minted in 1956. The ones from that year are brutal. Surprised I did not break something!