The seal is broke. Anyone managed to do this?
andacro said:
The seal is broke. Anyone managed to do this?
Click to expand...
Click to collapse
When you say jack, are you referring to the plastic flap covering the port…?
If yes, then not the audio jack, but I have replaced the USB / Charging jack as it was cracked. Basically I ordered the new flap from this website – www.rounded.com
Then I pulled out the broken one and inserted the new flap – well I tried inserting it myself but didn’t have the right tool. So went to a normal phone repair shop and they inserted the new one for me free of cost in a few seconds. You might need a pointed but maybe blunt object to insert the rubber thingy attached to the flap into the socket.
Hope this helps.
Thank you for helping me! I mean the flap yes. I have tried to pull it out, but should I pull harder? It's kinda stuck, and I was afraid to snap the string. Now I can give my phone a prolonged life.
andacro said:
Thank you for helping me! I mean the flap yes. I have tried to pull it out, but should I pull harder? It's kinda stuck, and I was afraid to snap the string. Now I can give my phone a prolonged life.
Click to expand...
Click to collapse
Yes, it is a bit hard to pull out. But in my case yes - I just pulled harder and the string did snap! It left behind a part of the original rubber string inside the socket I think.
However the replacement flap that I ordered had a much smaller string, so it was easy to insert it back into the same socket, where a part of the old string was left behind.
Good luck.
Thank you. Thinking of using pliers at the bottom of the string. Maybe it wont snap then.
andacro said:
Thank you. Thinking of using pliers at the bottom of the string. Maybe it wont snap then.
Click to expand...
Click to collapse
Pictures. Or, it didn't happen...
Received the parts today. Changed the USB and audio cover. Used angeled tweezers, and managed to get out all of them by pulling and moving the tweezers downwards when the string stretched. Used the tweezers to insert them too.
Now I got two more years of use.
andacro said:
Received the parts today. Changed the USB and audio cover. Used angeled tweezers, and managed to get out all of them by pulling and moving the tweezers downwards when the string stretched. Used the tweezers to insert them too.
Now I got two more years of use.
Click to expand...
Click to collapse
Do you have the charging dock and a bluetooth headset?
That removes the need to [almost] ever open the flaps right?
Charging dock, but not a bluetooth headset. Don't know why the gasket on the audio jack cover fell off since I seldom use a headset. The USB cover gasket was worn because of all that use of Flashtool.
Related
I recently dismantled my BA to work on the LCD. I originally thought it would be necessary to disconnect the keyboard ribbon from the main board, so I removed the tape and black clip from the surface mount connector. However, it turned out I could leave the ribbon in place, so I didn't remove it.
After reassembly, only a few of the keyboard keys now work, and the blue LEDs no longer work at all.
I was careful not to force or twist the ribbon at all as I worked, so I don't think it's damaged, but I haven't been able to make the black clip go back on properly. I suspect this is the problem. I have tried to reseat the clip but without success and the keyboard is still the same.
Can someone please explain the role of this black clip and tape, and their relevance to the electrical connection. And can anyone direct me to a 1000x magnified picture of how the clip is supposed to fit!
Thanks in advance...
Hi there,
I had a similar problem when dissasembling one of my PPC6600 phones. The ribbon is quite dellicate, and I wound up ripping the outer conductor (it is the thicker one, and it happens to power the backlight LED's). Needless to say, I had to use a very fine tip soldering iron and some hair-fine wire to fix the mess. When I got my hands on a scrap one from EBAY (for like, 75 bucks because the ESN was locked out), I pulled the keyboard from it and replaced my hack.
Also, I have added to the WIKI a procedure to take apart the BA. I think you can find that HERE -> http://wiki.xda-developers.com/index.php?pagename=DIS_BA_PICS
Check out the one pic that is big that shows you how to flip up the clip.
The connector you are talking about has a little black (brown?) clip that flips up 90 degrees to allow the ribbon to come out. If you didn't flip it up, you might have been able to remove the ribbon, but tough luck getting it back in. You can stick your fingernail in there where the ribbon goes, and lift up on the clip. It should pop up ad remain connected quite easily. Also, when you re-insert the ribbon, you want to make sure that the two protruding tabs on the ribbon 'seat' fully against the connector before you push the clip back down onto the ribbon.
Have fun!
When I did the work I had already seen your exellent pics (thanks ) and my black clip came right off when I lifted it. So my problem is getting the black clip back on, so that it can be flipped up and down normally again. At no time did I try to remove the ribbon so I don't think it's damaged - but I'm wondering if the black clip needs to go back properly before the electrical connection is good again.
PS to anyone dismantling BA - remember to remove both the SIM and the SD card/blank, as these both jam the cover and prevent removal - shame if someone missed this and snapped something . (I tried to add this info to the page with pics but the Edit button wouldn't let me do it - gives a "page not found" error.)
Hi again,
My phone doesn't have a SIM card (is this a European thing or are there some carriers in USA that use SIM cards?)
Anyhow, I think I remember dealing with connectors like these before and having that clip pop off. There are two little tabs on the clip that have little round buttons on each side of the clip tabs, and these buttons prodtrude off the sides of the clip. They match a slot on the connector part that is surface mounted to your mainboard. So, you have to align the clip properly so that these protruding bumps 'pop' back into the white housing on both sides. Now, if these tabs broke off.... then I guess you're outa luck, unless I guess you find some very thin plastic that you can shove in on-top of the ribbon (underneath the part of the housing where the clip SHOULD have gone), so that it pushes the exposed conductors of the ribbon down onto the connector.
Hope this helps!
Many thanks, this helps a lot by confirming (a) how the clip fits and (b) its role in the electrical connection. This information is much appreciated as it gives me a fighting chance when I next have a go at fixing the thing!
How do you get by without SIMs? Does that mean a phone is forever tied to the one provider and phone number?
yodafreak said:
My phone doesn't have a SIM card (is this a European thing or are there some carriers in USA that use SIM cards?)
Click to expand...
Click to collapse
It's a GSM thing. GSM phones (like the PDA2K or SX66) use SIM cards, CDMA phones (like the PPC6600) don't.
http://www.youtube.com/watch?v=vsj3IkyAqEU&feature=related
Give to me.
build your own for around 10-15$
http://forum.xda-developers.com/showthread.php?p=28322781#post28322781
I think I like my touchstone better.
Is there any more information for this? costs? rate of charge vs charge over usb/over wall? The video seemed much more of an early preview then anything specific.
punzada said:
Is there any more information for this? costs? rate of charge vs charge over usb/over wall? The video seemed much more of an early preview then anything specific.
Click to expand...
Click to collapse
It is just that.
i read september will bring more info.
I want one so bad, I was really disappointed when I heard it was going to be delayed for who knows when
Sent from my SPH-L710 using Tapatalk 2
Make your own
Buy a TouchStone base and back cover, $12.28 dollars on amazon
http://www.amazon.com/Palm-Pre-Touc...TF8&qid=1341950625&sr=8-4&keywords=touchstone
Take Palm Pre Case apart
Align the four metal circles on the back using the base as a guide
Place pickup coil in the center with the circuit board above it
Place metal foil over the coil as it was before(assuming it came apart in the process)
Tape down using three pieces of scotch tape or one piece of packing tape leaving metal contacts exposed.
Solder wire to the contacts
Add a blob of wire to the other side of the wire and connect to phone (top to top, bottom to bottom assuming the board is above the coil)
Put case together
Done
This works well and by removing all unnecessary plastic, you will get a smaller bump than others get.
ericlmccormick said:
Buy a TouchStone base and back cover, $12.28 dollars on amazon
http://www.amazon.com/Palm-Pre-Touc...TF8&qid=1341950625&sr=8-4&keywords=touchstone
Take Palm Pre Case apart
Align the four metal circles on the back using the base as a guide
Place pickup coil in the center with the circuit board above it
Place metal foil over the coil as it was before(assuming it came apart in the process)
Tape down using three pieces of scotch tape or one piece of packing tape leaving metal contacts exposed.
Solder wire to the contacts
Add a blob of wire to the other side of the wire and connect to phone (top to top, bottom to bottom assuming the board is above the coil)
Put case together
Done
This works well and by removing all unnecessary plastic, you will get a smaller bump than others get.
Click to expand...
Click to collapse
Is there a build video guide on this?
Randomacts said:
Is there a build video guide on this?
Click to expand...
Click to collapse
I'm pretty sure I've seen picture how to's around here and should be on Youtube. I'm blocked at work, so I can't find it at this time.
I was uncomfortable on how close the usb connector sat with the S3 installed in the Infuse car dock. You could actually scratch the S3 bezel if you weren't careful inserting the phone into the dock. This is because the bottom of the Infuse is flat and the S3 is rounded, it makes the S3 sit ever so slightly closer to the usb connector. I took apart the dock and lengthen the "channel", trimmed the retention plate, and removed the middle retention clip that holds the rear cover on. End result is it opens up about 1.0-1.5mm more then normal making ample clearance for the S3
Attached are pictures of the modified dock..
How hard was it to remove the sliding part from the rest of the dock? I am planning to take it apart soon (after my microUSB extension cable comes in) but didnt want to try it until I knew the cable worked. It seems like it would just pop off, but I didnt want to apply too much force yet.
I just need the bottom part to maintain charging and audio out. I plan on hiding it under the dash and just using the extension cable.
Appreciate the info.
the_buzz_man
the_buzz_man said:
How hard was it to remove the sliding part from the rest of the dock? I am planning to take it apart soon (after my microUSB extension cable comes in) but didnt want to try it until I knew the cable worked. It seems like it would just pop off, but I didnt want to apply too much force yet.
I just need the bottom part to maintain charging and audio out. I plan on hiding it under the dash and just using the extension cable.
Appreciate the info.
the_buzz_man
Click to expand...
Click to collapse
Getting the back cover off without breaking it is a bit tricky. There aren't any screws at all and is held in by only clips. I used two really small flay head screwdrivers and popped it up using the location of the Infuse speaker hole. I then wedged in a hobby knife it and used it to pry up all the edges until the rear popped off. Once off you'll need a #00 Philips screwdriver to remove the screws holding the retention plate on.
Here are some more pics of the modifications.
First pic: Lengthen channel and trimmed retention plate
Second pic: This is how much it opened with out any mods.
Third pic: This is how much it opens after the mods.
Good work, I've taken this apart before on the D710 mount I used previously for my Skyrocket and before I got an Infuse mount for the SIII since everyone was raving about them, but I also noticed that it was a little too close for comfort.... I've just been very careful putting it in, but as much as I drive, it's not something I'll be able to protect every time, so I know what my quick little Sunday project will be today!
I also flipped the Samsung logo around
Feel free to use any of these steps I made for the D710 dock modifications I did in order to get a Skyrocket to fit, it may help others with the disassembly of the back portion in order to get to the screws and the sliders:
http://forum.xda-developers.com/showpost.php?p=24453360&postcount=52
Thanks for the tip! I couldn't get the screws loose, so I carefully dremeled the retention bracket in place. Works like a charm!
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
First off, THANKS to vw671!! Soon as I get my dock, I will do this to spare my S3!
KryptosXLayer2 said:
Feel free to use any of these steps I made for the D710 dock modifications I did in order to get a Skyrocket to fit, it may help others with the disassembly of the back portion in order to get to the screws and the sliders
Click to expand...
Click to collapse
Any link by chance? Searched your created threads and couldn't find it... and too lazy to search more
flawedlegacy said:
Any link by chance? Searched your created threads and couldn't find it... and too lazy to search more
Click to expand...
Click to collapse
That's what I get for trying to post the link in the text on my phone! Sorry for being stupid..... Haha, here it is:
http://forum.xda-developers.com/showpost.php?p=24453360&postcount=52
lol, thanks!
sblees said:
Thanks for the tip! I couldn't get the screws loose, so I carefully dremeled the retention bracket in place. Works like a charm!
Click to expand...
Click to collapse
I know what you mean...I had to go to the hardware store to buy a #00 screwdriver to get off the screws! I thought about doing exactly what you did, both will work.
happened to get mine moments ago.... anyone care to explain how to get the back part off exactly? I know you said two clips but where do I pry?
-also, how was the Samsung plate turned around? Already modding it, might as well do that!
EDIT: I GOT IT! -and will try to make a video!
Still interested in the Samsung plate though. tried same method with that and couldn't get it
flawedlegacy said:
happened to get mine moments ago.... anyone care to explain how to get the back part off exactly? I know you said two clips but where do I pry?
-also, how was the Samsung plate turned around? Already modding it, might as well do that!
Click to expand...
Click to collapse
Clip locations in attached pic.
To flip the Samsung logo around you have to get it off obviously. I used a single sided razor blade to pry it up. Then you have to trim two tabs off the back, you'll know which two when you try to put it back on.
flawedlegacy said:
happened to get mine moments ago.... anyone care to explain how to get the back part off exactly? I know you said two clips but where do I pry?
-also, how was the Samsung plate turned around? Already modding it, might as well do that!
EDIT: I GOT IT! -and will try to make a video!
Still interested in the Samsung plate though. tried same method with that and couldn't get it
Click to expand...
Click to collapse
The op mentioned to pry at the headphone jack but I pried it at the rectangle hole (not the usb hole).
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
sblees said:
The op mentioned to pry at the headphone jack but I pried it at the rectangle hole (not the usb hole).
Click to expand...
Click to collapse
I did NOT say pry it from the headphone jack.
I said:
"I used two really small flay head screwdrivers and popped it up using the location of the Infuse speaker hole."
Which is the rectangular hole.
yeah, i got that after pulling my head from my @&# and actually trying. Started from the sides and worked around. Not too bad. All I used was razor and screwdriver. Tried the Samsung plate and snapped the razor, lol.
So I just noticed your "dock" part doesn't have any writing on it. Mine says "LOCK" with a triangle showing to slide it up. odd...
vw671 said:
I did NOT say pry it from the headphone jack.
I said:
"I used two really small flay head screwdrivers and popped it up using the location of the Infuse speaker hole."
Which is the rectangular hole.
Click to expand...
Click to collapse
Oh, I must have misunderstood. When you said speaker hole, my first thought was the 3.5mm hole.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
flawedlegacy said:
So I just noticed your "dock" part doesn't have any writing on it. Mine says "LOCK" with a triangle showing to slide it up. odd...
Click to expand...
Click to collapse
haha...waiting for someone to notice that I scratched the front surface trying to pry open the back so I sanded down the front with 2,000 grit sandpaper. I was going to buffing it back to be polished but ended up liking the matte finish. The finish looks better in person than in the pic because a flash was used...the finish sort of matches the Pebble Blue's texture.
any chance of modding it to fit it with a slim case? someone mentioned heat gun in another thread to expand it a little. thoughts?
socalwrx said:
any chance of modding it to fit it with a slim case? someone mentioned heat gun in another thread to expand it a little. thoughts?
Click to expand...
Click to collapse
It would have to be an ultra thin case. I'm going to try this out.
http://www.bodyguardz.com/armor-car...-iii-verizon.html?dir=asc&order=sort_priority
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
My apple earphone plug broke clean and now is lodged deep inside the phone's jack. I've tried superglue with the ballpoint pen method, didn't work. I was wondering if i was to take the phone apart would i be able to push it out from the other side?
Never use apple products with Samsung!
officekeyboard said:
My apple earphone plug broke clean and now is lodged deep inside the phone's jack. I've tried superglue with the ballpoint pen method, didn't work. I was wondering if i was to take the phone apart would i be able to push it out from the other side?
Never use apple products with Samsung!
Click to expand...
Click to collapse
I would not advise trying to get it apart.You'll wind up destroying the phone. You're on the right track with the superglue but you have to be very careful or good bye ear piece. I've had this happen on my old Lumia phone. I used the same method but instead of using a ballpoint pen I used a bolt the fit inside the headphone slot. Super glue melts plastic so you cant get the proper grab with a ballpoint pen. Try it again that way with a bolt and leave it applied for over an hour to really set in. Then just pull up.
Best of luck to you.
I was trying to fix one problem and ended up making another.. Anyone know if the plastic piece that has the latch on the mother board (zif connector maybe?) that holds the ribbon for the charger can be replaced? The tablet still works but I can now no longer charge it or plug it into the computer. If its not possible to fix that then is wireless charging possible? I know I still wouldn't be able to sync with the computer but I would be good with that as long as I can charge it.
Below is a pic of what im talking about
Erm ouch, im no electrician but i think you may have ****ed it...
Right well best thing i can suggest is that a Samsung repair agent might have to look at it.
(Or you could find the pieces on the Interwebs for it)
I've done this a few times to laptop motherboards years ago. Just use some high quality tape to make sure the connection is complete. If it comes undone you'll just have to redo it, but if you use good tape you shouldn't have to. Definitely not the end of the world, they're just cheap plastic clips.
wbaner said:
I was trying to fix one problem and ended up making another.. Anyone know if the plastic piece that has the latch on the mother board (zif connector maybe?) that holds the ribbon for the charger can be replaced? The tablet still works but I can now no longer charge it or plug it into the computer. If its not possible to fix that then is wireless charging possible? I know I still wouldn't be able to sync with the computer but I would be good with that as long as I can charge it.
Below is a pic of what im talking about
Click to expand...
Click to collapse
Even u manage to wireless charge it and how is tablet suppose to get power from the battery?
The zif connector is cheap, but alot hasssle to remove the board and dont know if the EMI shield is soldered into the board or with screw like Note 10.1 had.
Hard to see from this disassemble video. (scroll to end)
If u got good soldering skills and can find the zif connector part. Then its worth a try.
https://www.youtube.com/watch?v=zOzrRu8PB2Y&list=WL&index=3
Backyard repairs
All you need to do is achieve 2 things.
1. Locate it so that the cable contacts line up with the pins in the connector.
2. Apply pressure on the cable so it has good contact.
Using your fingers put pressur on it and check that its charging when plugged into the usb.
Then tape it in position.
To get the pressure on it, cut a piece of plastic and tape it on the area where it contacts the pins.
Then cut some rubber so that its thick enough such that it puts pressure on that plastic bit when its put back together.
Tape that rubber in position and put cover back on.
Should last, but if not just redo it again and get the rubber thickness right.
warboat said:
All you need to do is achieve 2 things.
1. Locate it so that the cable contacts line up with the pins in the connector.
2. Apply pressure on the cable so it has good contact.
Using your fingers put pressur on it and check that its charging when plugged into the usb.
Then tape it in position.
To get the pressure on it, cut a piece of plastic and tape it on the area where it contacts the pins.
Then cut some rubber so that its thick enough such that it puts pressure on that plastic bit when its put back together.
Tape that rubber in position and put cover back on.
Should last, but if not just redo it again and get the rubber thickness right.
Click to expand...
Click to collapse
haha.. I was messing around and figured this out.. only I put a piece of cardboard box on it and taped it.. put the cover back on it and its charging again.
wbaner said:
haha.. I was messing around and figured this out.. only I put a piece of cardboard box on it and taped it.. put the cover back on it and its charging again.
Click to expand...
Click to collapse
Well it says charging but the percent is still going down?
Going to power off the tablet and see what happens.. ugh
Also watched the video that was posted and I cant really tell much from the video.. if you can just buy one of those sockets and have it put on the motherboard then I will go that route.