I think im soft bricked and ******up pit. I can only flash recovery and it succes only randomly... Battery isnt loading and screen flashes like its going on/off really fast.
When im trying to flash stock rom from sammobile.com it fails with error:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N5100XXDNG2_N5100OXEDNG1_N5100XXDNE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Wow im so blind
Accidentally downloaded n5100 when i have n5110... but it wont even then work. atm trying to install cm trough recovery but it stucks at installing update and suddenly boots to note 8 logo and sits there :crying: wiping data says error "Error mounting /data!" is that problem? Ofcourse its error so its problem but how huge problem is that?
Related
I tried searching but can't seem to find anything that solves this issue.
I had the device about 2 hrs before jumping into rooting. I think I went a little overboard. I tried flashing the CF Autoroot via ODIN. Afterwards, I used CASUAL. That was successful. However, when I attempted to flash the unsecured boot image it failed. Now I can't do anything but get into DL mode.
I've familiar with ODIN since I had a Charge. But I may have jumped in too early too root this phone. Coming from a Galaxy Nexus it's just not as simple - HA!
Anyways, I would be much appreciated if anyone can assist. I believe I need to flash a secured boot image. I don't think the phone was ever unlocked but I have no way of knowing for sure. It will not boot. It gives me the "firmware upgrade was unsuccessful" page. I get the same if I try to charge when the phone is off.
Help please! TIA.
EDIT: This is what I get when I try to flash the CF auto in ODIN.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-t0lte-t0ltexx-gtn7105.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
OH I think I fixed it.
This is pW!
Hi,
a friend of mine got is Galaxy note 2 stuck on a bootloop and we doesn't know what happened. The phone doesn't boot to recovery, only to download mode.
I'm trying to solve his problem but i'me having a lot of difficulties.
I installed all the things needed to do a factory reset:
Install drivers;
Intall ADB & Fastboot
download firmwere from samsung
download MJ5 bootloader
pit file to repartition
downloaded odin 3.07;3.09;3.10
but every time i use any of the odin versions to change the bootloader ou flah the PDA i get the same error:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N7100XXUEMJ5_1903221_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> param.bin
<ID:0/004> tz.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Can any one tell me what could my problem be?
Hi
I got a big problem, my tablet Samsung galaxy Tab 3 sm-110
Well the problem its this :
-Reboot Loop
-Can't see the folder in my pc, because the MTP DEVICE USB cant install, And install Kies, but this dont work to me
I try the hard reset on him and appear the message "No Command"
Try Root the system with Odin v3.09 using CWR (T110.CWM.v6.0.4.8) & TWRP (T110.TWRP.2.7.0.1.tar), but dont work (FAIL)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T110.TWRP.2.7.0.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Pls Somebody can help to solve this, I dont care if I lose the information
To be clear, when you try to do a normal start, you have a bootloop? And you can enter recovery?
My recommendation, at this point (with no further information), is to attempt to use the Kies emergency firmware installation method, or to obtain the full firmware package and flash it via ODIN/Heimdall.
<ID:0/004> NAND Write Start!! <ID:0/004> FAIL! <OSM> All threads completed. Note 2
Hello
i have a problem rooting my mobile samsung galaxy note 2 and now it is stuck in downloading mode .... before that it had a failure logging on always stuck on boot screen
i have installed
samsung drivers
odin 3
kies - had it closed always during the processes of odin
tried to restart / change usb cable and port
nothing seem to work now
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Please help .
thanks in advance
I recommend flashing back to a stock rom from sammobile.com to get a fresh start.
As the title says I can't flash the stock ROM back onto my phone. I stupidly formatted my phone through TWRP last week but I finally managed to get it repartitioned. I've tried everything on Odin I could think of. Here's what the log says:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed
Try installing the same or newer build of the firmware.
Where do I find that?
Sammobile.com
please help! cant flash stock rom back onto phone either
my issue is the exact same issue as him except i am using odin 3.1210, i have downloaded the latest firmware update and i get the same thing he did
an0ym0us said:
As the title says I can't flash the stock ROM back onto my phone. I stupidly formatted my phone through TWRP last week but I finally managed to get it repartitioned. I've tried everything on Odin I could think of. Here's what the log says:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed
Click to expand...
Click to collapse
My error exactly, I've been trying many different things for the past 5 hours still no luck
is this solved?