Ive managed to brick my note2 n7100 softly, i can get it into 0din mode and i can manage to get the phone to my boot screen, how ever i cannot enter recovery mode
Ive flashed with stock roms from sammobiles, after this i can still get to 0din mode and it still boots to the logo then hangs up and just pauses there.
N7100XXUEML2_N7100H3GEML1_H3G Is the what ive used to flash with i also used a PIT file along with it.
I was originally trying to install philz recovery so i could install older firmwares to network unlock my phone, and now my baby wont turn on.
Im not very tech savy..
I would love some advice on how i can rescue my phone.:good:
::
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUEML2_N7100H3GEML1_N7100NEUEML1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> recovery.img
<ID:0/003> system.img
0din gets to the remove and reset stage , then proceeds to my 3 logo boot screen then freezes still.
I can flash N7100XXUEML2_N7100H3GEML1_H3G untill my hearts content, but it still does not give me a recovery mode [vol up+home+power] but i can still access 0din download mode, and the phone still hangs on boot at the 3 logo
Not a clue how ive managed it, but ive got my phone back booted up now.. Now time to figure how to network unlock it!
Related
Im trying to set my phone back to stock after numerous bootloops and nothing works.
Steps ive done:
Ive tried going into recovery and doing a normal new rom install after downloading a new one, been on JBsourcery and its started bootlooping literally for 24 hours or until the battery died.
It kept saying failed after it started to install the the ROM. I even tried reflashing a back up and it also failed.
I downloaded stock rom to flash to odin. It shows connected and runs like normal once i hit start and then it fails. this is the log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> odin.takju.4.3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> bootloader.img
<ID:0/003> radio.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If I try to turn on the device it will show the google logo, blink, google logo again and then takes me to recovery. If anyone can help or point me in right direction to fix, it would be appreciated thanks.
Today just suddenly my note 2 rebooted wasn't watching it and stayed on the Samsung Galaxy note II boot logo.
Can't get in recovery mode tried it for like 40 times now, I can get in download mode hooked it up to odin flashed it odin says no problem or error (see log below)
It's just a stock rom like the one before and rooted, installed nothing weird of experimental, always updated with mobile odin.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXALIJ_N7100TNLALJ2_N7100XXALIH_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
flash stock recovery through Odin, use xda search bar for it.
nitol said:
flash stock recovery through Odin, use xda search bar for it.
Click to expand...
Click to collapse
I tried to install a recovery stock and custom nothing still the samsung Galaxy logo.
Or I'm doing something wrong, just loaded the recovery in odin AP/PDA and left the rest untouched hit start Odin does his thing no error .
Hey,
I have some old samsung ace 2 that I was experimenting around with, wanted to try and get some 5.1.1 ROM on it. But first I figured I needed to get some kernel on it, though I did something which now means that during bootup it is stuck on the samsung galaxy ace 2 logo. I can access ODIN mode, though cant access recovery mode. The battery mode also seems to be broke too as it just displays a loading symbol. So far I have flashed the EK kernel on it with what seems to be a success according to ODIN mode. Also note that Samsung KIES tries to connect to my device in ODIN mode but it never connects and troubleshooting doesnt do anything.
I tried to flash stock firmware to it through the odin software whilst my phone was in odin mode, though it displays a bunch of stuff in the odin pc software then attempts to reboot my phone though it just gets stuck on the boot logo again without odin really doing much here are the logs:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8160XXLD8_ready_to_root_ANT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> kernel.bin.md5
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Reckon my device is still salvagable from this hole I have dug myself in?
i am also having the same problem. tried to flash stock firmware with and without pit, still can't work :crying:
and i don't have jtag and don't know how to use it even if i have jtag :crying:
Need help recovering SM-T310 8", stuck at boot screen, Odin won't load TWRP onto it
I've been trying to get this tab back in working order for several hours now - When I first started working on it, all it showed was the "Samsung Galaxy Tab 3" screen, going right back to that when I turn it off (not even staying off.) I tried putting it in download mode (Power+Down+Home, it does work) and loading TWRP 3.1.1 with Odin (tried both 3.07 and 3.12.3) and it fails almost immediately after hitting Start, Kies won't recognize it over USB, and when I put in the model and S/N it says it's "not eligible".
Also, I've tried using the stock recovery mode, but the factory reset doesn't help, and it doesn't recognize the format of the only rom I could find for it (that doesn't require a premium membership.) It's a .tar.md5, TWRP is supposed to be able to handle it, but the system recovery doesn't see it at all.
(click for big)
Here's the Odin log:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T310.TWRP.3.1.1-0.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Help, please? I've gone through multiple past threads here and on other sites I found on Google to get this far, but I've been unable to make any appreciable progress.
Hello dear friends
I tried to install TWRP Recovery on my Samsung Galaxy A50 A505fn - https://forum.xda-developers.com/galaxy-a50/development/recovery-twrp-galaxy-a50-t3916199 following the exact instructions given in the guide above. After I factory reset the phone and enabled the USB Debugging and OEM Unlock options in the Developer Options menu, I used Odin 3.13.3 and loaded the Magisk Patch file onto the AP Field(while in download mode). After restarting the phone it stuck in a bootloop reaching the samsung logo and resetting again saying that the phone is not running samsung software.
After an unsuccessful try to flash the stock firmware(downloaded the right firmware online - Germany) I went back to download mode and selected the option Lock Bootloader and Factory Reset as a last resort.
Odin Log:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1303)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 68 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> vbmeta.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1303)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> param.bin
<ID:0/003> userdata.img
<ID:0/003> Home Binary Download
<ID:0/003> Total Binary size: 5511 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> up_param.bin
<ID:0/003> cm.bin
<ID:0/003> keystorage.bin
<ID:0/003> uh.bin
<ID:0/003> vbmeta.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Now the phone launches into download mode after a short show-up of the text screen with the "not running official Samsung software" .
Download mode says " Error verifying vbme....: OK_NOT_SIGNED (3)
CUSTOM VBMETA
VBMETA : No sign info
VBMETA ,
I cannot get any further than this, so I would be thankful for any help :highfive:
If any other info is required I'm here to answer.
Kind regards
OblakKoz said:
Hello dear friends
I tried to install TWRP Recovery on my Samsung Galaxy A50 A505fn - https://forum.xda-developers.com/galaxy-a50/development/recovery-twrp-galaxy-a50-t3916199 following the exact instructions given in the guide above. After I factory reset the phone and enabled the USB Debugging and OEM Unlock options in the Developer Options menu, I used Odin 3.13.3 and loaded the Magisk Patch file onto the AP Field(while in download mode). After restarting the phone it stuck in a bootloop reaching the samsung logo and resetting again saying that the phone is not running samsung software.
After an unsuccessful try to flash the stock firmware(downloaded the right firmware online - Germany) I went back to download mode and selected the option Lock Bootloader and Factory Reset as a last resort.
Odin Log:
Now the phone launches into download mode after a short show-up of the text screen with the "not running official Samsung software" .
Download mode says " Error verifying vbme....: OK_NOT_SIGNED (3)
CUSTOM VBMETA
VBMETA : No sign info
VBMETA ,
I cannot get any further than this, so I would be thankful for any help :highfive:
If any other info is required I'm here to answer.
Kind regards
Click to expand...
Click to collapse
Download newest firmware and reflash stock.I think you flashed older firmware.
Thanks for the answer muhamet! The problem is I cannot even get to flash this one since odin stucks at recovery.img. however I am past that because odin can no more do anything in the download mode I am stuck in. I am thinking about something using fastboot or adb, but I dont have any experience to get an idea what may do the job
OblakKoz said:
Thanks for the answer muhamet! The problem is I cannot even get to flash this one since odin stucks at recovery.img. however I am past that because odin can no more do anything in the download mode I am stuck in. I am thinking about something using fastboot or adb, but I dont have any experience to get an idea what may do the job
Click to expand...
Click to collapse
Samsung doesn't have fastboot.You flashed firmware whit old bootloader,because of that you're stuck.Just go to samifirmware and download newest JANUARY firmware and go to download mode.Connect phone to pc press volume up and down same time you will boot to download mode.Then flash firmware.
OblakKoz said:
Thanks for the answer muhamet! The problem is I cannot even get to flash this one since odin stucks at recovery.img. however I am past that because odin can no more do anything in the download mode I am stuck in. I am thinking about something using fastboot or adb, but I dont have any experience to get an idea what may do the job
Click to expand...
Click to collapse
Are you flashing the NON patched TWRP or the PATCHED TWRP ? as you flash the MAGISK_PATCHED file in AP field you must flash the PATCHED TWRP otherwise the phone won't boot
it' same thing with me need help please.i flash file AP with mgisk patched. not worked when try to flash back to official firmware
brounxx said:
it' same thing with me need help please.i flash file AP with mgisk patched. not worked when try to flash back to official firmware
Click to expand...
Click to collapse
check fail (bootloader) device:5 binary:3
lit flash binary - unsupported version
brounxx said:
check fail (bootloader) device:5 binary:3
lit flash binary - unsupported version
Click to expand...
Click to collapse
what must i do?