Im trying to set my phone back to stock after numerous bootloops and nothing works.
Steps ive done:
Ive tried going into recovery and doing a normal new rom install after downloading a new one, been on JBsourcery and its started bootlooping literally for 24 hours or until the battery died.
It kept saying failed after it started to install the the ROM. I even tried reflashing a back up and it also failed.
I downloaded stock rom to flash to odin. It shows connected and runs like normal once i hit start and then it fails. this is the log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> odin.takju.4.3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> bootloader.img
<ID:0/003> radio.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If I try to turn on the device it will show the google logo, blink, google logo again and then takes me to recovery. If anyone can help or point me in right direction to fix, it would be appreciated thanks.
Related
I flashed to Stock with ODIN and it went successful then I downloaded the updated firmware version to flash through ODIN because it wouldn't update through KIES or from itself and half way through, it failed and now it says "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
It doesn't work through Kies, it just keeps trying to connect but no connection so I tried to flashing back to the old firmware through ODIN again and everything works successful until this part
"<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T989UVKL1_HOME_SGH-T989user_CL799405_REV00.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!"
I've tried everything but switch to a different computer to try it on, what do you guys think I should do?
How interesting, after hours and hours of stress, all I did was flash stock recovery through ODIN and now it rebooted fine
Hi,
A brief background...I downloaded and flashed Android_Revolution_HD-Note2_20.1 successfully...
After completing all the things I was checking SU and tried updating it when it asked me i choose TWRP/CWM and the phone restart with bootloop... and can't enter recovery...
What should I do now...I am stuck badly!!! Please help
Thanks in advance
Cheers
additional info
I tried to flash stock rom and it failed
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100DDUEML4_N7100ODDEML2_N7100DDEMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help!!!
I was on T889UVALL4, use Odin to flash root66_TMO_T889UVUCMK7_2.tar.md5, got PASS, phone stuck in boot loop, can not get into recovery mode, so I try flashing again and got the following error. ( i flash KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 with the same result)
Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
here is the Odin log for stock firmware:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My question is: Can this be fix with Odin? or do I need to fix a shop that can repair the EMMC? if it is the latter, does anyone know where to find a trust worthy shop with in the San Francisco bay area?
Thanks
onqq said:
I was on T889UVALL4, use Odin to flash root66_TMO_T889UVUCMK7_2.tar.md5, got PASS, phone stuck in boot loop, can not get into recovery mode, so I try flashing again and got the following error. ( i flash KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 with the same result)
Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
here is the Odin log for stock firmware:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My question is: Can this be fix with Odin? or do I need to fix a shop that can repair the EMMC? if it is the latter, does anyone know where to find a trust worthy shop with in the San Francisco bay area?
Thanks
Click to expand...
Click to collapse
I found a pit file and try flashing with Odin, here is the output:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does that mean my EMMC is corrupted and needs repairing? :crying:
Boot into recovery and Factory/Data Reset
See if that helps
Double0EK said:
Boot into recovery and Factory/Data Reset
See if that helps
Click to expand...
Click to collapse
unfortunately, I can't get into recovery.
when I press volume up+home+power button, I just get a flashing Samsung Galaxy 2 logo (aka boot loop hell)
onqq said:
unfortunately, I can't get into recovery.
when I press volume up+home+power button, I just get a flashing Samsung Galaxy 2 logo (aka boot loop hell)
Click to expand...
Click to collapse
Get the tar file for the most recent TWRP and Odin that. Boot into recovery and factory reset. Try booting normally. If that fails try to Odin the UVALJ1 tar by MrRobinson. (2-3 times). Try booting normally. Once you can boot normally go ahead and try the MK7 tar.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
There are multiple things that can cause it. First try different cables and usb ports. Many times I got stuck like that because odin just didn't like the port I was using. If all else fails you will have to use the Samsung Smart Switch pc app to do an emergency recovery. To find your SN easily go into Download mode by pressing Vol Down + Home + Power then don't hit Vol up instead hit the Home button and it will show your IMEI an SN. then insert your SN into the emergency recovery in Smart Switch.
WARNING!!!!! you will lose all data including your internal sd card. Warning!!!!!
You could try searching around a little here on xda as well. I have read a few posts where people were able to fix it with a specific firmware file. and that was with the FRP lock problem.
randy954 said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
Click to expand...
Click to collapse
you put the G925i firmware on G925T?
Rachy01 said:
you put the G925i firmware on G925T?
Click to expand...
Click to collapse
Bingo!
Give the man a cigar. :sly:
Pp.
Hi guys my step son has proper messed up his phone he's somehow tripped knox and is stuck in a bootloop. I cannot seem to find a current recovery from brick solution for the latest firmwares. The only guide I can find seems to be before knox was implemented I've been looking round and tried one or two guides with no success. I'm really stuck here and am pleading for any help I can get.
Thank you for your help
tell some detailts ..problem is bootloop ? tried Flashing official firm thru odin ?!
Iskander_mal said:
tell some detailts ..problem is bootloop ? tried Flashing official firm thru odin ?!
Click to expand...
Click to collapse
Yes I've tried flashing the official firmware through Odin and I get a massive fail h t t p ://imageshack.com/a/img924/4719/Ou2z5N.jpg
That's what is displayed on the screen
Here's the Odin log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFNE1_N7100BTUFNE1_N7100XXUFND3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> system.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thank you ever so much for taking the time to reply