I tried to do an hard reset following the recommended steps (pressing both '-' keys and soft reset at the same time), appeared the screen 'press 0 to restore' that I have done and after that nothing happens... seems that the i-mate has died!!! screen goes off and nothing happens after.
Could you please help? I'm in Madrid-Spain, should somebody locally could help.
Thanks in advance.
++++++++++++++
UPDATE and FYR
I have connected it to the PC with the USB cable and upgraded it to the latest available from i-mate. It came back to life...!!!
PS: mwang, thanks for your reply.
try to just push reset buttom to see screen come out or not ,otherwide dead.
I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik
Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.
Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.
I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again
Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.
you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.
My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!
they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.
Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )
Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA
Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.
Help!! Brothers
I have tried to update my i600 to wm6 with a flashing program named "I600_WCEDownloader_v1.1_Single" and 3 update files extracted from the official update patch. I downloaded them from MoXXCo.
For the first attempt, around the end of the process, it took a quite long time without any response. I then unplug the battery for another reset... it held at the screen showing "The Ultra messaging". Then, I tried one more "flash" but the update hung up at the end also.
I have no choice but try to re-flash it with the GD1 and GA2 roms. However, during the updating "Phone" part, the phone screen shows the following messages.
[Phone] Active OFF -> Active OFF
[Phone] Reset Pin -> Low : OFF
*[PHONE] Phone Download Failed!
My phone does not have the phone function right now. I find that the Phone version is only blank in the "Version" page, but the eboot and PDA version is shown there. Is there any solution I can do to fix the problem??
I find one more thing but is not sure if it is related. if I do the reset when I go to "Settings" -> "Security" -> "Reset" , and try to hard reset the machine, it fails. Besides, I find that there are three reset options under the "internal" menu, it failed to reset the machine as well.
However, if I use the most common reset method. I switch off the machine and reset the machine by pressing "4-way navigation key UP + Power" simultaneously. After the phone prompts for reset, press 1 and then Y. The phone reset successfully.
Thank you very much!!!
samsung i600 phone download failed
Hi jackylui,
did you found a solution for "Phone download failed" problem? i tried to uprade mine, but have now same problem as you had.
if anyone else knows the solution, please help.
Thanks,
Tomek
Dear experts,
I was trying to change the Start Text in the shellres.dll.0404.mui file (traditional chinese), and initially I was able to find that file. However, after failing to change the Start text (without knowing why), I hard reset it back to factory settings in order to restore and re-edit the file, but that file could not be found anymore... but the system/phone seems to be still working normally.
Can some experts here give me a hand on this please?
Thanks a million!!
VC
Hello everyone, I write from Italy.
I had the problem of generic IMEI (0049 ...), solved by flashing the latest original Samsung rom via Odin also using the PIT.
Now the IMEI is back the original and the phone will work, but I have another problem that I hope you can help me solve.
When I turn on the smartphone appears immediately "the factory test program was arrested" ... but clicking OK the message disappears and you can safely use your phone. At this point, however, I no longer have the lock screen, and if I press the power button to turn off the screen, the phone completely turn off!!!!!! I turn it on again.
Do you help me?
thanks