problems with hard reset - RESOLVED - JASJAR, XDA Exec, MDA Pro Software Upgrading

I tried to do an hard reset following the recommended steps (pressing both '-' keys and soft reset at the same time), appeared the screen 'press 0 to restore' that I have done and after that nothing happens... seems that the i-mate has died!!! screen goes off and nothing happens after.
Could you please help? I'm in Madrid-Spain, should somebody locally could help.
Thanks in advance.
++++++++++++++
UPDATE and FYR
I have connected it to the PC with the USB cable and upgraded it to the latest available from i-mate. It came back to life...!!!
PS: mwang, thanks for your reply.

try to just push reset buttom to see screen come out or not ,otherwide dead.

Related

I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30

I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik
Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.
Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.
I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again
Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.
you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.
My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!
they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.
Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )
Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA
Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.

HELP!!! - Dopod 900 crash after upgrade to WM6

PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
dopod900xxx said:
PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
Click to expand...
Click to collapse
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
From my past experience you have to flash to the original manufacturer rom first. Then you flash to whatever rom you want.
hope this helps
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
dopod900xxx said:
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
Click to expand...
Click to collapse
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
nvatvani said:
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
Click to expand...
Click to collapse
This appears to be a common problem as seen from different posts. Thankfully things are ok after reset.
yes, after reset few times, it works... and everytime it hangs, need reset few times...
dopod900xxx said:
yes, after reset few times, it works... and everytime it hangs, need reset few times...
Click to expand...
Click to collapse
You might find this of interest - it refers to the problem of hanging after soft reset in the 2.01.08 WWE Rom:
jmallen said:
I had this problem also. I found pulling out the battery for 5 or more seconds solved this for me every time.
Give it a try. Good luck
Click to expand...
Click to collapse
It may be solved in later versions.
d_ranade said:
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
Click to expand...
Click to collapse
boss ... please help me ..... i have a dopod 900 ..... but it can not enter bootloader or hard reset .... ditancap usb cable, charger lights flash .... Please help keep the boss. ... thank you
Welcome to forums
Have a read on my signature link, you´ll find a lot of interesting information to recovery your Universal.
Good luck,
flash with tomal roms
Welcome to forums
Tomal ROM´s are indeed fast and stable
manybe you can nmsm your original rom again
Try update bootloader to 1.01 _ttp://rom-update.ru/programs/dd48795954c166e9431f4127c130d474.exe
German Qtek 9000 CID unlocked, hardSPL'd
running MaxStegiROM
Tried to upload D-Two's ROM.
Everything went fine, upload 100%
then: upload error.
screen went black, no reset works
no USB or Serial to be read on dark screen.
Tried battery out (battery is charged), no reaction.
When connecting to PC the red charging LED lights up for
some minutes, then goes off.
PC says connected unknown device ain't working properly
(other Qteks are recognized properly)
Trying to re-flash gives connection error when pressing "update".
Any idea?

Help Need from U

Hi, All
I just tried the WM6 for x51v last night, but my x51 can not boot up any more. The SD image loader processed the image loading without any error and when it asked hard reset, I did right as it said. But after I saw the hard reset screen, which showed "press contact key to restore, press message key to cancel". I tried both keys in diferent hard reset, no one works. The screen got dark again without anything displayed. I waited over 5 minutes to see anything happen. But nothing.
Now the x51 only can show hard reset screen, can not power on. And can not run SD image loader again. Anyone here has any idea about how to solve the problem? Thanks in advance.

WM6 problem HELPPPPPPPP

hi there not sure if my phone is a universal but looks like the pic in the front. anyway i was installin WM6 and when install getdata or sumfink it just went to this blank sceen which says serial v2.01. what do i do nothing works ive tried soft/hard rest nuthin! HELP!!!!!!!
jackador said:
hi there not sure if my phone is a universal but looks like the pic in the front. anyway i was installin WM6 and when install getdata or sumfink it just went to this blank sceen which says serial v2.01. what do i do nothing works ive tried soft/hard rest nuthin! HELP!!!!!!!
Click to expand...
Click to collapse
Remove the battery for 15 minutes or so then re-insert it and try to restart your machine. Note: hard reset requires you to hold down the two - (dash) keys and press the reset button. Some folk (perhaps not you) think that pressing the reset button with the stylus is a hard reset, but that is just a soft one. Good Luck.
you are in the boot loader mode ... read the topic with title :
all of you stuck in bootloader... goodluck.

pls help!!!!wm6 hard reset

hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Have a look here:
- http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
- http://wiki.xda-developers.com/index.php?pagename=BlueAngel_For_Beginners
And next time try this one: http://forum.xda-developers.com/search.php
Greets Rossi
pls help~~~
where? i have ba whit wm6!!! i try all of them for there, not working! there is for ba whit wm5 or wm2003! for wm6 nothing!
helppp!!
on/off + reset button at the same time... not work!
recor+ on\off+reset =serial message on the screen ( i think that is bootloader)
anything alse i need! please helppp!!!
I can't hard reset either
I have followed all of the directions on the wiki, I have even tried to install another rom and it still will not remove all of the data, it changed the information in the about section of my settings but that's it. I want to change ROMs but it is not working. any ideas?
What version of windows is on your PC?
also try the enter BL which is on most ROMs
Hard Reset
To hard reset you do a soft reset (power + reset)
and before it shows the version numbers at the bottom you have to press Record + Camera & also power (i think) and then you come to an options screen using the record button to go down the list and camera to select you select Yes for option 2 and 3 and then hit the mail button to apply.
jidi22 said:
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Click to expand...
Click to collapse
swick off button & rest buton in the same time but take care if is not the original windows you may have problems
Warm Boot: Reset the unit by pressing reset button.
Cold Boot: Press Power ++ Reset the unit simultaneously.
Read this. It's how to hard reset your BA. Hope it helps. Make sure you already formated the storage.
Code:
http://wiki.xda-developers.com/index...izzardUpgrade4

Categories

Resources